[v5,2/2] PCI: amlogic: Add the Amlogic Meson PCIe controller driver

Message ID 1539049990-30810-3-git-send-email-hanjie.lin@amlogic.com
State Changes Requested
Delegated to: Lorenzo Pieralisi
Headers show
Series
  • add the Amlogic Meson PCIe controller driver
Related show

Commit Message

Hanjie Lin Oct. 9, 2018, 1:53 a.m.
From: Yue Wang <yue.wang@amlogic.com>

The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
PCI core. This patch adds the driver support for Meson PCIe controller.

Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
---
 MAINTAINERS                            |   7 +
 drivers/pci/controller/dwc/Kconfig     |  10 +
 drivers/pci/controller/dwc/Makefile    |   1 +
 drivers/pci/controller/dwc/pci-meson.c | 593 +++++++++++++++++++++++++++++++++
 4 files changed, 611 insertions(+)
 create mode 100644 drivers/pci/controller/dwc/pci-meson.c

Comments

Lorenzo Pieralisi Nov. 16, 2018, 5:49 p.m. | #1
On Tue, Oct 09, 2018 at 09:53:10AM +0800, Hanjie Lin wrote:
> From: Yue Wang <yue.wang@amlogic.com>
> 
> The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
> PCI core. This patch adds the driver support for Meson PCIe controller.
> 
> Signed-off-by: Yue Wang <yue.wang@amlogic.com>
> Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
> ---
>  MAINTAINERS                            |   7 +
>  drivers/pci/controller/dwc/Kconfig     |  10 +
>  drivers/pci/controller/dwc/Makefile    |   1 +
>  drivers/pci/controller/dwc/pci-meson.c | 593 +++++++++++++++++++++++++++++++++
>  4 files changed, 611 insertions(+)
>  create mode 100644 drivers/pci/controller/dwc/pci-meson.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 02a3961..da579ef 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -11333,6 +11333,13 @@ L:	linux-pci@vger.kernel.org
>  S:	Maintained
>  F:	drivers/pci/controller/dwc/*spear*
>  
> +PCIE DRIVER FOR AMLOGIC MESON

Entries for PCIe host bridges are in alphabetical order, this one
isn't so you should fix it.

> +M:	Yue Wang <yue.wang@Amlogic.com>
> +L:	linux-pci@vger.kernel.org
> +L:	linux-amlogic@lists.infradead.org
> +S:	Maintained
> +F:	drivers/pci/controller/dwc/pci-meson.c
> +
>  PCMCIA SUBSYSTEM
>  M:	Dominik Brodowski <linux@dominikbrodowski.net>
>  T:	git git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia.git
> diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> index 91b0194..7800322 100644
> --- a/drivers/pci/controller/dwc/Kconfig
> +++ b/drivers/pci/controller/dwc/Kconfig
> @@ -193,4 +193,14 @@ config PCIE_HISI_STB
>  	help
>            Say Y here if you want PCIe controller support on HiSilicon STB SoCs
>  
> +config PCI_MESON
> +	bool "MESON PCIe controller"
> +	depends on PCI_MSI_IRQ_DOMAIN
> +	select PCIE_DW_HOST
> +	help
> +	  Say Y here if you want to enable PCI controller support on Amlogic
> +	  SoCs. The PCI controller on Amlogic is based on DesignWare hardware
> +	  and therefore the driver re-uses the DesignWare core functions to
> +	  implement the driver.
> +
>  endmenu
> diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
> index 5d2ce72..cf676bd 100644
> --- a/drivers/pci/controller/dwc/Makefile
> +++ b/drivers/pci/controller/dwc/Makefile
> @@ -14,6 +14,7 @@ obj-$(CONFIG_PCIE_ARMADA_8K) += pcie-armada8k.o
>  obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
>  obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o
>  obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
> +obj-$(CONFIG_PCI_MESON) += pci-meson.o
>  
>  # The following drivers are for devices that use the generic ACPI
>  # pci_root.c driver but don't support standard ECAM config access.
> diff --git a/drivers/pci/controller/dwc/pci-meson.c b/drivers/pci/controller/dwc/pci-meson.c
> new file mode 100644
> index 0000000..2278b48
> --- /dev/null
> +++ b/drivers/pci/controller/dwc/pci-meson.c
> @@ -0,0 +1,593 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * PCIe host controller driver for Amlogic MESON SoCs
> + *
> + * Copyright (c) 2018 Amlogic, inc.
> + * Author: Yue Wang <yue.wang@amlogic.com>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +#include <linux/resource.h>
> +#include <linux/types.h>
> +#include <linux/reset.h>
> +
> +#include "pcie-designware.h"
> +
> +#define to_meson_pcie(x) dev_get_drvdata((x)->dev)
> +
> +/* External local bus interface registers */
> +#define PLR_OFFSET			0x700
> +#define PCIE_PORT_LINK_CTRL_OFF		(PLR_OFFSET + 0x10)
> +#define FAST_LINK_MODE			BIT(7)
> +#define LINK_CAPABLE_MASK		GENMASK(21, 16)
> +#define LINK_CAPABLE_X1			BIT(16)
> +
> +#define PCIE_GEN2_CTRL_OFF		(PLR_OFFSET + 0x10c)
> +#define NUM_OF_LANES_MASK		GENMASK(12, 8)
> +#define NUM_OF_LANES_X1			BIT(8)
> +#define DIRECT_SPEED_CHANGE		BIT(17)
> +
> +#define TYPE1_HDR_OFFSET		0x0
> +#define PCIE_STATUS_COMMAND		(TYPE1_HDR_OFFSET + 0x04)
> +#define PCI_IO_EN			BIT(0)
> +#define PCI_MEM_SPACE_EN		BIT(1)
> +#define PCI_BUS_MASTER_EN		BIT(2)
> +#define PCIE_BASE_ADDR0			(TYPE1_HDR_OFFSET + 0x10)
> +#define PCIE_BASE_ADDR1			(TYPE1_HDR_OFFSET + 0x14)
> +
> +#define PCIE_CAP_OFFSET			0x70
> +#define PCIE_DEV_CTRL_DEV_STUS		(PCIE_CAP_OFFSET + 0x08)
> +#define PCIE_CAP_MAX_PAYLOAD_MASK	GENMASK(7, 5)
> +#define PCIE_CAP_MAX_PAYLOAD_SIZE(x)	((x) << 5)
> +#define PCIE_CAP_MAX_READ_REQ_MASK	GENMASK(14, 12)
> +#define PCIE_CAP_MAX_READ_REQ_SIZE(x)	((x) << 12)
> +
> +#define PCI_CLASS_REVISION_MASK		GENMASK(7, 0)

And the reason for not using standard PCI register macros is ?

> +/* PCIe specific config registers */
> +#define PCIE_CFG0			0x0
> +#define APP_LTSSM_ENABLE		BIT(7)
> +
> +#define PCIE_CFG_STATUS12		0x30
> +#define IS_SMLH_LINK_UP(x)		((x) & (1 << 6))
> +#define IS_RDLH_LINK_UP(x)		((x) & (1 << 16))
> +#define IS_LTSSM_UP(x)			((((x) >> 10) & 0x1f) == 0x11)
> +
> +#define PCIE_CFG_STATUS17		0x44
> +#define PM_CURRENT_STATE(x)		(((x) >> 7) & 0x1)
> +
> +#define WAIT_LINKUP_TIMEOUT		2000
> +#define PORT_CLK_RATE			100000000UL
> +#define MAX_PAYLOAD_SIZE		256
> +#define MAX_READ_REQ_SIZE		256
> +#define MESON_PCIE_PHY_POWERUP		0x1c
> +#define PCIE_RESET_DELAY		500
> +#define PCIE_SHARED_RESET		1
> +#define PCIE_NORMAL_RESET		0
> +
> +enum pcie_data_rate {
> +	PCIE_GEN1,
> +	PCIE_GEN2,
> +	PCIE_GEN3,
> +	PCIE_GEN4
> +};
> +
> +struct meson_pcie_mem_res {
> +	void __iomem *elbi_base; /* DT 0th resource */
> +	void __iomem *cfg_base; /* DT 1nd resource */
> +	void __iomem *phy_base; /* DT 2nd resource */
> +};

Nit: the /* DT *th resource */ comments are not really helpful, I would
remove them.

> +
> +struct meson_pcie_clk_res {
> +	struct clk *clk;
> +	struct clk *mipi_gate;
> +	struct clk *port_clk;
> +	struct clk *general_clk;
> +};
> +
> +struct meson_pcie_rc_reset {
> +	struct reset_control *phy;
> +	struct reset_control *port;
> +	struct reset_control *apb;
> +};
> +
> +struct meson_pcie {
> +	struct dw_pcie pci;
> +	struct meson_pcie_mem_res mem_res;
> +	struct meson_pcie_clk_res clk_res;
> +	struct meson_pcie_rc_reset mrst;
> +	struct gpio_desc *reset_gpio;
> +
> +	enum of_gpio_flags gpio_flag;
> +	int pcie_num;
> +	u32 port_num;
> +};
> +
> +static struct reset_control *meson_pcie_get_reset(struct meson_pcie *mp,
> +						  const char *id,
> +						  u32 reset_type)
> +{
> +	struct device *dev = mp->pci.dev;
> +	struct reset_control *reset;
> +
> +	if (reset_type == PCIE_SHARED_RESET)
> +		reset = devm_reset_control_get_shared(dev, id);
> +	else
> +		reset = devm_reset_control_get(dev, id);
> +
> +	return reset;
> +}
> +
> +static int meson_pcie_get_resets(struct meson_pcie *mp)
> +{
> +	struct meson_pcie_rc_reset *mrst = &mp->mrst;
> +
> +	mrst->phy = meson_pcie_get_reset(mp, "phy", PCIE_SHARED_RESET);
> +	if (IS_ERR(mrst->phy))
> +		return PTR_ERR(mrst->phy);
> +	reset_control_deassert(mrst->phy);
> +
> +	mrst->port = meson_pcie_get_reset(mp, "port", PCIE_NORMAL_RESET);
> +	if (IS_ERR(mrst->port))
> +		return PTR_ERR(mrst->port);
> +	reset_control_deassert(mrst->port);
> +
> +	mrst->apb = meson_pcie_get_reset(mp, "apb", PCIE_SHARED_RESET);
> +	if (IS_ERR(mrst->apb))
> +		return PTR_ERR(mrst->apb);
> +	reset_control_deassert(mrst->apb);
> +
> +	return 0;
> +}
> +
> +static void __iomem *meson_pcie_get_mem(struct platform_device *pdev,
> +					struct meson_pcie *mp,
> +					const char *id)
> +{
> +	struct device *dev = mp->pci.dev;
> +	struct resource *res;
> +
> +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, id);
> +
> +	return devm_ioremap_resource(dev, res);
> +}
> +
> +static void __iomem *meson_pcie_get_mem_shared(struct platform_device *pdev,
> +					       struct meson_pcie *mp,
> +					       const char *id)
> +{
> +	struct device *dev = mp->pci.dev;
> +	struct resource *res;
> +
> +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, id);
> +	if (!res) {
> +		dev_err(dev, "No REG resource %s\n", id);
> +		return (void *)-ENXIO;

		return ERR_PTR(-ENXIO);

> +	}
> +
> +	return devm_ioremap(dev, res->start, resource_size(res));
> +}
> +
> +static int meson_pcie_get_mems(struct platform_device *pdev,
> +			       struct meson_pcie *mp)
> +{
> +	mp->mem_res.elbi_base = meson_pcie_get_mem(pdev, mp, "elbi");
> +	if (IS_ERR(mp->mem_res.elbi_base))
> +		return PTR_ERR(mp->mem_res.elbi_base);
> +
> +	mp->mem_res.cfg_base = meson_pcie_get_mem(pdev, mp, "cfg");
> +	if (IS_ERR(mp->mem_res.cfg_base))
> +		return PTR_ERR(mp->mem_res.cfg_base);
> +
> +	/* Meson SoC has two PCI controllers use same phy register*/
> +	mp->mem_res.phy_base = meson_pcie_get_mem_shared(pdev, mp, "phy");
> +	if (IS_ERR(mp->mem_res.phy_base))
> +		return PTR_ERR(mp->mem_res.phy_base);
> +
> +	return 0;
> +}
> +
> +static void meson_pcie_power_on(struct meson_pcie *mp)
> +{
> +	writel(MESON_PCIE_PHY_POWERUP, mp->mem_res.phy_base);
> +}
> +
> +static void meson_pcie_reset(struct meson_pcie *mp)
> +{
> +	struct meson_pcie_rc_reset *mrst = &mp->mrst;
> +
> +	reset_control_assert(mrst->phy);
> +	udelay(PCIE_RESET_DELAY);
> +	reset_control_deassert(mrst->phy);
> +	udelay(PCIE_RESET_DELAY);
> +
> +	reset_control_assert(mrst->port);
> +	reset_control_assert(mrst->apb);
> +	udelay(PCIE_RESET_DELAY);
> +	reset_control_deassert(mrst->port);
> +	reset_control_deassert(mrst->apb);
> +	udelay(PCIE_RESET_DELAY);
> +}
> +
> +static inline struct clk *meson_pcie_probe_clock(struct device *dev,
> +						 const char *id, u64 rate)
> +{
> +	struct clk *clk;
> +	int ret;
> +
> +	clk = devm_clk_get(dev, id);
> +	if (IS_ERR(clk))
> +		return clk;
> +
> +	if (rate) {
> +		ret = clk_set_rate(clk, rate);
> +		if (ret) {
> +			dev_err(dev, "set clk rate failed, ret = %d\n", ret);
> +			return ERR_PTR(ret);
> +		}
> +	}
> +
> +	ret = clk_prepare_enable(clk);
> +	if (ret) {
> +		dev_err(dev, "couldn't enable clk\n");
> +		return ERR_PTR(ret);
> +	}
> +
> +	devm_add_action_or_reset(dev,
> +				 (void (*) (void *))clk_disable_unprepare,
> +				 clk);
> +
> +	return clk;
> +}
> +
> +static int meson_pcie_probe_clocks(struct meson_pcie *mp)
> +{
> +	struct device *dev = mp->pci.dev;
> +	struct meson_pcie_clk_res *res = &mp->clk_res;
> +
> +	res->port_clk = meson_pcie_probe_clock(dev, "port", PORT_CLK_RATE);
> +	if (IS_ERR(res->port_clk))
> +		return PTR_ERR(res->port_clk);
> +
> +	res->mipi_gate = meson_pcie_probe_clock(dev, "pcie_mipi_en", 0);
> +	if (IS_ERR(res->mipi_gate))
> +		return PTR_ERR(res->mipi_gate);
> +
> +	res->general_clk = meson_pcie_probe_clock(dev, "pcie_general", 0);
> +	if (IS_ERR(res->general_clk))
> +		return PTR_ERR(res->general_clk);
> +
> +	res->clk = meson_pcie_probe_clock(dev, "pcie", 0);
> +	if (IS_ERR(res->clk))
> +		return PTR_ERR(res->clk);
> +
> +	return 0;
> +}
> +
> +static inline void meson_elb_writel(struct meson_pcie *mp, u32 val, u32 reg)
> +{
> +	writel(val, mp->mem_res.elbi_base + reg);
> +}
> +
> +static inline u32 meson_elb_readl(struct meson_pcie *mp, u32 reg)
> +{
> +	return readl(mp->mem_res.elbi_base + reg);
> +}
> +
> +static inline u32 meson_cfg_readl(struct meson_pcie *mp, u32 reg)
> +{
> +	return readl(mp->mem_res.cfg_base + reg);
> +}
> +
> +static inline void meson_cfg_writel(struct meson_pcie *mp, u32 val, u32 reg)
> +{
> +	writel(val, mp->mem_res.cfg_base + reg);
> +}
> +
> +static void meson_pcie_assert_reset(struct meson_pcie *mp)
> +{
> +	gpiod_set_value_cansleep(mp->reset_gpio, 0);
> +	udelay(500);
> +	gpiod_set_value_cansleep(mp->reset_gpio, 1);
> +}
> +
> +static void meson_pcie_init_dw(struct meson_pcie *mp)
> +{
> +	u32 val;
> +
> +	val = meson_cfg_readl(mp, PCIE_CFG0);
> +	val |= APP_LTSSM_ENABLE;
> +	meson_cfg_writel(mp, val, PCIE_CFG0);
> +
> +	val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF);
> +	val &= ~LINK_CAPABLE_MASK;
> +	meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF);
> +
> +	val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF);
> +	val |= LINK_CAPABLE_X1 | FAST_LINK_MODE;
> +	meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF);
> +
> +	val = meson_elb_readl(mp, PCIE_GEN2_CTRL_OFF);
> +	val &= ~NUM_OF_LANES_MASK;
> +	meson_elb_writel(mp, val, PCIE_GEN2_CTRL_OFF);
> +
> +	val = meson_elb_readl(mp, PCIE_GEN2_CTRL_OFF);
> +	val |= NUM_OF_LANES_X1 | DIRECT_SPEED_CHANGE;
> +	meson_elb_writel(mp, val, PCIE_GEN2_CTRL_OFF);
> +
> +	meson_elb_writel(mp, 0x0, PCIE_BASE_ADDR0);
> +	meson_elb_writel(mp, 0x0, PCIE_BASE_ADDR1);
> +}
> +
> +static int meson_size_to_payload(struct meson_pcie *mp, int size)
> +{
> +	struct device *dev = mp->pci.dev;
> +
> +	/*
> +	 * dwc supports 2^(val+7) payload size, which val is 0~5 default to 1.
> +	 * So if input size is not 2^order alignment or less than 2^7 or bigger
> +	 * than 2^12, just set to default size 2^(1+7).
> +	 */
> +	if (size & (size - 1) || size < 128 || size > 4096) {

if (!is_power_of_2(size) || ..

> +		dev_warn(dev, "playload size %d, set to default 256\n", size);
> +		return 1;
> +	}
> +
> +	return fls(size) - 8;
> +}
> +
> +static void meson_set_max_payload(struct meson_pcie *mp, int size)
> +{
> +	u32 val = 0;
> +	int max_payload_size = meson_size_to_payload(mp, size);
> +
> +	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
> +	val &= ~PCIE_CAP_MAX_PAYLOAD_MASK;
> +	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
> +
> +	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
> +	val |= PCIE_CAP_MAX_PAYLOAD_SIZE(max_payload_size);
> +	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
> +}
> +
> +static void meson_set_max_rd_req_size(struct meson_pcie *mp, int size)
> +{
> +	u32 val;
> +	int max_rd_req_size = meson_size_to_payload(mp, size);
> +
> +	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
> +	val &= ~PCIE_CAP_MAX_READ_REQ_MASK;
> +	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
> +
> +	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
> +	val |= PCIE_CAP_MAX_READ_REQ_SIZE(max_rd_req_size);
> +	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
> +}
> +
> +static inline void meson_enable_memory_space(struct meson_pcie *mp)
> +{
> +	/* Set the RC Bus Master, Memory Space and I/O Space enables */
> +	meson_elb_writel(mp, PCI_IO_EN | PCI_MEM_SPACE_EN | PCI_BUS_MASTER_EN,
> +			 PCIE_STATUS_COMMAND);
> +}
> +
> +static int meson_pcie_establish_link(struct meson_pcie *mp)
> +{
> +	struct dw_pcie *pci = &mp->pci;
> +	struct pcie_port *pp = &pci->pp;
> +
> +	meson_pcie_init_dw(mp);
> +	meson_set_max_payload(mp, MAX_PAYLOAD_SIZE);
> +	meson_set_max_rd_req_size(mp, MAX_READ_REQ_SIZE);
> +
> +	dw_pcie_setup_rc(pp);
> +	meson_enable_memory_space(mp);
> +
> +	meson_pcie_assert_reset(mp);
> +
> +	return dw_pcie_wait_for_link(pci);
> +}
> +
> +static void meson_pcie_enable_interrupts(struct meson_pcie *mp)
> +{
> +	if (IS_ENABLED(CONFIG_PCI_MSI))
> +		dw_pcie_msi_init(&mp->pci.pp);
> +}
> +
> +static int meson_pcie_rd_own_conf(struct pcie_port *pp, int where, int size,
> +				  u32 *val)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +
> +	/* the device class is not reported correctly from the register */
> +	if (where == PCI_CLASS_REVISION) {
> +		*val = readl(pci->dbi_base + PCI_CLASS_REVISION);
> +		/* keep revision id */
> +		*val &= PCI_CLASS_REVISION_MASK;
> +		*val |= PCI_CLASS_BRIDGE_PCI << 16;
> +		return PCIBIOS_SUCCESSFUL;
> +	}

This seems broken and I do not understand why it is needed.

Code in dw_pcie_setup_rc() programmes the PCI_CLASS_DEVICE so I would
like to understand why you are "faking" it here.

Your approach seems broken if eg "where" is PCI_CLASS_DEVICE.

Lorenzo

> +
> +	return dw_pcie_read(pci->dbi_base + where, size, val);
> +}
> +
> +static int meson_pcie_wr_own_conf(struct pcie_port *pp, int where,
> +				  int size, u32 val)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +
> +	return dw_pcie_write(pci->dbi_base + where, size, val);
> +}
> +
> +static int meson_pcie_link_up(struct dw_pcie *pci)
> +{
> +	struct meson_pcie *mp = to_meson_pcie(pci);
> +	struct device *dev = pci->dev;
> +	u32 smlh_up = 0;
> +	u32 ltssm_up = 0;
> +	u32 rdlh_up = 0;
> +	u32 speed_okay = 0;
> +	u32 cnt = 0;
> +	u32 state12, state17;
> +
> +	while (smlh_up == 0 || rdlh_up == 0 || ltssm_up == 0 ||
> +	       speed_okay == 0) {
> +		udelay(20);
> +
> +		state12 = meson_cfg_readl(mp, PCIE_CFG_STATUS12);
> +		state17 = meson_cfg_readl(mp, PCIE_CFG_STATUS17);
> +		smlh_up = IS_SMLH_LINK_UP(state12);
> +		rdlh_up = IS_RDLH_LINK_UP(state12);
> +		ltssm_up = IS_LTSSM_UP(state12);
> +
> +		if (PM_CURRENT_STATE(state17) < PCIE_GEN3)
> +			speed_okay = 1;
> +
> +		if (smlh_up)
> +			dev_dbg(dev, "smlh_link_up is on\n");
> +		if (rdlh_up)
> +			dev_dbg(dev, "rdlh_link_up is on\n");
> +		if (ltssm_up)
> +			dev_dbg(dev, "ltssm_up is on\n");
> +		if (speed_okay)
> +			dev_dbg(dev, "speed_okay\n");
> +
> +		cnt++;
> +
> +		if (cnt >= WAIT_LINKUP_TIMEOUT) {
> +			dev_err(dev, "Error: Wait linkup timeout.\n");
> +			return 0;
> +		}
> +	}
> +
> +	return 1;
> +}
> +
> +static int meson_pcie_host_init(struct pcie_port *pp)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +	struct meson_pcie *mp = to_meson_pcie(pci);
> +	int ret;
> +
> +	ret = meson_pcie_establish_link(mp);
> +	if (ret)
> +		return ret;
> +
> +	meson_pcie_enable_interrupts(mp);
> +
> +	return 0;
> +}
> +
> +static const struct dw_pcie_host_ops meson_pcie_host_ops = {
> +	.rd_own_conf = meson_pcie_rd_own_conf,
> +	.wr_own_conf = meson_pcie_wr_own_conf,
> +	.host_init = meson_pcie_host_init,
> +};
> +
> +static int meson_add_pcie_port(struct meson_pcie *mp,
> +			       struct platform_device *pdev)
> +{
> +	struct dw_pcie *pci = &mp->pci;
> +	struct pcie_port *pp = &pci->pp;
> +	struct device *dev = &pdev->dev;
> +	int ret;
> +
> +	if (IS_ENABLED(CONFIG_PCI_MSI)) {
> +		pp->msi_irq = platform_get_irq(pdev, 0);
> +		if (pp->msi_irq < 0) {
> +			dev_err(dev, "failed to get msi irq\n");
> +			return pp->msi_irq;
> +		}
> +	}
> +
> +	pp->ops = &meson_pcie_host_ops;
> +	pci->dbi_base = mp->mem_res.elbi_base;
> +
> +	ret = dw_pcie_host_init(pp);
> +	if (ret) {
> +		dev_err(dev, "failed to initialize host\n");
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct dw_pcie_ops dw_pcie_ops = {
> +	.link_up = meson_pcie_link_up,
> +};
> +
> +static int meson_pcie_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct dw_pcie *pci;
> +	struct meson_pcie *mp;
> +	int ret;
> +
> +	mp = devm_kzalloc(dev, sizeof(*mp), GFP_KERNEL);
> +	if (!mp)
> +		return -ENOMEM;
> +
> +	pci = &mp->pci;
> +	pci->dev = dev;
> +	pci->ops = &dw_pcie_ops;
> +
> +	mp->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> +	if (IS_ERR(mp->reset_gpio)) {
> +		dev_err(dev, "Get reset gpio failed\n");
> +		return PTR_ERR(mp->reset_gpio);
> +	}
> +
> +	ret = meson_pcie_get_resets(mp);
> +	if (ret) {
> +		dev_err(dev, "Get reset resource failed, %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = meson_pcie_get_mems(pdev, mp);
> +	if (ret) {
> +		dev_err(dev, "Get memory resource failed, %d\n", ret);
> +		return ret;
> +	}
> +
> +	meson_pcie_power_on(mp);
> +	meson_pcie_reset(mp);
> +
> +	ret = meson_pcie_probe_clocks(mp);
> +	if (ret) {
> +		dev_err(dev, "Init clock resources failed, %d\n", ret);
> +		return ret;
> +	}
> +
> +	platform_set_drvdata(pdev, mp);
> +
> +	ret = meson_add_pcie_port(mp, pdev);
> +	if (ret < 0) {
> +		dev_err(dev, "Add PCIE port failed, %d\n", ret);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id meson_pcie_of_match[] = {
> +	{
> +		.compatible = "amlogic,axg-pcie",
> +	},
> +	{},
> +};
> +
> +static struct platform_driver meson_pcie_driver = {
> +	.probe = meson_pcie_probe,
> +	.driver = {
> +		.name = "meson-pcie",
> +		.of_match_table = meson_pcie_of_match,
> +	},
> +};
> +
> +builtin_platform_driver(meson_pcie_driver);
> -- 
> 2.7.4
>
Hanjie Lin Nov. 22, 2018, 2:41 a.m. | #2
On 2018/11/17 1:49, Lorenzo Pieralisi wrote:
> On Tue, Oct 09, 2018 at 09:53:10AM +0800, Hanjie Lin wrote:
>> From: Yue Wang <yue.wang@amlogic.com>
>>
>> The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
>> PCI core. This patch adds the driver support for Meson PCIe controller.
>>
>> Signed-off-by: Yue Wang <yue.wang@amlogic.com>
>> Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
>> ---
>>  MAINTAINERS                            |   7 +
>>  drivers/pci/controller/dwc/Kconfig     |  10 +
>>  drivers/pci/controller/dwc/Makefile    |   1 +
>>  drivers/pci/controller/dwc/pci-meson.c | 593 +++++++++++++++++++++++++++++++++
>>  4 files changed, 611 insertions(+)
>>  create mode 100644 drivers/pci/controller/dwc/pci-meson.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 02a3961..da579ef 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -11333,6 +11333,13 @@ L:	linux-pci@vger.kernel.org
>>  S:	Maintained
>>  F:	drivers/pci/controller/dwc/*spear*
>>  
>> +PCIE DRIVER FOR AMLOGIC MESON
> 
> Entries for PCIe host bridges are in alphabetical order, this one
> isn't so you should fix it.
> 

Yes, I will fix it.

>> +M:	Yue Wang <yue.wang@Amlogic.com>
>> +L:	linux-pci@vger.kernel.org
>> +L:	linux-amlogic@lists.infradead.org
>> +S:	Maintained
>> +F:	drivers/pci/controller/dwc/pci-meson.c
>> +
>>  PCMCIA SUBSYSTEM
>>  M:	Dominik Brodowski <linux@dominikbrodowski.net>
>>  T:	git git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia.git
>> diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
>> index 91b0194..7800322 100644
>> --- a/drivers/pci/controller/dwc/Kconfig
>> +++ b/drivers/pci/controller/dwc/Kconfig
>> @@ -193,4 +193,14 @@ config PCIE_HISI_STB
>>  	help
>>            Say Y here if you want PCIe controller support on HiSilicon STB SoCs
>>  
>> +config PCI_MESON
>> +	bool "MESON PCIe controller"
>> +	depends on PCI_MSI_IRQ_DOMAIN
>> +	select PCIE_DW_HOST
>> +	help
>> +	  Say Y here if you want to enable PCI controller support on Amlogic
>> +	  SoCs. The PCI controller on Amlogic is based on DesignWare hardware
>> +	  and therefore the driver re-uses the DesignWare core functions to
>> +	  implement the driver.
>> +
>>  endmenu
>> diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
>> index 5d2ce72..cf676bd 100644
>> --- a/drivers/pci/controller/dwc/Makefile
>> +++ b/drivers/pci/controller/dwc/Makefile
>> @@ -14,6 +14,7 @@ obj-$(CONFIG_PCIE_ARMADA_8K) += pcie-armada8k.o
>>  obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
>>  obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o
>>  obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
>> +obj-$(CONFIG_PCI_MESON) += pci-meson.o
>>  
>>  # The following drivers are for devices that use the generic ACPI
>>  # pci_root.c driver but don't support standard ECAM config access.
>> diff --git a/drivers/pci/controller/dwc/pci-meson.c b/drivers/pci/controller/dwc/pci-meson.c
>> new file mode 100644
>> index 0000000..2278b48
>> --- /dev/null
>> +++ b/drivers/pci/controller/dwc/pci-meson.c
>> @@ -0,0 +1,593 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * PCIe host controller driver for Amlogic MESON SoCs
>> + *
>> + * Copyright (c) 2018 Amlogic, inc.
>> + * Author: Yue Wang <yue.wang@amlogic.com>
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/of_device.h>
>> +#include <linux/of_gpio.h>
>> +#include <linux/pci.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/resource.h>
>> +#include <linux/types.h>
>> +#include <linux/reset.h>
>> +
>> +#include "pcie-designware.h"
>> +
>> +#define to_meson_pcie(x) dev_get_drvdata((x)->dev)
>> +
>> +/* External local bus interface registers */
>> +#define PLR_OFFSET			0x700
>> +#define PCIE_PORT_LINK_CTRL_OFF		(PLR_OFFSET + 0x10)
>> +#define FAST_LINK_MODE			BIT(7)
>> +#define LINK_CAPABLE_MASK		GENMASK(21, 16)
>> +#define LINK_CAPABLE_X1			BIT(16)
>> +
>> +#define PCIE_GEN2_CTRL_OFF		(PLR_OFFSET + 0x10c)
>> +#define NUM_OF_LANES_MASK		GENMASK(12, 8)
>> +#define NUM_OF_LANES_X1			BIT(8)
>> +#define DIRECT_SPEED_CHANGE		BIT(17)
>> +
>> +#define TYPE1_HDR_OFFSET		0x0
>> +#define PCIE_STATUS_COMMAND		(TYPE1_HDR_OFFSET + 0x04)
>> +#define PCI_IO_EN			BIT(0)
>> +#define PCI_MEM_SPACE_EN		BIT(1)
>> +#define PCI_BUS_MASTER_EN		BIT(2)
>> +#define PCIE_BASE_ADDR0			(TYPE1_HDR_OFFSET + 0x10)
>> +#define PCIE_BASE_ADDR1			(TYPE1_HDR_OFFSET + 0x14)
>> +
>> +#define PCIE_CAP_OFFSET			0x70
>> +#define PCIE_DEV_CTRL_DEV_STUS		(PCIE_CAP_OFFSET + 0x08)
>> +#define PCIE_CAP_MAX_PAYLOAD_MASK	GENMASK(7, 5)
>> +#define PCIE_CAP_MAX_PAYLOAD_SIZE(x)	((x) << 5)
>> +#define PCIE_CAP_MAX_READ_REQ_MASK	GENMASK(14, 12)
>> +#define PCIE_CAP_MAX_READ_REQ_SIZE(x)	((x) << 12)
>> +
>> +#define PCI_CLASS_REVISION_MASK		GENMASK(7, 0)
> 
> And the reason for not using standard PCI register macros is ?
> 

These registers macros are only used in MESON AXG PCIE driver.
It's a expression of MESON AXG datasheet and we can operate the register more easier. 


>> +/* PCIe specific config registers */
>> +#define PCIE_CFG0			0x0
>> +#define APP_LTSSM_ENABLE		BIT(7)
>> +
>> +#define PCIE_CFG_STATUS12		0x30
>> +#define IS_SMLH_LINK_UP(x)		((x) & (1 << 6))
>> +#define IS_RDLH_LINK_UP(x)		((x) & (1 << 16))
>> +#define IS_LTSSM_UP(x)			((((x) >> 10) & 0x1f) == 0x11)
>> +
>> +#define PCIE_CFG_STATUS17		0x44
>> +#define PM_CURRENT_STATE(x)		(((x) >> 7) & 0x1)
>> +
>> +#define WAIT_LINKUP_TIMEOUT		2000
>> +#define PORT_CLK_RATE			100000000UL
>> +#define MAX_PAYLOAD_SIZE		256
>> +#define MAX_READ_REQ_SIZE		256
>> +#define MESON_PCIE_PHY_POWERUP		0x1c
>> +#define PCIE_RESET_DELAY		500
>> +#define PCIE_SHARED_RESET		1
>> +#define PCIE_NORMAL_RESET		0
>> +
>> +enum pcie_data_rate {
>> +	PCIE_GEN1,
>> +	PCIE_GEN2,
>> +	PCIE_GEN3,
>> +	PCIE_GEN4
>> +};
>> +
>> +struct meson_pcie_mem_res {
>> +	void __iomem *elbi_base; /* DT 0th resource */
>> +	void __iomem *cfg_base; /* DT 1nd resource */
>> +	void __iomem *phy_base; /* DT 2nd resource */
>> +};
> 
> Nit: the /* DT *th resource */ comments are not really helpful, I would
> remove them.
> 

Ok, I'll remove them.

>> +
>> +struct meson_pcie_clk_res {
>> +	struct clk *clk;
>> +	struct clk *mipi_gate;
>> +	struct clk *port_clk;
>> +	struct clk *general_clk;
>> +};
>> +
>> +struct meson_pcie_rc_reset {
>> +	struct reset_control *phy;
>> +	struct reset_control *port;
>> +	struct reset_control *apb;
>> +};
>> +
>> +struct meson_pcie {
>> +	struct dw_pcie pci;
>> +	struct meson_pcie_mem_res mem_res;
>> +	struct meson_pcie_clk_res clk_res;
>> +	struct meson_pcie_rc_reset mrst;
>> +	struct gpio_desc *reset_gpio;
>> +
>> +	enum of_gpio_flags gpio_flag;
>> +	int pcie_num;
>> +	u32 port_num;
>> +};
>> +
>> +static struct reset_control *meson_pcie_get_reset(struct meson_pcie *mp,
>> +						  const char *id,
>> +						  u32 reset_type)
>> +{
>> +	struct device *dev = mp->pci.dev;
>> +	struct reset_control *reset;
>> +
>> +	if (reset_type == PCIE_SHARED_RESET)
>> +		reset = devm_reset_control_get_shared(dev, id);
>> +	else
>> +		reset = devm_reset_control_get(dev, id);
>> +
>> +	return reset;
>> +}
>> +
>> +static int meson_pcie_get_resets(struct meson_pcie *mp)
>> +{
>> +	struct meson_pcie_rc_reset *mrst = &mp->mrst;
>> +
>> +	mrst->phy = meson_pcie_get_reset(mp, "phy", PCIE_SHARED_RESET);
>> +	if (IS_ERR(mrst->phy))
>> +		return PTR_ERR(mrst->phy);
>> +	reset_control_deassert(mrst->phy);
>> +
>> +	mrst->port = meson_pcie_get_reset(mp, "port", PCIE_NORMAL_RESET);
>> +	if (IS_ERR(mrst->port))
>> +		return PTR_ERR(mrst->port);
>> +	reset_control_deassert(mrst->port);
>> +
>> +	mrst->apb = meson_pcie_get_reset(mp, "apb", PCIE_SHARED_RESET);
>> +	if (IS_ERR(mrst->apb))
>> +		return PTR_ERR(mrst->apb);
>> +	reset_control_deassert(mrst->apb);
>> +
>> +	return 0;
>> +}
>> +
>> +static void __iomem *meson_pcie_get_mem(struct platform_device *pdev,
>> +					struct meson_pcie *mp,
>> +					const char *id)
>> +{
>> +	struct device *dev = mp->pci.dev;
>> +	struct resource *res;
>> +
>> +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, id);
>> +
>> +	return devm_ioremap_resource(dev, res);
>> +}
>> +
>> +static void __iomem *meson_pcie_get_mem_shared(struct platform_device *pdev,
>> +					       struct meson_pcie *mp,
>> +					       const char *id)
>> +{
>> +	struct device *dev = mp->pci.dev;
>> +	struct resource *res;
>> +
>> +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, id);
>> +	if (!res) {
>> +		dev_err(dev, "No REG resource %s\n", id);
>> +		return (void *)-ENXIO;
> 
> 		return ERR_PTR(-ENXIO);

Yes, It's more standard and robust. I will fix it.

> 
>> +	}
>> +
>> +	return devm_ioremap(dev, res->start, resource_size(res));
>> +}
>> +
>> +static int meson_pcie_get_mems(struct platform_device *pdev,
>> +			       struct meson_pcie *mp)
>> +{
>> +	mp->mem_res.elbi_base = meson_pcie_get_mem(pdev, mp, "elbi");
>> +	if (IS_ERR(mp->mem_res.elbi_base))
>> +		return PTR_ERR(mp->mem_res.elbi_base);
>> +
>> +	mp->mem_res.cfg_base = meson_pcie_get_mem(pdev, mp, "cfg");
>> +	if (IS_ERR(mp->mem_res.cfg_base))
>> +		return PTR_ERR(mp->mem_res.cfg_base);
>> +
>> +	/* Meson SoC has two PCI controllers use same phy register*/
>> +	mp->mem_res.phy_base = meson_pcie_get_mem_shared(pdev, mp, "phy");
>> +	if (IS_ERR(mp->mem_res.phy_base))
>> +		return PTR_ERR(mp->mem_res.phy_base);
>> +
>> +	return 0;
>> +}
>> +
>> +static void meson_pcie_power_on(struct meson_pcie *mp)
>> +{
>> +	writel(MESON_PCIE_PHY_POWERUP, mp->mem_res.phy_base);
>> +}
>> +
>> +static void meson_pcie_reset(struct meson_pcie *mp)
>> +{
>> +	struct meson_pcie_rc_reset *mrst = &mp->mrst;
>> +
>> +	reset_control_assert(mrst->phy);
>> +	udelay(PCIE_RESET_DELAY);
>> +	reset_control_deassert(mrst->phy);
>> +	udelay(PCIE_RESET_DELAY);
>> +
>> +	reset_control_assert(mrst->port);
>> +	reset_control_assert(mrst->apb);
>> +	udelay(PCIE_RESET_DELAY);
>> +	reset_control_deassert(mrst->port);
>> +	reset_control_deassert(mrst->apb);
>> +	udelay(PCIE_RESET_DELAY);
>> +}
>> +
>> +static inline struct clk *meson_pcie_probe_clock(struct device *dev,
>> +						 const char *id, u64 rate)
>> +{
>> +	struct clk *clk;
>> +	int ret;
>> +
>> +	clk = devm_clk_get(dev, id);
>> +	if (IS_ERR(clk))
>> +		return clk;
>> +
>> +	if (rate) {
>> +		ret = clk_set_rate(clk, rate);
>> +		if (ret) {
>> +			dev_err(dev, "set clk rate failed, ret = %d\n", ret);
>> +			return ERR_PTR(ret);
>> +		}
>> +	}
>> +
>> +	ret = clk_prepare_enable(clk);
>> +	if (ret) {
>> +		dev_err(dev, "couldn't enable clk\n");
>> +		return ERR_PTR(ret);
>> +	}
>> +
>> +	devm_add_action_or_reset(dev,
>> +				 (void (*) (void *))clk_disable_unprepare,
>> +				 clk);
>> +
>> +	return clk;
>> +}
>> +
>> +static int meson_pcie_probe_clocks(struct meson_pcie *mp)
>> +{
>> +	struct device *dev = mp->pci.dev;
>> +	struct meson_pcie_clk_res *res = &mp->clk_res;
>> +
>> +	res->port_clk = meson_pcie_probe_clock(dev, "port", PORT_CLK_RATE);
>> +	if (IS_ERR(res->port_clk))
>> +		return PTR_ERR(res->port_clk);
>> +
>> +	res->mipi_gate = meson_pcie_probe_clock(dev, "pcie_mipi_en", 0);
>> +	if (IS_ERR(res->mipi_gate))
>> +		return PTR_ERR(res->mipi_gate);
>> +
>> +	res->general_clk = meson_pcie_probe_clock(dev, "pcie_general", 0);
>> +	if (IS_ERR(res->general_clk))
>> +		return PTR_ERR(res->general_clk);
>> +
>> +	res->clk = meson_pcie_probe_clock(dev, "pcie", 0);
>> +	if (IS_ERR(res->clk))
>> +		return PTR_ERR(res->clk);
>> +
>> +	return 0;
>> +}
>> +
>> +static inline void meson_elb_writel(struct meson_pcie *mp, u32 val, u32 reg)
>> +{
>> +	writel(val, mp->mem_res.elbi_base + reg);
>> +}
>> +
>> +static inline u32 meson_elb_readl(struct meson_pcie *mp, u32 reg)
>> +{
>> +	return readl(mp->mem_res.elbi_base + reg);
>> +}
>> +
>> +static inline u32 meson_cfg_readl(struct meson_pcie *mp, u32 reg)
>> +{
>> +	return readl(mp->mem_res.cfg_base + reg);
>> +}
>> +
>> +static inline void meson_cfg_writel(struct meson_pcie *mp, u32 val, u32 reg)
>> +{
>> +	writel(val, mp->mem_res.cfg_base + reg);
>> +}
>> +
>> +static void meson_pcie_assert_reset(struct meson_pcie *mp)
>> +{
>> +	gpiod_set_value_cansleep(mp->reset_gpio, 0);
>> +	udelay(500);
>> +	gpiod_set_value_cansleep(mp->reset_gpio, 1);
>> +}
>> +
>> +static void meson_pcie_init_dw(struct meson_pcie *mp)
>> +{
>> +	u32 val;
>> +
>> +	val = meson_cfg_readl(mp, PCIE_CFG0);
>> +	val |= APP_LTSSM_ENABLE;
>> +	meson_cfg_writel(mp, val, PCIE_CFG0);
>> +
>> +	val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF);
>> +	val &= ~LINK_CAPABLE_MASK;
>> +	meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF);
>> +
>> +	val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF);
>> +	val |= LINK_CAPABLE_X1 | FAST_LINK_MODE;
>> +	meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF);
>> +
>> +	val = meson_elb_readl(mp, PCIE_GEN2_CTRL_OFF);
>> +	val &= ~NUM_OF_LANES_MASK;
>> +	meson_elb_writel(mp, val, PCIE_GEN2_CTRL_OFF);
>> +
>> +	val = meson_elb_readl(mp, PCIE_GEN2_CTRL_OFF);
>> +	val |= NUM_OF_LANES_X1 | DIRECT_SPEED_CHANGE;
>> +	meson_elb_writel(mp, val, PCIE_GEN2_CTRL_OFF);
>> +
>> +	meson_elb_writel(mp, 0x0, PCIE_BASE_ADDR0);
>> +	meson_elb_writel(mp, 0x0, PCIE_BASE_ADDR1);
>> +}
>> +
>> +static int meson_size_to_payload(struct meson_pcie *mp, int size)
>> +{
>> +	struct device *dev = mp->pci.dev;
>> +
>> +	/*
>> +	 * dwc supports 2^(val+7) payload size, which val is 0~5 default to 1.
>> +	 * So if input size is not 2^order alignment or less than 2^7 or bigger
>> +	 * than 2^12, just set to default size 2^(1+7).
>> +	 */
>> +	if (size & (size - 1) || size < 128 || size > 4096) {
> 
> if (!is_power_of_2(size) || ..

Yes, it's more readable.

> 
>> +		dev_warn(dev, "playload size %d, set to default 256\n", size);
>> +		return 1;
>> +	}
>> +
>> +	return fls(size) - 8;
>> +}
>> +
>> +static void meson_set_max_payload(struct meson_pcie *mp, int size)
>> +{
>> +	u32 val = 0;
>> +	int max_payload_size = meson_size_to_payload(mp, size);
>> +
>> +	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
>> +	val &= ~PCIE_CAP_MAX_PAYLOAD_MASK;
>> +	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
>> +
>> +	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
>> +	val |= PCIE_CAP_MAX_PAYLOAD_SIZE(max_payload_size);
>> +	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
>> +}
>> +
>> +static void meson_set_max_rd_req_size(struct meson_pcie *mp, int size)
>> +{
>> +	u32 val;
>> +	int max_rd_req_size = meson_size_to_payload(mp, size);
>> +
>> +	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
>> +	val &= ~PCIE_CAP_MAX_READ_REQ_MASK;
>> +	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
>> +
>> +	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
>> +	val |= PCIE_CAP_MAX_READ_REQ_SIZE(max_rd_req_size);
>> +	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
>> +}
>> +
>> +static inline void meson_enable_memory_space(struct meson_pcie *mp)
>> +{
>> +	/* Set the RC Bus Master, Memory Space and I/O Space enables */
>> +	meson_elb_writel(mp, PCI_IO_EN | PCI_MEM_SPACE_EN | PCI_BUS_MASTER_EN,
>> +			 PCIE_STATUS_COMMAND);
>> +}
>> +
>> +static int meson_pcie_establish_link(struct meson_pcie *mp)
>> +{
>> +	struct dw_pcie *pci = &mp->pci;
>> +	struct pcie_port *pp = &pci->pp;
>> +
>> +	meson_pcie_init_dw(mp);
>> +	meson_set_max_payload(mp, MAX_PAYLOAD_SIZE);
>> +	meson_set_max_rd_req_size(mp, MAX_READ_REQ_SIZE);
>> +
>> +	dw_pcie_setup_rc(pp);
>> +	meson_enable_memory_space(mp);
>> +
>> +	meson_pcie_assert_reset(mp);
>> +
>> +	return dw_pcie_wait_for_link(pci);
>> +}
>> +
>> +static void meson_pcie_enable_interrupts(struct meson_pcie *mp)
>> +{
>> +	if (IS_ENABLED(CONFIG_PCI_MSI))
>> +		dw_pcie_msi_init(&mp->pci.pp);
>> +}
>> +
>> +static int meson_pcie_rd_own_conf(struct pcie_port *pp, int where, int size,
>> +				  u32 *val)
>> +{
>> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
>> +
>> +	/* the device class is not reported correctly from the register */
>> +	if (where == PCI_CLASS_REVISION) {
>> +		*val = readl(pci->dbi_base + PCI_CLASS_REVISION);
>> +		/* keep revision id */
>> +		*val &= PCI_CLASS_REVISION_MASK;
>> +		*val |= PCI_CLASS_BRIDGE_PCI << 16;
>> +		return PCIBIOS_SUCCESSFUL;
>> +	}
> 
> This seems broken and I do not understand why it is needed.
> 
> Code in dw_pcie_setup_rc() programmes the PCI_CLASS_DEVICE so I would
> like to understand why you are "faking" it here.
> 
> Your approach seems broken if eg "where" is PCI_CLASS_DEVICE.
> 
> Lorenzo
> 

Yes, it's a intended code when "where" is PCI_CLASS_DEVICE.
Because there is a bug of MESON AXG pcie contrller that software can not programe PCI_CLASS_DEVICE register,
so we must return a fake right value to ensure driver probe succesfully.
I'll add a comment for this.

Thanks.

>> +
>> +	return dw_pcie_read(pci->dbi_base + where, size, val);
>> +}
>> +
>> +static int meson_pcie_wr_own_conf(struct pcie_port *pp, int where,
>> +				  int size, u32 val)
>> +{
>> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
>> +
>> +	return dw_pcie_write(pci->dbi_base + where, size, val);
>> +}
>> +
>> +static int meson_pcie_link_up(struct dw_pcie *pci)
>> +{
>> +	struct meson_pcie *mp = to_meson_pcie(pci);
>> +	struct device *dev = pci->dev;
>> +	u32 smlh_up = 0;
>> +	u32 ltssm_up = 0;
>> +	u32 rdlh_up = 0;
>> +	u32 speed_okay = 0;
>> +	u32 cnt = 0;
>> +	u32 state12, state17;
>> +
>> +	while (smlh_up == 0 || rdlh_up == 0 || ltssm_up == 0 ||
>> +	       speed_okay == 0) {
>> +		udelay(20);
>> +
>> +		state12 = meson_cfg_readl(mp, PCIE_CFG_STATUS12);
>> +		state17 = meson_cfg_readl(mp, PCIE_CFG_STATUS17);
>> +		smlh_up = IS_SMLH_LINK_UP(state12);
>> +		rdlh_up = IS_RDLH_LINK_UP(state12);
>> +		ltssm_up = IS_LTSSM_UP(state12);
>> +
>> +		if (PM_CURRENT_STATE(state17) < PCIE_GEN3)
>> +			speed_okay = 1;
>> +
>> +		if (smlh_up)
>> +			dev_dbg(dev, "smlh_link_up is on\n");
>> +		if (rdlh_up)
>> +			dev_dbg(dev, "rdlh_link_up is on\n");
>> +		if (ltssm_up)
>> +			dev_dbg(dev, "ltssm_up is on\n");
>> +		if (speed_okay)
>> +			dev_dbg(dev, "speed_okay\n");
>> +
>> +		cnt++;
>> +
>> +		if (cnt >= WAIT_LINKUP_TIMEOUT) {
>> +			dev_err(dev, "Error: Wait linkup timeout.\n");
>> +			return 0;
>> +		}
>> +	}
>> +
>> +	return 1;
>> +}
>> +
>> +static int meson_pcie_host_init(struct pcie_port *pp)
>> +{
>> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
>> +	struct meson_pcie *mp = to_meson_pcie(pci);
>> +	int ret;
>> +
>> +	ret = meson_pcie_establish_link(mp);
>> +	if (ret)
>> +		return ret;
>> +
>> +	meson_pcie_enable_interrupts(mp);
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct dw_pcie_host_ops meson_pcie_host_ops = {
>> +	.rd_own_conf = meson_pcie_rd_own_conf,
>> +	.wr_own_conf = meson_pcie_wr_own_conf,
>> +	.host_init = meson_pcie_host_init,
>> +};
>> +
>> +static int meson_add_pcie_port(struct meson_pcie *mp,
>> +			       struct platform_device *pdev)
>> +{
>> +	struct dw_pcie *pci = &mp->pci;
>> +	struct pcie_port *pp = &pci->pp;
>> +	struct device *dev = &pdev->dev;
>> +	int ret;
>> +
>> +	if (IS_ENABLED(CONFIG_PCI_MSI)) {
>> +		pp->msi_irq = platform_get_irq(pdev, 0);
>> +		if (pp->msi_irq < 0) {
>> +			dev_err(dev, "failed to get msi irq\n");
>> +			return pp->msi_irq;
>> +		}
>> +	}
>> +
>> +	pp->ops = &meson_pcie_host_ops;
>> +	pci->dbi_base = mp->mem_res.elbi_base;
>> +
>> +	ret = dw_pcie_host_init(pp);
>> +	if (ret) {
>> +		dev_err(dev, "failed to initialize host\n");
>> +		return ret;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct dw_pcie_ops dw_pcie_ops = {
>> +	.link_up = meson_pcie_link_up,
>> +};
>> +
>> +static int meson_pcie_probe(struct platform_device *pdev)
>> +{
>> +	struct device *dev = &pdev->dev;
>> +	struct dw_pcie *pci;
>> +	struct meson_pcie *mp;
>> +	int ret;
>> +
>> +	mp = devm_kzalloc(dev, sizeof(*mp), GFP_KERNEL);
>> +	if (!mp)
>> +		return -ENOMEM;
>> +
>> +	pci = &mp->pci;
>> +	pci->dev = dev;
>> +	pci->ops = &dw_pcie_ops;
>> +
>> +	mp->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
>> +	if (IS_ERR(mp->reset_gpio)) {
>> +		dev_err(dev, "Get reset gpio failed\n");
>> +		return PTR_ERR(mp->reset_gpio);
>> +	}
>> +
>> +	ret = meson_pcie_get_resets(mp);
>> +	if (ret) {
>> +		dev_err(dev, "Get reset resource failed, %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	ret = meson_pcie_get_mems(pdev, mp);
>> +	if (ret) {
>> +		dev_err(dev, "Get memory resource failed, %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	meson_pcie_power_on(mp);
>> +	meson_pcie_reset(mp);
>> +
>> +	ret = meson_pcie_probe_clocks(mp);
>> +	if (ret) {
>> +		dev_err(dev, "Init clock resources failed, %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	platform_set_drvdata(pdev, mp);
>> +
>> +	ret = meson_add_pcie_port(mp, pdev);
>> +	if (ret < 0) {
>> +		dev_err(dev, "Add PCIE port failed, %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct of_device_id meson_pcie_of_match[] = {
>> +	{
>> +		.compatible = "amlogic,axg-pcie",
>> +	},
>> +	{},
>> +};
>> +
>> +static struct platform_driver meson_pcie_driver = {
>> +	.probe = meson_pcie_probe,
>> +	.driver = {
>> +		.name = "meson-pcie",
>> +		.of_match_table = meson_pcie_of_match,
>> +	},
>> +};
>> +
>> +builtin_platform_driver(meson_pcie_driver);
>> -- 
>> 2.7.4
>>
> 
> .
>

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 02a3961..da579ef 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11333,6 +11333,13 @@  L:	linux-pci@vger.kernel.org
 S:	Maintained
 F:	drivers/pci/controller/dwc/*spear*
 
+PCIE DRIVER FOR AMLOGIC MESON
+M:	Yue Wang <yue.wang@Amlogic.com>
+L:	linux-pci@vger.kernel.org
+L:	linux-amlogic@lists.infradead.org
+S:	Maintained
+F:	drivers/pci/controller/dwc/pci-meson.c
+
 PCMCIA SUBSYSTEM
 M:	Dominik Brodowski <linux@dominikbrodowski.net>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia.git
diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
index 91b0194..7800322 100644
--- a/drivers/pci/controller/dwc/Kconfig
+++ b/drivers/pci/controller/dwc/Kconfig
@@ -193,4 +193,14 @@  config PCIE_HISI_STB
 	help
           Say Y here if you want PCIe controller support on HiSilicon STB SoCs
 
+config PCI_MESON
+	bool "MESON PCIe controller"
+	depends on PCI_MSI_IRQ_DOMAIN
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want to enable PCI controller support on Amlogic
+	  SoCs. The PCI controller on Amlogic is based on DesignWare hardware
+	  and therefore the driver re-uses the DesignWare core functions to
+	  implement the driver.
+
 endmenu
diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
index 5d2ce72..cf676bd 100644
--- a/drivers/pci/controller/dwc/Makefile
+++ b/drivers/pci/controller/dwc/Makefile
@@ -14,6 +14,7 @@  obj-$(CONFIG_PCIE_ARMADA_8K) += pcie-armada8k.o
 obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
 obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o
 obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
+obj-$(CONFIG_PCI_MESON) += pci-meson.o
 
 # The following drivers are for devices that use the generic ACPI
 # pci_root.c driver but don't support standard ECAM config access.
diff --git a/drivers/pci/controller/dwc/pci-meson.c b/drivers/pci/controller/dwc/pci-meson.c
new file mode 100644
index 0000000..2278b48
--- /dev/null
+++ b/drivers/pci/controller/dwc/pci-meson.c
@@ -0,0 +1,593 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCIe host controller driver for Amlogic MESON SoCs
+ *
+ * Copyright (c) 2018 Amlogic, inc.
+ * Author: Yue Wang <yue.wang@amlogic.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/resource.h>
+#include <linux/types.h>
+#include <linux/reset.h>
+
+#include "pcie-designware.h"
+
+#define to_meson_pcie(x) dev_get_drvdata((x)->dev)
+
+/* External local bus interface registers */
+#define PLR_OFFSET			0x700
+#define PCIE_PORT_LINK_CTRL_OFF		(PLR_OFFSET + 0x10)
+#define FAST_LINK_MODE			BIT(7)
+#define LINK_CAPABLE_MASK		GENMASK(21, 16)
+#define LINK_CAPABLE_X1			BIT(16)
+
+#define PCIE_GEN2_CTRL_OFF		(PLR_OFFSET + 0x10c)
+#define NUM_OF_LANES_MASK		GENMASK(12, 8)
+#define NUM_OF_LANES_X1			BIT(8)
+#define DIRECT_SPEED_CHANGE		BIT(17)
+
+#define TYPE1_HDR_OFFSET		0x0
+#define PCIE_STATUS_COMMAND		(TYPE1_HDR_OFFSET + 0x04)
+#define PCI_IO_EN			BIT(0)
+#define PCI_MEM_SPACE_EN		BIT(1)
+#define PCI_BUS_MASTER_EN		BIT(2)
+
+#define PCIE_BASE_ADDR0			(TYPE1_HDR_OFFSET + 0x10)
+#define PCIE_BASE_ADDR1			(TYPE1_HDR_OFFSET + 0x14)
+
+#define PCIE_CAP_OFFSET			0x70
+#define PCIE_DEV_CTRL_DEV_STUS		(PCIE_CAP_OFFSET + 0x08)
+#define PCIE_CAP_MAX_PAYLOAD_MASK	GENMASK(7, 5)
+#define PCIE_CAP_MAX_PAYLOAD_SIZE(x)	((x) << 5)
+#define PCIE_CAP_MAX_READ_REQ_MASK	GENMASK(14, 12)
+#define PCIE_CAP_MAX_READ_REQ_SIZE(x)	((x) << 12)
+
+#define PCI_CLASS_REVISION_MASK		GENMASK(7, 0)
+
+/* PCIe specific config registers */
+#define PCIE_CFG0			0x0
+#define APP_LTSSM_ENABLE		BIT(7)
+
+#define PCIE_CFG_STATUS12		0x30
+#define IS_SMLH_LINK_UP(x)		((x) & (1 << 6))
+#define IS_RDLH_LINK_UP(x)		((x) & (1 << 16))
+#define IS_LTSSM_UP(x)			((((x) >> 10) & 0x1f) == 0x11)
+
+#define PCIE_CFG_STATUS17		0x44
+#define PM_CURRENT_STATE(x)		(((x) >> 7) & 0x1)
+
+#define WAIT_LINKUP_TIMEOUT		2000
+#define PORT_CLK_RATE			100000000UL
+#define MAX_PAYLOAD_SIZE		256
+#define MAX_READ_REQ_SIZE		256
+#define MESON_PCIE_PHY_POWERUP		0x1c
+#define PCIE_RESET_DELAY		500
+#define PCIE_SHARED_RESET		1
+#define PCIE_NORMAL_RESET		0
+
+enum pcie_data_rate {
+	PCIE_GEN1,
+	PCIE_GEN2,
+	PCIE_GEN3,
+	PCIE_GEN4
+};
+
+struct meson_pcie_mem_res {
+	void __iomem *elbi_base; /* DT 0th resource */
+	void __iomem *cfg_base; /* DT 1nd resource */
+	void __iomem *phy_base; /* DT 2nd resource */
+};
+
+struct meson_pcie_clk_res {
+	struct clk *clk;
+	struct clk *mipi_gate;
+	struct clk *port_clk;
+	struct clk *general_clk;
+};
+
+struct meson_pcie_rc_reset {
+	struct reset_control *phy;
+	struct reset_control *port;
+	struct reset_control *apb;
+};
+
+struct meson_pcie {
+	struct dw_pcie pci;
+	struct meson_pcie_mem_res mem_res;
+	struct meson_pcie_clk_res clk_res;
+	struct meson_pcie_rc_reset mrst;
+	struct gpio_desc *reset_gpio;
+
+	enum of_gpio_flags gpio_flag;
+	int pcie_num;
+	u32 port_num;
+};
+
+static struct reset_control *meson_pcie_get_reset(struct meson_pcie *mp,
+						  const char *id,
+						  u32 reset_type)
+{
+	struct device *dev = mp->pci.dev;
+	struct reset_control *reset;
+
+	if (reset_type == PCIE_SHARED_RESET)
+		reset = devm_reset_control_get_shared(dev, id);
+	else
+		reset = devm_reset_control_get(dev, id);
+
+	return reset;
+}
+
+static int meson_pcie_get_resets(struct meson_pcie *mp)
+{
+	struct meson_pcie_rc_reset *mrst = &mp->mrst;
+
+	mrst->phy = meson_pcie_get_reset(mp, "phy", PCIE_SHARED_RESET);
+	if (IS_ERR(mrst->phy))
+		return PTR_ERR(mrst->phy);
+	reset_control_deassert(mrst->phy);
+
+	mrst->port = meson_pcie_get_reset(mp, "port", PCIE_NORMAL_RESET);
+	if (IS_ERR(mrst->port))
+		return PTR_ERR(mrst->port);
+	reset_control_deassert(mrst->port);
+
+	mrst->apb = meson_pcie_get_reset(mp, "apb", PCIE_SHARED_RESET);
+	if (IS_ERR(mrst->apb))
+		return PTR_ERR(mrst->apb);
+	reset_control_deassert(mrst->apb);
+
+	return 0;
+}
+
+static void __iomem *meson_pcie_get_mem(struct platform_device *pdev,
+					struct meson_pcie *mp,
+					const char *id)
+{
+	struct device *dev = mp->pci.dev;
+	struct resource *res;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, id);
+
+	return devm_ioremap_resource(dev, res);
+}
+
+static void __iomem *meson_pcie_get_mem_shared(struct platform_device *pdev,
+					       struct meson_pcie *mp,
+					       const char *id)
+{
+	struct device *dev = mp->pci.dev;
+	struct resource *res;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, id);
+	if (!res) {
+		dev_err(dev, "No REG resource %s\n", id);
+		return (void *)-ENXIO;
+	}
+
+	return devm_ioremap(dev, res->start, resource_size(res));
+}
+
+static int meson_pcie_get_mems(struct platform_device *pdev,
+			       struct meson_pcie *mp)
+{
+	mp->mem_res.elbi_base = meson_pcie_get_mem(pdev, mp, "elbi");
+	if (IS_ERR(mp->mem_res.elbi_base))
+		return PTR_ERR(mp->mem_res.elbi_base);
+
+	mp->mem_res.cfg_base = meson_pcie_get_mem(pdev, mp, "cfg");
+	if (IS_ERR(mp->mem_res.cfg_base))
+		return PTR_ERR(mp->mem_res.cfg_base);
+
+	/* Meson SoC has two PCI controllers use same phy register*/
+	mp->mem_res.phy_base = meson_pcie_get_mem_shared(pdev, mp, "phy");
+	if (IS_ERR(mp->mem_res.phy_base))
+		return PTR_ERR(mp->mem_res.phy_base);
+
+	return 0;
+}
+
+static void meson_pcie_power_on(struct meson_pcie *mp)
+{
+	writel(MESON_PCIE_PHY_POWERUP, mp->mem_res.phy_base);
+}
+
+static void meson_pcie_reset(struct meson_pcie *mp)
+{
+	struct meson_pcie_rc_reset *mrst = &mp->mrst;
+
+	reset_control_assert(mrst->phy);
+	udelay(PCIE_RESET_DELAY);
+	reset_control_deassert(mrst->phy);
+	udelay(PCIE_RESET_DELAY);
+
+	reset_control_assert(mrst->port);
+	reset_control_assert(mrst->apb);
+	udelay(PCIE_RESET_DELAY);
+	reset_control_deassert(mrst->port);
+	reset_control_deassert(mrst->apb);
+	udelay(PCIE_RESET_DELAY);
+}
+
+static inline struct clk *meson_pcie_probe_clock(struct device *dev,
+						 const char *id, u64 rate)
+{
+	struct clk *clk;
+	int ret;
+
+	clk = devm_clk_get(dev, id);
+	if (IS_ERR(clk))
+		return clk;
+
+	if (rate) {
+		ret = clk_set_rate(clk, rate);
+		if (ret) {
+			dev_err(dev, "set clk rate failed, ret = %d\n", ret);
+			return ERR_PTR(ret);
+		}
+	}
+
+	ret = clk_prepare_enable(clk);
+	if (ret) {
+		dev_err(dev, "couldn't enable clk\n");
+		return ERR_PTR(ret);
+	}
+
+	devm_add_action_or_reset(dev,
+				 (void (*) (void *))clk_disable_unprepare,
+				 clk);
+
+	return clk;
+}
+
+static int meson_pcie_probe_clocks(struct meson_pcie *mp)
+{
+	struct device *dev = mp->pci.dev;
+	struct meson_pcie_clk_res *res = &mp->clk_res;
+
+	res->port_clk = meson_pcie_probe_clock(dev, "port", PORT_CLK_RATE);
+	if (IS_ERR(res->port_clk))
+		return PTR_ERR(res->port_clk);
+
+	res->mipi_gate = meson_pcie_probe_clock(dev, "pcie_mipi_en", 0);
+	if (IS_ERR(res->mipi_gate))
+		return PTR_ERR(res->mipi_gate);
+
+	res->general_clk = meson_pcie_probe_clock(dev, "pcie_general", 0);
+	if (IS_ERR(res->general_clk))
+		return PTR_ERR(res->general_clk);
+
+	res->clk = meson_pcie_probe_clock(dev, "pcie", 0);
+	if (IS_ERR(res->clk))
+		return PTR_ERR(res->clk);
+
+	return 0;
+}
+
+static inline void meson_elb_writel(struct meson_pcie *mp, u32 val, u32 reg)
+{
+	writel(val, mp->mem_res.elbi_base + reg);
+}
+
+static inline u32 meson_elb_readl(struct meson_pcie *mp, u32 reg)
+{
+	return readl(mp->mem_res.elbi_base + reg);
+}
+
+static inline u32 meson_cfg_readl(struct meson_pcie *mp, u32 reg)
+{
+	return readl(mp->mem_res.cfg_base + reg);
+}
+
+static inline void meson_cfg_writel(struct meson_pcie *mp, u32 val, u32 reg)
+{
+	writel(val, mp->mem_res.cfg_base + reg);
+}
+
+static void meson_pcie_assert_reset(struct meson_pcie *mp)
+{
+	gpiod_set_value_cansleep(mp->reset_gpio, 0);
+	udelay(500);
+	gpiod_set_value_cansleep(mp->reset_gpio, 1);
+}
+
+static void meson_pcie_init_dw(struct meson_pcie *mp)
+{
+	u32 val;
+
+	val = meson_cfg_readl(mp, PCIE_CFG0);
+	val |= APP_LTSSM_ENABLE;
+	meson_cfg_writel(mp, val, PCIE_CFG0);
+
+	val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF);
+	val &= ~LINK_CAPABLE_MASK;
+	meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF);
+
+	val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF);
+	val |= LINK_CAPABLE_X1 | FAST_LINK_MODE;
+	meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF);
+
+	val = meson_elb_readl(mp, PCIE_GEN2_CTRL_OFF);
+	val &= ~NUM_OF_LANES_MASK;
+	meson_elb_writel(mp, val, PCIE_GEN2_CTRL_OFF);
+
+	val = meson_elb_readl(mp, PCIE_GEN2_CTRL_OFF);
+	val |= NUM_OF_LANES_X1 | DIRECT_SPEED_CHANGE;
+	meson_elb_writel(mp, val, PCIE_GEN2_CTRL_OFF);
+
+	meson_elb_writel(mp, 0x0, PCIE_BASE_ADDR0);
+	meson_elb_writel(mp, 0x0, PCIE_BASE_ADDR1);
+}
+
+static int meson_size_to_payload(struct meson_pcie *mp, int size)
+{
+	struct device *dev = mp->pci.dev;
+
+	/*
+	 * dwc supports 2^(val+7) payload size, which val is 0~5 default to 1.
+	 * So if input size is not 2^order alignment or less than 2^7 or bigger
+	 * than 2^12, just set to default size 2^(1+7).
+	 */
+	if (size & (size - 1) || size < 128 || size > 4096) {
+		dev_warn(dev, "playload size %d, set to default 256\n", size);
+		return 1;
+	}
+
+	return fls(size) - 8;
+}
+
+static void meson_set_max_payload(struct meson_pcie *mp, int size)
+{
+	u32 val = 0;
+	int max_payload_size = meson_size_to_payload(mp, size);
+
+	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
+	val &= ~PCIE_CAP_MAX_PAYLOAD_MASK;
+	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
+
+	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
+	val |= PCIE_CAP_MAX_PAYLOAD_SIZE(max_payload_size);
+	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
+}
+
+static void meson_set_max_rd_req_size(struct meson_pcie *mp, int size)
+{
+	u32 val;
+	int max_rd_req_size = meson_size_to_payload(mp, size);
+
+	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
+	val &= ~PCIE_CAP_MAX_READ_REQ_MASK;
+	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
+
+	val = meson_elb_readl(mp, PCIE_DEV_CTRL_DEV_STUS);
+	val |= PCIE_CAP_MAX_READ_REQ_SIZE(max_rd_req_size);
+	meson_elb_writel(mp, val, PCIE_DEV_CTRL_DEV_STUS);
+}
+
+static inline void meson_enable_memory_space(struct meson_pcie *mp)
+{
+	/* Set the RC Bus Master, Memory Space and I/O Space enables */
+	meson_elb_writel(mp, PCI_IO_EN | PCI_MEM_SPACE_EN | PCI_BUS_MASTER_EN,
+			 PCIE_STATUS_COMMAND);
+}
+
+static int meson_pcie_establish_link(struct meson_pcie *mp)
+{
+	struct dw_pcie *pci = &mp->pci;
+	struct pcie_port *pp = &pci->pp;
+
+	meson_pcie_init_dw(mp);
+	meson_set_max_payload(mp, MAX_PAYLOAD_SIZE);
+	meson_set_max_rd_req_size(mp, MAX_READ_REQ_SIZE);
+
+	dw_pcie_setup_rc(pp);
+	meson_enable_memory_space(mp);
+
+	meson_pcie_assert_reset(mp);
+
+	return dw_pcie_wait_for_link(pci);
+}
+
+static void meson_pcie_enable_interrupts(struct meson_pcie *mp)
+{
+	if (IS_ENABLED(CONFIG_PCI_MSI))
+		dw_pcie_msi_init(&mp->pci.pp);
+}
+
+static int meson_pcie_rd_own_conf(struct pcie_port *pp, int where, int size,
+				  u32 *val)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+
+	/* the device class is not reported correctly from the register */
+	if (where == PCI_CLASS_REVISION) {
+		*val = readl(pci->dbi_base + PCI_CLASS_REVISION);
+		/* keep revision id */
+		*val &= PCI_CLASS_REVISION_MASK;
+		*val |= PCI_CLASS_BRIDGE_PCI << 16;
+		return PCIBIOS_SUCCESSFUL;
+	}
+
+	return dw_pcie_read(pci->dbi_base + where, size, val);
+}
+
+static int meson_pcie_wr_own_conf(struct pcie_port *pp, int where,
+				  int size, u32 val)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+
+	return dw_pcie_write(pci->dbi_base + where, size, val);
+}
+
+static int meson_pcie_link_up(struct dw_pcie *pci)
+{
+	struct meson_pcie *mp = to_meson_pcie(pci);
+	struct device *dev = pci->dev;
+	u32 smlh_up = 0;
+	u32 ltssm_up = 0;
+	u32 rdlh_up = 0;
+	u32 speed_okay = 0;
+	u32 cnt = 0;
+	u32 state12, state17;
+
+	while (smlh_up == 0 || rdlh_up == 0 || ltssm_up == 0 ||
+	       speed_okay == 0) {
+		udelay(20);
+
+		state12 = meson_cfg_readl(mp, PCIE_CFG_STATUS12);
+		state17 = meson_cfg_readl(mp, PCIE_CFG_STATUS17);
+		smlh_up = IS_SMLH_LINK_UP(state12);
+		rdlh_up = IS_RDLH_LINK_UP(state12);
+		ltssm_up = IS_LTSSM_UP(state12);
+
+		if (PM_CURRENT_STATE(state17) < PCIE_GEN3)
+			speed_okay = 1;
+
+		if (smlh_up)
+			dev_dbg(dev, "smlh_link_up is on\n");
+		if (rdlh_up)
+			dev_dbg(dev, "rdlh_link_up is on\n");
+		if (ltssm_up)
+			dev_dbg(dev, "ltssm_up is on\n");
+		if (speed_okay)
+			dev_dbg(dev, "speed_okay\n");
+
+		cnt++;
+
+		if (cnt >= WAIT_LINKUP_TIMEOUT) {
+			dev_err(dev, "Error: Wait linkup timeout.\n");
+			return 0;
+		}
+	}
+
+	return 1;
+}
+
+static int meson_pcie_host_init(struct pcie_port *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct meson_pcie *mp = to_meson_pcie(pci);
+	int ret;
+
+	ret = meson_pcie_establish_link(mp);
+	if (ret)
+		return ret;
+
+	meson_pcie_enable_interrupts(mp);
+
+	return 0;
+}
+
+static const struct dw_pcie_host_ops meson_pcie_host_ops = {
+	.rd_own_conf = meson_pcie_rd_own_conf,
+	.wr_own_conf = meson_pcie_wr_own_conf,
+	.host_init = meson_pcie_host_init,
+};
+
+static int meson_add_pcie_port(struct meson_pcie *mp,
+			       struct platform_device *pdev)
+{
+	struct dw_pcie *pci = &mp->pci;
+	struct pcie_port *pp = &pci->pp;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		pp->msi_irq = platform_get_irq(pdev, 0);
+		if (pp->msi_irq < 0) {
+			dev_err(dev, "failed to get msi irq\n");
+			return pp->msi_irq;
+		}
+	}
+
+	pp->ops = &meson_pcie_host_ops;
+	pci->dbi_base = mp->mem_res.elbi_base;
+
+	ret = dw_pcie_host_init(pp);
+	if (ret) {
+		dev_err(dev, "failed to initialize host\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.link_up = meson_pcie_link_up,
+};
+
+static int meson_pcie_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct dw_pcie *pci;
+	struct meson_pcie *mp;
+	int ret;
+
+	mp = devm_kzalloc(dev, sizeof(*mp), GFP_KERNEL);
+	if (!mp)
+		return -ENOMEM;
+
+	pci = &mp->pci;
+	pci->dev = dev;
+	pci->ops = &dw_pcie_ops;
+
+	mp->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(mp->reset_gpio)) {
+		dev_err(dev, "Get reset gpio failed\n");
+		return PTR_ERR(mp->reset_gpio);
+	}
+
+	ret = meson_pcie_get_resets(mp);
+	if (ret) {
+		dev_err(dev, "Get reset resource failed, %d\n", ret);
+		return ret;
+	}
+
+	ret = meson_pcie_get_mems(pdev, mp);
+	if (ret) {
+		dev_err(dev, "Get memory resource failed, %d\n", ret);
+		return ret;
+	}
+
+	meson_pcie_power_on(mp);
+	meson_pcie_reset(mp);
+
+	ret = meson_pcie_probe_clocks(mp);
+	if (ret) {
+		dev_err(dev, "Init clock resources failed, %d\n", ret);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, mp);
+
+	ret = meson_add_pcie_port(mp, pdev);
+	if (ret < 0) {
+		dev_err(dev, "Add PCIE port failed, %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id meson_pcie_of_match[] = {
+	{
+		.compatible = "amlogic,axg-pcie",
+	},
+	{},
+};
+
+static struct platform_driver meson_pcie_driver = {
+	.probe = meson_pcie_probe,
+	.driver = {
+		.name = "meson-pcie",
+		.of_match_table = meson_pcie_of_match,
+	},
+};
+
+builtin_platform_driver(meson_pcie_driver);