diff mbox series

[v3,5/6] dt-bindings: spi: Convert cadence-quadspi.txt to cadence-quadspi.yaml

Message ID 20201026094519.56083-6-vadivel.muruganx.ramuthevar@linux.intel.com
State Changes Requested
Headers show
Series spi: cadence-quadspi: Add QSPI controller support for Intel LGM SoC | expand

Checks

Context Check Description
robh/checkpatch warning total: 0 errors, 3 warnings, 148 lines checked

Commit Message

Ramuthevar, Vadivel MuruganX Oct. 26, 2020, 9:45 a.m. UTC
From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>

Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/

Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
---
 .../devicetree/bindings/spi/cadence-quadspi.txt    |  67 ----------
 .../devicetree/bindings/spi/cadence-quadspi.yaml   | 148 +++++++++++++++++++++
 2 files changed, 148 insertions(+), 67 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
 create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml

Comments

Rob Herring Oct. 26, 2020, 1:08 p.m. UTC | #1
On Mon, Oct 26, 2020 at 05:45:18PM +0800, Ramuthevar,Vadivel MuruganX wrote:
> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
> 
> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
> 
> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
> ---
>  .../devicetree/bindings/spi/cadence-quadspi.txt    |  67 ----------
>  .../devicetree/bindings/spi/cadence-quadspi.yaml   | 148 +++++++++++++++++++++
>  2 files changed, 148 insertions(+), 67 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>  create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> 
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> deleted file mode 100644
> index 945be7d5b236..000000000000
> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> +++ /dev/null
> @@ -1,67 +0,0 @@
> -* Cadence Quad SPI controller
> -
> -Required properties:
> -- compatible : should be one of the following:
> -	Generic default - "cdns,qspi-nor".
> -	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> -	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
> -- reg : Contains two entries, each of which is a tuple consisting of a
> -	physical address and length. The first entry is the address and
> -	length of the controller register set. The second entry is the
> -	address and length of the QSPI Controller data area.
> -- interrupts : Unit interrupt specifier for the controller interrupt.
> -- clocks : phandle to the Quad SPI clock.
> -- cdns,fifo-depth : Size of the data FIFO in words.
> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
> -
> -Optional properties:
> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
> -  the read data rather than the QSPI clock. Make sure that QSPI return
> -  clock is populated on the board before using this property.
> -
> -Optional subnodes:
> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
> -custom properties:
> -- cdns,read-delay : Delay for read capture logic, in clock cycles
> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
> -                  mode chip select outputs are de-asserted between
> -		  transactions.
> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
> -                  de-activated and the activation of another.
> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
> -                  transaction and deasserting the device chip select
> -		  (qspi_n_ss_out).
> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
> -                  and first bit transfer.
> -- resets	: Must contain an entry for each entry in reset-names.
> -		  See ../reset/reset.txt for details.
> -- reset-names	: Must include either "qspi" and/or "qspi-ocp".
> -
> -Example:
> -
> -	qspi: spi@ff705000 {
> -		compatible = "cdns,qspi-nor";
> -		#address-cells = <1>;
> -		#size-cells = <0>;
> -		reg = <0xff705000 0x1000>,
> -		      <0xffa00000 0x1000>;
> -		interrupts = <0 151 4>;
> -		clocks = <&qspi_clk>;
> -		cdns,is-decoded-cs;
> -		cdns,fifo-depth = <128>;
> -		cdns,fifo-width = <4>;
> -		cdns,trigger-address = <0x00000000>;
> -		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
> -		reset-names = "qspi", "qspi-ocp";
> -
> -		flash0: n25q00@0 {
> -			...
> -			cdns,read-delay = <4>;
> -			cdns,tshsl-ns = <50>;
> -			cdns,tsd2d-ns = <50>;
> -			cdns,tchsh-ns = <4>;
> -			cdns,tslch-ns = <4>;
> -		};
> -	};
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> new file mode 100644
> index 000000000000..b1b3d3ce0cc2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> @@ -0,0 +1,148 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Cadence Quad SPI controller
> +
> +maintainers:
> +  - Vadivel Murugan <vadivel.muruganx.ramuthevar@intel.com>
> +
> +allOf:
> +  - $ref: "spi-controller.yaml#"
> +
> +properties:
> +  compatible:
> +    oneOf:
> +      - items:
> +         - const: cdns,qspi-nor
> +         - const: ti,k2g-qspi, cdns,qspi-nor
> +         - const: ti,am654-ospi, cdns,qspi-nor
> +
> +  reg:
> +    items:
> +      - description: the controller register set
> +      - description: the controller data area
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  cdns,fifo-depth:
> +    description:
> +      Size of the data FIFO in words.
> +    $ref: "/schemas/types.yaml#/definitions/uint32"
> +    enum: [ 128, 256 ]
> +    default: 128
> +
> +  cdns,fifo-width:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      Bus width of the data FIFO in bytes.
> +    default: 4
> +
> +  cdns,trigger-address:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      32-bit indirect AHB trigger address.
> +
> +  cdns,is-decoded-cs:
> +    type: boolean
> +    description:
> +      Flag to indicate whether decoder is used or not.
> +
> +  cdns,rclk-en:
> +    type: boolean
> +    description:
> +      Flag to indicate that QSPI return clock is used to latch the read
> +      data rather than the QSPI clock. Make sure that QSPI return clock
> +      is populated on the board before using this property.
> +
> +  resets:
> +    maxItems : 2
> +
> +  reset-names:
> +    minItems: 1
> +    maxItems: 2
> +    items:
> +      enum: [ qspi, qspi-ocp ]
> +
> +# subnode's properties
> +patternProperties:
> +  "@[0-9a-f]+$":
> +    type: object
> +    description:
> +      flash device uses the subnodes below defined properties.
> +
> +  cdns,read-delay:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      Delay for read capture logic, in clock cycles.

As-is, these apply to the parent (controller) node. If these apply to 
the child nodes, then they need to be under 'properties' under 
'@[0-9a-f]+$'.

> +
> +  cdns,tshsl-ns:
> +    description: |

Don't need '|' if there's no formatting to preserve.

> +      Delay in nanoseconds for the length that the master mode chip select
> +      outputs are de-asserted between transactions.
> +
> +  cdns,tsd2d-ns:
> +    description: |
> +      Delay in nanoseconds between one chip select being de-activated
> +      and the activation of another.
> +
> +  cdns,tchsh-ns:
> +    description: |
> +      Delay in nanoseconds between last bit of current transaction and
> +      deasserting the device chip select (qspi_n_ss_out).
> +
> +  cdns,tslch-ns:
> +    description: |
> +      Delay in nanoseconds between setting qspi_n_ss_out low and
> +      first bit transfer.
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - cdns,fifo-depth
> +  - cdns,fifo-width
> +  - cdns,trigger-address
> +  - cdns,is-decoded-cs
> +  - cdns,rclk-en
> +  - resets
> +  - reset-names
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    qspi: spi@ff705000 {
> +      compatible = "cadence,qspi","cdns,qpsi-nor";
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +      reg = <0xff705000 0x1000>,
> +            <0xffa00000 0x1000>;
> +      interrupts = <0 151 4>;
> +      clocks = <&qspi_clk>;
> +      cdns,fifo-depth = <128>;
> +      cdns,fifo-width = <4>;
> +      cdns,trigger-address = <0x00000000>;
> +      resets = <&rst 0x1>, <&rst 0x2>;
> +      reset-names = "qspi", "qspi-ocp";
> +
> +      flash@0 {
> +              compatible = "jedec,spi-nor";
> +              reg = <0x0>;
> +              cdns,read-delay = <4>;
> +              cdns,tshsl-ns = <50>;
> +              cdns,tsd2d-ns = <50>;
> +              cdns,tchsh-ns = <4>;
> +              cdns,tslch-ns = <4>;
> +     };
> +
> +    };
> +
> +...
> -- 
> 2.11.0
>
Ramuthevar, Vadivel MuruganX Oct. 27, 2020, 3:45 a.m. UTC | #2
Hi Rob,

Thank you very much for the review comments...

On 26/10/2020 9:08 pm, Rob Herring wrote:
> On Mon, Oct 26, 2020 at 05:45:18PM +0800, Ramuthevar,Vadivel MuruganX wrote:
>> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>>
>> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
>> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
>>
>> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>> ---
>>   .../devicetree/bindings/spi/cadence-quadspi.txt    |  67 ----------
>>   .../devicetree/bindings/spi/cadence-quadspi.yaml   | 148 +++++++++++++++++++++
>>   2 files changed, 148 insertions(+), 67 deletions(-)
>>   delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>>   create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>> deleted file mode 100644
>> index 945be7d5b236..000000000000
>> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>> +++ /dev/null
>> @@ -1,67 +0,0 @@
>> -* Cadence Quad SPI controller
>> -
>> -Required properties:
>> -- compatible : should be one of the following:
>> -	Generic default - "cdns,qspi-nor".
>> -	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
>> -	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
>> -- reg : Contains two entries, each of which is a tuple consisting of a
>> -	physical address and length. The first entry is the address and
>> -	length of the controller register set. The second entry is the
>> -	address and length of the QSPI Controller data area.
>> -- interrupts : Unit interrupt specifier for the controller interrupt.
>> -- clocks : phandle to the Quad SPI clock.
>> -- cdns,fifo-depth : Size of the data FIFO in words.
>> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
>> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
>> -
>> -Optional properties:
>> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
>> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
>> -  the read data rather than the QSPI clock. Make sure that QSPI return
>> -  clock is populated on the board before using this property.
>> -
>> -Optional subnodes:
>> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
>> -custom properties:
>> -- cdns,read-delay : Delay for read capture logic, in clock cycles
>> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
>> -                  mode chip select outputs are de-asserted between
>> -		  transactions.
>> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
>> -                  de-activated and the activation of another.
>> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
>> -                  transaction and deasserting the device chip select
>> -		  (qspi_n_ss_out).
>> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
>> -                  and first bit transfer.
>> -- resets	: Must contain an entry for each entry in reset-names.
>> -		  See ../reset/reset.txt for details.
>> -- reset-names	: Must include either "qspi" and/or "qspi-ocp".
>> -
>> -Example:
>> -
>> -	qspi: spi@ff705000 {
>> -		compatible = "cdns,qspi-nor";
>> -		#address-cells = <1>;
>> -		#size-cells = <0>;
>> -		reg = <0xff705000 0x1000>,
>> -		      <0xffa00000 0x1000>;
>> -		interrupts = <0 151 4>;
>> -		clocks = <&qspi_clk>;
>> -		cdns,is-decoded-cs;
>> -		cdns,fifo-depth = <128>;
>> -		cdns,fifo-width = <4>;
>> -		cdns,trigger-address = <0x00000000>;
>> -		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
>> -		reset-names = "qspi", "qspi-ocp";
>> -
>> -		flash0: n25q00@0 {
>> -			...
>> -			cdns,read-delay = <4>;
>> -			cdns,tshsl-ns = <50>;
>> -			cdns,tsd2d-ns = <50>;
>> -			cdns,tchsh-ns = <4>;
>> -			cdns,tslch-ns = <4>;
>> -		};
>> -	};
>> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>> new file mode 100644
>> index 000000000000..b1b3d3ce0cc2
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>> @@ -0,0 +1,148 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Cadence Quad SPI controller
>> +
>> +maintainers:
>> +  - Vadivel Murugan <vadivel.muruganx.ramuthevar@intel.com>
>> +
>> +allOf:
>> +  - $ref: "spi-controller.yaml#"
>> +
>> +properties:
>> +  compatible:
>> +    oneOf:
>> +      - items:
>> +         - const: cdns,qspi-nor
>> +         - const: ti,k2g-qspi, cdns,qspi-nor
>> +         - const: ti,am654-ospi, cdns,qspi-nor
>> +
>> +  reg:
>> +    items:
>> +      - description: the controller register set
>> +      - description: the controller data area
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  cdns,fifo-depth:
>> +    description:
>> +      Size of the data FIFO in words.
>> +    $ref: "/schemas/types.yaml#/definitions/uint32"
>> +    enum: [ 128, 256 ]
>> +    default: 128
>> +
>> +  cdns,fifo-width:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      Bus width of the data FIFO in bytes.
>> +    default: 4
>> +
>> +  cdns,trigger-address:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      32-bit indirect AHB trigger address.
>> +
>> +  cdns,is-decoded-cs:
>> +    type: boolean
>> +    description:
>> +      Flag to indicate whether decoder is used or not.
>> +
>> +  cdns,rclk-en:
>> +    type: boolean
>> +    description:
>> +      Flag to indicate that QSPI return clock is used to latch the read
>> +      data rather than the QSPI clock. Make sure that QSPI return clock
>> +      is populated on the board before using this property.
>> +
>> +  resets:
>> +    maxItems : 2
>> +
>> +  reset-names:
>> +    minItems: 1
>> +    maxItems: 2
>> +    items:
>> +      enum: [ qspi, qspi-ocp ]
>> +
>> +# subnode's properties
>> +patternProperties:
>> +  "@[0-9a-f]+$":
>> +    type: object
>> +    description:
>> +      flash device uses the subnodes below defined properties.
>> +
>> +  cdns,read-delay:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      Delay for read capture logic, in clock cycles.
> 
> As-is, these apply to the parent (controller) node. If these apply to
> the child nodes, then they need to be under 'properties' under
> '@[0-9a-f]+$'.
Ok, Noted.
> 
>> +
>> +  cdns,tshsl-ns:
>> +    description: |
> 
> Don't need '|' if there's no formatting to preserve.
Noted, will update.

Regards
Vadivel
> 
>> +      Delay in nanoseconds for the length that the master mode chip select
>> +      outputs are de-asserted between transactions.
>> +
>> +  cdns,tsd2d-ns:
>> +    description: |
>> +      Delay in nanoseconds between one chip select being de-activated
>> +      and the activation of another.
>> +
>> +  cdns,tchsh-ns:
>> +    description: |
>> +      Delay in nanoseconds between last bit of current transaction and
>> +      deasserting the device chip select (qspi_n_ss_out).
>> +
>> +  cdns,tslch-ns:
>> +    description: |
>> +      Delay in nanoseconds between setting qspi_n_ss_out low and
>> +      first bit transfer.
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - interrupts
>> +  - clocks
>> +  - cdns,fifo-depth
>> +  - cdns,fifo-width
>> +  - cdns,trigger-address
>> +  - cdns,is-decoded-cs
>> +  - cdns,rclk-en
>> +  - resets
>> +  - reset-names
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> +  - |
>> +    qspi: spi@ff705000 {
>> +      compatible = "cadence,qspi","cdns,qpsi-nor";
>> +      #address-cells = <1>;
>> +      #size-cells = <0>;
>> +      reg = <0xff705000 0x1000>,
>> +            <0xffa00000 0x1000>;
>> +      interrupts = <0 151 4>;
>> +      clocks = <&qspi_clk>;
>> +      cdns,fifo-depth = <128>;
>> +      cdns,fifo-width = <4>;
>> +      cdns,trigger-address = <0x00000000>;
>> +      resets = <&rst 0x1>, <&rst 0x2>;
>> +      reset-names = "qspi", "qspi-ocp";
>> +
>> +      flash@0 {
>> +              compatible = "jedec,spi-nor";
>> +              reg = <0x0>;
>> +              cdns,read-delay = <4>;
>> +              cdns,tshsl-ns = <50>;
>> +              cdns,tsd2d-ns = <50>;
>> +              cdns,tchsh-ns = <4>;
>> +              cdns,tslch-ns = <4>;
>> +     };
>> +
>> +    };
>> +
>> +...
>> -- 
>> 2.11.0
>>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
deleted file mode 100644
index 945be7d5b236..000000000000
--- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
+++ /dev/null
@@ -1,67 +0,0 @@ 
-* Cadence Quad SPI controller
-
-Required properties:
-- compatible : should be one of the following:
-	Generic default - "cdns,qspi-nor".
-	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
-	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
-- reg : Contains two entries, each of which is a tuple consisting of a
-	physical address and length. The first entry is the address and
-	length of the controller register set. The second entry is the
-	address and length of the QSPI Controller data area.
-- interrupts : Unit interrupt specifier for the controller interrupt.
-- clocks : phandle to the Quad SPI clock.
-- cdns,fifo-depth : Size of the data FIFO in words.
-- cdns,fifo-width : Bus width of the data FIFO in bytes.
-- cdns,trigger-address : 32-bit indirect AHB trigger address.
-
-Optional properties:
-- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
-- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
-  the read data rather than the QSPI clock. Make sure that QSPI return
-  clock is populated on the board before using this property.
-
-Optional subnodes:
-Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
-custom properties:
-- cdns,read-delay : Delay for read capture logic, in clock cycles
-- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
-                  mode chip select outputs are de-asserted between
-		  transactions.
-- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
-                  de-activated and the activation of another.
-- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
-                  transaction and deasserting the device chip select
-		  (qspi_n_ss_out).
-- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
-                  and first bit transfer.
-- resets	: Must contain an entry for each entry in reset-names.
-		  See ../reset/reset.txt for details.
-- reset-names	: Must include either "qspi" and/or "qspi-ocp".
-
-Example:
-
-	qspi: spi@ff705000 {
-		compatible = "cdns,qspi-nor";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0xff705000 0x1000>,
-		      <0xffa00000 0x1000>;
-		interrupts = <0 151 4>;
-		clocks = <&qspi_clk>;
-		cdns,is-decoded-cs;
-		cdns,fifo-depth = <128>;
-		cdns,fifo-width = <4>;
-		cdns,trigger-address = <0x00000000>;
-		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
-		reset-names = "qspi", "qspi-ocp";
-
-		flash0: n25q00@0 {
-			...
-			cdns,read-delay = <4>;
-			cdns,tshsl-ns = <50>;
-			cdns,tsd2d-ns = <50>;
-			cdns,tchsh-ns = <4>;
-			cdns,tslch-ns = <4>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
new file mode 100644
index 000000000000..b1b3d3ce0cc2
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
@@ -0,0 +1,148 @@ 
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence Quad SPI controller
+
+maintainers:
+  - Vadivel Murugan <vadivel.muruganx.ramuthevar@intel.com>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+         - const: cdns,qspi-nor
+         - const: ti,k2g-qspi, cdns,qspi-nor
+         - const: ti,am654-ospi, cdns,qspi-nor
+
+  reg:
+    items:
+      - description: the controller register set
+      - description: the controller data area
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  cdns,fifo-depth:
+    description:
+      Size of the data FIFO in words.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    enum: [ 128, 256 ]
+    default: 128
+
+  cdns,fifo-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Bus width of the data FIFO in bytes.
+    default: 4
+
+  cdns,trigger-address:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      32-bit indirect AHB trigger address.
+
+  cdns,is-decoded-cs:
+    type: boolean
+    description:
+      Flag to indicate whether decoder is used or not.
+
+  cdns,rclk-en:
+    type: boolean
+    description:
+      Flag to indicate that QSPI return clock is used to latch the read
+      data rather than the QSPI clock. Make sure that QSPI return clock
+      is populated on the board before using this property.
+
+  resets:
+    maxItems : 2
+
+  reset-names:
+    minItems: 1
+    maxItems: 2
+    items:
+      enum: [ qspi, qspi-ocp ]
+
+# subnode's properties
+patternProperties:
+  "@[0-9a-f]+$":
+    type: object
+    description:
+      flash device uses the subnodes below defined properties.
+
+  cdns,read-delay:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Delay for read capture logic, in clock cycles.
+
+  cdns,tshsl-ns:
+    description: |
+      Delay in nanoseconds for the length that the master mode chip select
+      outputs are de-asserted between transactions.
+
+  cdns,tsd2d-ns:
+    description: |
+      Delay in nanoseconds between one chip select being de-activated
+      and the activation of another.
+
+  cdns,tchsh-ns:
+    description: |
+      Delay in nanoseconds between last bit of current transaction and
+      deasserting the device chip select (qspi_n_ss_out).
+
+  cdns,tslch-ns:
+    description: |
+      Delay in nanoseconds between setting qspi_n_ss_out low and
+      first bit transfer.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - cdns,fifo-depth
+  - cdns,fifo-width
+  - cdns,trigger-address
+  - cdns,is-decoded-cs
+  - cdns,rclk-en
+  - resets
+  - reset-names
+
+additionalProperties: false
+
+examples:
+  - |
+    qspi: spi@ff705000 {
+      compatible = "cadence,qspi","cdns,qpsi-nor";
+      #address-cells = <1>;
+      #size-cells = <0>;
+      reg = <0xff705000 0x1000>,
+            <0xffa00000 0x1000>;
+      interrupts = <0 151 4>;
+      clocks = <&qspi_clk>;
+      cdns,fifo-depth = <128>;
+      cdns,fifo-width = <4>;
+      cdns,trigger-address = <0x00000000>;
+      resets = <&rst 0x1>, <&rst 0x2>;
+      reset-names = "qspi", "qspi-ocp";
+
+      flash@0 {
+              compatible = "jedec,spi-nor";
+              reg = <0x0>;
+              cdns,read-delay = <4>;
+              cdns,tshsl-ns = <50>;
+              cdns,tsd2d-ns = <50>;
+              cdns,tchsh-ns = <4>;
+              cdns,tslch-ns = <4>;
+     };
+
+    };
+
+...