[v3,3/5] dt-bindings: mfd: rk808: Add binding information for RK809 and RK817.
diff mbox series

Message ID 1535081441-20718-4-git-send-email-tony.xie@rock-chips.com
State Not Applicable
Headers show
Series
  • support a new type of PMIC, including two chips(rk817 and rk809)
Related show

Commit Message

Tony Xie Aug. 24, 2018, 3:30 a.m. UTC
Add device tree bindings documentation for Rockchip's RK809 & RK817 PMIC.

Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
---
 Documentation/devicetree/bindings/mfd/rk808.txt | 56 +++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

Comments

Rob Herring Aug. 28, 2018, 10:40 p.m. UTC | #1
On Fri, 24 Aug 2018 11:30:39 +0800, Tony Xie wrote:
> Add device tree bindings documentation for Rockchip's RK809 & RK817 PMIC.
> 
> Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
> ---
>  Documentation/devicetree/bindings/mfd/rk808.txt | 56 +++++++++++++++++++++++++
>  1 file changed, 56 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>
Lee Jones Sept. 11, 2018, 12:37 p.m. UTC | #2
On Fri, 24 Aug 2018, Tony Xie wrote:

> Add device tree bindings documentation for Rockchip's RK809 & RK817 PMIC.
> 
> Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
> ---
>  Documentation/devicetree/bindings/mfd/rk808.txt | 56 +++++++++++++++++++++++++
>  1 file changed, 56 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
> index 91b6522..c025a99 100644
> --- a/Documentation/devicetree/bindings/mfd/rk808.txt
> +++ b/Documentation/devicetree/bindings/mfd/rk808.txt
> @@ -3,11 +3,15 @@ RK8XX Power Management Integrated Circuit
>  The rk8xx family current members:
>  rk805
>  rk808
> +rk809
> +rk817
>  rk818
>  
>  Required properties:
>  - compatible: "rockchip,rk805"
>  - compatible: "rockchip,rk808"
> +- compatible: "rockchip,rk809"
> +- compatible: "rockchip,rk817"
>  - compatible: "rockchip,rk818"
>  - reg: I2C slave address
>  - interrupt-parent: The parent interrupt controller.
> @@ -46,6 +50,28 @@ Optional RK808 properties:
>    the gpio controller. If DVS GPIOs aren't present, voltage changes will happen
>    very quickly with no slow ramp time.
>  
> +Optional RK809 properties:
> +- vcc1-supply:  The input supply for DCDC_REG1
> +- vcc2-supply:  The input supply for DCDC_REG2
> +- vcc3-supply:  The input supply for DCDC_REG3
> +- vcc4-supply:  The input supply for DCDC_REG4
> +- vcc5-supply:  The input supply for LDO_REG1, LDO_REG2, LDO_REG3
> +- vcc6-supply:  The input supply for LDO_REG4, LDO_REG5, LDO_REG6
> +- vcc7-supply:  The input supply for LDO_REG7, LDO_REG8, LDO_REG9
> +- vcc8-supply:  The input supply for SWITCH_REG1
> +- vcc9-supply:  The input supply for DCDC_REG5, SWITCH_REG2
> +
> +Optional RK817 properties:
> +- vcc1-supply:  The input supply for DCDC_REG1
> +- vcc2-supply:  The input supply for DCDC_REG2
> +- vcc3-supply:  The input supply for DCDC_REG3
> +- vcc4-supply:  The input supply for DCDC_REG4
> +- vcc5-supply:  The input supply for LDO_REG1, LDO_REG2, LDO_REG3
> +- vcc6-supply:  The input supply for LDO_REG4, LDO_REG5, LDO_REG6
> +- vcc7-supply:  The input supply for LDO_REG7, LDO_REG8, LDO_REG9
> +- vcc8-supply:  The input supply for BOOST
> +- vcc9-supply:  The input supply for OTG_SWITCH

I think I'd like to see these squashed down a bit.

Something like:

> +Optional shared RK809 and RK817 properties:
> +- vcc1-supply:  The input supply for DCDC_REG1
> +- vcc2-supply:  The input supply for DCDC_REG2
> +- vcc3-supply:  The input supply for DCDC_REG3
> +- vcc4-supply:  The input supply for DCDC_REG4
> +- vcc5-supply:  The input supply for LDO_REG1, LDO_REG2, LDO_REG3
> +- vcc6-supply:  The input supply for LDO_REG4, LDO_REG5, LDO_REG6
> +- vcc7-supply:  The input supply for LDO_REG7, LDO_REG8, LDO_REG9
> +
> +Optional RK809 properties:
> +- vcc8-supply:  The input supply for SWITCH_REG1
> +- vcc9-supply:  The input supply for DCDC_REG5, SWITCH_REG2
> +
> +Optional RK817 properties:
> +- vcc8-supply:  The input supply for BOOST
> +- vcc9-supply:  The input supply for OTG_SWITCH

That's if 1-7 are as identical as they look at first glance.

>  Optional RK818 properties:
>  - vcc1-supply:  The input supply for DCDC_REG1
>  - vcc2-supply:  The input supply for DCDC_REG2
> @@ -87,6 +113,28 @@ number as described in RK808 datasheet.
>  	- SWITCH_REGn
>  		- valid values for n are 1 to 2
>  
> +Following regulators of the RK809 PMIC block are supported. Note that
> +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
> +number as described in RK808 datasheet.
> +
> +	- DCDC_REGn
> +		- valid values for n are 1 to 5.
> +	- LDO_REGn
> +		- valid values for n are 1 to 9.
> +	- SWITCH_REGn
> +		- valid values for n are 1 to 2.
> +
> +Following regulators of the RK817 PMIC block are supported. Note that
> +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
> +number as described in RK818 datasheet.

Is there any need to keep saying the same thing over and over?

Especially for something fairly obvious.

> +	- DCDC_REGn
> +		- valid values for n are 1 to 4.
> +	- LDO_REGn
> +		- valid values for n are 1 to 9.
> +	- BOOST
> +	- OTG_SWITCH
> +
>  Following regulators of the RK818 PMIC block are supported. Note that
>  the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
>  number as described in RK818 datasheet.
> @@ -99,6 +147,14 @@ number as described in RK818 datasheet.
>  	- HDMI_SWITCH
>  	- OTG_SWITCH
>  
> +There are three pins needed to config for each of RK809 and RK817,
> +named "gpio_ts" "gpio_gt" "gpio_slp".
> +	The gpio_gt and gpio_ts pins support the gpio function.
> +	The gpio_slp pin is for controlling the pmic states, as below:
> +		- reset
> +		- power down
> +		- sleep
> +
>  Standard regulator bindings are used inside regulator subnodes. Check
>    Documentation/devicetree/bindings/regulator/regulator.txt
>  for more details

Patch
diff mbox series

diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
index 91b6522..c025a99 100644
--- a/Documentation/devicetree/bindings/mfd/rk808.txt
+++ b/Documentation/devicetree/bindings/mfd/rk808.txt
@@ -3,11 +3,15 @@  RK8XX Power Management Integrated Circuit
 The rk8xx family current members:
 rk805
 rk808
+rk809
+rk817
 rk818
 
 Required properties:
 - compatible: "rockchip,rk805"
 - compatible: "rockchip,rk808"
+- compatible: "rockchip,rk809"
+- compatible: "rockchip,rk817"
 - compatible: "rockchip,rk818"
 - reg: I2C slave address
 - interrupt-parent: The parent interrupt controller.
@@ -46,6 +50,28 @@  Optional RK808 properties:
   the gpio controller. If DVS GPIOs aren't present, voltage changes will happen
   very quickly with no slow ramp time.
 
+Optional RK809 properties:
+- vcc1-supply:  The input supply for DCDC_REG1
+- vcc2-supply:  The input supply for DCDC_REG2
+- vcc3-supply:  The input supply for DCDC_REG3
+- vcc4-supply:  The input supply for DCDC_REG4
+- vcc5-supply:  The input supply for LDO_REG1, LDO_REG2, LDO_REG3
+- vcc6-supply:  The input supply for LDO_REG4, LDO_REG5, LDO_REG6
+- vcc7-supply:  The input supply for LDO_REG7, LDO_REG8, LDO_REG9
+- vcc8-supply:  The input supply for SWITCH_REG1
+- vcc9-supply:  The input supply for DCDC_REG5, SWITCH_REG2
+
+Optional RK817 properties:
+- vcc1-supply:  The input supply for DCDC_REG1
+- vcc2-supply:  The input supply for DCDC_REG2
+- vcc3-supply:  The input supply for DCDC_REG3
+- vcc4-supply:  The input supply for DCDC_REG4
+- vcc5-supply:  The input supply for LDO_REG1, LDO_REG2, LDO_REG3
+- vcc6-supply:  The input supply for LDO_REG4, LDO_REG5, LDO_REG6
+- vcc7-supply:  The input supply for LDO_REG7, LDO_REG8, LDO_REG9
+- vcc8-supply:  The input supply for BOOST
+- vcc9-supply:  The input supply for OTG_SWITCH
+
 Optional RK818 properties:
 - vcc1-supply:  The input supply for DCDC_REG1
 - vcc2-supply:  The input supply for DCDC_REG2
@@ -87,6 +113,28 @@  number as described in RK808 datasheet.
 	- SWITCH_REGn
 		- valid values for n are 1 to 2
 
+Following regulators of the RK809 PMIC block are supported. Note that
+the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
+number as described in RK808 datasheet.
+
+	- DCDC_REGn
+		- valid values for n are 1 to 5.
+	- LDO_REGn
+		- valid values for n are 1 to 9.
+	- SWITCH_REGn
+		- valid values for n are 1 to 2.
+
+Following regulators of the RK817 PMIC block are supported. Note that
+the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
+number as described in RK818 datasheet.
+
+	- DCDC_REGn
+		- valid values for n are 1 to 4.
+	- LDO_REGn
+		- valid values for n are 1 to 9.
+	- BOOST
+	- OTG_SWITCH
+
 Following regulators of the RK818 PMIC block are supported. Note that
 the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO
 number as described in RK818 datasheet.
@@ -99,6 +147,14 @@  number as described in RK818 datasheet.
 	- HDMI_SWITCH
 	- OTG_SWITCH
 
+There are three pins needed to config for each of RK809 and RK817,
+named "gpio_ts" "gpio_gt" "gpio_slp".
+	The gpio_gt and gpio_ts pins support the gpio function.
+	The gpio_slp pin is for controlling the pmic states, as below:
+		- reset
+		- power down
+		- sleep
+
 Standard regulator bindings are used inside regulator subnodes. Check
   Documentation/devicetree/bindings/regulator/regulator.txt
 for more details