[net] net: mvneta: Don't advertise 2.5G modes

Message ID 20181109081733.24458-1-maxime.chevallier@bootlin.com
State Under Review
Delegated to: David Miller
Headers show
Series
  • [net] net: mvneta: Don't advertise 2.5G modes
Related show

Commit Message

Maxime Chevallier Nov. 9, 2018, 8:17 a.m.
Using 2.5G speed relies on the SerDes lanes being configured
accordingly. The lanes have to be reconfigured to switch between
1G and 2.5G, and for now only the bootloader does this configuration.

In the case we add a Comphy driver to handle switching the lanes
dynamically, it's better for now to stick with supporting only 1G and
add advertisement for 2.5G once we really are capable of handling both
speeds without problem.

Since the interface mode is initialy taken from the DT, we want to make
sure that adding comphy support won't break boards that don't update
their dtb.

Fixes: da58a931f248 ("net: mvneta: Add support for 2500Mbps SGMII")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/ethernet/marvell/mvneta.c | 12 +++---------
 1 file changed, 3 insertions(+), 9 deletions(-)

Comments

Russell King - ARM Linux Nov. 9, 2018, 9:57 a.m. | #1
On Fri, Nov 09, 2018 at 09:17:33AM +0100, Maxime Chevallier wrote:
> Using 2.5G speed relies on the SerDes lanes being configured
> accordingly. The lanes have to be reconfigured to switch between
> 1G and 2.5G, and for now only the bootloader does this configuration.
> 
> In the case we add a Comphy driver to handle switching the lanes
> dynamically, it's better for now to stick with supporting only 1G and
> add advertisement for 2.5G once we really are capable of handling both
> speeds without problem.
> 
> Since the interface mode is initialy taken from the DT, we want to make
> sure that adding comphy support won't break boards that don't update
> their dtb.
> 
> Fixes: da58a931f248 ("net: mvneta: Add support for 2500Mbps SGMII")
> Reported-by: Andrew Lunn <andrew@lunn.ch>
> Reported-by: Russell King <linux@armlinux.org.uk>
> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>

As we discussed on IRC... however, please can we wait until Monday/
Tuesday before merging this patch to allow for some further thought
and discussion - by which time I expect to have a comphy driver.

Thanks.

> ---
>  drivers/net/ethernet/marvell/mvneta.c | 12 +++---------
>  1 file changed, 3 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
> index 5bfd349bf41a..c19ecd153499 100644
> --- a/drivers/net/ethernet/marvell/mvneta.c
> +++ b/drivers/net/ethernet/marvell/mvneta.c
> @@ -3343,7 +3343,6 @@ static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
>  	if (state->interface != PHY_INTERFACE_MODE_NA &&
>  	    state->interface != PHY_INTERFACE_MODE_QSGMII &&
>  	    state->interface != PHY_INTERFACE_MODE_SGMII &&
> -	    state->interface != PHY_INTERFACE_MODE_2500BASEX &&
>  	    !phy_interface_mode_is_8023z(state->interface) &&
>  	    !phy_interface_mode_is_rgmii(state->interface)) {
>  		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> @@ -3357,14 +3356,9 @@ static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
>  	/* Asymmetric pause is unsupported */
>  	phylink_set(mask, Pause);
>  
> -	/* We cannot use 1Gbps when using the 2.5G interface. */
> -	if (state->interface == PHY_INTERFACE_MODE_2500BASEX) {
> -		phylink_set(mask, 2500baseT_Full);
> -		phylink_set(mask, 2500baseX_Full);
> -	} else {
> -		phylink_set(mask, 1000baseT_Full);
> -		phylink_set(mask, 1000baseX_Full);
> -	}
> +	/* Half-duplex at speeds higher than 100Mbit is unsupported */
> +	phylink_set(mask, 1000baseT_Full);
> +	phylink_set(mask, 1000baseX_Full);
>  
>  	if (!phy_interface_mode_is_8023z(state->interface)) {
>  		/* 10M and 100M are only supported in non-802.3z mode */
> -- 
> 2.11.0
>

Patch

diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 5bfd349bf41a..c19ecd153499 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -3343,7 +3343,6 @@  static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
 	if (state->interface != PHY_INTERFACE_MODE_NA &&
 	    state->interface != PHY_INTERFACE_MODE_QSGMII &&
 	    state->interface != PHY_INTERFACE_MODE_SGMII &&
-	    state->interface != PHY_INTERFACE_MODE_2500BASEX &&
 	    !phy_interface_mode_is_8023z(state->interface) &&
 	    !phy_interface_mode_is_rgmii(state->interface)) {
 		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
@@ -3357,14 +3356,9 @@  static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
 	/* Asymmetric pause is unsupported */
 	phylink_set(mask, Pause);
 
-	/* We cannot use 1Gbps when using the 2.5G interface. */
-	if (state->interface == PHY_INTERFACE_MODE_2500BASEX) {
-		phylink_set(mask, 2500baseT_Full);
-		phylink_set(mask, 2500baseX_Full);
-	} else {
-		phylink_set(mask, 1000baseT_Full);
-		phylink_set(mask, 1000baseX_Full);
-	}
+	/* Half-duplex at speeds higher than 100Mbit is unsupported */
+	phylink_set(mask, 1000baseT_Full);
+	phylink_set(mask, 1000baseX_Full);
 
 	if (!phy_interface_mode_is_8023z(state->interface)) {
 		/* 10M and 100M are only supported in non-802.3z mode */