[1/8] dt-bindings: mfd: document stpmu1 pmic

From: pascal paillet <p.paillet@st.com>

stpmu1 is a pmic from STMicroelectronics. The stpmu1 integrates 10
regulators and 3 switches with various capabilities.

Signed-off-by: pascal paillet <p.paillet@st.com>
---
 .../devicetree/bindings/mfd/st,stpmu1.txt          | 138 +++++++++++++++++++++
 1 file changed, 138 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/st,stpmu1.txt

On Thu, Jul 05, 2018 at 03:14:22PM +0000, Pascal PAILLET-LME wrote:
> From: pascal paillet <p.paillet@st.com>
> 
> stpmu1 is a pmic from STMicroelectronics. The stpmu1 integrates 10
> regulators and 3 switches with various capabilities.
> 
> Signed-off-by: pascal paillet <p.paillet@st.com>
> ---
>  .../devicetree/bindings/mfd/st,stpmu1.txt          | 138 +++++++++++++++++++++
>  1 file changed, 138 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/st,stpmu1.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/st,stpmu1.txt b/Documentation/devicetree/bindings/mfd/st,stpmu1.txt
> new file mode 100644
> index 0000000..53bdab4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/st,stpmu1.txt
> @@ -0,0 +1,138 @@
> +* STMicroelectronics STPMU1 Power Management IC
> +
> +Required parent device properties:
> +- compatible: "st,stpmu1"
> +- reg: the I2C slave address for the stpmu1 chip
> +- interrupts-extended: interrupt lines to use: second irq is for wakeup.
> +- #interrupt-cells: should be 2.
> +- interrupt-controller: describes the STPMU1 as an interrupt
> +  controller (has its own domain). interrupt number are the following:
> +	/* Interrupt Register 1 (0x50 for latch) */
> +	IT_SWOUT_R=0
> +	IT_SWOUT_F=1
> +	IT_VBUS_OTG_R=2
> +	IT_VBUS_OTG_F=3
> +	IT_WAKEUP_R=4
> +	IT_WAKEUP_F=5
> +	IT_PONKEY_R=6
> +	IT_PONKEY_F=7
> +	/* Interrupt Register 2 (0x51 for latch) */
> +	IT_OVP_BOOST=8
> +	IT_OCP_BOOST=9
> +	IT_OCP_SWOUT=10
> +	IT_OCP_OTG=11
> +	IT_CURLIM_BUCK4=12
> +	IT_CURLIM_BUCK3=13
> +	IT_CURLIM_BUCK2=14
> +	IT_CURLIM_BUCK1=15
> +	/* Interrupt Register 3 (0x52 for latch) */
> +	IT_SHORT_SWOUT=16
> +	IT_SHORT_SWOTG=17
> +	IT_CURLIM_LDO6=18
> +	IT_CURLIM_LDO5=19
> +	IT_CURLIM_LDO4=20
> +	IT_CURLIM_LDO3=21
> +	IT_CURLIM_LDO2=22
> +	IT_CURLIM_LDO1=23
> +	/* Interrupt Register 3 (0x52 for latch) */
> +	IT_SWIN_R=24
> +	IT_SWIN_F=25
> +	IT_RESERVED_1=26
> +	IT_RESERVED_2=27
> +	IT_VINLOW_R=28
> +	IT_VINLOW_F=29
> +	IT_TWARN_R=30
> +	IT_TWARN_F=31
> +
> +Optional parent device properties:
> +- st,main_control_register:

s/_/-/

And elsewhere...

> +	-bit 1: Power cycling will be performed on turn OFF condition
> +	-bit 2: PWRCTRL is functional
> +	-bit 3: PWRCTRL active high
> +- st,pads_pull_register:
> +	-bit 1: WAKEUP pull down is not active
> +	-bit 2: PWRCTRL pull up is active
> +	-bit 3: PWRCTRL pull down is active
> +	-bit 4: WAKEUP detector is disabled
> +- st,vin_control_register:
> +	-bit 0: VINLOW monitoring is enabled
> +	-bit [1...3]: VINLOW rising threshold
> +		000 VINOK_f + 50mV
> +		001 VINOK_f + 100mV
> +		010 VINOK_f + 150mV
> +		011 VINOK_f + 200mV
> +		100 VINOK_f + 250mV
> +		101 VINOK_f + 300mV
> +		110 VINOK_f + 350mV
> +		111 VINOK_f + 400mV
> +	-bit [4...5]: VINLOW hyst
> +		00 100mV
> +		01 200mV
> +		10 300mV
> +		11 400mV
> +	-bit 6: SW_OUT detector is disabled
> +	-bit 7: SW_IN detector is enabled.
> +- st,usb_control_register:
> +	-bit 3: SW_OUT current limit
> +		0: 600mA
> +		1: 1.1A
> +	-bit 4: VBUS_OTG discharge is enabled
> +	-bit 5: SW_OUT discharge is enabled
> +	-bit 6: VBUS_OTG detection is enabled
> +	-bit 7: BOOST_OVP is disabled

Just dumping register values into DT is not the greatest design.

> +
> +
> +stpmu1 consists is a varied group of sub-devices:
> +
> +Device			 Description
> +------			------------
> +stpmu1-onkey		: On key
> +stpmu1-regulators	: Regulators
> +stpmu1-wdt		: Watchdog

These should match the node name below.

> +
> +each sub-device bindings is be described in associated driver
> +documentation section.
> +
> +Example:
> +
> +pmic: stpmu1@33 {
> +	compatible = "st,stpmu1";
> +	reg = <0x33>;
> +	interrupts = <0 2>;
> +	interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_NONE>,
> +			      <&exti 55 1>;
> +	st,version_status = <0x10>;
> +	st,main_control_register=<0x0c>;
> +	interrupt-controller;
> +	#interrupt-cells = <2>;
> +	onkey {
> +		compatible = "st,stpmu1-onkey";
> +		interrupt-parent = <&pmic>;
> +		interrupts = <7 0>,<6 1>;

> +		st,onkey-pwroff-enabled;
> +		st,onkey-press-seconds = <10>;

IIRC, we have some standard properties for these.

> +	};
> +
> +	watchdog {
> +		compatible = "st,stpmu1-wdt";
> +	};
> +
> +	regulators {
> +		compatible = "st,stpmu1-regulators";
> +
> +		vdd_core: regulator@0 {

unit-address without reg is not valid. regulator-buck1, etc. instead.

> +			regulator-compatible = "buck1";
> +			regulator-name = "vdd_core";
> +			regulator-boot-on;
> +			regulator-min-microvolt = <700000>;
> +			regulator-max-microvolt = <1200000>;
> +		};
> +		vdd: regulator@1 {
> +			regulator-compatible = "buck3";
> +			regulator-name = "vdd";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-boot-on;
> +			regulator-pull-down;
> +		};
> +	};
> -- 
> 1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html