| Message ID | 1587536339-4030-6-git-send-email-skomatineni@nvidia.com |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
| Series | Add Tegra driver for video capture | expand |
| Context | Check | Description |
|---|---|---|
| robh/checkpatch | success |
Hi Sowjanya, Thank you for the patch. On Tue, Apr 21, 2020 at 11:18:55PM -0700, Sowjanya Komatineni wrote: > Tegra contains VI controller which can support up to 6 MIPI CSI > camera sensors. > > Each Tegra CSI port from CSI unit can be one-to-one mapper to > VI channel and can capture from an external camera sensor or > from built-in test pattern generator. > > This patch adds dt-bindings for Tegra VI and CSI. > > Acked-by: Thierry Reding <treding@nvidia.com> > Reviewed-by: Rob Herring <robh@kernel.org> > Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> > --- > .../display/tegra/nvidia,tegra20-host1x.txt | 73 ++++++++++++++++++---- > 1 file changed, 60 insertions(+), 13 deletions(-) > > diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt > index 9999255..4731921 100644 > --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt > +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt > @@ -40,14 +40,30 @@ of the following host1x client modules: > > Required properties: > - compatible: "nvidia,tegra<chip>-vi" > - - reg: Physical base address and length of the controller's registers. > + - reg: Physical base address and length of the controller registers. > - interrupts: The interrupt outputs from the controller. > - - clocks: Must contain one entry, for the module clock. > + - clocks: clocks: Must contain one entry, for the module clock. > See ../clocks/clock-bindings.txt for details. > - - resets: Must contain an entry for each entry in reset-names. > - See ../reset/reset.txt for details. > - - reset-names: Must include the following entries: > - - vi > + - Tegra20/Tegra30/Tegra114/Tegra124: > + - resets: Must contain an entry for each entry in reset-names. > + See ../reset/reset.txt for details. > + - reset-names: Must include the following entries: > + - vi > + - Tegra210: > + - power-domains: Must include venc powergate node as vi is in VE partition. > + - Tegra210 has CSI part of VI sharing same host interface and register space. > + So, VI device node should have CSI child node. > + > + - csi: mipi csi interface to vi > + > + Required properties: > + - compatible: "nvidia,tegra210-csi" > + - reg: Physical base address offset to parent and length of the controller > + registers. > + - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks. > + See ../clocks/clock-bindings.txt for details. > + - power-domains: Must include sor powergate node as csicil is in > + SOR partition. A bit of a stupid question maybe, but why is this needed ? Can't the driver that handles the vi DT node ("nvidia,tegra20-vi") handle all the registers for all the sub-blocks ? Can't we move the clocks and power domains from the CSI node to the VI node ? Regardless of the answer to this question, I think this is missing port nodes for the physical CSI-2 inputs, to connect them to sensors. I haven't seen anywhere in this series how a CSI-2 sensor is linked to the VI. > > - epp: encoder pre-processor > > @@ -309,13 +325,44 @@ Example: > reset-names = "mpe"; > }; > > - vi { > - compatible = "nvidia,tegra20-vi"; > - reg = <0x54080000 0x00040000>; > - interrupts = <0 69 0x04>; > - clocks = <&tegra_car TEGRA20_CLK_VI>; > - resets = <&tegra_car 100>; > - reset-names = "vi"; > + vi@54080000 { > + compatible = "nvidia,tegra210-vi"; > + reg = <0x0 0x54080000 0x0 0x700>; > + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; > + assigned-clocks = <&tegra_car TEGRA210_CLK_VI>; > + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>; > + > + clocks = <&tegra_car TEGRA210_CLK_VI>; > + power-domains = <&pd_venc>; > + > + #address-cells = <1>; > + #size-cells = <1>; > + > + ranges = <0x0 0x0 0x54080000 0x2000>; > + > + csi@838 { > + compatible = "nvidia,tegra210-csi"; > + reg = <0x838 0x1300>; > + assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>, > + <&tegra_car TEGRA210_CLK_CILCD>, > + <&tegra_car TEGRA210_CLK_CILE>, > + <&tegra_car TEGRA210_CLK_CSI_TPG>; > + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>, > + <&tegra_car TEGRA210_CLK_PLL_P>, > + <&tegra_car TEGRA210_CLK_PLL_P>; > + assigned-clock-rates = <102000000>, > + <102000000>, > + <102000000>, > + <972000000>; > + > + clocks = <&tegra_car TEGRA210_CLK_CSI>, > + <&tegra_car TEGRA210_CLK_CILAB>, > + <&tegra_car TEGRA210_CLK_CILCD>, > + <&tegra_car TEGRA210_CLK_CILE>, > + <&tegra_car TEGRA210_CLK_CSI_TPG>; > + clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg"; > + power-domains = <&pd_sor>; > + }; > }; > > epp {
DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=nvidia.com; s=n1; t=1587576320; bh=HfkzuR+vYVLOjA/839zIGQQg1loQfsQ+IO+/Ii0+hVQ=; h=X-PGP-Universal:Subject:To:CC:References:From:Message-ID:Date: User-Agent:MIME-Version:In-Reply-To:X-Originating-IP: X-ClientProxiedBy:Content-Type:Content-Transfer-Encoding: Content-Language; b=mXG4pQ46mtw3JTRdiTAfbKIo8ocWIwYbDoR2GlvGZNfM++w8WWv2futApPFpQPDsn DYKCKfLjQS6QMi9iado5yxDppXLzKNPSAh79WiOtZkDnxnYesOfrbPrR4NvX7uV1Mh j8yBi3WYowY2ACc/ouLfLAY4GLLXdEDKQeIi7ztdEUZlqCHH9JdQYzt55yeXTSG7Ju EdBSajJgI0RbyjAhZs9YwJ8/Sk5TpOrby6kmzk2gCzvkCYPp98U69bLnqRccI/uf4e W6Urof3IfLm6MYH3rDE3nrQmGRMu713Us4o9WX+atKkaCQ+pZUZklqfm9KrCTAdrIL Ba0krgo3iyjDQ== On 4/22/20 10:20 AM, Laurent Pinchart wrote: > External email: Use caution opening links or attachments > > > Hi Sowjanya, > > Thank you for the patch. > > On Tue, Apr 21, 2020 at 11:18:55PM -0700, Sowjanya Komatineni wrote: >> Tegra contains VI controller which can support up to 6 MIPI CSI >> camera sensors. >> >> Each Tegra CSI port from CSI unit can be one-to-one mapper to >> VI channel and can capture from an external camera sensor or >> from built-in test pattern generator. >> >> This patch adds dt-bindings for Tegra VI and CSI. >> >> Acked-by: Thierry Reding <treding@nvidia.com> >> Reviewed-by: Rob Herring <robh@kernel.org> >> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> >> --- >> .../display/tegra/nvidia,tegra20-host1x.txt | 73 ++++++++++++++++++---- >> 1 file changed, 60 insertions(+), 13 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt >> index 9999255..4731921 100644 >> --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt >> +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt >> @@ -40,14 +40,30 @@ of the following host1x client modules: >> >> Required properties: >> - compatible: "nvidia,tegra<chip>-vi" >> - - reg: Physical base address and length of the controller's registers. >> + - reg: Physical base address and length of the controller registers. >> - interrupts: The interrupt outputs from the controller. >> - - clocks: Must contain one entry, for the module clock. >> + - clocks: clocks: Must contain one entry, for the module clock. >> See ../clocks/clock-bindings.txt for details. >> - - resets: Must contain an entry for each entry in reset-names. >> - See ../reset/reset.txt for details. >> - - reset-names: Must include the following entries: >> - - vi >> + - Tegra20/Tegra30/Tegra114/Tegra124: >> + - resets: Must contain an entry for each entry in reset-names. >> + See ../reset/reset.txt for details. >> + - reset-names: Must include the following entries: >> + - vi >> + - Tegra210: >> + - power-domains: Must include venc powergate node as vi is in VE partition. >> + - Tegra210 has CSI part of VI sharing same host interface and register space. >> + So, VI device node should have CSI child node. >> + >> + - csi: mipi csi interface to vi >> + >> + Required properties: >> + - compatible: "nvidia,tegra210-csi" >> + - reg: Physical base address offset to parent and length of the controller >> + registers. >> + - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks. >> + See ../clocks/clock-bindings.txt for details. >> + - power-domains: Must include sor powergate node as csicil is in >> + SOR partition. > A bit of a stupid question maybe, but why is this needed ? Can't the > driver that handles the vi DT node ("nvidia,tegra20-vi") handle all the > registers for all the sub-blocks ? Can't we move the clocks and power > domains from the CSI node to the VI node ? CSI is separate device driver and VI is separate device driver. For T210, CSI shares register space under VI but for later Tegras its separate register space. So CSI and VI drivers are separate with their corresponding clocks and power domains in their nodes. > > Regardless of the answer to this question, I think this is missing port > nodes for the physical CSI-2 inputs, to connect them to sensors. I > haven't seen anywhere in this series how a CSI-2 sensor is linked to the > VI. This patch series is only for Tegra internal TPG and tegra video driver creates hard media links between CSI and VI, Sensor support will be in Series-2 where port nodes will be used for real sensor <-> csi <-> vi endpoints > >> - epp: encoder pre-processor >> >> @@ -309,13 +325,44 @@ Example: >> reset-names = "mpe"; >> }; >> >> - vi { >> - compatible = "nvidia,tegra20-vi"; >> - reg = <0x54080000 0x00040000>; >> - interrupts = <0 69 0x04>; >> - clocks = <&tegra_car TEGRA20_CLK_VI>; >> - resets = <&tegra_car 100>; >> - reset-names = "vi"; >> + vi@54080000 { >> + compatible = "nvidia,tegra210-vi"; >> + reg = <0x0 0x54080000 0x0 0x700>; >> + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; >> + assigned-clocks = <&tegra_car TEGRA210_CLK_VI>; >> + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>; >> + >> + clocks = <&tegra_car TEGRA210_CLK_VI>; >> + power-domains = <&pd_venc>; >> + >> + #address-cells = <1>; >> + #size-cells = <1>; >> + >> + ranges = <0x0 0x0 0x54080000 0x2000>; >> + >> + csi@838 { >> + compatible = "nvidia,tegra210-csi"; >> + reg = <0x838 0x1300>; >> + assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>, >> + <&tegra_car TEGRA210_CLK_CILCD>, >> + <&tegra_car TEGRA210_CLK_CILE>, >> + <&tegra_car TEGRA210_CLK_CSI_TPG>; >> + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>, >> + <&tegra_car TEGRA210_CLK_PLL_P>, >> + <&tegra_car TEGRA210_CLK_PLL_P>; >> + assigned-clock-rates = <102000000>, >> + <102000000>, >> + <102000000>, >> + <972000000>; >> + >> + clocks = <&tegra_car TEGRA210_CLK_CSI>, >> + <&tegra_car TEGRA210_CLK_CILAB>, >> + <&tegra_car TEGRA210_CLK_CILCD>, >> + <&tegra_car TEGRA210_CLK_CILE>, >> + <&tegra_car TEGRA210_CLK_CSI_TPG>; >> + clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg"; >> + power-domains = <&pd_sor>; >> + }; >> }; >> >> epp { > -- > Regards, > > Laurent Pinchart
Hi Sowjanya, On Wed, Apr 22, 2020 at 10:26:20AM -0700, Sowjanya Komatineni wrote: > On 4/22/20 10:20 AM, Laurent Pinchart wrote: > > On Tue, Apr 21, 2020 at 11:18:55PM -0700, Sowjanya Komatineni wrote: > >> Tegra contains VI controller which can support up to 6 MIPI CSI > >> camera sensors. > >> > >> Each Tegra CSI port from CSI unit can be one-to-one mapper to > >> VI channel and can capture from an external camera sensor or > >> from built-in test pattern generator. > >> > >> This patch adds dt-bindings for Tegra VI and CSI. > >> > >> Acked-by: Thierry Reding <treding@nvidia.com> > >> Reviewed-by: Rob Herring <robh@kernel.org> > >> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> > >> --- > >> .../display/tegra/nvidia,tegra20-host1x.txt | 73 ++++++++++++++++++---- > >> 1 file changed, 60 insertions(+), 13 deletions(-) > >> > >> diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt > >> index 9999255..4731921 100644 > >> --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt > >> +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt > >> @@ -40,14 +40,30 @@ of the following host1x client modules: > >> > >> Required properties: > >> - compatible: "nvidia,tegra<chip>-vi" > >> - - reg: Physical base address and length of the controller's registers. > >> + - reg: Physical base address and length of the controller registers. > >> - interrupts: The interrupt outputs from the controller. > >> - - clocks: Must contain one entry, for the module clock. > >> + - clocks: clocks: Must contain one entry, for the module clock. > >> See ../clocks/clock-bindings.txt for details. > >> - - resets: Must contain an entry for each entry in reset-names. > >> - See ../reset/reset.txt for details. > >> - - reset-names: Must include the following entries: > >> - - vi > >> + - Tegra20/Tegra30/Tegra114/Tegra124: > >> + - resets: Must contain an entry for each entry in reset-names. > >> + See ../reset/reset.txt for details. > >> + - reset-names: Must include the following entries: > >> + - vi > >> + - Tegra210: > >> + - power-domains: Must include venc powergate node as vi is in VE partition. > >> + - Tegra210 has CSI part of VI sharing same host interface and register space. > >> + So, VI device node should have CSI child node. > >> + > >> + - csi: mipi csi interface to vi > >> + > >> + Required properties: > >> + - compatible: "nvidia,tegra210-csi" > >> + - reg: Physical base address offset to parent and length of the controller > >> + registers. > >> + - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks. > >> + See ../clocks/clock-bindings.txt for details. > >> + - power-domains: Must include sor powergate node as csicil is in > >> + SOR partition. > > > > A bit of a stupid question maybe, but why is this needed ? Can't the > > driver that handles the vi DT node ("nvidia,tegra20-vi") handle all the > > registers for all the sub-blocks ? Can't we move the clocks and power > > domains from the CSI node to the VI node ? > > CSI is separate device driver and VI is separate device driver. That's fine, but that's a software design decision, it should not affect the DT bindings. It's possible (even if I don't necessarily recommend doing so) to create a platform device manually in the VI driver to get it bound to the CSI driver. In any case DT should describe the system architecture and shouldn't be influenced by hardware design. > For T210, CSI shares register space under VI but for later Tegras its > separate register space. This is useful information. How about interrupts though ? You don't specify any interrupt line here, how are the CSI interrutps handled ? > So CSI and VI drivers are separate with their corresponding clocks and > power domains in their nodes. > > > Regardless of the answer to this question, I think this is missing port > > nodes for the physical CSI-2 inputs, to connect them to sensors. I > > haven't seen anywhere in this series how a CSI-2 sensor is linked to the > > VI. > > This patch series is only for Tegra internal TPG and tegra video driver > creates hard media links between CSI and VI, Could you share the output of media-ctl --print-dot to show how this looks like ? > Sensor support will be in Series-2 where port nodes will be used for > real sensor <-> csi <-> vi endpoints > > >> - epp: encoder pre-processor > >> > >> @@ -309,13 +325,44 @@ Example: > >> reset-names = "mpe"; > >> }; > >> > >> - vi { > >> - compatible = "nvidia,tegra20-vi"; > >> - reg = <0x54080000 0x00040000>; > >> - interrupts = <0 69 0x04>; > >> - clocks = <&tegra_car TEGRA20_CLK_VI>; > >> - resets = <&tegra_car 100>; > >> - reset-names = "vi"; > >> + vi@54080000 { > >> + compatible = "nvidia,tegra210-vi"; > >> + reg = <0x0 0x54080000 0x0 0x700>; > >> + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; > >> + assigned-clocks = <&tegra_car TEGRA210_CLK_VI>; > >> + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>; > >> + > >> + clocks = <&tegra_car TEGRA210_CLK_VI>; > >> + power-domains = <&pd_venc>; > >> + > >> + #address-cells = <1>; > >> + #size-cells = <1>; > >> + > >> + ranges = <0x0 0x0 0x54080000 0x2000>; > >> + > >> + csi@838 { > >> + compatible = "nvidia,tegra210-csi"; > >> + reg = <0x838 0x1300>; > >> + assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>, > >> + <&tegra_car TEGRA210_CLK_CILCD>, > >> + <&tegra_car TEGRA210_CLK_CILE>, > >> + <&tegra_car TEGRA210_CLK_CSI_TPG>; > >> + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>, > >> + <&tegra_car TEGRA210_CLK_PLL_P>, > >> + <&tegra_car TEGRA210_CLK_PLL_P>; > >> + assigned-clock-rates = <102000000>, > >> + <102000000>, > >> + <102000000>, > >> + <972000000>; > >> + > >> + clocks = <&tegra_car TEGRA210_CLK_CSI>, > >> + <&tegra_car TEGRA210_CLK_CILAB>, > >> + <&tegra_car TEGRA210_CLK_CILCD>, > >> + <&tegra_car TEGRA210_CLK_CILE>, > >> + <&tegra_car TEGRA210_CLK_CSI_TPG>; > >> + clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg"; > >> + power-domains = <&pd_sor>; > >> + }; > >> }; > >> > >> epp {
On 4/22/20 10:47 AM, Laurent Pinchart wrote: > External email: Use caution opening links or attachments > > > Hi Sowjanya, > > On Wed, Apr 22, 2020 at 10:26:20AM -0700, Sowjanya Komatineni wrote: >> On 4/22/20 10:20 AM, Laurent Pinchart wrote: >>> On Tue, Apr 21, 2020 at 11:18:55PM -0700, Sowjanya Komatineni wrote: >>>> Tegra contains VI controller which can support up to 6 MIPI CSI >>>> camera sensors. >>>> >>>> Each Tegra CSI port from CSI unit can be one-to-one mapper to >>>> VI channel and can capture from an external camera sensor or >>>> from built-in test pattern generator. >>>> >>>> This patch adds dt-bindings for Tegra VI and CSI. >>>> >>>> Acked-by: Thierry Reding <treding@nvidia.com> >>>> Reviewed-by: Rob Herring <robh@kernel.org> >>>> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> >>>> --- >>>> .../display/tegra/nvidia,tegra20-host1x.txt | 73 ++++++++++++++++++---- >>>> 1 file changed, 60 insertions(+), 13 deletions(-) >>>> >>>> diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt >>>> index 9999255..4731921 100644 >>>> --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt >>>> +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt >>>> @@ -40,14 +40,30 @@ of the following host1x client modules: >>>> >>>> Required properties: >>>> - compatible: "nvidia,tegra<chip>-vi" >>>> - - reg: Physical base address and length of the controller's registers. >>>> + - reg: Physical base address and length of the controller registers. >>>> - interrupts: The interrupt outputs from the controller. >>>> - - clocks: Must contain one entry, for the module clock. >>>> + - clocks: clocks: Must contain one entry, for the module clock. >>>> See ../clocks/clock-bindings.txt for details. >>>> - - resets: Must contain an entry for each entry in reset-names. >>>> - See ../reset/reset.txt for details. >>>> - - reset-names: Must include the following entries: >>>> - - vi >>>> + - Tegra20/Tegra30/Tegra114/Tegra124: >>>> + - resets: Must contain an entry for each entry in reset-names. >>>> + See ../reset/reset.txt for details. >>>> + - reset-names: Must include the following entries: >>>> + - vi >>>> + - Tegra210: >>>> + - power-domains: Must include venc powergate node as vi is in VE partition. >>>> + - Tegra210 has CSI part of VI sharing same host interface and register space. >>>> + So, VI device node should have CSI child node. >>>> + >>>> + - csi: mipi csi interface to vi >>>> + >>>> + Required properties: >>>> + - compatible: "nvidia,tegra210-csi" >>>> + - reg: Physical base address offset to parent and length of the controller >>>> + registers. >>>> + - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks. >>>> + See ../clocks/clock-bindings.txt for details. >>>> + - power-domains: Must include sor powergate node as csicil is in >>>> + SOR partition. >>> A bit of a stupid question maybe, but why is this needed ? Can't the >>> driver that handles the vi DT node ("nvidia,tegra20-vi") handle all the >>> registers for all the sub-blocks ? Can't we move the clocks and power >>> domains from the CSI node to the VI node ? >> CSI is separate device driver and VI is separate device driver. > That's fine, but that's a software design decision, it should not affect > the DT bindings. It's possible (even if I don't necessarily recommend > doing so) to create a platform device manually in the VI driver to get > it bound to the CSI driver. In any case DT should describe the system > architecture and shouldn't be influenced by hardware design. CSI is a separate device for Tegra186 onwards and VI/CSI is common driver. DT bindings reflects the chip design. Also clocks and power domain for CSI and VI are different and CSI is separate device. > >> For T210, CSI shares register space under VI but for later Tegras its >> separate register space. > This is useful information. How about interrupts though ? You don't > specify any interrupt line here, how are the CSI interrutps handled ? All frame events are through syncpoint HW like mentioned in earlier feedbacks. This driver synchronizes capture events through host1x syncpt > >> So CSI and VI drivers are separate with their corresponding clocks and >> power domains in their nodes. >> >>> Regardless of the answer to this question, I think this is missing port >>> nodes for the physical CSI-2 inputs, to connect them to sensors. I >>> haven't seen anywhere in this series how a CSI-2 sensor is linked to the >>> VI. >> This patch series is only for Tegra internal TPG and tegra video driver >> creates hard media links between CSI and VI, > Could you share the output of media-ctl --print-dot to show how this > looks like ? digraph board { rankdir=TB n00000001 [label="{{} | tpg-0\n | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green] n00000001:port0 -> n00000003 n00000003 [label="54080000.vi-output-0\n/dev/video0", shape=box, style=filled, fillcolor=yellow] n00000009 [label="{{} | tpg-1\n | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green] n00000009:port0 -> n0000000b n0000000b [label="54080000.vi-output-1\n/dev/video1", shape=box, style=filled, fillcolor=yellow] n00000011 [label="{{} | tpg-2\n | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green] n00000011:port0 -> n00000013 n00000013 [label="54080000.vi-output-2\n/dev/video2", shape=box, style=filled, fillcolor=yellow] n00000019 [label="{{} | tpg-3\n | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green] n00000019:port0 -> n0000001b n0000001b [label="54080000.vi-output-3\n/dev/video3", shape=box, style=filled, fillcolor=yellow] n00000021 [label="{{} | tpg-4\n | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green] n00000021:port0 -> n00000023 n00000023 [label="54080000.vi-output-4\n/dev/video4", shape=box, style=filled, fillcolor=yellow] n00000029 [label="{{} | tpg-5\n | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green] n00000029:port0 -> n0000002b n0000002b [label="54080000.vi-output-5\n/dev/video5", shape=box, style=filled, fillcolor=yellow] } > >> Sensor support will be in Series-2 where port nodes will be used for >> real sensor <-> csi <-> vi endpoints >> >>>> - epp: encoder pre-processor >>>> >>>> @@ -309,13 +325,44 @@ Example: >>>> reset-names = "mpe"; >>>> }; >>>> >>>> - vi { >>>> - compatible = "nvidia,tegra20-vi"; >>>> - reg = <0x54080000 0x00040000>; >>>> - interrupts = <0 69 0x04>; >>>> - clocks = <&tegra_car TEGRA20_CLK_VI>; >>>> - resets = <&tegra_car 100>; >>>> - reset-names = "vi"; >>>> + vi@54080000 { >>>> + compatible = "nvidia,tegra210-vi"; >>>> + reg = <0x0 0x54080000 0x0 0x700>; >>>> + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; >>>> + assigned-clocks = <&tegra_car TEGRA210_CLK_VI>; >>>> + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>; >>>> + >>>> + clocks = <&tegra_car TEGRA210_CLK_VI>; >>>> + power-domains = <&pd_venc>; >>>> + >>>> + #address-cells = <1>; >>>> + #size-cells = <1>; >>>> + >>>> + ranges = <0x0 0x0 0x54080000 0x2000>; >>>> + >>>> + csi@838 { >>>> + compatible = "nvidia,tegra210-csi"; >>>> + reg = <0x838 0x1300>; >>>> + assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>, >>>> + <&tegra_car TEGRA210_CLK_CILCD>, >>>> + <&tegra_car TEGRA210_CLK_CILE>, >>>> + <&tegra_car TEGRA210_CLK_CSI_TPG>; >>>> + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>, >>>> + <&tegra_car TEGRA210_CLK_PLL_P>, >>>> + <&tegra_car TEGRA210_CLK_PLL_P>; >>>> + assigned-clock-rates = <102000000>, >>>> + <102000000>, >>>> + <102000000>, >>>> + <972000000>; >>>> + >>>> + clocks = <&tegra_car TEGRA210_CLK_CSI>, >>>> + <&tegra_car TEGRA210_CLK_CILAB>, >>>> + <&tegra_car TEGRA210_CLK_CILCD>, >>>> + <&tegra_car TEGRA210_CLK_CILE>, >>>> + <&tegra_car TEGRA210_CLK_CSI_TPG>; >>>> + clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg"; >>>> + power-domains = <&pd_sor>; >>>> + }; >>>> }; >>>> >>>> epp { > -- > Regards, > > Laurent Pinchart
diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index 9999255..4731921 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -40,14 +40,30 @@ of the following host1x client modules: Required properties: - compatible: "nvidia,tegra<chip>-vi" - - reg: Physical base address and length of the controller's registers. + - reg: Physical base address and length of the controller registers. - interrupts: The interrupt outputs from the controller. - - clocks: Must contain one entry, for the module clock. + - clocks: clocks: Must contain one entry, for the module clock. See ../clocks/clock-bindings.txt for details. - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - vi + - Tegra20/Tegra30/Tegra114/Tegra124: + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - vi + - Tegra210: + - power-domains: Must include venc powergate node as vi is in VE partition. + - Tegra210 has CSI part of VI sharing same host interface and register space. + So, VI device node should have CSI child node. + + - csi: mipi csi interface to vi + + Required properties: + - compatible: "nvidia,tegra210-csi" + - reg: Physical base address offset to parent and length of the controller + registers. + - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks. + See ../clocks/clock-bindings.txt for details. + - power-domains: Must include sor powergate node as csicil is in + SOR partition. - epp: encoder pre-processor @@ -309,13 +325,44 @@ Example: reset-names = "mpe"; }; - vi { - compatible = "nvidia,tegra20-vi"; - reg = <0x54080000 0x00040000>; - interrupts = <0 69 0x04>; - clocks = <&tegra_car TEGRA20_CLK_VI>; - resets = <&tegra_car 100>; - reset-names = "vi"; + vi@54080000 { + compatible = "nvidia,tegra210-vi"; + reg = <0x0 0x54080000 0x0 0x700>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + assigned-clocks = <&tegra_car TEGRA210_CLK_VI>; + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>; + + clocks = <&tegra_car TEGRA210_CLK_VI>; + power-domains = <&pd_venc>; + + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0x0 0x0 0x54080000 0x2000>; + + csi@838 { + compatible = "nvidia,tegra210-csi"; + reg = <0x838 0x1300>; + assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>, + <&tegra_car TEGRA210_CLK_CILCD>, + <&tegra_car TEGRA210_CLK_CILE>, + <&tegra_car TEGRA210_CLK_CSI_TPG>; + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>, + <&tegra_car TEGRA210_CLK_PLL_P>, + <&tegra_car TEGRA210_CLK_PLL_P>; + assigned-clock-rates = <102000000>, + <102000000>, + <102000000>, + <972000000>; + + clocks = <&tegra_car TEGRA210_CLK_CSI>, + <&tegra_car TEGRA210_CLK_CILAB>, + <&tegra_car TEGRA210_CLK_CILCD>, + <&tegra_car TEGRA210_CLK_CILE>, + <&tegra_car TEGRA210_CLK_CSI_TPG>; + clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg"; + power-domains = <&pd_sor>; + }; }; epp {