diff --git a/MAINTAINERS b/MAINTAINERS index e2c48a8..71a1310 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -17,6 +17,10 @@ # Board CPU # ######################################################################### +Haiying Wang + + P1021MDS P1021 + Poonam Aggrwal P2020RDB P2020 diff --git a/README b/README index 8779544..cd785c5 100644 --- a/README +++ b/README @@ -2225,6 +2225,19 @@ FIT uImage format: Adds the MTD partitioning infrastructure from the Linux kernel. Needed for UBI support. +- NAND Boot Support + CONFIG_NAND_U_BOOT + + Builds a U-Boot image that boots from NAND, prefixed by a small + loader stub (secondary program loader -- SPL) that loads the + rest of U-Boot into RAM. This symbol will be set in all build + phases. + + CONFIG_NAND_SPL + + This is set by the build system when compiling code to go into + the SPL. It is not set when building the code that the SPL + loads. Modem Support: -------------- diff --git a/board/freescale/p1021mds/Makefile b/board/freescale/p1021mds/Makefile new file mode 100644 index 0000000..50d4743 --- /dev/null +++ b/board/freescale/p1021mds/Makefile @@ -0,0 +1,52 @@ +# +# Copyright (C) 2010-2011 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += law.o +COBJS-y += tlb.o +COBJS-y += ddr.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS-y)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/p1021mds/ddr.c b/board/freescale/p1021mds/ddr.c new file mode 100644 index 0000000..19a2072 --- /dev/null +++ b/board/freescale/p1021mds/ddr.c @@ -0,0 +1,81 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + /* + * Factors to consider for clock adjust: + */ + popts->clk_adjust = 6; + + /* + * Factors to consider for CPO: + */ + popts->cpo_override = 0x1f; + + /* + * Factors to consider for write data delay: + */ + popts->write_data_delay = 2; + + /* + * Factors to consider for half-strength driver enable: + */ + popts->half_strength_driver_enable = 1; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 1; + popts->rtt_override_value = DDR3_RTT_40_OHM; /* 40 Ohm rtt */ + popts->rtt_wr_override_value = 2; /* Rtt_WR */ + + /* Write leveling override */ + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xa; + popts->wrlvl_start = 0x8; + /* + * P1021 supports max 32-bit DDR width + */ + popts->data_bus_width = 1; + + /* + * disable on-the-fly burst chop mode for 32 bit data bus + */ + popts->OTF_burst_chop_en = 0; + + /* + * Set fixed 8 beat burst for 32 bit data bus + */ + popts->burst_length = DDR_BL8; +} diff --git a/board/freescale/p1021mds/law.c b/board/freescale/p1021mds/law.c new file mode 100644 index 0000000..8e5e305 --- /dev/null +++ b/board/freescale/p1021mds/law.c @@ -0,0 +1,32 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_256K, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1021mds/p1021mds.c b/board/freescale/p1021mds/p1021mds.c new file mode 100644 index 0000000..f6dccc0 --- /dev/null +++ b/board/freescale/p1021mds/p1021mds.c @@ -0,0 +1,181 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#ifdef CONFIG_QE +const qe_iop_conf_t qe_iop_conf_tab[] = { + /* QE_MUX_MDC */ + {1, 19, 1, 0, 1}, /* QE_MUX_MDC */ + /* QE_MUX_MDIO */ + {1, 20, 3, 0, 1}, /* QE_MUX_MDIO */ + + /* UCC_1_MII */ + {0, 23, 2, 0, 2}, /* CLK12 */ + {0, 24, 2, 0, 1}, /* CLK9 */ + {0, 7, 1, 0, 2}, /* ENET1_TXD0_SER1_TXD0 */ + {0, 9, 1, 0, 2}, /* ENET1_TXD1_SER1_TXD1 */ + {0, 11, 1, 0, 2}, /* ENET1_TXD2_SER1_TXD2 */ + {0, 12, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3 */ + {0, 6, 2, 0, 2}, /* ENET1_RXD0_SER1_RXD0 */ + {0, 10, 2, 0, 2}, /* ENET1_RXD1_SER1_RXD1 */ + {0, 14, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2 */ + {0, 15, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3 */ + {0, 5, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */ + {0, 13, 1, 0, 2}, /* ENET1_TX_ER */ + {0, 4, 2, 0, 2}, /* ENET1_RX_DV_SER1_CTS_B */ + {0, 8, 2, 0, 2}, /* ENET1_RX_ER_SER1_CD_B */ + {0, 17, 2, 0, 2}, /* ENET1_CRS */ + {0, 16, 2, 0, 2}, /* ENET1_COL */ + + /* UCC_5_RMII */ + {1, 11, 2, 0, 1}, /* CLK13 */ + {1, 7, 1, 0, 2}, /* ENET5_TXD0_SER5_TXD0 */ + {1, 10, 1, 0, 2}, /* ENET5_TXD1_SER5_TXD1 */ + {1, 6, 2, 0, 2}, /* ENET5_RXD0_SER5_RXD0 */ + {1, 9, 2, 0, 2}, /* ENET5_RXD1_SER5_RXD1 */ + {1, 5, 1, 0, 2}, /* ENET5_TX_EN_SER5_RTS_B */ + {1, 4, 2, 0, 2}, /* ENET5_RX_DV_SER5_CTS_B */ + {1, 8, 2, 0, 2}, /* ENET5_RX_ER_SER5_CD_B */ + + {0, 0, 0, 0, QE_IOP_TAB_END} /* END of table */ +}; +#endif + +int board_early_init_f(void) +{ + + fsl_lbc_t *lbc = LBC_BASE_ADDR; + +#ifdef CONFIG_MMC + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + setbits_be32(&gur->pmuxcr, + (MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP)); +#endif + + /* Set ABSWP to implement conversion of addresses in the LBC */ + setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR); + + return 0; +} + +int checkboard(void) +{ + printf("Board: P1021 MDS\n"); + + return 0; +} + +#ifdef CONFIG_PCI +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} +#endif + +#ifdef CONFIG_TSEC_ENET +int board_eth_init(bd_t *bis) +{ + struct fsl_pq_mdio_info mdio_info; + struct tsec_info_struct tsec_info[3]; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + int num = 0; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + num++; +#endif + +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + num++; +#endif + +#ifdef CONFIG_TSEC3 + SET_STD_TSEC_INFO(tsec_info[num], 3); + if (!(in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_SGMII3_DIS)) + tsec_info[num].flags |= TSEC_SGMII; + num++; +#endif + + if (!num) { + printf("No TSECs initialized\n"); + return 0; + } + + mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + mdio_info.name = DEFAULT_MII_NAME; + + fsl_pq_mdio_init(bis, &mdio_info); + + tsec_eth_init(bis, tsec_info, num); + +#if defined(CONFIG_UEC_ETH) + /* QE0 and QE3 need to be exposed for UCC1 and UCC5 Eth mode */ + setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE0); + setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE3); + + uec_standard_init(bis); +#endif + + return pci_eth_init(bis); +} +#endif + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, base, size); + + FT_FSL_PCI_SETUP; + +#ifdef CONFIG_QE + do_fixup_by_compat(blob, "fsl,qe", "status", "okay", + sizeof("okay"), 0); +#endif +} +#endif diff --git a/board/freescale/p1021mds/tlb.c b/board/freescale/p1021mds/tlb.c new file mode 100644 index 0000000..f121552 --- /dev/null +++ b/board/freescale/p1021mds/tlb.c @@ -0,0 +1,100 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - PCIE */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, (CONFIG_SYS_PCIE2_MEM_VIRT + 0x10000000), + (CONFIG_SYS_PCIE2_MEM_PHYS + 0x10000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, (CONFIG_SYS_PCIE1_MEM_VIRT + 0x10000000), + (CONFIG_SYS_PCIE2_MEM_PHYS + 0x10000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCIE I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_IO_VIRT, CONFIG_SYS_PCIE2_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256K, 1), + + /* + * *I*G BCSR/PMC0/PMC1 + */ + SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_256K, 1), + + /* *I*G - NAND */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_1M, 1), + +#if defined(CONFIG_NAND_SPL) || defined(CONFIG_IN_TPL) + /* *I*G - L2SRAM */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 9, BOOKE_PAGESZ_256K, 1) +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 9f2b118..07425a3 100644 --- a/boards.cfg +++ b/boards.cfg @@ -550,6 +550,7 @@ P1020RDB_36BIT_SPIFLASH powerpc mpc85xx p1_p2_rdb freesca P1020RDB_NAND powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020RDB,NAND P1020RDB_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020RDB,SDCARD P1020RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020RDB,SPIFLASH +P1021MDS_NAND powerpc mpc85xx p1021mds freescale - P1021MDS:NAND P1022DS powerpc mpc85xx p1022ds freescale P1022DS_36BIT powerpc mpc85xx p1022ds freescale - P1022DS:36BIT P2010RDB powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010RDB diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c index 1ecb137..8edd6d5 100644 --- a/drivers/qe/uec.c +++ b/drivers/qe/uec.c @@ -31,6 +31,9 @@ #include "uec_phy.h" #include "miiphy.h" #include +#ifdef CONFIG_P1021MDS +#define BCSR11_ENET_MICRST 0x20 +#endif /* Default UTBIPAR SMI address */ #ifndef CONFIG_UTBIPAR_INIT_TBIPA @@ -1225,6 +1228,12 @@ static int uec_init(struct eth_device* dev, bd_t *bd) if (uec->the_first_run == 0) { #if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \ defined(CONFIG_P1021) || defined(CONFIG_P1025) +#ifdef CONFIG_P1021MDS + /* P1021MDS board needs to reset micrel phy for each UEC */ + clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 11), BCSR11_ENET_MICRST); + udelay(200); + setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 11), BCSR11_ENET_MICRST); +#endif /* QE9 and QE12 need to be set for enabling QE MII managment signals */ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE9); setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12); diff --git a/include/configs/P1021MDS.h b/include/configs/P1021MDS.h new file mode 100644 index 0000000..d0a0f21 --- /dev/null +++ b/include/configs/P1021MDS.h @@ -0,0 +1,629 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +/* + * p1021mds board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_BOOTSTRAP_SIZE (220 * 1024) + +#ifndef CONFIG_IN_BOOTSTRAP +#ifdef CONFIG_NAND +#define CONFIG_NAND_U_BOOT +#define CONFIG_RAMBOOT_NAND +#define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_TEXT_BASE_SPL 0xff800000 +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR +\ + CONFIG_SYS_L2_SIZE) +#else +#define CONFIG_SYS_TEXT_BASE 0x11001000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_BOOTSTRAP +#endif +#endif /* CONFIG_NAND */ +#else /* CONFIG_IN_BOOTSTRAP */ +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_TEXT_BASE 0xf8f84000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS (CONFIG_SYS_INIT_L2_ADDR +\ + CONFIG_SYS_NAND_SPL_SIZE +\ + CONFIG_BOOTSTRAP_SIZE - 4) +#define CONFIG_ENV_IS_NOWHERE + +#undef CONFIG_PARTITIONS +#define CONFIG_CMD_CACHE +#define CONFIG_SILENT_CONSOLE +#define CONFIG_SILENT_CONSOLE_AT_BOOT + +/* These CONFIG_RAMBOOT defines can not have any text in them as they + * are converted into strings to be placed in a u-boot command */ +#define CONFIG_RAMBOOT_LOAD 0x11000000 +#define CONFIG_RAMBOOT_SIZE 0x80000 + +#if defined(CONFIG_NAND) +#define CONFIG_NAND_FSL_ELBC +/* NANDboot has a slightly different start and offset address, again these + * defines can not have any strings in them */ +#define NEW_OFFSET 0x3b000 /* SPL + BOOTSTRAP size */ +#define CONFIG_BOOTCOMMAND "nand read " MK_STR(CONFIG_RAMBOOT_LOAD)\ + " " MK_STR(NEW_OFFSET) " "\ + MK_STR(CONFIG_RAMBOOT_SIZE) "; dcache flush;"\ + " icache flush; go " MK_STR(CONFIG_RAMBOOT_LOAD) +#else +#define CONFIG_BOOTCOMMAND "echo Bootstrap without known media!\n" +#endif +#define CONFIG_BOOTDELAY 0 +#endif /* CONFIG_IN_BOOTSTRAP */ + +/* High Level Configuration Options */ +#define CONFIG_BOOKE /* BOOKE */ +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_MPC85xx /* MPC8540/60/55/41/48/68/P1021 */ +#define CONFIG_P1021 /* P1021 silicon support */ +#define CONFIG_P1021MDS /* P1021MDS board specific */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ +#define CONFIG_FSL_ELBC /* Has Enhance localbus controller */ + +/* Replace a call to get_clock_freq (after it is implemented)*/ +#define CONFIG_SYS_CLK_FREQ 66666666 +#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_HWCONFIG + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x1fffffff + +#define CONFIG_SYS_LBC_LBCR 0x00080000 /* Implement conversion of + addresses in the LBC */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ + +#if defined(CONFIG_IN_BOOTSTRAP) || defined(CONFIG_NAND_SPL) +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#else +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfffe00000ull /* CCSRBAR Default */ +#else +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xffe00000 +#endif +#endif + +/* CCSRBAR PHYSICAL Address */ +/* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k + SPL code*/ +#if defined(CONFIG_NAND_U_BOOT) && defined(CONFIG_NAND_SPL) +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_DEFAULT +#else +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull +#else +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* phys addr of */ +#endif +#endif +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */ + +/* DDR Setup */ +#define CONFIG_FSL_DDR3 +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ +#define CONFIG_DDR_SPD +#define CONFIG_SYS_DDR_TLB_START 11 + +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 + /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +/* I2C addresses of SPD EEPROMs */ +#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ + +/* + * Config the L2 Cache as L2 SRAM + */ +#ifdef CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR +\ + CONFIG_SYS_L2_SIZE) +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#endif + +/* + * Memory map + * + * 0x0000_0000 0x1fff_ffff DDR3 512MB cacheable + * 0xa000_0000 0xbfff_ffff PCIE2 Mem 512MB non-cacheable + * 0xc000_0000 0xdfff_ffff PCIE1 Mem 512MB non-cacheable + * 0xffc1_0000 0xffc1_ffff PCIE2 IO range 64K non-cacheable + * 0xffc2_0000 0xffc2_ffff PCIE1 IO range 64K non-cacheable + * 0xf800_0000 0xf800_7fff BCSR on CS1 32KB non-cacheable + * 0xf801_0000 0xf801_ffff PMC1 on CS2 64KB non-cacheable + * 0xf802_0000 0xf802_ffff PMC0 on CS3 64KB non-cacheable + * 0xfc00_0000 0xfdff_ffff NAND on CS0 32MB non-cacheable + * 0xffe0_0000 0xffef_ffff CCSRBAR 1M + */ + + +/* + * Local Bus Definitions + */ + +#define CONFIG_SYS_BCSR_BASE 0xf8000000 +#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE + +#define CONFIG_SYS_PIB_PMC1_BASE 0xf8010000 + /* start of PIB-QOC3(PMC1) 64K */ +#define CONFIG_SYS_PIB_PMC1_BASE_PHYS CONFIG_SYS_PIB_PMC1_BASE + +#define CONFIG_SYS_PIB_PMC0_BASE 0xf8020000 + /* start of PIB-T1/E1(PMC0) 64K */ +#define CONFIG_SYS_PIB_PMC0_BASE_PHYS CONFIG_SYS_PIB_PMC0_BASE + +/* chip select 1 - BCSR*/ +#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \ + | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \ + | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +/* chip select 2 - PIB(QOC3-PMC1)*/ +#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PIB_PMC1_BASE_PHYS) \ + | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR2_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS \ + | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +/* chip select 3 - PIB(T1/E1-PMC0)*/ +#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PIB_PMC0_BASE_PHYS) \ + | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR3_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS \ + | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +#define CONFIG_SYS_NO_FLASH + +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_NAND_BASE 0xFF800000 +#else +#define CONFIG_SYS_NAND_BASE 0xFC000000 +#endif +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) + +/* NAND boot: 4K NAND loader config */ +#define CONFIG_SYS_NAND_SPL_SIZE 0x4000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE (CONFIG_BOOTSTRAP_SIZE +\ + CONFIG_SYS_NAND_SPL_SIZE) +#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) +#define CONFIG_SYS_NAND_U_BOOT_START (CONFIG_SYS_NAND_U_BOOT_DST +\ + CONFIG_SYS_NAND_U_BOOT_SIZE - 4) +#define CONFIG_SYS_NAND_U_BOOT_OFFS (0) +#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x5000) +#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) + +/* NAND FLASH CONFIG */ +#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ + | (2< " +#endif + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * Environment + */ +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#if defined(CONFIG_NAND) +#ifndef CONFIG_IN_BOOTSTRAP +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET (1024 * 1024) +#endif +#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR +\ + CONFIG_BOOTSTRAP_SIZE +\ + CONFIG_SYS_NAND_SPL_SIZE) +#endif + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* Boot Argument Buffer Size */ + +/*********************************/ + +#define CONFIG_MP /* Multiprocessor support */ + +#ifndef CONFIG_IN_BOOTSTRAP +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controller */ +#define CONFIG_PCIE2 /* PCIE controller */ +#define CONFIG_FSL_PCI_INIT /* use common fsl pci init code */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_TSEC_ENET /* tsec ethernet support */ + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +#define CONFIG_SYS_64BIT_VSPRINTF +#define CONFIG_SYS_64BIT_STRTOUL + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ +#endif + +/* TSEC support */ +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI +#endif + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define CONFIG_TSEC3 +#define CONFIG_TSEC3_NAME "eTSEC3" + +#define TSEC1_PHY_ADDR 0 +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC1_PHYIDX 0 + +#define TSEC2_PHY_ADDR 4 +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_SGMII) +#define TSEC2_PHYIDX 0 + +#ifdef CONFIG_TSEC3_IN_SGMII /* Need to set SW8.6 to 0 */ +#define TSEC3_PHY_ADDR 6 +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_SGMII) +#else +#define TSEC3_PHY_ADDR 1 +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#endif +#define TSEC3_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif /* CONFIG_TSEC_ENET */ + +#ifndef CONFIG_IN_BOOTSTRAP +#define CONFIG_QE +#endif + +#ifdef CONFIG_QE +/* QE microcode/firmware address */ +#define CONFIG_SYS_QE_FW_IN_NAND 0x1f00000 +#define CONFIG_SYS_QE_FW_ADDR 0x10000000 +#define CONFIG_SYS_QE_FW_LENGTH 0x10000 + +/* + * QE UEC ethernet configuration + */ +#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) + +#define CONFIG_UEC_ETH +#define CONFIG_PHY_MODE_NEED_CHANGE + +#define CONFIG_UEC_ETH1 /* GETH1 */ +#define CONFIG_HAS_ETH0 + +#ifdef CONFIG_UEC_ETH1 +#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK12 /* CLK12 for MII */ +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 /* CLK9 for MII */ +#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR 0x0 /* 0x0 for MII */ +#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII +#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 +#endif /* CONFIG_UEC_ETH1 */ + +#define CONFIG_UEC_ETH5 /* GETH5 */ +#define CONFIG_HAS_ETH1 + +#ifdef CONFIG_UEC_ETH5 +#define CONFIG_SYS_UEC5_UCC_NUM 4 /* UCC5 */ +#define CONFIG_SYS_UEC5_RX_CLK QE_CLK_NONE +#define CONFIG_SYS_UEC5_TX_CLK QE_CLK13 /* CLK 13 for RMII */ +#define CONFIG_SYS_UEC5_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC5_PHY_ADDR 0x3 /* 0x3 for RMII */ +#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII +#define CONFIG_SYS_UEC5_INTERFACE_SPEED 100 +#endif /* CONFIG_UEC_ETH2 */ + +#endif /* CONFIG_QE */ +/* + * I2C2 EEPROM + */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_BUS_NUM 1 + +#define PLPPAR1_I2C_BIT_MASK 0x0000000F +#define PLPPAR1_I2C2_VAL 0x00000000 +#define PLPPAR1_ESDHC_VAL 0x0000000A +#define PLPDIR1_I2C_BIT_MASK 0x0000000F +#define PLPDIR1_I2C2_VAL 0x0000000F +#define PLPDIR1_ESDHC_VAL 0x00000006 + +/* + * General PCI + * Memory Addresses are mapped 1-1. I/O is mapped from 0 + */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64K */ + +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ + +#if defined(CONFIG_PCI) +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#endif + +#ifndef CONFIG_IN_BOOTSTRAP +#define CONFIG_E1000 /* Enable E1000 PCI Ethernet Card */ + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ +#endif + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +#ifndef CONFIG_IN_BOOTSTRAP +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_SETEXPR + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif +#endif /* CONFIG_IN_BOOTSTRAP */ + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ + +#define CONFIG_MMC +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#ifndef CONFIG_IN_BOOTSTRAP +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif +#endif + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) + /* Initial Memory map for Linux*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_HOSTNAME p1021mds +#define CONFIG_ROOTPATH /nfsroot +#define CONFIG_BOOTFILE uImage + +#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ + +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=rootfs.ext2.gz.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=p1021mds.dtb\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs\0" \ + "ramargs=setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs\0" \ + "hwconfig=fsl_ddr:ctrl_intlv=null\0" \ + +#define CONFIG_NFSBOOTCOMMAND \ + "run nfsargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "run ramargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr $ramdiskaddr" + +#ifndef CONFIG_IN_BOOTSTRAP +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND +#endif + +#endif /* __CONFIG_H */ diff --git a/nand_spl/board/freescale/p1021mds/Makefile b/nand_spl/board/freescale/p1021mds/Makefile new file mode 100644 index 0000000..fb63da2 --- /dev/null +++ b/nand_spl/board/freescale/p1021mds/Makefile @@ -0,0 +1,137 @@ +# +# Copyright (C) 2010-2011 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +NAND_SPL := y +PAD_TO := 0xff804000 + +include $(TOPDIR)/config.mk + +nandobj := $(OBJTREE)/nand_spl/ + +LDSCRIPT= $(TOPDIR)/$(CPUDIR)/u-boot-nand_spl.lds +LDFLAGS := -T $(nandobj)u-boot-nand_spl.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) $(LDFLAGS) \ + $(LDFLAGS_FINAL) +AFLAGS += -DCONFIG_NAND_SPL +CFLAGS += -DCONFIG_NAND_SPL + +SOBJS = start.o resetvec.o +COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \ + nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR) + +ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin + +all: $(obj).depend $(ALL) + +$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds + cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ + -Map $(nandobj)u-boot-spl.map \ + -o $(nandobj)u-boot-spl + +$(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT) + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ + +# create symbolic links for common files + +$(obj)cache.c: + @rm -f $(obj)cache.c + ln -sf $(SRCTREE)/arch/powerpc/lib/cache.c $(obj)cache.c + +$(obj)cpu_init_early.c: + @rm -f $(obj)cpu_init_early.c + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/cpu_init_early.c \ + $(obj)cpu_init_early.c + +$(obj)cpu_init_nand.c: + @rm -f $(obj)cpu_init_nand.c + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c \ + $(obj)cpu_init_nand.c + +$(obj)fsl_law.c: + @rm -f $(obj)fsl_law.c + ln -sf $(SRCTREE)/drivers/misc/fsl_law.c $(obj)fsl_law.c + +$(obj)law.c: + @rm -f $(obj)law.c + ln -sf $(SRCTREE)/board/$(BOARDDIR)/law.c $(obj)law.c + +$(obj)nand_boot_fsl_elbc.c: + @rm -f $(obj)nand_boot_fsl_elbc.c + ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c \ + $(obj)nand_boot_fsl_elbc.c + +$(obj)ns16550.c: + @rm -f $(obj)ns16550.c + ln -sf $(SRCTREE)/drivers/serial/ns16550.c $(obj)ns16550.c + +$(obj)resetvec.S: + @rm -f $(obj)resetvec.S + ln -s $(SRCTREE)/arch/powerpc/cpu/$(CPU)/resetvec.S $(obj)resetvec.S + +$(obj)fixed_ivor.S: + @rm -f $(obj)fixed_ivor.S + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/fixed_ivor.S \ + $(obj)fixed_ivor.S + +$(obj)start.S: $(obj)fixed_ivor.S + @rm -f $(obj)start.S + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/start.S $(obj)start.S + +$(obj)tlb.c: + @rm -f $(obj)tlb.c + ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/tlb.c $(obj)tlb.c + +$(obj)tlb_table.c: + @rm -f $(obj)tlb_table.c + ln -sf $(SRCTREE)/board/$(BOARDDIR)/tlb.c $(obj)tlb_table.c + +ifneq ($(OBJTREE), $(SRCTREE)) +$(obj)nand_boot.c: + @rm -f $(obj)nand_boot.c + ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c \ + $(obj)nand_boot.c +endif + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/nand_spl/board/freescale/p1021mds/nand_boot.c b/nand_spl/board/freescale/p1021mds/nand_boot.c new file mode 100644 index 0000000..a52b50a --- /dev/null +++ b/nand_spl/board/freescale/p1021mds/nand_boot.c @@ -0,0 +1,69 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +void board_init_f(ulong bootflag) +{ + uint plat_ratio, bus_clk, sys_clk = 0; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + sys_clk = CONFIG_SYS_CLK_FREQ; + + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + bus_clk = plat_ratio * sys_clk; + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + /* copy code to DDR and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0, + CONFIG_SYS_NAND_U_BOOT_RELOC); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +}