diff mbox series

[V3] dt-bindings: thermal: Convert i.MX to json-schema

Message ID 1589962619-28256-1-git-send-email-Anson.Huang@nxp.com
State Superseded
Headers show
Series [V3] dt-bindings: thermal: Convert i.MX to json-schema | expand

Checks

Context Check Description
robh/dt-meta-schema success
robh/checkpatch warning total: 0 errors, 2 warnings, 102 lines checked

Commit Message

Anson Huang May 20, 2020, 8:16 a.m. UTC
Convert the i.MX thermal binding to DT schema format using json-schema

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
Changes since V2:
	- remove unnecessary property in compatible;
	- add detail description for interrupts;
	- add description for each item of nvmem-cells;
	- add more detail for "fsl,tempmon" description.
---
 .../devicetree/bindings/thermal/imx-thermal.txt    |  61 ------------
 .../devicetree/bindings/thermal/imx-thermal.yaml   | 102 +++++++++++++++++++++
 2 files changed, 102 insertions(+), 61 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/thermal/imx-thermal.txt
 create mode 100644 Documentation/devicetree/bindings/thermal/imx-thermal.yaml

Comments

Aisheng Dong May 20, 2020, 9:31 a.m. UTC | #1
> From: Anson Huang <Anson.Huang@nxp.com>
> Sent: Wednesday, May 20, 2020 4:17 PM
> 
> Convert the i.MX thermal binding to DT schema format using json-schema
> 
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
> ---
> Changes since V2:
> 	- remove unnecessary property in compatible;
> 	- add detail description for interrupts;
> 	- add description for each item of nvmem-cells;
> 	- add more detail for "fsl,tempmon" description.

[...]

> +title: NXP i.MX Thermal Binding
> +
> +maintainers:
> +  - Shawn Guo <shawn.guo@linaro.org>
> +  - Anson Huang <Anson.Huang@nxp.com>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - fsl,imx6q-tempmon
> +      - fsl,imx6sx-tempmon
> +      - fsl,imx7d-tempmon
> +
> +  interrupts:
> +    description: |
> +      The interrupt output of the controller, i.MX6Q has IRQ_HIGH which
> +      will be triggered when temperature is higher than high threshold,
> +      i.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is
> IRQ_LOW
> +      and the other is IRQ_PANIC, when temperature is lower than low
> +      threshold, IRQ_LOW will be triggered, when temperature is higher
> +      than panic threshold, IRQ_PANIC will be triggered, and system can
> +      be configured to auto reboot by SRC module for IRQ_PANIC. IRQ_HIGH,
> +      IRQ_LOW and IRQ_PANIC share same interrupt output of controller.
> +    maxItems: 1
> +
> +  nvmem-cells:
> +    items:
> +      - description: Phandle to the calibration data provided by ocotp
> +      - description: Phandle to the temperature grade provided by ocotp
> +
> +  nvmem-cell-names:
> +    items:
> +      - const: calib
> +      - const: temp_grade
> +
> +  fsl,tempmon:
> +    $ref: '/schemas/types.yaml#/definitions/phandle'
> +    description: Phandle to the temperature sensor register map node.

This still looks vauge.
How about " Phandle to anatop system controller node"?

Otherwise, you can add my tag:
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>

Regards
Aisheng

> +
> +  fsl,tempmon-data:
> +    $ref: '/schemas/types.yaml#/definitions/phandle'
> +    description: |
> +      Deprecated property, phandle pointer to fuse controller that contains
> +      TEMPMON calibration data, e.g. OCOTP on imx6q. The details about
> +      calibration data can be found in SoC Reference Manual.
> +    deprecated: true
> +
> +  clocks:
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - interrupts
> +  - fsl,tempmon
> +  - nvmem-cells
> +  - nvmem-cell-names
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/imx6sx-clock.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +    efuse@21bc000 {
> +         #address-cells = <1>;
> +         #size-cells = <1>;
> +         compatible = "fsl,imx6sx-ocotp", "syscon";
> +         reg = <0x021bc000 0x4000>;
> +         clocks = <&clks IMX6SX_CLK_OCOTP>;
> +
> +         tempmon_calib: calib@38 {
> +             reg = <0x38 4>;
> +         };
> +
> +         tempmon_temp_grade: temp-grade@20 {
> +             reg = <0x20 4>;
> +         };
> +    };
> +
> +    anatop@20c8000 {
> +        compatible = "fsl,imx6q-anatop", "syscon", "simple-mfd";
> +        reg = <0x020c8000 0x1000>;
> +        interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>,
> +                     <0 54 IRQ_TYPE_LEVEL_HIGH>,
> +                     <0 127 IRQ_TYPE_LEVEL_HIGH>;
> +
> +        tempmon {
> +             compatible = "fsl,imx6sx-tempmon";
> +             interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
> +             fsl,tempmon = <&anatop>;
> +             nvmem-cells = <&tempmon_calib>,
> <&tempmon_temp_grade>;
> +             nvmem-cell-names = "calib", "temp_grade";
> +             clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
> +        };
> +    };
> --
> 2.7.4
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
deleted file mode 100644
index 823e417..0000000
--- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
+++ /dev/null
@@ -1,61 +0,0 @@ 
-* Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
-
-Required properties:
-- compatible : must be one of following:
-  - "fsl,imx6q-tempmon" for i.MX6Q,
-  - "fsl,imx6sx-tempmon" for i.MX6SX,
-  - "fsl,imx7d-tempmon" for i.MX7S/D.
-- interrupts : the interrupt output of the controller:
-  i.MX6Q has one IRQ which will be triggered when temperature is higher than high threshold,
-  i.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC,
-  when temperature is below than low threshold, IRQ_LOW will be triggered, when temperature
-  is higher than panic threshold, system will auto reboot by SRC module.
-- fsl,tempmon : phandle pointer to system controller that contains TEMPMON
-  control registers, e.g. ANATOP on imx6q.
-- nvmem-cells: A phandle to the calibration cells provided by ocotp.
-- nvmem-cell-names: Should be "calib", "temp_grade".
-
-Deprecated properties:
-- fsl,tempmon-data : phandle pointer to fuse controller that contains TEMPMON
-  calibration data, e.g. OCOTP on imx6q.  The details about calibration data
-  can be found in SoC Reference Manual.
-
-Direct access to OCOTP via fsl,tempmon-data is incorrect on some newer chips
-because it does not handle OCOTP clock requirements.
-
-Optional properties:
-- clocks : thermal sensor's clock source.
-
-Example:
-ocotp: ocotp@21bc000 {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	compatible = "fsl,imx6sx-ocotp", "syscon";
-	reg = <0x021bc000 0x4000>;
-	clocks = <&clks IMX6SX_CLK_OCOTP>;
-
-	tempmon_calib: calib@38 {
-		reg = <0x38 4>;
-	};
-
-	tempmon_temp_grade: temp-grade@20 {
-		reg = <0x20 4>;
-	};
-};
-
-tempmon: tempmon {
-	compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon";
-	interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-	fsl,tempmon = <&anatop>;
-	nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
-	nvmem-cell-names = "calib", "temp_grade";
-	clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
-};
-
-Legacy method (Deprecated):
-tempmon {
-	compatible = "fsl,imx6q-tempmon";
-	fsl,tempmon = <&anatop>;
-	fsl,tempmon-data = <&ocotp>;
-	clocks = <&clks 172>;
-};
diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.yaml b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
new file mode 100644
index 0000000..8bfd9f9
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
@@ -0,0 +1,102 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/imx-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX Thermal Binding
+
+maintainers:
+  - Shawn Guo <shawn.guo@linaro.org>
+  - Anson Huang <Anson.Huang@nxp.com>
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx6q-tempmon
+      - fsl,imx6sx-tempmon
+      - fsl,imx7d-tempmon
+
+  interrupts:
+    description: |
+      The interrupt output of the controller, i.MX6Q has IRQ_HIGH which
+      will be triggered when temperature is higher than high threshold,
+      i.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is IRQ_LOW
+      and the other is IRQ_PANIC, when temperature is lower than low
+      threshold, IRQ_LOW will be triggered, when temperature is higher
+      than panic threshold, IRQ_PANIC will be triggered, and system can
+      be configured to auto reboot by SRC module for IRQ_PANIC. IRQ_HIGH,
+      IRQ_LOW and IRQ_PANIC share same interrupt output of controller.
+    maxItems: 1
+
+  nvmem-cells:
+    items:
+      - description: Phandle to the calibration data provided by ocotp
+      - description: Phandle to the temperature grade provided by ocotp
+
+  nvmem-cell-names:
+    items:
+      - const: calib
+      - const: temp_grade
+
+  fsl,tempmon:
+    $ref: '/schemas/types.yaml#/definitions/phandle'
+    description: Phandle to the temperature sensor register map node.
+
+  fsl,tempmon-data:
+    $ref: '/schemas/types.yaml#/definitions/phandle'
+    description: |
+      Deprecated property, phandle pointer to fuse controller that contains
+      TEMPMON calibration data, e.g. OCOTP on imx6q. The details about
+      calibration data can be found in SoC Reference Manual.
+    deprecated: true
+
+  clocks:
+    maxItems: 1
+
+required:
+  - compatible
+  - interrupts
+  - fsl,tempmon
+  - nvmem-cells
+  - nvmem-cell-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx6sx-clock.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    efuse@21bc000 {
+         #address-cells = <1>;
+         #size-cells = <1>;
+         compatible = "fsl,imx6sx-ocotp", "syscon";
+         reg = <0x021bc000 0x4000>;
+         clocks = <&clks IMX6SX_CLK_OCOTP>;
+
+         tempmon_calib: calib@38 {
+             reg = <0x38 4>;
+         };
+
+         tempmon_temp_grade: temp-grade@20 {
+             reg = <0x20 4>;
+         };
+    };
+
+    anatop@20c8000 {
+        compatible = "fsl,imx6q-anatop", "syscon", "simple-mfd";
+        reg = <0x020c8000 0x1000>;
+        interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>,
+                     <0 54 IRQ_TYPE_LEVEL_HIGH>,
+                     <0 127 IRQ_TYPE_LEVEL_HIGH>;
+
+        tempmon {
+             compatible = "fsl,imx6sx-tempmon";
+             interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+             fsl,tempmon = <&anatop>;
+             nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+             nvmem-cell-names = "calib", "temp_grade";
+             clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
+        };
+    };