diff mbox series

[v4,1/4] dt-bindings: phy: Add sparx5-serdes bindings

Message ID 20201120150359.2041940-2-steen.hegelund@microchip.com
State Superseded
Headers show
Series [v4,1/4] dt-bindings: phy: Add sparx5-serdes bindings | expand

Checks

Context Check Description
robh/dt-meta-schema success
robh/checkpatch success

Commit Message

Steen Hegelund Nov. 20, 2020, 3:03 p.m. UTC
Document the Sparx5 ethernet serdes phy driver bindings.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
---
 .../bindings/phy/microchip,sparx5-serdes.yaml | 296 ++++++++++++++++++
 1 file changed, 296 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml

Comments

Alexandre Belloni Nov. 20, 2020, 4:09 p.m. UTC | #1
Hi,

On 20/11/2020 16:03:56+0100, Steen Hegelund wrote:
> Document the Sparx5 ethernet serdes phy driver bindings.
> 
> Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
> Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
> ---
>  .../bindings/phy/microchip,sparx5-serdes.yaml | 296 ++++++++++++++++++
>  1 file changed, 296 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml
> 
> diff --git a/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml b/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml
> new file mode 100644
> index 000000000000..0bfb752e7686
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml
> @@ -0,0 +1,296 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/microchip,sparx5-serdes.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Microchip Sparx5 Serdes controller
> +
> +maintainers:
> +  - Steen Hegelund <steen.hegelund@microchip.com>
> +
> +description: |
> +  The Sparx5 SERDES interfaces share the same basic functionality, but
> +  support different operating modes and line rates.
> +
> +  The following list lists the SERDES features:
> +
> +  * RX Adaptive Decision Feedback Equalizer (DFE)
> +  * Programmable continuous time linear equalizer (CTLE)
> +  * Rx variable gain control
> +  * Rx built-in fault detector (loss-of-lock/loss-of-signal)
> +  * Adjustable tx de-emphasis (FFE)
> +  * Tx output amplitude control
> +  * Supports rx eye monitor
> +  * Multiple loopback modes
> +  * Prbs generator and checker
> +  * Polarity inversion control
> +
> +  SERDES6G:
> +
> +  The SERDES6G is a high-speed SERDES interface, which can operate at
> +  the following data rates:
> +
> +  * 100 Mbps (100BASE-FX)
> +  * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX)
> +  * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX)
> +  * 5.15625 Gbps (5GBASE-KR/5G-USXGMII)
> +
> +  SERDES10G
> +
> +  The SERDES10G is a high-speed SERDES interface, which can operate at
> +  the following data rates:
> +
> +  * 100 Mbps (100BASE-FX)
> +  * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX)
> +  * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX)
> +  * 5 Gbps (QSGMII/USGMII)
> +  * 5.15625 Gbps (5GBASE-KR/5G-USXGMII)
> +  * 10 Gbps (10G-USGMII)
> +  * 10.3125 Gbps (10GBASE-R/10GBASE-KR/USXGMII)
> +
> +  SERDES25G
> +
> +  The SERDES25G is a high-speed SERDES interface, which can operate at
> +  the following data rates:
> +
> +  * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX)
> +  * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX)
> +  * 5 Gbps (QSGMII/USGMII)
> +  * 5.15625 Gbps (5GBASE-KR/5G-USXGMII)
> +  * 10 Gbps (10G-USGMII)
> +  * 10.3125 Gbps (10GBASE-R/10GBASE-KR/USXGMII)
> +  * 25.78125 Gbps (25GBASE-KR/25GBASE-CR/25GBASE-SR/25GBASE-LR/25GBASE-ER)
> +
> +properties:
> +  $nodename:
> +    pattern: "^serdes@[0-9a-f]+$"
> +
> +  compatible:
> +    const: microchip,sparx5-serdes.yaml

This has a spurious .yaml suffix ;)

> +
> +  reg:
> +    description: Address and length of the register set for the device

You don't actually have to describe this property a sit comes from the
generic schema. But maybe you could set maxItems

> +
> +  reg-names:
> +    description: |
> +      Names for each of the address spaces defined in
> +      the 'reg' property. Expects the names in the same order as the
> +      corresponding memory region in the that property.
> +

Same comment, even better, I tink you could list the expected names in
an enum or a const list

> +  '#phy-cells':
> +    const: 1
> +    description: |
> +      - The main serdes input port
> +
> +  clocks:
> +    description:
> +      A list containing the phandle to the core clock of the Sparx5 device.

You can drop the description and simply have maxItems: 1
Steen Hegelund Nov. 23, 2020, 8:11 a.m. UTC | #2
On 20.11.2020 17:09, Alexandre Belloni wrote:
>EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
>
>Hi,
>
>On 20/11/2020 16:03:56+0100, Steen Hegelund wrote:
>> Document the Sparx5 ethernet serdes phy driver bindings.
>>
>> Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
>> Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
>> ---
>>  .../bindings/phy/microchip,sparx5-serdes.yaml | 296 ++++++++++++++++++
>>  1 file changed, 296 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml b/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml
>> new file mode 100644
>> index 000000000000..0bfb752e7686
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml
>> @@ -0,0 +1,296 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/phy/microchip,sparx5-serdes.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Microchip Sparx5 Serdes controller
>> +
>> +maintainers:
>> +  - Steen Hegelund <steen.hegelund@microchip.com>
>> +
>> +description: |
>> +  The Sparx5 SERDES interfaces share the same basic functionality, but
>> +  support different operating modes and line rates.
>> +
>> +  The following list lists the SERDES features:
>> +
>> +  * RX Adaptive Decision Feedback Equalizer (DFE)
>> +  * Programmable continuous time linear equalizer (CTLE)
>> +  * Rx variable gain control
>> +  * Rx built-in fault detector (loss-of-lock/loss-of-signal)
>> +  * Adjustable tx de-emphasis (FFE)
>> +  * Tx output amplitude control
>> +  * Supports rx eye monitor
>> +  * Multiple loopback modes
>> +  * Prbs generator and checker
>> +  * Polarity inversion control
>> +
>> +  SERDES6G:
>> +
>> +  The SERDES6G is a high-speed SERDES interface, which can operate at
>> +  the following data rates:
>> +
>> +  * 100 Mbps (100BASE-FX)
>> +  * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX)
>> +  * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX)
>> +  * 5.15625 Gbps (5GBASE-KR/5G-USXGMII)
>> +
>> +  SERDES10G
>> +
>> +  The SERDES10G is a high-speed SERDES interface, which can operate at
>> +  the following data rates:
>> +
>> +  * 100 Mbps (100BASE-FX)
>> +  * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX)
>> +  * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX)
>> +  * 5 Gbps (QSGMII/USGMII)
>> +  * 5.15625 Gbps (5GBASE-KR/5G-USXGMII)
>> +  * 10 Gbps (10G-USGMII)
>> +  * 10.3125 Gbps (10GBASE-R/10GBASE-KR/USXGMII)
>> +
>> +  SERDES25G
>> +
>> +  The SERDES25G is a high-speed SERDES interface, which can operate at
>> +  the following data rates:
>> +
>> +  * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX)
>> +  * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX)
>> +  * 5 Gbps (QSGMII/USGMII)
>> +  * 5.15625 Gbps (5GBASE-KR/5G-USXGMII)
>> +  * 10 Gbps (10G-USGMII)
>> +  * 10.3125 Gbps (10GBASE-R/10GBASE-KR/USXGMII)
>> +  * 25.78125 Gbps (25GBASE-KR/25GBASE-CR/25GBASE-SR/25GBASE-LR/25GBASE-ER)
>> +
>> +properties:
>> +  $nodename:
>> +    pattern: "^serdes@[0-9a-f]+$"
>> +
>> +  compatible:
>> +    const: microchip,sparx5-serdes.yaml
>
>This has a spurious .yaml suffix ;)

I will remove that.
>
>> +
>> +  reg:
>> +    description: Address and length of the register set for the device
>
>You don't actually have to describe this property a sit comes from the
>generic schema. But maybe you could set maxItems

OK, I will remove the description.
Wouldn't minItems be better here, since there might be more targets in the
future, to support more modes?

>
>> +
>> +  reg-names:
>> +    description: |
>> +      Names for each of the address spaces defined in
>> +      the 'reg' property. Expects the names in the same order as the
>> +      corresponding memory region in the that property.
>> +
>
>Same comment, even better, I tink you could list the expected names in
>an enum or a const list

OK, it is a long list, but then it will be automatically checked.
>
>> +  '#phy-cells':
>> +    const: 1
>> +    description: |
>> +      - The main serdes input port
>> +
>> +  clocks:
>> +    description:
>> +      A list containing the phandle to the core clock of the Sparx5 device.
>
>You can drop the description and simply have maxItems: 1

OK
>
>
>--
>Alexandre Belloni, Bootlin
>Embedded Linux and Kernel engineering
>https://bootlin.com

BR
Steen

---------------------------------------
Steen Hegelund
steen.hegelund@microchip.com
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml b/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml
new file mode 100644
index 000000000000..0bfb752e7686
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml
@@ -0,0 +1,296 @@ 
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/microchip,sparx5-serdes.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip Sparx5 Serdes controller
+
+maintainers:
+  - Steen Hegelund <steen.hegelund@microchip.com>
+
+description: |
+  The Sparx5 SERDES interfaces share the same basic functionality, but
+  support different operating modes and line rates.
+
+  The following list lists the SERDES features:
+
+  * RX Adaptive Decision Feedback Equalizer (DFE)
+  * Programmable continuous time linear equalizer (CTLE)
+  * Rx variable gain control
+  * Rx built-in fault detector (loss-of-lock/loss-of-signal)
+  * Adjustable tx de-emphasis (FFE)
+  * Tx output amplitude control
+  * Supports rx eye monitor
+  * Multiple loopback modes
+  * Prbs generator and checker
+  * Polarity inversion control
+
+  SERDES6G:
+
+  The SERDES6G is a high-speed SERDES interface, which can operate at
+  the following data rates:
+
+  * 100 Mbps (100BASE-FX)
+  * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX)
+  * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX)
+  * 5.15625 Gbps (5GBASE-KR/5G-USXGMII)
+
+  SERDES10G
+
+  The SERDES10G is a high-speed SERDES interface, which can operate at
+  the following data rates:
+
+  * 100 Mbps (100BASE-FX)
+  * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX)
+  * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX)
+  * 5 Gbps (QSGMII/USGMII)
+  * 5.15625 Gbps (5GBASE-KR/5G-USXGMII)
+  * 10 Gbps (10G-USGMII)
+  * 10.3125 Gbps (10GBASE-R/10GBASE-KR/USXGMII)
+
+  SERDES25G
+
+  The SERDES25G is a high-speed SERDES interface, which can operate at
+  the following data rates:
+
+  * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX)
+  * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX)
+  * 5 Gbps (QSGMII/USGMII)
+  * 5.15625 Gbps (5GBASE-KR/5G-USXGMII)
+  * 10 Gbps (10G-USGMII)
+  * 10.3125 Gbps (10GBASE-R/10GBASE-KR/USXGMII)
+  * 25.78125 Gbps (25GBASE-KR/25GBASE-CR/25GBASE-SR/25GBASE-LR/25GBASE-ER)
+
+properties:
+  $nodename:
+    pattern: "^serdes@[0-9a-f]+$"
+
+  compatible:
+    const: microchip,sparx5-serdes.yaml
+
+  reg:
+    description: Address and length of the register set for the device
+
+  reg-names:
+    description: |
+      Names for each of the address spaces defined in
+      the 'reg' property. Expects the names in the same order as the
+      corresponding memory region in the that property.
+
+  '#phy-cells':
+    const: 1
+    description: |
+      - The main serdes input port
+
+  clocks:
+    description:
+      A list containing the phandle to the core clock of the Sparx5 device.
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - '#phy-cells'
+  - clocks
+
+additionalProperties: false
+
+examples:
+  - |
+    serdes: serdes@10808000 {
+      compatible = "microchip,sparx5-serdes";
+      #phy-cells = <1>;
+      clocks = <&sys_clk>;
+      reg = <0x10808000 0x8000>, /* sd_cmu_0 */
+        <0x10810000 0x8000>, /* sd_cmu_1 */
+        <0x10818000 0x8000>, /* sd_cmu_2 */
+        <0x10820000 0x8000>, /* sd_cmu_3 */
+        <0x10828000 0x8000>, /* sd_cmu_4 */
+        <0x10830000 0x8000>, /* sd_cmu_5 */
+        <0x10838000 0x8000>, /* sd_cmu_6 */
+        <0x10840000 0x8000>, /* sd_cmu_7 */
+        <0x10848000 0x8000>, /* sd_cmu_8 */
+        <0x10850000 0x8000>, /* sd_cmu_cfg_0 */
+        <0x10858000 0x8000>, /* sd_cmu_cfg_1 */
+        <0x10860000 0x8000>, /* sd_cmu_cfg_2 */
+        <0x10868000 0x8000>, /* sd_cmu_cfg_3 */
+        <0x10870000 0x8000>, /* sd_cmu_cfg_4 */
+        <0x10878000 0x8000>, /* sd_cmu_cfg_5 */
+        <0x10880000 0x8000>, /* sd_cmu_cfg_6 */
+        <0x10888000 0x8000>, /* sd_cmu_cfg_7 */
+        <0x10890000 0x8000>, /* sd_cmu_cfg_8 */
+        <0x10898000 0x8000>, /* sd6g_lane_0 */
+        <0x108a0000 0x8000>, /* sd6g_lane_1 */
+        <0x108a8000 0x8000>, /* sd6g_lane_2 */
+        <0x108b0000 0x8000>, /* sd6g_lane_3 */
+        <0x108b8000 0x8000>, /* sd6g_lane_4 */
+        <0x108c0000 0x8000>, /* sd6g_lane_5 */
+        <0x108c8000 0x8000>, /* sd6g_lane_6 */
+        <0x108d0000 0x8000>, /* sd6g_lane_7 */
+        <0x108d8000 0x8000>, /* sd6g_lane_8 */
+        <0x108e0000 0x8000>, /* sd6g_lane_9 */
+        <0x108e8000 0x8000>, /* sd6g_lane_10 */
+        <0x108f0000 0x8000>, /* sd6g_lane_11 */
+        <0x108f8000 0x8000>, /* sd6g_lane_12 */
+        <0x10900000 0x8000>, /* sd10g_lane_0 */
+        <0x10908000 0x8000>, /* sd10g_lane_1 */
+        <0x10910000 0x8000>, /* sd10g_lane_2 */
+        <0x10918000 0x8000>, /* sd10g_lane_3 */
+        <0x109a8000 0x8000>, /* sd_lane_0 */
+        <0x109b0000 0x8000>, /* sd_lane_1 */
+        <0x109b8000 0x8000>, /* sd_lane_2 */
+        <0x109c0000 0x8000>, /* sd_lane_3 */
+        <0x109c8000 0x8000>, /* sd_lane_4 */
+        <0x109d0000 0x8000>, /* sd_lane_5 */
+        <0x109d8000 0x8000>, /* sd_lane_6 */
+        <0x109e0000 0x8000>, /* sd_lane_7 */
+        <0x109e8000 0x8000>, /* sd_lane_8 */
+        <0x109f0000 0x8000>, /* sd_lane_9 */
+        <0x109f8000 0x8000>, /* sd_lane_10 */
+        <0x10a00000 0x8000>, /* sd_lane_11 */
+        <0x10a08000 0x8000>, /* sd_lane_12 */
+        <0x10a10000 0x8000>, /* sd_lane_13 */
+        <0x10a18000 0x8000>, /* sd_lane_14 */
+        <0x10a20000 0x8000>, /* sd_lane_15 */
+        <0x10a28000 0x8000>, /* sd_lane_16 */
+        <0x10c08000 0x8000>, /* sd_cmu_9 */
+        <0x10c10000 0x8000>, /* sd_cmu_10 */
+        <0x10c18000 0x8000>, /* sd_cmu_11 */
+        <0x10c20000 0x8000>, /* sd_cmu_12 */
+        <0x10c28000 0x8000>, /* sd_cmu_13 */
+        <0x10c30000 0x8000>, /* sd_cmu_cfg_9 */
+        <0x10c38000 0x8000>, /* sd_cmu_cfg_10 */
+        <0x10c40000 0x8000>, /* sd_cmu_cfg_11 */
+        <0x10c48000 0x8000>, /* sd_cmu_cfg_12 */
+        <0x10c50000 0x8000>, /* sd_cmu_cfg_13 */
+        <0x10c58000 0x8000>, /* sd10g_lane_4 */
+        <0x10c60000 0x8000>, /* sd10g_lane_5 */
+        <0x10c68000 0x8000>, /* sd10g_lane_6 */
+        <0x10c70000 0x8000>, /* sd10g_lane_7 */
+        <0x10c78000 0x8000>, /* sd10g_lane_8 */
+        <0x10c80000 0x8000>, /* sd10g_lane_9 */
+        <0x10c88000 0x8000>, /* sd10g_lane_10 */
+        <0x10c90000 0x8000>, /* sd10g_lane_11 */
+        <0x10c98000 0x8000>, /* sd25g_lane_0 */
+        <0x10ca0000 0x8000>, /* sd25g_lane_1 */
+        <0x10ca8000 0x8000>, /* sd25g_lane_2 */
+        <0x10cb0000 0x8000>, /* sd25g_lane_3 */
+        <0x10cb8000 0x8000>, /* sd25g_lane_4 */
+        <0x10cc0000 0x8000>, /* sd25g_lane_5 */
+        <0x10cc8000 0x8000>, /* sd25g_lane_6 */
+        <0x10cd0000 0x8000>, /* sd25g_lane_7 */
+        <0x10d58000 0x8000>, /* sd_lane_17 */
+        <0x10d60000 0x8000>, /* sd_lane_18 */
+        <0x10d68000 0x8000>, /* sd_lane_19 */
+        <0x10d70000 0x8000>, /* sd_lane_20 */
+        <0x10d78000 0x8000>, /* sd_lane_21 */
+        <0x10d80000 0x8000>, /* sd_lane_22 */
+        <0x10d88000 0x8000>, /* sd_lane_23 */
+        <0x10d90000 0x8000>, /* sd_lane_24 */
+        <0x10d98000 0x8000>, /* sd_lane_25g_25 */
+        <0x10da0000 0x8000>, /* sd_lane_25g_26 */
+        <0x10da8000 0x8000>, /* sd_lane_25g_27 */
+        <0x10db0000 0x8000>, /* sd_lane_25g_28 */
+        <0x10db8000 0x8000>, /* sd_lane_25g_29 */
+        <0x10dc0000 0x8000>, /* sd_lane_25g_30 */
+        <0x10dc8000 0x8000>, /* sd_lane_25g_31 */
+        <0x10dd0000 0x8000>; /* sd_lane_25g_32 */
+      reg-names =
+        "sd_cmu_0",
+        "sd_cmu_1",
+        "sd_cmu_2",
+        "sd_cmu_3",
+        "sd_cmu_4",
+        "sd_cmu_5",
+        "sd_cmu_6",
+        "sd_cmu_7",
+        "sd_cmu_8",
+        "sd_cmu_cfg_0",
+        "sd_cmu_cfg_1",
+        "sd_cmu_cfg_2",
+        "sd_cmu_cfg_3",
+        "sd_cmu_cfg_4",
+        "sd_cmu_cfg_5",
+        "sd_cmu_cfg_6",
+        "sd_cmu_cfg_7",
+        "sd_cmu_cfg_8",
+        "sd6g_lane_0",
+        "sd6g_lane_1",
+        "sd6g_lane_2",
+        "sd6g_lane_3",
+        "sd6g_lane_4",
+        "sd6g_lane_5",
+        "sd6g_lane_6",
+        "sd6g_lane_7",
+        "sd6g_lane_8",
+        "sd6g_lane_9",
+        "sd6g_lane_10",
+        "sd6g_lane_11",
+        "sd6g_lane_12",
+        "sd10g_lane_0",
+        "sd10g_lane_1",
+        "sd10g_lane_2",
+        "sd10g_lane_3",
+        "sd_lane_0",
+        "sd_lane_1",
+        "sd_lane_2",
+        "sd_lane_3",
+        "sd_lane_4",
+        "sd_lane_5",
+        "sd_lane_6",
+        "sd_lane_7",
+        "sd_lane_8",
+        "sd_lane_9",
+        "sd_lane_10",
+        "sd_lane_11",
+        "sd_lane_12",
+        "sd_lane_13",
+        "sd_lane_14",
+        "sd_lane_15",
+        "sd_lane_16",
+        "sd_cmu_9",
+        "sd_cmu_10",
+        "sd_cmu_11",
+        "sd_cmu_12",
+        "sd_cmu_13",
+        "sd_cmu_cfg_9",
+        "sd_cmu_cfg_10",
+        "sd_cmu_cfg_11",
+        "sd_cmu_cfg_12",
+        "sd_cmu_cfg_13",
+        "sd10g_lane_4",
+        "sd10g_lane_5",
+        "sd10g_lane_6",
+        "sd10g_lane_7",
+        "sd10g_lane_8",
+        "sd10g_lane_9",
+        "sd10g_lane_10",
+        "sd10g_lane_11",
+        "sd25g_lane_0",
+        "sd25g_lane_1",
+        "sd25g_lane_2",
+        "sd25g_lane_3",
+        "sd25g_lane_4",
+        "sd25g_lane_5",
+        "sd25g_lane_6",
+        "sd25g_lane_7",
+        "sd_lane_17",
+        "sd_lane_18",
+        "sd_lane_19",
+        "sd_lane_20",
+        "sd_lane_21",
+        "sd_lane_22",
+        "sd_lane_23",
+        "sd_lane_24",
+        "sd_lane_25g_25",
+        "sd_lane_25g_26",
+        "sd_lane_25g_27",
+        "sd_lane_25g_28",
+        "sd_lane_25g_29",
+        "sd_lane_25g_30",
+        "sd_lane_25g_31",
+        "sd_lane_25g_32";
+    };
+
+...