[linux,dev-4.18] net: phy: Allow BCM54616S PHY to setup internal TX/RX clock delay

Message ID 20181106195233.811297-1-taoren@fb.com
State Not Applicable, archived
Headers show
Series
  • [linux,dev-4.18] net: phy: Allow BCM54616S PHY to setup internal TX/RX clock delay
Related show

Commit Message

Tao Ren Nov. 6, 2018, 7:52 p.m.
This patch allows users to enable/disable internal TX and/or RX clock
delay for BCM54616S PHYs so as to satisfy RGMII timing specifications.

On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.

The patch is inspired by commit 733336262b28 ("net: phy: Allow BCM5481x
PHYs to setup internal TX/RX clock delay").

Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/phy/broadcom.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

Patch

diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index e86ea105c802..704537010453 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -92,7 +92,7 @@  static int bcm54612e_config_init(struct phy_device *phydev)
 	return 0;
 }
 
-static int bcm5481x_config(struct phy_device *phydev)
+static int bcm54xx_config_clock_delay(struct phy_device *phydev)
 {
 	int rc, val;
 
@@ -429,7 +429,7 @@  static int bcm5481_config_aneg(struct phy_device *phydev)
 	ret = genphy_config_aneg(phydev);
 
 	/* Then we can set up the delay. */
-	bcm5481x_config(phydev);
+	bcm54xx_config_clock_delay(phydev);
 
 	if (of_property_read_bool(np, "enet-phy-lane-swap")) {
 		/* Lane Swap - Undocumented register...magic! */
@@ -442,6 +442,19 @@  static int bcm5481_config_aneg(struct phy_device *phydev)
 	return ret;
 }
 
+static int bcm54616s_config_aneg(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Aneg firsly. */
+	ret = genphy_config_aneg(phydev);
+
+	/* Then we can set up the delay. */
+	bcm54xx_config_clock_delay(phydev);
+
+	return ret;
+}
+
 static int brcm_phy_setbits(struct phy_device *phydev, int reg, int set)
 {
 	int val;
@@ -636,6 +649,7 @@  static struct phy_driver broadcom_drivers[] = {
 	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
+	.config_aneg	= bcm54616s_config_aneg,
 	.ack_interrupt	= bcm_phy_ack_intr,
 	.config_intr	= bcm_phy_config_intr,
 }, {