@@ -17,6 +17,10 @@
# Board CPU #
#########################################################################
+Haiying Wang <Haiying.Wang@freescale.com>
+
+ P1021MDS P1021
+
Poonam Aggrwal <poonam.aggrwal@freescale.com>
P2020RDB P2020
@@ -2225,6 +2225,19 @@ FIT uImage format:
Adds the MTD partitioning infrastructure from the Linux
kernel. Needed for UBI support.
+- NAND Boot Support
+ CONFIG_NAND_U_BOOT
+
+ Builds a U-Boot image that boots from NAND, prefixed by a small
+ loader stub (secondary program loader -- SPL) that loads the
+ rest of U-Boot into RAM. This symbol will be set in all build
+ phases.
+
+ CONFIG_NAND_SPL
+
+ This is set by the build system when compiling code to go into
+ the SPL. It is not set when building the code that the SPL
+ loads.
Modem Support:
--------------
new file mode 100644
@@ -0,0 +1,52 @@
+#
+# Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS-y += $(BOARD).o
+COBJS-y += law.o
+COBJS-y += tlb.o
+COBJS-y += ddr.o
+
+SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS-y))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
new file mode 100644
@@ -0,0 +1,81 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ /*
+ * Factors to consider for clock adjust:
+ */
+ popts->clk_adjust = 6;
+
+ /*
+ * Factors to consider for CPO:
+ */
+ popts->cpo_override = 0x1f;
+
+ /*
+ * Factors to consider for write data delay:
+ */
+ popts->write_data_delay = 2;
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ */
+ popts->half_strength_driver_enable = 1;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 1;
+ popts->rtt_override_value = DDR3_RTT_40_OHM; /* 40 Ohm rtt */
+ popts->rtt_wr_override_value = 2; /* Rtt_WR */
+
+ /* Write leveling override */
+ popts->wrlvl_en = 1;
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xa;
+ popts->wrlvl_start = 0x8;
+ /*
+ * P1021 supports max 32-bit DDR width
+ */
+ popts->data_bus_width = 1;
+
+ /*
+ * disable on-the-fly burst chop mode for 32 bit data bus
+ */
+ popts->OTF_burst_chop_en = 0;
+
+ /*
+ * Set fixed 8 beat burst for 32 bit data bus
+ */
+ popts->burst_length = DDR_BL8;
+}
new file mode 100644
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_256K, LAW_TRGT_IF_LBC),
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
new file mode 100644
@@ -0,0 +1,181 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <hwconfig.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <asm/io.h>
+#include <asm/mp.h>
+#include <i2c.h>
+#include <ioports.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <fsl_esdhc.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <netdev.h>
+
+#ifdef CONFIG_QE
+const qe_iop_conf_t qe_iop_conf_tab[] = {
+ /* QE_MUX_MDC */
+ {1, 19, 1, 0, 1}, /* QE_MUX_MDC */
+ /* QE_MUX_MDIO */
+ {1, 20, 3, 0, 1}, /* QE_MUX_MDIO */
+
+ /* UCC_1_MII */
+ {0, 23, 2, 0, 2}, /* CLK12 */
+ {0, 24, 2, 0, 1}, /* CLK9 */
+ {0, 7, 1, 0, 2}, /* ENET1_TXD0_SER1_TXD0 */
+ {0, 9, 1, 0, 2}, /* ENET1_TXD1_SER1_TXD1 */
+ {0, 11, 1, 0, 2}, /* ENET1_TXD2_SER1_TXD2 */
+ {0, 12, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3 */
+ {0, 6, 2, 0, 2}, /* ENET1_RXD0_SER1_RXD0 */
+ {0, 10, 2, 0, 2}, /* ENET1_RXD1_SER1_RXD1 */
+ {0, 14, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2 */
+ {0, 15, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3 */
+ {0, 5, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */
+ {0, 13, 1, 0, 2}, /* ENET1_TX_ER */
+ {0, 4, 2, 0, 2}, /* ENET1_RX_DV_SER1_CTS_B */
+ {0, 8, 2, 0, 2}, /* ENET1_RX_ER_SER1_CD_B */
+ {0, 17, 2, 0, 2}, /* ENET1_CRS */
+ {0, 16, 2, 0, 2}, /* ENET1_COL */
+
+ /* UCC_5_RMII */
+ {1, 11, 2, 0, 1}, /* CLK13 */
+ {1, 7, 1, 0, 2}, /* ENET5_TXD0_SER5_TXD0 */
+ {1, 10, 1, 0, 2}, /* ENET5_TXD1_SER5_TXD1 */
+ {1, 6, 2, 0, 2}, /* ENET5_RXD0_SER5_RXD0 */
+ {1, 9, 2, 0, 2}, /* ENET5_RXD1_SER5_RXD1 */
+ {1, 5, 1, 0, 2}, /* ENET5_TX_EN_SER5_RTS_B */
+ {1, 4, 2, 0, 2}, /* ENET5_RX_DV_SER5_CTS_B */
+ {1, 8, 2, 0, 2}, /* ENET5_RX_ER_SER5_CD_B */
+
+ {0, 0, 0, 0, QE_IOP_TAB_END} /* END of table */
+};
+#endif
+
+int board_early_init_f(void)
+{
+
+ fsl_lbc_t *lbc = LBC_BASE_ADDR;
+
+#ifdef CONFIG_MMC
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ setbits_be32(&gur->pmuxcr,
+ (MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP));
+#endif
+
+ /* Set ABSWP to implement conversion of addresses in the LBC */
+ setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ printf("Board: P1021 MDS\n");
+
+ return 0;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+#endif
+
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+ struct fsl_pq_mdio_info mdio_info;
+ struct tsec_info_struct tsec_info[3];
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ int num = 0;
+
+#ifdef CONFIG_TSEC1
+ SET_STD_TSEC_INFO(tsec_info[num], 1);
+ num++;
+#endif
+
+#ifdef CONFIG_TSEC2
+ SET_STD_TSEC_INFO(tsec_info[num], 2);
+ num++;
+#endif
+
+#ifdef CONFIG_TSEC3
+ SET_STD_TSEC_INFO(tsec_info[num], 3);
+ if (!(in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_SGMII3_DIS))
+ tsec_info[num].flags |= TSEC_SGMII;
+ num++;
+#endif
+
+ if (!num) {
+ printf("No TSECs initialized\n");
+ return 0;
+ }
+
+ mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+ mdio_info.name = DEFAULT_MII_NAME;
+
+ fsl_pq_mdio_init(bis, &mdio_info);
+
+ tsec_eth_init(bis, tsec_info, num);
+
+#if defined(CONFIG_UEC_ETH)
+ /* QE0 and QE3 need to be exposed for UCC1 and UCC5 Eth mode */
+ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE0);
+ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE3);
+
+ uec_standard_init(bis);
+#endif
+
+ return pci_eth_init(bis);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, base, size);
+
+ FT_FSL_PCI_SETUP;
+
+#ifdef CONFIG_QE
+ do_fixup_by_compat(blob, "fsl,qe", "status", "okay",
+ sizeof("okay"), 0);
+#endif
+}
+#endif
new file mode 100644
@@ -0,0 +1,100 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_1M, 1),
+
+ /* *I*G* - PCIE */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+ SET_TLB_ENTRY(1, (CONFIG_SYS_PCIE2_MEM_VIRT + 0x10000000),
+ (CONFIG_SYS_PCIE2_MEM_PHYS + 0x10000000),
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_256M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+
+ SET_TLB_ENTRY(1, (CONFIG_SYS_PCIE1_MEM_VIRT + 0x10000000),
+ (CONFIG_SYS_PCIE2_MEM_PHYS + 0x10000000),
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCIE I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_IO_VIRT, CONFIG_SYS_PCIE2_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256K, 1),
+
+ /*
+ * *I*G BCSR/PMC0/PMC1
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 7, BOOKE_PAGESZ_256K, 1),
+
+ /* *I*G - NAND */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 8, BOOKE_PAGESZ_1M, 1),
+
+#if defined(CONFIG_NAND_SPL) || defined(CONFIG_IN_TPL)
+ /* *I*G - L2SRAM */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+ 0, 9, BOOKE_PAGESZ_256K, 1)
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
@@ -550,6 +550,7 @@ P1020RDB_36BIT_SPIFLASH powerpc mpc85xx p1_p2_rdb freesca
P1020RDB_NAND powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020RDB,NAND
P1020RDB_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020RDB,SDCARD
P1020RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020RDB,SPIFLASH
+P1021MDS_NAND powerpc mpc85xx p1021mds freescale - P1021MDS:NAND
P1022DS powerpc mpc85xx p1022ds freescale
P1022DS_36BIT powerpc mpc85xx p1022ds freescale - P1022DS:36BIT
P2010RDB powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010RDB
@@ -31,6 +31,9 @@
#include "uec_phy.h"
#include "miiphy.h"
#include <phy.h>
+#ifdef CONFIG_P1021MDS
+#define BCSR11_ENET_MICRST 0x20
+#endif
/* Default UTBIPAR SMI address */
#ifndef CONFIG_UTBIPAR_INIT_TBIPA
@@ -1225,6 +1228,12 @@ static int uec_init(struct eth_device* dev, bd_t *bd)
if (uec->the_first_run == 0) {
#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \
defined(CONFIG_P1021) || defined(CONFIG_P1025)
+#ifdef CONFIG_P1021MDS
+ /* P1021MDS board needs to reset micrel phy for each UEC */
+ clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 11), BCSR11_ENET_MICRST);
+ udelay(200);
+ setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 11), BCSR11_ENET_MICRST);
+#endif
/* QE9 and QE12 need to be set for enabling QE MII managment signals */
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE9);
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12);
new file mode 100644
@@ -0,0 +1,629 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+/*
+ * p1021mds board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_BOOTSTRAP_SIZE (220 * 1024)
+
+#ifndef CONFIG_IN_BOOTSTRAP
+#ifdef CONFIG_NAND
+#define CONFIG_NAND_U_BOOT
+#define CONFIG_RAMBOOT_NAND
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_TEXT_BASE_SPL 0xff800000
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#define CONFIG_SYS_L2_SIZE (256 << 10)
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR +\
+ CONFIG_SYS_L2_SIZE)
+#else
+#define CONFIG_SYS_TEXT_BASE 0x11001000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_BOOTSTRAP
+#endif
+#endif /* CONFIG_NAND */
+#else /* CONFIG_IN_BOOTSTRAP */
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_TEXT_BASE 0xf8f84000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS (CONFIG_SYS_INIT_L2_ADDR +\
+ CONFIG_SYS_NAND_SPL_SIZE +\
+ CONFIG_BOOTSTRAP_SIZE - 4)
+#define CONFIG_ENV_IS_NOWHERE
+
+#undef CONFIG_PARTITIONS
+#define CONFIG_CMD_CACHE
+#define CONFIG_SILENT_CONSOLE
+#define CONFIG_SILENT_CONSOLE_AT_BOOT
+
+/* These CONFIG_RAMBOOT defines can not have any text in them as they
+ * are converted into strings to be placed in a u-boot command */
+#define CONFIG_RAMBOOT_LOAD 0x11000000
+#define CONFIG_RAMBOOT_SIZE 0x80000
+
+#if defined(CONFIG_NAND)
+#define CONFIG_NAND_FSL_ELBC
+/* NANDboot has a slightly different start and offset address, again these
+ * defines can not have any strings in them */
+#define NEW_OFFSET 0x3b000 /* SPL + BOOTSTRAP size */
+#define CONFIG_BOOTCOMMAND "nand read " MK_STR(CONFIG_RAMBOOT_LOAD)\
+ " " MK_STR(NEW_OFFSET) " "\
+ MK_STR(CONFIG_RAMBOOT_SIZE) "; dcache flush;"\
+ " icache flush; go " MK_STR(CONFIG_RAMBOOT_LOAD)
+#else
+#define CONFIG_BOOTCOMMAND "echo Bootstrap without known media!\n"
+#endif
+#define CONFIG_BOOTDELAY 0
+#endif /* CONFIG_IN_BOOTSTRAP */
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE /* BOOKE */
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_MPC85xx /* MPC8540/60/55/41/48/68/P1021 */
+#define CONFIG_P1021 /* P1021 silicon support */
+#define CONFIG_P1021MDS /* P1021MDS board specific */
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_FSL_ELBC /* Has Enhance localbus controller */
+
+/* Replace a call to get_clock_freq (after it is implemented)*/
+#define CONFIG_SYS_CLK_FREQ 66666666
+#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+
+#define CONFIG_HWCONFIG
+
+/*
+ * Only possible on E500 Version 2 or newer cores.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x1fffffff
+
+#define CONFIG_SYS_LBC_LBCR 0x00080000 /* Implement conversion of
+ addresses in the LBC */
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
+
+#if defined(CONFIG_IN_BOOTSTRAP) || defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#else
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfffe00000ull /* CCSRBAR Default */
+#else
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xffe00000
+#endif
+#endif
+
+/* CCSRBAR PHYSICAL Address */
+/* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
+ SPL code*/
+#if defined(CONFIG_NAND_U_BOOT) && defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_DEFAULT
+#else
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* phys addr of */
+#endif
+#endif
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR3
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_DDR_TLB_START 11
+
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+ /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
+
+/*
+ * Config the L2 Cache as L2 SRAM
+ */
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_L2_SIZE (256 << 10)
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR +\
+ CONFIG_SYS_L2_SIZE)
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#endif
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x1fff_ffff DDR3 512MB cacheable
+ * 0xa000_0000 0xbfff_ffff PCIE2 Mem 512MB non-cacheable
+ * 0xc000_0000 0xdfff_ffff PCIE1 Mem 512MB non-cacheable
+ * 0xffc1_0000 0xffc1_ffff PCIE2 IO range 64K non-cacheable
+ * 0xffc2_0000 0xffc2_ffff PCIE1 IO range 64K non-cacheable
+ * 0xf800_0000 0xf800_7fff BCSR on CS1 32KB non-cacheable
+ * 0xf801_0000 0xf801_ffff PMC1 on CS2 64KB non-cacheable
+ * 0xf802_0000 0xf802_ffff PMC0 on CS3 64KB non-cacheable
+ * 0xfc00_0000 0xfdff_ffff NAND on CS0 32MB non-cacheable
+ * 0xffe0_0000 0xffef_ffff CCSRBAR 1M
+ */
+
+
+/*
+ * Local Bus Definitions
+ */
+
+#define CONFIG_SYS_BCSR_BASE 0xf8000000
+#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE
+
+#define CONFIG_SYS_PIB_PMC1_BASE 0xf8010000
+ /* start of PIB-QOC3(PMC1) 64K */
+#define CONFIG_SYS_PIB_PMC1_BASE_PHYS CONFIG_SYS_PIB_PMC1_BASE
+
+#define CONFIG_SYS_PIB_PMC0_BASE 0xf8020000
+ /* start of PIB-T1/E1(PMC0) 64K */
+#define CONFIG_SYS_PIB_PMC0_BASE_PHYS CONFIG_SYS_PIB_PMC0_BASE
+
+/* chip select 1 - BCSR*/
+#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
+ | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
+ | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+
+/* chip select 2 - PIB(QOC3-PMC1)*/
+#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PIB_PMC1_BASE_PHYS) \
+ | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR2_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS \
+ | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+
+/* chip select 3 - PIB(T1/E1-PMC0)*/
+#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PIB_PMC0_BASE_PHYS) \
+ | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR3_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS \
+ | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+
+#define CONFIG_SYS_NO_FLASH
+
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_SYS_NAND_BASE 0xFF800000
+#else
+#define CONFIG_SYS_NAND_BASE 0xFC000000
+#endif
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
+
+/* NAND boot: 4K NAND loader config */
+#define CONFIG_SYS_NAND_SPL_SIZE 0x4000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (CONFIG_BOOTSTRAP_SIZE +\
+ CONFIG_SYS_NAND_SPL_SIZE)
+#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR)
+#define CONFIG_SYS_NAND_U_BOOT_START (CONFIG_SYS_NAND_U_BOOT_DST +\
+ CONFIG_SYS_NAND_U_BOOT_SIZE - 4)
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
+#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x5000)
+#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
+
+/* NAND FLASH CONFIG */
+#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR)
+/* chip select 0 - NAND */
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SERIAL_MULTI
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_NS16550_MIN_FUNCTIONS
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+/* Use the HUSH parser*/
+#ifndef CONFIG_IN_BOOTSTRAP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#if defined(CONFIG_NAND)
+#ifndef CONFIG_IN_BOOTSTRAP
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET (1024 * 1024)
+#endif
+#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR +\
+ CONFIG_BOOTSTRAP_SIZE +\
+ CONFIG_SYS_NAND_SPL_SIZE)
+#endif
+
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
+ /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+ /* Boot Argument Buffer Size */
+
+/*********************************/
+
+#define CONFIG_MP /* Multiprocessor support */
+
+#ifndef CONFIG_IN_BOOTSTRAP
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controller */
+#define CONFIG_PCIE2 /* PCIE controller */
+#define CONFIG_FSL_PCI_INIT /* use common fsl pci init code */
+#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+#define CONFIG_SYS_64BIT_VSPRINTF
+#define CONFIG_SYS_64BIT_STRTOUL
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+#endif
+
+/* TSEC support */
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define CONFIG_TSEC3
+#define CONFIG_TSEC3_NAME "eTSEC3"
+
+#define TSEC1_PHY_ADDR 0
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC1_PHYIDX 0
+
+#define TSEC2_PHY_ADDR 4
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_SGMII)
+#define TSEC2_PHYIDX 0
+
+#ifdef CONFIG_TSEC3_IN_SGMII /* Need to set SW8.6 to 0 */
+#define TSEC3_PHY_ADDR 6
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_SGMII)
+#else
+#define TSEC3_PHY_ADDR 1
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#endif
+#define TSEC3_PHYIDX 0
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif /* CONFIG_TSEC_ENET */
+
+#ifndef CONFIG_IN_BOOTSTRAP
+#define CONFIG_QE
+#endif
+
+#ifdef CONFIG_QE
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FW_IN_NAND 0x1f00000
+#define CONFIG_SYS_QE_FW_ADDR 0x10000000
+#define CONFIG_SYS_QE_FW_LENGTH 0x10000
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120)
+
+#define CONFIG_UEC_ETH
+#define CONFIG_PHY_MODE_NEED_CHANGE
+
+#define CONFIG_UEC_ETH1 /* GETH1 */
+#define CONFIG_HAS_ETH0
+
+#ifdef CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
+#define CONFIG_SYS_UEC1_RX_CLK QE_CLK12 /* CLK12 for MII */
+#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 /* CLK9 for MII */
+#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR 0x0 /* 0x0 for MII */
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
+#endif /* CONFIG_UEC_ETH1 */
+
+#define CONFIG_UEC_ETH5 /* GETH5 */
+#define CONFIG_HAS_ETH1
+
+#ifdef CONFIG_UEC_ETH5
+#define CONFIG_SYS_UEC5_UCC_NUM 4 /* UCC5 */
+#define CONFIG_SYS_UEC5_RX_CLK QE_CLK_NONE
+#define CONFIG_SYS_UEC5_TX_CLK QE_CLK13 /* CLK 13 for RMII */
+#define CONFIG_SYS_UEC5_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC5_PHY_ADDR 0x3 /* 0x3 for RMII */
+#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC5_INTERFACE_SPEED 100
+#endif /* CONFIG_UEC_ETH2 */
+
+#endif /* CONFIG_QE */
+/*
+ * I2C2 EEPROM
+ */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_BUS_NUM 1
+
+#define PLPPAR1_I2C_BIT_MASK 0x0000000F
+#define PLPPAR1_I2C2_VAL 0x00000000
+#define PLPPAR1_ESDHC_VAL 0x0000000A
+#define PLPDIR1_I2C_BIT_MASK 0x0000000F
+#define PLPDIR1_I2C2_VAL 0x0000000F
+#define PLPDIR1_ESDHC_VAL 0x00000006
+
+/*
+ * General PCI
+ * Memory Addresses are mapped 1-1. I/O is mapped from 0
+ */
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64K */
+
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */
+
+#if defined(CONFIG_PCI)
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#endif
+
+#ifndef CONFIG_IN_BOOTSTRAP
+#define CONFIG_E1000 /* Enable E1000 PCI Ethernet Card */
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+#endif
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+#ifndef CONFIG_IN_BOOTSTRAP
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_SETEXPR
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+#endif
+#endif /* CONFIG_IN_BOOTSTRAP */
+
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
+
+#define CONFIG_MMC
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#ifndef CONFIG_IN_BOOTSTRAP
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+#endif
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20)
+ /* Initial Memory map for Linux*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_HOSTNAME p1021mds
+#define CONFIG_ROOTPATH /nfsroot
+#define CONFIG_BOOTFILE uImage
+
+#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
+
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=rootfs.ext2.gz.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=p1021mds.dtb\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs\0" \
+ "hwconfig=fsl_ddr:ctrl_intlv=null\0" \
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "run nfsargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "run ramargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "bootm $loadaddr $ramdiskaddr"
+
+#ifndef CONFIG_IN_BOOTSTRAP
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
+#endif
+
+#endif /* __CONFIG_H */
new file mode 100644
@@ -0,0 +1,137 @@
+#
+# Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+NAND_SPL := y
+PAD_TO := 0xff804000
+
+include $(TOPDIR)/config.mk
+
+nandobj := $(OBJTREE)/nand_spl/
+
+LDSCRIPT= $(TOPDIR)/$(CPUDIR)/u-boot-nand_spl.lds
+LDFLAGS := -T $(nandobj)u-boot-nand_spl.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) $(LDFLAGS) \
+ $(LDFLAGS_FINAL)
+AFLAGS += -DCONFIG_NAND_SPL
+CFLAGS += -DCONFIG_NAND_SPL
+
+SOBJS = start.o resetvec.o
+COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \
+ nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o
+
+SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS := $(SOBJS) $(COBJS)
+LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR)
+
+ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+
+all: $(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \
+ -Map $(nandobj)u-boot-spl.map \
+ -o $(nandobj)u-boot-spl
+
+$(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT)
+ $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
+
+# create symbolic links for common files
+
+$(obj)cache.c:
+ @rm -f $(obj)cache.c
+ ln -sf $(SRCTREE)/arch/powerpc/lib/cache.c $(obj)cache.c
+
+$(obj)cpu_init_early.c:
+ @rm -f $(obj)cpu_init_early.c
+ ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/cpu_init_early.c \
+ $(obj)cpu_init_early.c
+
+$(obj)cpu_init_nand.c:
+ @rm -f $(obj)cpu_init_nand.c
+ ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c \
+ $(obj)cpu_init_nand.c
+
+$(obj)fsl_law.c:
+ @rm -f $(obj)fsl_law.c
+ ln -sf $(SRCTREE)/drivers/misc/fsl_law.c $(obj)fsl_law.c
+
+$(obj)law.c:
+ @rm -f $(obj)law.c
+ ln -sf $(SRCTREE)/board/$(BOARDDIR)/law.c $(obj)law.c
+
+$(obj)nand_boot_fsl_elbc.c:
+ @rm -f $(obj)nand_boot_fsl_elbc.c
+ ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c \
+ $(obj)nand_boot_fsl_elbc.c
+
+$(obj)ns16550.c:
+ @rm -f $(obj)ns16550.c
+ ln -sf $(SRCTREE)/drivers/serial/ns16550.c $(obj)ns16550.c
+
+$(obj)resetvec.S:
+ @rm -f $(obj)resetvec.S
+ ln -s $(SRCTREE)/arch/powerpc/cpu/$(CPU)/resetvec.S $(obj)resetvec.S
+
+$(obj)fixed_ivor.S:
+ @rm -f $(obj)fixed_ivor.S
+ ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/fixed_ivor.S \
+ $(obj)fixed_ivor.S
+
+$(obj)start.S: $(obj)fixed_ivor.S
+ @rm -f $(obj)start.S
+ ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/start.S $(obj)start.S
+
+$(obj)tlb.c:
+ @rm -f $(obj)tlb.c
+ ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/tlb.c $(obj)tlb.c
+
+$(obj)tlb_table.c:
+ @rm -f $(obj)tlb_table.c
+ ln -sf $(SRCTREE)/board/$(BOARDDIR)/tlb.c $(obj)tlb_table.c
+
+ifneq ($(OBJTREE), $(SRCTREE))
+$(obj)nand_boot.c:
+ @rm -f $(obj)nand_boot.c
+ ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c \
+ $(obj)nand_boot.c
+endif
+
+#########################################################################
+
+$(obj)%.o: $(obj)%.S
+ $(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o: $(obj)%.c
+ $(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
new file mode 100644
@@ -0,0 +1,69 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+#include <common.h>
+#include <mpc85xx.h>
+#include <asm/io.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void board_init_f(ulong bootflag)
+{
+ uint plat_ratio, bus_clk, sys_clk = 0;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ sys_clk = CONFIG_SYS_CLK_FREQ;
+
+ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+ plat_ratio >>= 1;
+ bus_clk = plat_ratio * sys_clk;
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ bus_clk / 16 / CONFIG_BAUDRATE);
+
+ puts("\nNAND boot... ");
+ /* copy code to DDR and jump to it - this should not return */
+ /* NOTE - code has to be copied out of NAND buffer before
+ * other blocks can be read.
+ */
+ relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0,
+ CONFIG_SYS_NAND_U_BOOT_RELOC);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ nand_boot();
+}
+
+void putc(char c)
+{
+ if (c == '\n')
+ NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+
+ NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+}
+
+void puts(const char *str)
+{
+ while (*str)
+ putc(*str++);
+}