diff mbox series

[v4,1/2] dt-bindings: hwmon: ltc2991: add bindings

Message ID 20231012102954.103794-1-antoniu.miclaus@analog.com
State Not Applicable
Headers show
Series [v4,1/2] dt-bindings: hwmon: ltc2991: add bindings | expand

Checks

Context Check Description
robh/checkpatch success
robh/patch-applied success
robh/dtbs-check warning build log
robh/dt-meta-schema success

Commit Message

Antoniu Miclaus Oct. 12, 2023, 10:29 a.m. UTC 
Add dt-bindings for ltc2991 octal i2c voltage, current and temperature
monitor.

Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
---
 .../bindings/hwmon/adi,ltc2991.yaml           | 128 ++++++++++++++++++
 1 file changed, 128 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/hwmon/adi,ltc2991.yaml

Comments

Guenter Roeck Oct. 26, 2023, 1:16 a.m. UTC | #1 
On Thu, Oct 12, 2023 at 01:29:36PM +0300, Antoniu Miclaus wrote:
> Add support for LTC2991 Octal I2C Voltage, Current, and Temperature
> Monitor.
> 
> The LTC2991 is used to monitor system temperatures, voltages and
> currents. Through the I2C serial interface, the eight monitors can
> individually measure supply voltages and can be paired for
> differential measurements of current sense resistors or temperature
> sensing transistors. Additional measurements include internal
> temperature and internal VCC.
> 
> Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
> ---
> changes in v4:
>  - rework ltc2991_read_reg
>  - remove labels
>  - rework channel exposure according to datasheet part typical apllications
>  - avoid division by 0 by checking property value
>  Documentation/hwmon/index.rst   |   1 +
>  Documentation/hwmon/ltc2991.rst |  43 ++++
>  MAINTAINERS                     |   8 +
>  drivers/hwmon/Kconfig           |  11 +
>  drivers/hwmon/Makefile          |   1 +
>  drivers/hwmon/ltc2991.c         | 437 ++++++++++++++++++++++++++++++++
>  6 files changed, 501 insertions(+)
>  create mode 100644 Documentation/hwmon/ltc2991.rst
>  create mode 100644 drivers/hwmon/ltc2991.c
> 
> diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> index 88dadea85cfc..0ec96abe3f7d 100644
> --- a/Documentation/hwmon/index.rst
> +++ b/Documentation/hwmon/index.rst
> @@ -121,6 +121,7 @@ Hardware Monitoring Kernel Drivers
>     ltc2947
>     ltc2978
>     ltc2990
> +   ltc2991
>     ltc3815
>     ltc4151
>     ltc4215
> diff --git a/Documentation/hwmon/ltc2991.rst b/Documentation/hwmon/ltc2991.rst
> new file mode 100644
> index 000000000000..9ab29dd85012
> --- /dev/null
> +++ b/Documentation/hwmon/ltc2991.rst
> @@ -0,0 +1,43 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +Kernel driver ltc2991
> +=====================
> +
> +Supported chips:
> +
> +  * Analog Devices LTC2991
> +
> +    Prefix: 'ltc2991'
> +
> +    Addresses scanned: I2C 0x48 - 0x4f
> +
> +    Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/2991ff.pdf
> +
> +Authors:
> +
> +  - Antoniu Miclaus <antoniu.miclaus@analog.com>
> +
> +
> +Description
> +-----------
> +
> +This driver supports hardware monitoring for Analog Devices LTC2991 Octal I2C
> +Voltage, Current and Temperature Monitor.
> +
> +The LTC2991 is used to monitor system temperatures, voltages and currents.
> +Through the I2C serial interface, the eight monitors can individually measure
> +supply voltages and can be paired for differential measurements of current sense
> +resistors or temperature sensing transistors. Additional measurements include
> +internal temperatureand internal VCC.
> +
> +
> +sysfs-Interface
> +-------------
> +
> +The following attributes are supported. Limits are read-only.
> +
> +=============== =================
> +inX_input:      voltage input
> +currX_input:    current input
> +tempX_input:    temperature input
> +=============== =================
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 6c4cce45a09d..edfa49c42848 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12449,6 +12449,14 @@ F:	drivers/hwmon/ltc2947-i2c.c
>  F:	drivers/hwmon/ltc2947-spi.c
>  F:	drivers/hwmon/ltc2947.h
>  
> +LTC2991 HARDWARE MONITOR DRIVER
> +M:	Antoniu Miclaus <antoniu.miclaus@analog.com>
> +L:	linux-hwmon@vger.kernel.org
> +S:	Supported
> +W:	https://ez.analog.com/linux-software-drivers
> +F:	Documentation/devicetree/bindings/hwmon/adi,ltc2991.yaml
> +F:	drivers/hwmon/ltc2991.c
> +
>  LTC2983 IIO TEMPERATURE DRIVER
>  M:	Nuno Sá <nuno.sa@analog.com>
>  L:	linux-iio@vger.kernel.org
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index ec38c8892158..818a67328fcd 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -932,6 +932,17 @@ config SENSORS_LTC2990
>  	  This driver can also be built as a module. If so, the module will
>  	  be called ltc2990.
>  
> +config SENSORS_LTC2991
> +	tristate "Analog Devices LTC2991"
> +	depends on I2C
> +	help
> +	  If you say yes here you get support for Analog Devices LTC2991
> +	  Octal I2C Voltage, Current, and Temperature Monitor. The LTC2991
> +	  supports a combination of voltage, current and temperature monitoring.
> +
> +	  This driver can also be built as a module. If so, the module will
> +	  be called ltc2991.
> +
>  config SENSORS_LTC2992
>  	tristate "Linear Technology LTC2992"
>  	depends on I2C
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index 4ac9452b5430..f324d057535a 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -127,6 +127,7 @@ obj-$(CONFIG_SENSORS_LTC2947)	+= ltc2947-core.o
>  obj-$(CONFIG_SENSORS_LTC2947_I2C) += ltc2947-i2c.o
>  obj-$(CONFIG_SENSORS_LTC2947_SPI) += ltc2947-spi.o
>  obj-$(CONFIG_SENSORS_LTC2990)	+= ltc2990.o
> +obj-$(CONFIG_SENSORS_LTC2991)	+= ltc2991.o
>  obj-$(CONFIG_SENSORS_LTC2992)	+= ltc2992.o
>  obj-$(CONFIG_SENSORS_LTC4151)	+= ltc4151.o
>  obj-$(CONFIG_SENSORS_LTC4215)	+= ltc4215.o
> diff --git a/drivers/hwmon/ltc2991.c b/drivers/hwmon/ltc2991.c
> new file mode 100644
> index 000000000000..4f3d73bc494a
> --- /dev/null
> +++ b/drivers/hwmon/ltc2991.c
> @@ -0,0 +1,437 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2023 Analog Devices, Inc.
> + * Author: Antoniu Miclaus <antoniu.miclaus@analog.com>
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/err.h>
> +#include <linux/hwmon.h>
> +#include <linux/hwmon-sysfs.h>

I don't see why this include file would be needed.

> +#include <linux/i2c.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +
> +#include <asm/unaligned.h>

There are no unaligned accesses, so it appears
that this include is not needed either.

> +
> +#define LTC2991_STATUS_LOW		0x00
> +#define LTC2991_CH_EN_TRIGGER		0x01
> +#define LTC2991_V1_V4_CTRL		0x06
> +#define LTC2991_V5_V8_CTRL		0x07
> +#define LTC2991_PWM_TH_LSB_T_INT	0x08
> +#define LTC2991_PWM_TH_MSB		0x09
> +#define LTC2991_CHANNEL_V_MSB(x)	(0x0A + ((x) * 2))
> +#define LTC2991_CHANNEL_T_MSB(x)	(0x0A + ((x) * 4))
> +#define LTC2991_CHANNEL_C_MSB(x)	(0x0C + ((x) * 4))
> +#define LTC2991_T_INT_MSB		0x1A
> +#define LTC2991_VCC_MSB			0x1C
> +
> +#define LTC2991_V7_V8_EN		BIT(7)
> +#define LTC2991_V5_V6_EN		BIT(6)
> +#define LTC2991_V3_V4_EN		BIT(5)
> +#define LTC2991_V1_V2_EN		BIT(4)
> +#define LTC2991_T_INT_VCC_EN		BIT(3)
> +
> +#define LTC2991_V3_V4_FILT_EN		BIT(7)
> +#define LTC2991_V3_V4_TEMP_EN		BIT(5)
> +#define LTC2991_V3_V4_DIFF_EN		BIT(4)
> +#define LTC2991_V1_V2_FILT_EN		BIT(3)
> +#define LTC2991_V1_V2_TEMP_EN		BIT(1)
> +#define LTC2991_V1_V2_DIFF_EN		BIT(0)
> +
> +#define LTC2991_V7_V8_FILT_EN		BIT(7)
> +#define LTC2991_V7_V8_TEMP_EN		BIT(5)
> +#define LTC2991_V7_V8_DIFF_EN		BIT(4)
> +#define LTC2991_V5_V6_FILT_EN		BIT(7)
> +#define LTC2991_V5_V6_TEMP_EN		BIT(5)
> +#define LTC2991_V5_V6_DIFF_EN		BIT(4)
> +
> +#define LTC2991_REPEAT_ACQ_EN		BIT(4)
> +#define LTC2991_T_INT_FILT_EN		BIT(3)
> +
> +#define LTC2991_MAX_CHANNEL		4
> +#define LTC2991_T_INT_CH_NR		4
> +#define LTC2991_VCC_CH_NR		0
> +
> +struct ltc2991_state {
> +	struct i2c_client	*client;

This is only used in the init function, and each time it is used
it is derefernced as &st->client->dev. Just pass dev as parameter
and be done with it.

> +	struct regmap		*regmap;
> +	u32			r_sense_uohm[LTC2991_MAX_CHANNEL];
> +	bool			temp_en[LTC2991_MAX_CHANNEL];
> +};
> +
> +static int ltc2991_read_reg(struct ltc2991_state *st, u8 addr, u8 reg_len,
> +			    int *val)
> +{
> +	__be16 regvals;
> +	int ret;
> +
> +	if (reg_len < 2)
> +		return regmap_read(st->regmap, addr, val);
> +
> +	ret = regmap_bulk_read(st->regmap, addr, &regvals, reg_len);
> +	if (ret)
> +		return ret;
> +
> +	*val = be16_to_cpu(regvals);
> +
> +	return 0;
> +}
> +
> +static int ltc2991_get_voltage(struct ltc2991_state *st, u32 reg, long *val)
> +{
> +	int reg_val, ret, offset = 0;
> +
> +	ret = ltc2991_read_reg(st, reg, 2, &reg_val);
> +	if (ret)
> +		return ret;
> +
> +	if (reg == LTC2991_VCC_MSB)
> +		/* Vcc 2.5V offset */
> +		offset = 2500;
> +
> +	/* Vx, 305.18uV/LSB */
> +	*val = DIV_ROUND_CLOSEST(sign_extend32(reg_val, 14) * 30518,
> +				 1000 * 100) + offset;
> +
> +	return 0;
> +}
> +
> +static int ltc2991_read_in(struct device *dev, u32 attr, int channel, long *val)
> +{
> +	struct ltc2991_state *st = dev_get_drvdata(dev);
> +	u32 reg;
> +
> +	switch (attr) {
> +	case hwmon_in_input:
> +		if (channel == LTC2991_VCC_CH_NR)
> +			reg = LTC2991_VCC_MSB;
> +		else
> +			reg = LTC2991_CHANNEL_V_MSB(channel - 1);
> +
> +		return ltc2991_get_voltage(st, reg, val);
> +	default:
> +		return -EOPNOTSUPP;
> +	}
> +}
> +
> +static int ltc2991_get_curr(struct ltc2991_state *st, u32 reg, int channel,
> +			    long *val)
> +{
> +	int reg_val, ret;
> +
> +	ret = ltc2991_read_reg(st, reg, 2, &reg_val);
> +	if (ret)
> +		return ret;
> +
> +	/* Vx-Vy, 19.075uV/LSB */
> +	*val = DIV_ROUND_CLOSEST(sign_extend32(reg_val, 14) * 19075, 1000)
> +				 / (st->r_sense_uohm[channel] / 1000);

If st->r_sense_uohm[channel] < 1000, the divide operation will
result in a division by zero error. Also, there is a loss of
accuracy because the sense resistor is rounded to mOhm before
being used.

> +
> +	return 0;
> +}
> +
> +static int ltc2991_read_curr(struct device *dev, u32 attr, int channel,
> +			     long *val)
> +{
> +	struct ltc2991_state *st = dev_get_drvdata(dev);
> +	u32 reg;
> +
> +	switch (attr) {
> +	case hwmon_curr_input:
> +		reg = LTC2991_CHANNEL_C_MSB(channel);
> +		return ltc2991_get_curr(st, reg, channel, val);
> +	default:
> +		return -EOPNOTSUPP;
> +	}
> +}
> +
> +static int ltc2991_get_temp(struct ltc2991_state *st, u32 reg, int channel,
> +			    long *val)
> +{
> +	int reg_val, ret;
> +
> +	ret = ltc2991_read_reg(st, reg, 2, &reg_val);
> +	if (ret)
> +		return ret;
> +
> +	/* Temp LSB = 0.0625 Degrees */
> +	*val = DIV_ROUND_CLOSEST(sign_extend32(reg_val, 12) * 1000, 16);
> +
> +	return 0;
> +}
> +
> +static int ltc2991_read_temp(struct device *dev, u32 attr, int channel,
> +			     long *val)
> +{
> +	struct ltc2991_state *st = dev_get_drvdata(dev);
> +	u32 reg;
> +
> +	switch (attr) {
> +	case hwmon_temp_input:
> +		if (channel == LTC2991_T_INT_CH_NR)
> +			reg = LTC2991_T_INT_MSB;
> +		else
> +			reg = LTC2991_CHANNEL_T_MSB(channel);
> +
> +		return ltc2991_get_temp(st, reg, channel, val);
> +	default:
> +		return -EOPNOTSUPP;
> +	}
> +}
> +
> +static int ltc2991_read(struct device *dev, enum hwmon_sensor_types type,
> +			u32 attr, int channel, long *val)
> +{
> +	switch (type) {
> +	case hwmon_in:
> +		return ltc2991_read_in(dev, attr, channel, val);
> +	case hwmon_curr:
> +		return ltc2991_read_curr(dev, attr, channel, val);
> +	case hwmon_temp:
> +		return ltc2991_read_temp(dev, attr, channel, val);
> +	default:
> +		return -EOPNOTSUPP;
> +	}
> +}
> +
> +static umode_t ltc2991_is_visible(const void *data,
> +				  enum hwmon_sensor_types type, u32 attr,
> +				  int channel)
> +{
> +	const struct ltc2991_state *st = data;
> +
> +	switch (type) {
> +	case hwmon_in:
> +		switch (attr) {
> +		case hwmon_in_input:
> +			if (channel == LTC2991_VCC_CH_NR)
> +				return 0444;
> +			if (st->temp_en[(channel - 1) / 2])
> +				break;
> +			if (channel % 2)
> +				return 0444;
> +			if (!st->r_sense_uohm[(channel - 1) / 2])
> +				return 0444;
> +		}
> +		break;
> +	case hwmon_curr:
> +		switch (attr) {
> +		case hwmon_curr_input:
> +			if (st->r_sense_uohm[channel])
> +				return 0444;
> +			break;
> +		}
> +		break;
> +	case hwmon_temp:
> +		switch (attr) {
> +		case hwmon_temp_input:
> +			if (st->temp_en[channel] ||
> +			    channel == LTC2991_T_INT_CH_NR)
> +				return 0444;
> +			break;
> +		}
> +		break;
> +	default:
> +		break;
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct hwmon_ops ltc2991_hwmon_ops = {
> +	.is_visible = ltc2991_is_visible,
> +	.read = ltc2991_read,
> +};
> +
> +static const struct hwmon_channel_info *ltc2991_info[] = {
> +	HWMON_CHANNEL_INFO(temp,
> +			   HWMON_T_INPUT,
> +			   HWMON_T_INPUT,
> +			   HWMON_T_INPUT,
> +			   HWMON_T_INPUT,
> +			   HWMON_T_INPUT
> +			   ),
> +	HWMON_CHANNEL_INFO(curr,
> +			   HWMON_C_INPUT,
> +			   HWMON_C_INPUT,
> +			   HWMON_C_INPUT,
> +			   HWMON_C_INPUT
> +			   ),
> +	HWMON_CHANNEL_INFO(in,
> +			   HWMON_I_INPUT,
> +			   HWMON_I_INPUT,
> +			   HWMON_I_INPUT,
> +			   HWMON_I_INPUT,
> +			   HWMON_I_INPUT,
> +			   HWMON_I_INPUT,
> +			   HWMON_I_INPUT,
> +			   HWMON_I_INPUT,
> +			   HWMON_I_INPUT
> +			   ),
> +	NULL
> +};
> +
> +static const struct hwmon_chip_info ltc2991_chip_info = {
> +	.ops = &ltc2991_hwmon_ops,
> +	.info = ltc2991_info,
> +};
> +
> +static const struct regmap_config ltc2991_regmap_config = {
> +	.reg_bits = 8,
> +	.val_bits = 8,
> +	.max_register = 0x1D,
> +};
> +
> +static int ltc2991_init(struct ltc2991_state *st)
> +{
> +	struct fwnode_handle *child;
> +	int ret;
> +	u32 val, addr;
> +	u8 v5_v8_reg_data = 0, v1_v4_reg_data = 0;
> +
> +	ret = devm_regulator_get_enable(&st->client->dev, "vcc");
> +	if (ret)
> +		return dev_err_probe(&st->client->dev, ret,
> +				     "failed to enable regulator\n");
> +
> +	device_for_each_child_node(&st->client->dev, child) {
> +		ret = fwnode_property_read_u32(child, "reg", &addr);
> +		if (ret < 0) {
> +			fwnode_handle_put(child);
> +			return ret;
> +		}
> +
> +		if (addr > 3) {
> +			fwnode_handle_put(child);
> +			return -EINVAL;
> +		}
> +
> +		ret = fwnode_property_read_u32(child, "shunt-resistor-micro-ohms", &val);
> +		if (!ret) {
> +			if (!val)
> +				return dev_err_probe(&st->client->dev, -EINVAL,
> +						     "shunt resistor value cannot be zero\n");
> +
> +			st->r_sense_uohm[addr] = val;
> +
> +			switch (addr) {
> +			case 0:
> +				v1_v4_reg_data |= LTC2991_V1_V2_DIFF_EN;
> +				break;
> +			case 1:
> +				v1_v4_reg_data |= LTC2991_V3_V4_DIFF_EN;
> +				break;
> +			case 2:
> +				v5_v8_reg_data |= LTC2991_V5_V6_DIFF_EN;
> +				break;
> +			case 3:
> +				v5_v8_reg_data |= LTC2991_V7_V8_DIFF_EN;
> +				break;
> +			default:
> +				break;
> +			}
> +		}
> +
> +		ret = fwnode_property_read_bool(child, "adi,temperature-enable");
> +		if (ret) {
> +			st->temp_en[addr] = ret;
> +
> +			switch (addr) {
> +			case 0:
> +				v1_v4_reg_data |= LTC2991_V1_V2_TEMP_EN;
> +				break;
> +			case 1:
> +				v1_v4_reg_data |= LTC2991_V3_V4_TEMP_EN;
> +				break;
> +			case 2:
> +				v5_v8_reg_data |= LTC2991_V5_V6_TEMP_EN;
> +				break;
> +			case 3:
> +				v5_v8_reg_data |= LTC2991_V7_V8_TEMP_EN;
> +				break;
> +			default:
> +				break;
> +			}
> +		}
> +	}
> +
> +	ret = regmap_write(st->regmap, LTC2991_V5_V8_CTRL, v5_v8_reg_data);
> +	if (ret)
> +		return dev_err_probe(&st->client->dev, ret,
> +				     "Error: Failed to set V5-V8 CTRL reg.\n");
> +
> +	ret = regmap_write(st->regmap, LTC2991_V1_V4_CTRL, v1_v4_reg_data);
> +	if (ret)
> +		return dev_err_probe(&st->client->dev, ret,
> +				     "Error: Failed to set V1-V4 CTRL reg.\n");
> +
> +	ret = regmap_write(st->regmap, LTC2991_PWM_TH_LSB_T_INT,
> +			   LTC2991_REPEAT_ACQ_EN);
> +	if (ret)
> +		return dev_err_probe(&st->client->dev, ret,
> +				     "Error: Failed to set contiuous mode.\n");
> +
> +	/* Enable all channels and trigger conversions */
> +	return regmap_write(st->regmap, LTC2991_CH_EN_TRIGGER,
> +			    LTC2991_V7_V8_EN | LTC2991_V5_V6_EN |
> +			    LTC2991_V3_V4_EN | LTC2991_V1_V2_EN |
> +			    LTC2991_T_INT_VCC_EN);
> +}
> +
> +static int ltc2991_i2c_probe(struct i2c_client *client)
> +{
> +	int ret;
> +	struct device *hwmon_dev;
> +	struct ltc2991_state *st;
> +
> +	st = devm_kzalloc(&client->dev, sizeof(*st), GFP_KERNEL);
> +	if (!st)
> +		return -ENOMEM;
> +
> +	st->client = client;
> +	st->regmap = devm_regmap_init_i2c(client, &ltc2991_regmap_config);
> +	if (IS_ERR(st->regmap))
> +		return PTR_ERR(st->regmap);
> +
> +	ret = ltc2991_init(st);
> +	if (ret)
> +		return ret;
> +
> +	hwmon_dev = devm_hwmon_device_register_with_info(&client->dev,
> +							 client->name, st,
> +							 &ltc2991_chip_info,
> +							 NULL);
> +
> +	return PTR_ERR_OR_ZERO(hwmon_dev);
> +}
> +
> +static const struct of_device_id ltc2991_of_match[] = {
> +	{ .compatible = "adi,ltc2991" },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, ltc2991_of_match);
> +
> +static const struct i2c_device_id ltc2991_i2c_id[] = {
> +	{ "ltc2991", 0 },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(i2c, ltc2991_i2c_id);
> +
> +static struct i2c_driver ltc2991_i2c_driver = {
> +	.driver = {
> +		.name = "ltc2991",
> +		.of_match_table = ltc2991_of_match,
> +	},
> +	.probe = ltc2991_i2c_probe,
> +	.id_table = ltc2991_i2c_id,
> +};
> +
> +module_i2c_driver(ltc2991_i2c_driver);
> +
> +MODULE_AUTHOR("Antoniu Miclaus <antoniu.miclaus@analog.com>");
> +MODULE_DESCRIPTION("Analog Devices LTC2991 HWMON Driver");
> +MODULE_LICENSE("GPL");
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/hwmon/adi,ltc2991.yaml b/Documentation/devicetree/bindings/hwmon/adi,ltc2991.yaml
new file mode 100644
index 000000000000..011e5b65c79c
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/adi,ltc2991.yaml
@@ -0,0 +1,128 @@ 
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+
+$id: http://devicetree.org/schemas/hwmon/adi,ltc2991.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices LTC2991 Octal I2C Voltage, Current and Temperature Monitor
+
+maintainers:
+  - Antoniu Miclaus <antoniu.miclaus@analog.com>
+
+description: |
+  The LTC2991 is used to monitor system temperatures, voltages and currents.
+  Through the I2C serial interface, the eight monitors can individually measure
+  supply voltages and can be paired for differential measurements of current
+  sense resistors or temperature sensing transistors.
+
+  Datasheet:
+    https://www.analog.com/en/products/ltc2991.html
+
+properties:
+  compatible:
+    const: adi,ltc2991
+
+  reg:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  vcc-supply: true
+
+patternProperties:
+  "^channel@[0-3]$":
+    type: object
+    description:
+      Represents the differential/temperature channels.
+
+    properties:
+      reg:
+        description:
+          The channel number. LTC2991 can monitor 4 currents/temperatures.
+        items:
+          minimum: 0
+          maximum: 3
+
+      shunt-resistor-micro-ohms:
+        description:
+          The value of curent sense resistor in micro ohms. Pin configuration is
+          set for differential input pair.
+
+      adi,temperature-enable:
+        description:
+          Enables temperature readings. Pin configuration is set for remote
+          diode temperature measurement.
+        type: boolean
+
+    required:
+      - reg
+
+    allOf:
+      - if:
+          required:
+            - shunt-resistor-micro-ohms
+        then:
+          properties:
+            adi,temperature-enable: false
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - vcc-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        hwmon@48 {
+            compatible = "adi,ltc2991";
+            reg = <0x48>;
+            vcc-supply = <&vcc>;
+        };
+    };
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        hwmon@48 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            compatible = "adi,ltc2991";
+            reg = <0x48>;
+            vcc-supply = <&vcc>;
+
+            channel@0 {
+                    reg = <0x0>;
+                    shunt-resistor-micro-ohms = <100000>;
+            };
+
+            channel@1 {
+                    reg = <0x1>;
+                    shunt-resistor-micro-ohms = <100000>;
+            };
+
+            channel@2 {
+                    reg = <0x2>;
+                    adi,temperature-enable;
+            };
+
+            channel@3 {
+                    reg = <0x3>;
+                    adi,temperature-enable;
+            };
+        };
+    };
+...