deleted file mode 100644
@@ -1,143 +0,0 @@
-* NVIDIA Tegra Secure Digital Host Controller
-
-This controller on Tegra family SoCs provides an interface for MMC, SD,
-and SDIO types of memory cards.
-
-This file documents differences between the core properties described
-by mmc.txt and the properties used by the sdhci-tegra driver.
-
-Required properties:
-- compatible : should be one of:
- - "nvidia,tegra20-sdhci": for Tegra20
- - "nvidia,tegra30-sdhci": for Tegra30
- - "nvidia,tegra114-sdhci": for Tegra114
- - "nvidia,tegra124-sdhci": for Tegra124 and Tegra132
- - "nvidia,tegra210-sdhci": for Tegra210
- - "nvidia,tegra186-sdhci": for Tegra186
- - "nvidia,tegra194-sdhci": for Tegra194
-- clocks: For Tegra210, Tegra186 and Tegra194 must contain two entries.
- One for the module clock and one for the timeout clock.
- For all other Tegra devices, must contain a single entry for
- the module clock. See ../clocks/clock-bindings.txt for details.
-- clock-names: For Tegra210, Tegra186 and Tegra194 must contain the
- strings 'sdhci' and 'tmclk' to represent the module and
- the timeout clocks, respectively.
- For all other Tegra devices must contain the string 'sdhci'
- to represent the module clock.
-- resets : Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
-- reset-names : Must include the following entries:
- - sdhci
-
-Optional properties:
-- power-gpios : Specify GPIOs for power control
-
-Example:
-
-sdhci@c8000200 {
- compatible = "nvidia,tegra20-sdhci";
- reg = <0xc8000200 0x200>;
- interrupts = <47>;
- clocks = <&tegra_car 14>;
- resets = <&tegra_car 14>;
- reset-names = "sdhci";
- cd-gpios = <&gpio 69 0>; /* gpio PI5 */
- wp-gpios = <&gpio 57 0>; /* gpio PH1 */
- power-gpios = <&gpio 155 0>; /* gpio PT3 */
- bus-width = <8>;
-};
-
-Optional properties for Tegra210, Tegra186 and Tegra194:
-- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage
- configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8"
- for controllers supporting multiple voltage levels. The order of names
- should correspond to the pin configuration states in pinctrl-0 and
- pinctrl-1.
-- pinctrl-names : "sdmmc-3v3-drv" and "sdmmc-1v8-drv" are applicable for
- Tegra210 where pad config registers are in the pinmux register domain
- for pull-up-strength and pull-down-strength values configuration when
- using pads at 3V3 and 1V8 levels.
-- nvidia,only-1-8-v : The presence of this property indicates that the
- controller operates at a 1.8 V fixed I/O voltage.
-- nvidia,pad-autocal-pull-up-offset-3v3,
- nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength
- calibration offsets for 3.3 V signaling modes.
-- nvidia,pad-autocal-pull-up-offset-1v8,
- nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength
- calibration offsets for 1.8 V signaling modes.
-- nvidia,pad-autocal-pull-up-offset-3v3-timeout,
- nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive
- strength used as a fallback in case the automatic calibration times
- out on a 3.3 V signaling mode.
-- nvidia,pad-autocal-pull-up-offset-1v8-timeout,
- nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive
- strength used as a fallback in case the automatic calibration times
- out on a 1.8 V signaling mode.
-- nvidia,pad-autocal-pull-up-offset-sdr104,
- nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength
- calibration offsets for SDR104 mode.
-- nvidia,pad-autocal-pull-up-offset-hs400,
- nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength
- calibration offsets for HS400 mode.
-- nvidia,default-tap : Specify the default inbound sampling clock
- trimmer value for non-tunable modes.
-- nvidia,default-trim : Specify the default outbound clock trimmer
- value.
-- nvidia,dqs-trim : Specify DQS trim value for HS400 timing
-
- Notes on the pad calibration pull up and pulldown offset values:
- - The property values are drive codes which are programmed into the
- PD_OFFSET and PU_OFFSET sections of the
- SDHCI_TEGRA_AUTO_CAL_CONFIG register.
- - A higher value corresponds to higher drive strength. Please refer
- to the reference manual of the SoC for correct values.
- - The SDR104 and HS400 timing specific values are used in
- corresponding modes if specified.
-
- Notes on tap and trim values:
- - The values are used for compensating trace length differences
- by adjusting the sampling point.
- - The values are programmed to the Vendor Clock Control Register.
- Please refer to the reference manual of the SoC for correct
- values.
- - The DQS trim values are only used on controllers which support
- HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports
- HS400.
-
-Example:
-sdhci@700b0000 {
- compatible = "nvidia,tegra124-sdhci";
- reg = <0x0 0x700b0000 0x0 0x200>;
- interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&tegra_car TEGRA210_CLK_SDMMC1>;
- clock-names = "sdhci";
- resets = <&tegra_car 14>;
- reset-names = "sdhci";
- pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
- pinctrl-0 = <&sdmmc1_3v3>;
- pinctrl-1 = <&sdmmc1_1v8>;
- nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
- nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
- nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
- nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>;
- status = "disabled";
-};
-
-sdhci@700b0000 {
- compatible = "nvidia,tegra210-sdhci";
- reg = <0x0 0x700b0000 0x0 0x200>;
- interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&tegra_car TEGRA210_CLK_SDMMC1>,
- <&tegra_car TEGRA210_CLK_SDMMC_LEGACY>;
- clock-names = "sdhci", "tmclk";
- resets = <&tegra_car 14>;
- reset-names = "sdhci";
- pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
- pinctrl-0 = <&sdmmc1_3v3>;
- pinctrl-1 = <&sdmmc1_1v8>;
- nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
- nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
- nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
- nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>;
- status = "disabled";
-};
new file mode 100644
@@ -0,0 +1,294 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/nvidia,tegra20-sdhci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra Secure Digital Host Controller
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+description: |
+ This controller on Tegra family SoCs provides an interface for MMC, SD, and
+ SDIO types of memory cards.
+
+ This file documents differences between the core properties described by
+ mmc-controller.yaml and the properties for the Tegra SDHCI controller.
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - nvidia,tegra20-sdhci
+ - nvidia,tegra30-sdhci
+ - nvidia,tegra114-sdhci
+ - nvidia,tegra124-sdhci
+ - nvidia,tegra210-sdhci
+ - nvidia,tegra186-sdhci
+ - nvidia,tegra194-sdhci
+
+ - items:
+ - const: nvidia,tegra132-sdhci
+ - const: nvidia,tegra124-sdhci
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ assigned-clocks: true
+ assigned-clock-parents: true
+ assigned-clock-rates: true
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ minItems: 1
+ maxItems: 2
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: sdhci
+
+ power-gpios:
+ description: specify GPIOs for power control
+ maxItems: 1
+
+ iommus:
+ maxItems: 1
+
+ nvidia,default-tap:
+ description: Specify the default inbound sampling clock trimmer value for
+ non-tunable modes.
+
+ The values are used for compensating trace length differences by
+ adjusting the sampling point. The values are programmed to the Vendor
+ Clock Control Register. Please refer to the reference manual of the SoC
+ for correct values.
+
+ The DQS trim values are only used on controllers which support HS400
+ timing. Only SDMMC4 on Tegra210 and Tegra186 supports HS400.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,default-trim:
+ description: Specify the default outbound clock trimmer value.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,dqs-trim:
+ description: Specify DQS trim value for HS400 timing.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-down-offset-1v8:
+ description: Specify drive strength calibration offsets for 1.8 V
+ signaling modes.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-down-offset-1v8-timeout:
+ description: Specify drive strength used as a fallback in case the
+ automatic calibration times out on a 1.8 V signaling mode.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-down-offset-3v3:
+ description: Specify drive strength calibration offsets for 3.3 V
+ signaling modes.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-down-offset-3v3-timeout:
+ description: Specify drive strength used as a fallback in case the
+ automatic calibration times out on a 3.3 V signaling mode.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-down-offset-sdr104:
+ description: Specify drive strength calibration offsets for SDR104 mode.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-down-offset-hs400:
+ description: Specify drive strength calibration offsets for HS400 mode.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-up-offset-1v8:
+ description: Specify drive strength calibration offsets for 1.8 V
+ signaling modes.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-up-offset-1v8-timeout:
+ description: Specify drive strength used as a fallback in case the
+ automatic calibration times out on a 1.8 V signaling mode.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-up-offset-3v3:
+ description: Specify drive strength calibration offsets for 3.3 V
+ signaling modes.
+
+ The property values are drive codes which are programmed into the
+ PD_OFFSET and PU_OFFSET sections of the SDHCI_TEGRA_AUTO_CAL_CONFIG
+ register. A higher value corresponds to higher drive strength. Please
+ refer to the reference manual of the SoC for correct values. The SDR104
+ and HS400 timing specific values are used in corresponding modes if
+ specified.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-up-offset-3v3-timeout:
+ description: Specify drive strength used as a fallback in case the
+ automatic calibration times out on a 3.3 V signaling mode.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-up-offset-sdr104:
+ description: Specify drive strength calibration offsets for SDR104 mode.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,pad-autocal-pull-up-offset-hs400:
+ description: Specify drive strength calibration offsets for HS400 mode.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,only-1-8v:
+ description: The presence of this property indicates that the controller
+ operates at a 1.8 V fixed I/O voltage.
+ $ref: "/schemas/types.yaml#/definitions/flag"
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - resets
+ - reset-names
+
+allOf:
+ - $ref: "mmc-controller.yaml"
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra20-sdhci
+ - nvidia,tegra30-sdhci
+ - nvidia,tegra114-sdhci
+ - nvidia,tegra124-sdhci
+ clocks:
+ items:
+ - description: module clock
+ minItems: 1
+ maxItems: 1
+ else:
+ properties:
+ clocks:
+ items:
+ - description: module clock
+ - description: timeout clock
+ minItems: 2
+ maxItems: 2
+ clock-names:
+ items:
+ - const: sdhci
+ - const: tmclk
+ minItems: 2
+ maxItems: 2
+ required:
+ - clock-names
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra210-sdhci
+ then:
+ properties:
+ pinctrl-names:
+ oneOf:
+ - items:
+ - const: sdmmc-3v3
+ description: pad configuration for 3.3 V
+ - const: sdmmc-1v8
+ description: pad configuration for 1.8 V
+ - const: sdmmc-3v3-drv
+ description: pull-up/down configuration for 3.3 V
+ - const: sdmmc-1v8-drv
+ description: pull-up/down configuration for 1.8 V
+ - items:
+ - const: sdmmc-3v3-drv
+ description: pull-up/down configuration for 3.3 V
+ - const: sdmmc-1v8-drv
+ description: pull-up/down configuration for 1.8 V
+ - items:
+ - const: sdmmc-1v8-drv
+ description: pull-up/down configuration for 1.8 V
+ required:
+ - clock-names
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra186-sdhci
+ - nvidia,tegra194-sdhci
+ then:
+ properties:
+ pinctrl-names:
+ items:
+ - const: sdmmc-3v3
+ description: pad configuration for 3.3 V
+ - const: sdmmc-1v8
+ description: pad configuration for 1.8 V
+ required:
+ - clock-names
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ mmc@c8000200 {
+ compatible = "nvidia,tegra20-sdhci";
+ reg = <0xc8000200 0x200>;
+ interrupts = <47>;
+ clocks = <&tegra_car 14>;
+ resets = <&tegra_car 14>;
+ reset-names = "sdhci";
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 155 0>; /* gpio PT3 */
+ bus-width = <8>;
+ };
+
+ - |
+ #include <dt-bindings/clock/tegra210-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ mmc@700b0000 {
+ compatible = "nvidia,tegra210-sdhci";
+ reg = <0x700b0000 0x200>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA210_CLK_SDMMC1>,
+ <&tegra_car TEGRA210_CLK_SDMMC_LEGACY>;
+ clock-names = "sdhci", "tmclk";
+ resets = <&tegra_car 14>;
+ reset-names = "sdhci";
+ pinctrl-names = "sdmmc-3v3", "sdmmc-1v8",
+ "sdmmc-3v3-drv", "sdmmc-1v8-drv";
+ pinctrl-0 = <&sdmmc1_3v3>;
+ pinctrl-1 = <&sdmmc1_1v8>;
+ pinctrl-2 = <&sdmmc1_3v3_drv>;
+ pinctrl-3 = <&sdmmc1_1v8_drv>;
+ nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
+ nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
+ nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
+ nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>;
+ nvidia,default-tap = <0x2>;
+ nvidia,default-trim = <0x4>;
+ assigned-clocks = <&tegra_car TEGRA210_CLK_SDMMC4>,
+ <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>,
+ <&tegra_car TEGRA210_CLK_PLL_C4>;
+ assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>;
+ assigned-clock-rates = <200000000>, <1000000000>, <1000000000>;
+ };