Message ID | 20181029175243.13453-2-jacob.e.keller@intel.com |
---|---|
State | Accepted |
Delegated to: | Jeff Kirsher |
Headers | show |
Series | [net,1/2] i40e: restore NETIF_F_GSO_IPXIP[46] to netdev features | expand |
> -----Original Message----- > From: Intel-wired-lan [mailto:intel-wired-lan-bounces@osuosl.org] On > Behalf Of Jacob Keller > Sent: Monday, October 29, 2018 10:53 AM > To: Intel Wired LAN <intel-wired-lan@lists.osuosl.org> > Subject: [Intel-wired-lan] [net 2/2] i40e: enable NETIF_F_NTUPLE and > NETIF_F_HW_TC at driver load > > The assignment of the feature flag NETIF_F_NTUPLE and NETIF_F_HW_TC > occurs prior to the initial setup of the local hw_features variable. > > This means the features are set as user-changeable, but are not set in the > currently active feature list. This results in the features being disabled at the > driver's initial load. > > Move the assignment after the initial assignment of hw_features, and assign > to the local variable. This ensures that NETIF_F_NTUPLE and NETIF_F_HW_TC > are marked as user-changeable, and also enables them by default when the > driver loads. > > Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> > --- > drivers/net/ethernet/intel/i40e/i40e_main.c | 6 +++--- > 1 file changed, 3 insertions(+), 3 deletions(-) Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c index 3ff5ee49818b..21c2688d6308 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_main.c +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c @@ -12268,13 +12268,13 @@ static int i40e_config_netdev(struct i40e_vsi *vsi) /* record features VLANs can make use of */ netdev->vlan_features |= hw_enc_features | NETIF_F_TSO_MANGLEID; - if (!(pf->flags & I40E_FLAG_MFP_ENABLED)) - netdev->hw_features |= NETIF_F_NTUPLE | NETIF_F_HW_TC; - hw_features = hw_enc_features | NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX; + if (!(pf->flags & I40E_FLAG_MFP_ENABLED)) + hw_features |= NETIF_F_NTUPLE | NETIF_F_HW_TC; + netdev->hw_features |= hw_features; netdev->features |= hw_features | NETIF_F_HW_VLAN_CTAG_FILTER;
The assignment of the feature flag NETIF_F_NTUPLE and NETIF_F_HW_TC occurs prior to the initial setup of the local hw_features variable. This means the features are set as user-changeable, but are not set in the currently active feature list. This results in the features being disabled at the driver's initial load. Move the assignment after the initial assignment of hw_features, and assign to the local variable. This ensures that NETIF_F_NTUPLE and NETIF_F_HW_TC are marked as user-changeable, and also enables them by default when the driver loads. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> --- drivers/net/ethernet/intel/i40e/i40e_main.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)