[v7,04/13] mesh: use setup completion callback to complete mesh join

Message ID 1dfef1599c338815c6a599d3da7d37491d21eac8.1530660888.git.peter.oh@bowerswilkins.com
State New
Headers show
Series
  • mesh: enable DFS channels in mesh mode
Related show

Commit Message

Peter Oh July 3, 2018, 11:40 p.m.
From: Peter Oh <peter.oh@bowerswilkins.com>

mesh join function is the last function to be called during
mesh join process, but it's been called a bit earlier than
it's supposed to be, so that some mesh parameter values
such as VHT capabilities not applied correct when mesh join
is in process.
Moreover current design of mesh join that is called directly
after mesh initialization isn't suitable for DFS channels to use,
since mesh join process should be paused until DFS CAC is
done and resumed after it's done.
The callback will be called by hostapd_setup_interface_complete_sync.
There is possiblity that completing mesh init fails, so add error
handle codes.

Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
---
 src/ap/hostapd.c      | 11 ++++++++++-
 wpa_supplicant/mesh.c |  4 +++-
 2 files changed, 13 insertions(+), 2 deletions(-)

Patch

diff --git a/src/ap/hostapd.c b/src/ap/hostapd.c
index f095586..183e65a 100644
--- a/src/ap/hostapd.c
+++ b/src/ap/hostapd.c
@@ -355,6 +355,8 @@  static void hostapd_free_hapd_data(struct hostapd_data *hapd)
 #ifdef CONFIG_MESH
 	wpabuf_free(hapd->mesh_pending_auth);
 	hapd->mesh_pending_auth = NULL;
+	/* handling setup failure is already done */
+	hapd->setup_complete_cb = NULL;
 #endif /* CONFIG_MESH */
 
 	hostapd_clean_rrm(hapd);
@@ -2021,6 +2023,13 @@  dfs_offload:
 	if (hapd->setup_complete_cb)
 		hapd->setup_complete_cb(hapd->setup_complete_cb_ctx);
 
+#ifdef CONFIG_MESH
+	if (delay_apply_cfg && iface->mconf == NULL) {
+		wpa_printf(MSG_ERROR, "Error while completing mesh init");
+		goto fail;
+	}
+#endif /* CONFIG_MESH */
+
 	wpa_printf(MSG_DEBUG, "%s: Setup of interface done.",
 		   iface->bss[0]->conf->iface);
 	if (iface->interfaces && iface->interfaces->terminate_on_error > 0)
@@ -2164,7 +2173,7 @@  int hostapd_setup_interface(struct hostapd_iface *iface)
 	ret = setup_interface(iface);
 	if (ret) {
 		wpa_printf(MSG_ERROR, "%s: Unable to setup interface.",
-			   iface->bss[0]->conf->iface);
+			iface->conf ? iface->conf->bss[0]->iface : "N/A");
 		return -1;
 	}
 
diff --git a/wpa_supplicant/mesh.c b/wpa_supplicant/mesh.c
index 0740dc7..7b014b7 100644
--- a/wpa_supplicant/mesh.c
+++ b/wpa_supplicant/mesh.c
@@ -260,6 +260,7 @@  static int wpa_supplicant_mesh_init(struct wpa_supplicant *wpa_s,
 	if (!ifmsh)
 		return -ENOMEM;
 
+	ifmsh->owner = wpa_s;
 	ifmsh->drv_flags = wpa_s->drv_flags;
 	ifmsh->num_bss = 1;
 	ifmsh->bss = os_calloc(wpa_s->ifmsh->num_bss,
@@ -277,6 +278,8 @@  static int wpa_supplicant_mesh_init(struct wpa_supplicant *wpa_s,
 	bss->drv_priv = wpa_s->drv_priv;
 	bss->iface = ifmsh;
 	bss->mesh_sta_free_cb = mesh_mpm_free_sta;
+	bss->setup_complete_cb = wpas_mesh_complete_cb;
+	bss->setup_complete_cb_ctx = wpa_s;
 	frequency = ssid->frequency;
 	if (frequency != freq->freq &&
 	    frequency == freq->freq + freq->sec_channel_offset * 20) {
@@ -503,7 +506,6 @@  int wpa_supplicant_join_mesh(struct wpa_supplicant *wpa_s,
 		goto out;
 	}
 
-	wpas_mesh_complete_cb(wpa_s);
 out:
 	return ret;
 }