Patchwork [2/2] sparc32,leon: add GRPCI2 PCI Host driver

login
register
mail settings
Submitter Daniel Hellstrom
Date April 26, 2011, 8:54 a.m.
Message ID <1303808088-1231-2-git-send-email-daniel@gaisler.com>
Download mbox | patch
Permalink /patch/92895/
State Rejected
Delegated to: David Miller
Headers show

Comments

Daniel Hellstrom - April 26, 2011, 8:54 a.m.
The DMA region must be accessible in order for PCI peripheral
drivers to work, the sparc32 has DMA in the normal memory
zone which requires the GRPCI2 to PCI target BARs so that all
kernel low mem (192MB) can be mapped 1:1 to PCI address
space. The GRPCI2 has resizeable target BARs, by default the
first is made 256MB and all other BARs are disabled.

I/O space are always located on 0x1000-0x10000, but accessed
through the GRPCI2 PCI I/O Window memory mapped to virtual
address space.

Configuration space is accessed through the 64KB GRPCI2 PCI
CFG Window using LDA bypassing the MMU.

The GRPCI2 has a single PCI Window for prefetchable and non-
prefetchable address space, it is up to the AHB master
requesting PCI data to determine access type. Memory space
is mapped 1:1.

The GRPCI2 core can be configured in 4 different IRQ modes,
where PCI Interrupt, Error Interrupt and DMA Interrupt are
shared on a single IRQ line or at most 5 IRQs are used. The
GRPCI2 can mask/unmask PCI interrupts, Err and DMA in the control
and check status bits which tells us which IRQ really happended.
The GENIRQ layer is used to unmask/mask each individual IRQ
source by creating virtual IRQs and implementing a IRQ chip.

The optional DMA functionality of the GRPCI2 is not supported
by this patch.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
 arch/sparc/Kconfig                  |    7 +
 arch/sparc/include/asm/leon.h       |    3 +
 arch/sparc/kernel/Makefile          |    1 +
 arch/sparc/kernel/leon_kernel.c     |   15 +
 arch/sparc/kernel/leon_pci_grpci2.c |  905 +++++++++++++++++++++++++++++++++++
 5 files changed, 931 insertions(+), 0 deletions(-)
 create mode 100644 arch/sparc/kernel/leon_pci_grpci2.c

Patch

diff --git a/arch/sparc/Kconfig b/arch/sparc/Kconfig
index a56630d..59e0c72 100644
--- a/arch/sparc/Kconfig
+++ b/arch/sparc/Kconfig
@@ -537,6 +537,13 @@  config PCI_DOMAINS
 config PCI_SYSCALL
 	def_bool PCI
 
+config GRPCI2
+	bool "GRPCI2 Host Bridge Support"
+	depends on PCI && SPARC_LEON
+	default y
+	help
+	  Say Y here to include the GRPCI2 Host Bridge Driver.
+
 source "drivers/pci/Kconfig"
 
 source "drivers/pcmcia/Kconfig"
diff --git a/arch/sparc/include/asm/leon.h b/arch/sparc/include/asm/leon.h
index 31fb2ac..b921560 100644
--- a/arch/sparc/include/asm/leon.h
+++ b/arch/sparc/include/asm/leon.h
@@ -318,6 +318,9 @@  struct device_node;
 extern unsigned int leon_build_device_irq(unsigned int real_irq,
 					   irq_flow_handler_t flow_handler,
 					   const char *name, int do_ack);
+extern void leon_update_virq_handling(unsigned int virq,
+			      irq_flow_handler_t flow_handler,
+			      const char *name, int do_ack);
 extern void leon_clear_clock_irq(void);
 extern void leon_load_profile_irq(int cpu, unsigned int limit);
 extern void leon_init_timers(irq_handler_t counter_fn);
diff --git a/arch/sparc/kernel/Makefile b/arch/sparc/kernel/Makefile
index ea19bcc..1f771b2 100644
--- a/arch/sparc/kernel/Makefile
+++ b/arch/sparc/kernel/Makefile
@@ -78,6 +78,7 @@  obj-$(CONFIG_SPARC32_PCI) += pcic.o
 else
 obj-$(CONFIG_SPARC32_PCI) += leon_pci.o
 endif
+obj-$(CONFIG_GRPCI2)      += leon_pci_grpci2.o
 
 obj-$(CONFIG_SMP)         += trampoline_$(BITS).o smp_$(BITS).o
 obj-$(CONFIG_SPARC32_SMP) += sun4m_smp.o sun4d_smp.o leon_smp.o
diff --git a/arch/sparc/kernel/leon_kernel.c b/arch/sparc/kernel/leon_kernel.c
index 2f538ac..c23d61e 100644
--- a/arch/sparc/kernel/leon_kernel.c
+++ b/arch/sparc/kernel/leon_kernel.c
@@ -236,6 +236,21 @@  static unsigned int _leon_build_device_irq(struct platform_device *op,
 	return leon_build_device_irq(real_irq, handle_simple_irq, "edge", 0);
 }
 
+void leon_update_virq_handling(unsigned int virq,
+			      irq_flow_handler_t flow_handler,
+			      const char *name, int do_ack)
+{
+	unsigned long mask = (unsigned long)irq_get_chip_data(virq);
+
+	mask &= ~LEON_DO_ACK_HW;
+	if (do_ack)
+		mask |= LEON_DO_ACK_HW;
+
+	irq_set_chip_and_handler_name(virq, &leon_irq,
+				      flow_handler, name);
+	irq_set_chip_data(virq, (void *)mask);
+}
+
 void __init leon_init_timers(irq_handler_t counter_fn)
 {
 	int irq, eirq;
diff --git a/arch/sparc/kernel/leon_pci_grpci2.c b/arch/sparc/kernel/leon_pci_grpci2.c
new file mode 100644
index 0000000..8a0c501
--- /dev/null
+++ b/arch/sparc/kernel/leon_pci_grpci2.c
@@ -0,0 +1,905 @@ 
+/*
+ * leon_pci_grpci2.c: GRPCI2 Host PCI driver
+ *
+ * Copyright (C) 2011 Aeroflex Gaisler AB, Daniel Hellstrom
+ *
+ */
+
+#include <linux/of_device.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <asm/io.h>
+#include <asm/leon.h>
+#include <asm/vaddrs.h>
+#include <asm/sections.h>
+
+#include "irq.h"
+
+struct grpci2_barcfg {
+	unsigned long pciadr;	/* PCI Space Address */
+	unsigned long ahbadr;	/* PCI Base address mapped to this AHB addr */
+};
+
+/* Device Node Configuration options:
+ *  - barcfgs    : Custom Configuration of Host's 6 target BARs
+ *  - irq_mask   : Limit which PCI interrupts are enabled
+ *  - do_reset   : Force PCI Reset on startup
+ *
+ * barcfgs
+ * =======
+ *
+ * Optional custom Target BAR configuration (see struct grpci2_barcfg). All
+ * addresses are physical. Array always contains 6 elements (len=2*4*6 bytes)
+ *
+ * -1 means not configured (let host driver do default setup).
+ *
+ * [i*2+0] = PCI Address of BAR[i] on target interface
+ * [i*2+1] = Accessing PCI address of BAR[i] result in this AMBA address
+ *
+ *
+ * irq_mask
+ * ========
+ *
+ * Limit which PCI interrupts are enabled. 0=Disable, 1=Enable. By default
+ * all are enabled. Use this when PCI interrupt pins are floating on PCB.
+ * int, len=4.
+ *  bit0 = PCI INTA#
+ *  bit1 = PCI INTB#
+ *  bit2 = PCI INTC#
+ *  bit3 = PCI INTD#
+ *
+ *
+ * reset
+ * =====
+ *
+ * Force PCI reset on startup. int, len=4
+ */
+
+/* Enable Debugging Configuration Space Access */
+#undef GRPCI2_DEBUG_CFGACCESS
+
+/*
+ * GRPCI2 APB Register MAP
+ */
+struct grpci2_regs {
+	unsigned int ctrl;		/* 0x00 Control */
+	unsigned int sts_cap;		/* 0x04 Status / Capabilities */
+	int res1;			/* 0x08 */
+	unsigned int io_map;		/* 0x0C I/O Map address */
+	unsigned int dma_ctrl;		/* 0x10 DMA */
+	unsigned int dma_bdbase;	/* 0x14 DMA */
+	int res2[2];			/* 0x18 */
+	unsigned int bars[6];		/* 0x20 read-only PCI BARs */
+	int res3[2];			/* 0x38 */
+	unsigned int ahbmst_map[16];	/* 0x40 AHB->PCI Map per AHB Master */
+
+	/* PCI Trace Buffer Registers (OPTIONAL) */
+	unsigned int t_ctrl;		/* 0x80 */
+	unsigned int t_cnt;		/* 0x84 */
+	unsigned int t_adpat;		/* 0x88 */
+	unsigned int t_admask;		/* 0x8C */
+	unsigned int t_sigpat;		/* 0x90 */
+	unsigned int t_sigmask;		/* 0x94 */
+	unsigned int t_adstate;		/* 0x98 */
+	unsigned int t_sigstate;	/* 0x9C */
+};
+
+#define REGLOAD(a)	(be32_to_cpu(__raw_readl(&(a))))
+#define REGSTORE(a, v)	(__raw_writel(cpu_to_be32(v), &(a)))
+
+#define CTRL_BUS_BIT 16
+
+#define CTRL_RESET (1<<31)
+#define CTRL_SI (1<<27)
+#define CTRL_PE (1<<26)
+#define CTRL_EI (1<<25)
+#define CTRL_ER (1<<24)
+#define CTRL_BUS (0xff<<CTRL_BUS_BIT)
+#define CTRL_HOSTINT 0xf
+
+#define STS_HOST_BIT	31
+#define STS_MST_BIT	30
+#define STS_TAR_BIT	29
+#define STS_DMA_BIT	28
+#define STS_DI_BIT	27
+#define STS_HI_BIT	26
+#define STS_IRQMODE_BIT	24
+#define STS_TRACE_BIT	23
+#define STS_CFGERRVALID_BIT 20
+#define STS_CFGERR_BIT	19
+#define STS_INTTYPE_BIT	12
+#define STS_INTSTS_BIT	8
+#define STS_FDEPTH_BIT	2
+#define STS_FNUM_BIT	0
+
+#define STS_HOST	(1<<STS_HOST_BIT)
+#define STS_MST		(1<<STS_MST_BIT)
+#define STS_TAR		(1<<STS_TAR_BIT)
+#define STS_DMA		(1<<STS_DMA_BIT)
+#define STS_DI		(1<<STS_DI_BIT)
+#define STS_HI		(1<<STS_HI_BIT)
+#define STS_IRQMODE	(0x3<<STS_IRQMODE_BIT)
+#define STS_TRACE	(1<<STS_TRACE_BIT)
+#define STS_CFGERRVALID	(1<<STS_CFGERRVALID_BIT)
+#define STS_CFGERR	(1<<STS_CFGERR_BIT)
+#define STS_INTTYPE	(0x3f<<STS_INTTYPE_BIT)
+#define STS_INTSTS	(0xf<<STS_INTSTS_BIT)
+#define STS_FDEPTH	(0x7<<STS_FDEPTH_BIT)
+#define STS_FNUM	(0x3<<STS_FNUM_BIT)
+
+#define STS_ISYSERR	(1<<17)
+#define STS_IDMA	(1<<16)
+#define STS_IDMAERR	(1<<15)
+#define STS_IMSTABRT	(1<<14)
+#define STS_ITGTABRT	(1<<13)
+#define STS_IPARERR	(1<<12)
+
+#define STS_ERR_IRQ (STS_ISYSERR | STS_IMSTABRT | STS_ITGTABRT | STS_IPARERR)
+
+struct grpci2_bd_chan {
+	unsigned int ctrl;	/* 0x00 DMA Control */
+	unsigned int nchan;	/* 0x04 Next DMA Channel Address */
+	unsigned int nbd;	/* 0x08 Next Data Descriptor in chan */
+	unsigned int res;	/* 0x0C Reserved */
+};
+
+#define BD_CHAN_EN		0x80000000
+#define BD_CHAN_TYPE		0x00300000
+#define BD_CHAN_BDCNT		0x0000ffff
+#define BD_CHAN_EN_BIT		31
+#define BD_CHAN_TYPE_BIT	20
+#define BD_CHAN_BDCNT_BIT	0
+
+struct grpci2_bd_data {
+	unsigned int ctrl;	/* 0x00 DMA Data Control */
+	unsigned int pci_adr;	/* 0x04 PCI Start Address */
+	unsigned int ahb_adr;	/* 0x08 AHB Start address */
+	unsigned int next;	/* 0x0C Next Data Descriptor in chan */
+};
+
+#define BD_DATA_EN		0x80000000
+#define BD_DATA_IE		0x40000000
+#define BD_DATA_DR		0x20000000
+#define BD_DATA_TYPE		0x00300000
+#define BD_DATA_ER		0x00080000
+#define BD_DATA_LEN		0x0000ffff
+#define BD_DATA_EN_BIT		31
+#define BD_DATA_IE_BIT		30
+#define BD_DATA_DR_BIT		29
+#define BD_DATA_TYPE_BIT	20
+#define BD_DATA_ER_BIT		19
+#define BD_DATA_LEN_BIT		0
+
+/* GRPCI2 Capability */
+struct grpci2_cap_first {
+	unsigned int ctrl;
+	unsigned int pci2ahb_map[6];
+	unsigned int ext2ahb_map;
+	unsigned int io_map;
+	unsigned int pcibar_size[6];
+};
+#define CAP9_CTRL_OFS 0
+#define CAP9_BAR_OFS 0x4
+#define CAP9_IOMAP_OFS 0x20
+#define CAP9_BARSIZE_OFS 0x24
+
+struct grpci2_priv {
+	struct leon_pci_info	info; /* must be on top of this structure */
+	struct grpci2_regs	*regs;
+	char			irq;
+	char			irq_mode; /* IRQ Mode from CAPSTS REG */
+	char			bt_enabled;
+	char			do_reset;
+	char			irq_mask;
+	u32			pciid; /* PCI ID of Host */
+	unsigned char		irq_map[4];
+
+	/* Virtual IRQ numbers */
+	unsigned int		virq_err;
+	unsigned int		virq_dma;
+
+	/* AHB PCI Windows */
+	unsigned long		pci_area;	/* MEMORY */
+	unsigned long		pci_area_end;
+	unsigned long		pci_io;		/* I/O */
+	unsigned long		pci_conf;	/* CONFIGURATION */
+	unsigned long		pci_conf_end;
+	unsigned long		pci_io_va;
+
+	struct grpci2_barcfg	tgtbars[6];
+};
+
+DEFINE_SPINLOCK(grpci2_dev_lock);
+struct grpci2_priv *grpci2priv;
+
+int grpci2_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	struct grpci2_priv *priv = dev->bus->sysdata;
+	int irq_group;
+
+	/* Use default IRQ decoding on PCI BUS0 according slot numbering */
+	irq_group = slot & 0x3;
+	pin = ((pin - 1) + irq_group) & 0x3;
+
+	return priv->irq_map[pin];
+}
+
+void __devinit pcibios_update_irq(struct pci_dev *dev, int irq)
+{
+#ifdef CONFIG_PCI_DEBUG
+	printk(KERN_DEBUG "GRPCI2: Assigning IRQ %02d to %s\n", irq,
+		pci_name(dev));
+#endif
+	pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq);
+}
+
+static int grpci2_cfg_r32(struct grpci2_priv *priv, unsigned int bus,
+				unsigned int devfn, int where, u32 *val)
+{
+	unsigned int *pci_conf;
+	unsigned long flags;
+	u32 tmp;
+
+	if (where & 0x3)
+		return -EINVAL;
+
+	if (bus == 0 && PCI_SLOT(devfn) != 0)
+		devfn += (0x8 * 6);
+
+	/* Select bus */
+	spin_lock_irqsave(&grpci2_dev_lock, flags);
+	REGSTORE(priv->regs->ctrl, (REGLOAD(priv->regs->ctrl) & ~(0xff << 16)) |
+				   (bus << 16));
+	spin_unlock_irqrestore(&grpci2_dev_lock, flags);
+
+	/* clear old status */
+	REGSTORE(priv->regs->sts_cap, (STS_CFGERR | STS_CFGERRVALID));
+
+	pci_conf = (unsigned int *) (priv->pci_conf |
+						(devfn << 8) | (where & 0xfc));
+	tmp = LEON3_BYPASS_LOAD_PA(pci_conf);
+
+	/* Wait until GRPCI2 signals that CFG access is done, it should be
+	 * done instantaneously unless a DMA operation is ongoing...
+	 */
+	while ((REGLOAD(priv->regs->sts_cap) & STS_CFGERRVALID) == 0)
+		;
+
+	if (REGLOAD(priv->regs->sts_cap) & STS_CFGERR) {
+		*val = 0xffffffff;
+	} else {
+		/* Bus always little endian (unaffected by byte-swapping) */
+		*val = flip_dword(tmp);
+	}
+
+	return 0;
+}
+
+static int grpci2_cfg_r16(struct grpci2_priv *priv, unsigned int bus,
+				unsigned int devfn, int where, u32 *val)
+{
+	u32 v;
+	int ret;
+
+	if (where & 0x1)
+		return -EINVAL;
+	ret = grpci2_cfg_r32(priv, bus, devfn, where & ~0x3, &v);
+	*val = 0xffff & (v >> (8 * (where & 0x3)));
+	return ret;
+}
+
+static int grpci2_cfg_r8(struct grpci2_priv *priv, unsigned int bus,
+				unsigned int devfn, int where, u32 *val)
+{
+	u32 v;
+	int ret;
+
+	ret = grpci2_cfg_r32(priv, bus, devfn, where & ~0x3, &v);
+	*val = 0xff & (v >> (8 * (where & 3)));
+
+	return ret;
+}
+
+static int grpci2_cfg_w32(struct grpci2_priv *priv, unsigned int bus,
+				unsigned int devfn, int where, u32 val)
+{
+	unsigned int *pci_conf;
+	unsigned long flags;
+
+	if (where & 0x3)
+		return -EINVAL;
+
+	if (bus == 0 && PCI_SLOT(devfn) != 0)
+		devfn += (0x8 * 6);
+
+	/* Select bus */
+	spin_lock_irqsave(&grpci2_dev_lock, flags);
+	REGSTORE(priv->regs->ctrl, (REGLOAD(priv->regs->ctrl) & ~(0xff << 16)) |
+				   (bus << 16));
+	spin_unlock_irqrestore(&grpci2_dev_lock, flags);
+
+	/* clear old status */
+	REGSTORE(priv->regs->sts_cap, (STS_CFGERR | STS_CFGERRVALID));
+
+	pci_conf = (unsigned int *) (priv->pci_conf |
+						(devfn << 8) | (where & 0xfc));
+	LEON3_BYPASS_STORE_PA(pci_conf, flip_dword(val));
+
+	/* Wait until GRPCI2 signals that CFG access is done, it should be
+	 * done instantaneously unless a DMA operation is ongoing...
+	 */
+	while ((REGLOAD(priv->regs->sts_cap) & STS_CFGERRVALID) == 0)
+		;
+
+	return 0;
+}
+
+static int grpci2_cfg_w16(struct grpci2_priv *priv, unsigned int bus,
+				unsigned int devfn, int where, u32 val)
+{
+	int ret;
+	u32 v;
+
+	if (where & 0x1)
+		return -EINVAL;
+	ret = grpci2_cfg_r32(priv, bus, devfn, where&~3, &v);
+	if (ret)
+		return ret;
+	v = (v & ~(0xffff << (8 * (where & 0x3)))) |
+	    ((0xffff & val) << (8 * (where & 0x3)));
+	return grpci2_cfg_w32(priv, bus, devfn, where & ~0x3, v);
+}
+
+static int grpci2_cfg_w8(struct grpci2_priv *priv, unsigned int bus,
+				unsigned int devfn, int where, u32 val)
+{
+	int ret;
+	u32 v;
+
+	ret = grpci2_cfg_r32(priv, bus, devfn, where & ~0x3, &v);
+	if (ret != 0)
+		return ret;
+	v = (v & ~(0xff << (8 * (where & 0x3)))) |
+	    ((0xff & val) << (8 * (where & 0x3)));
+	return grpci2_cfg_w32(priv, bus, devfn, where & ~0x3, v);
+}
+
+/* Read from Configuration Space. When entering here the PCI layer has taken
+ * the pci_lock spinlock and IRQ is off.
+ */
+static int grpci2_read_config(struct pci_bus *bus, unsigned int devfn,
+			      int where, int size, u32 *val)
+{
+	struct grpci2_priv *priv = grpci2priv;
+	unsigned int busno = bus->number;
+	int ret;
+
+	if (PCI_SLOT(devfn) > 15 || (PCI_SLOT(devfn) == 0 && busno == 0)) {
+		*val = ~0;
+		return 0;
+	}
+
+	switch (size) {
+	case 1:
+		ret = grpci2_cfg_r8(priv, busno, devfn, where, val);
+		break;
+	case 2:
+		ret = grpci2_cfg_r16(priv, busno, devfn, where, val);
+		break;
+	case 4:
+		ret = grpci2_cfg_r32(priv, busno, devfn, where, val);
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+#ifdef GRPCI2_DEBUG_CFGACCESS
+	printk(KERN_INFO "grpci2_read_config: [%02x:%02x:%x] ofs=%d val=%x "
+		"size=%d\n", busno, PCI_SLOT(devfn), PCI_FUNC(devfn), where,
+		*val, size);
+#endif
+
+	return ret;
+}
+
+/* Write to Configuration Space. When entering here the PCI layer has taken
+ * the pci_lock spinlock and IRQ is off.
+ */
+static int grpci2_write_config(struct pci_bus *bus, unsigned int devfn,
+			       int where, int size, u32 val)
+{
+	struct grpci2_priv *priv = grpci2priv;
+	unsigned int busno = bus->number;
+
+	if (PCI_SLOT(devfn) > 15 || (PCI_SLOT(devfn) == 0 && busno == 0))
+		return 0;
+
+#ifdef GRPCI2_DEBUG_CFGACCESS
+	printk(KERN_INFO "grpci2_write_config: [%02x:%02x:%x] ofs=%d size=%d "
+		"val=%x\n", busno, PCI_SLOT(devfn), PCI_FUNC(devfn),
+		where, size, val);
+#endif
+
+	switch (size) {
+	default:
+		return -EINVAL;
+	case 1:
+		return grpci2_cfg_w8(priv, busno, devfn, where, val);
+	case 2:
+		return grpci2_cfg_w16(priv, busno, devfn, where, val);
+	case 4:
+		return grpci2_cfg_w32(priv, busno, devfn, where, val);
+	}
+}
+
+static struct pci_ops grpci2_ops = {
+	.read =		grpci2_read_config,
+	.write =	grpci2_write_config,
+};
+
+/* GENIRQ IRQ chip implementation for GRPCI2 irqmode=0..2. In configuration
+ * 3 where all PCI Interrupts has a separate IRQ on the system IRQ controller
+ * this is not needed and the standard IRQ controller can be used.
+ */
+
+static void grpci2_mask_irq(struct irq_data *data)
+{
+	unsigned long flags;
+	unsigned int irqidx;
+	struct grpci2_priv *priv = grpci2priv;
+
+	irqidx = (unsigned int)data->chip_data - 1;
+	if (irqidx > 3) /* only mask PCI interrupts here */
+		return;
+
+	spin_lock_irqsave(&grpci2_dev_lock, flags);
+	REGSTORE(priv->regs->ctrl, REGLOAD(priv->regs->ctrl) & ~(1 << irqidx));
+	spin_unlock_irqrestore(&grpci2_dev_lock, flags);
+}
+
+static void grpci2_unmask_irq(struct irq_data *data)
+{
+	unsigned long flags;
+	unsigned int irqidx;
+	struct grpci2_priv *priv = grpci2priv;
+
+	irqidx = (unsigned int)data->chip_data - 1;
+	if (irqidx > 3) /* only unmask PCI interrupts here */
+		return;
+
+	spin_lock_irqsave(&grpci2_dev_lock, flags);
+	REGSTORE(priv->regs->ctrl, REGLOAD(priv->regs->ctrl) | (1 << irqidx));
+	spin_unlock_irqrestore(&grpci2_dev_lock, flags);
+}
+
+static unsigned int grpci2_startup_irq(struct irq_data *data)
+{
+	grpci2_unmask_irq(data);
+	return 0;
+}
+
+static void grpci2_shutdown_irq(struct irq_data *data)
+{
+	grpci2_mask_irq(data);
+}
+
+static struct irq_chip grpci2_irq = {
+	.name		= "grpci2",
+	.irq_startup	= grpci2_startup_irq,
+	.irq_shutdown	= grpci2_shutdown_irq,
+	.irq_mask	= grpci2_mask_irq,
+	.irq_unmask	= grpci2_unmask_irq,
+};
+
+/* Handle one or multiple IRQs from the PCI core */
+static void grpci2_pci_flow_irq(unsigned int irq, struct irq_desc *desc)
+{
+	struct grpci2_priv *priv = grpci2priv;
+	int i, ack = 0;
+	unsigned int ctrl, sts_cap, pci_ints;
+
+	ctrl = REGLOAD(priv->regs->ctrl);
+	sts_cap = REGLOAD(priv->regs->sts_cap);
+
+	/* Error Interrupt? */
+	if (sts_cap & STS_ERR_IRQ) {
+		generic_handle_irq(priv->virq_err);
+		ack = 1;
+	}
+
+	/* PCI Interrupt? */
+	pci_ints = ((~sts_cap) >> STS_INTSTS_BIT) & ctrl & CTRL_HOSTINT;
+	if (pci_ints) {
+		/* Call respective PCI Interrupt handler */
+		for (i = 0; i < 4; i++) {
+			if (pci_ints & (1 << i))
+				generic_handle_irq(priv->irq_map[i]);
+		}
+		ack = 1;
+	}
+
+	/*
+	 * Decode DMA Interrupt only when shared with Err and PCI INTX#, when
+	 * the DMA is a unique IRQ the DMA interrupts doesn't end up here, they
+	 * goes directly to DMA ISR.
+	 */
+	if ((priv->irq_mode == 0) && (sts_cap & (STS_IDMA | STS_IDMAERR))) {
+		generic_handle_irq(priv->virq_dma);
+		ack = 1;
+	}
+
+	/*
+	 * Call "first level" IRQ chip end-of-irq handler. It will ACK LEON IRQ
+	 * Controller, this must be done after IRQ sources have been handled to
+	 * avoid double IRQ generation
+	 */
+	if (ack)
+		desc->irq_data.chip->irq_eoi(&desc->irq_data);
+}
+
+/* Create a virtual IRQ */
+static unsigned int grpci2_build_device_irq(unsigned int irq)
+{
+	unsigned int virq = 0, pil;
+
+	pil = 1 << 8;
+	virq = irq_alloc(irq, pil);
+	if (virq == 0)
+		goto out;
+
+	irq_set_chip_and_handler_name(virq, &grpci2_irq, handle_simple_irq,
+				      "pcilvl");
+	irq_set_chip_data(virq, (void *)irq);
+
+out:
+	return virq;
+}
+
+void grpci2_hw_init(struct grpci2_priv *priv)
+{
+	u32 ahbadr, pciadr, bar_sz, capptr, io_map, data;
+	struct grpci2_regs *regs = priv->regs;
+	int i;
+	struct grpci2_barcfg *barcfg = priv->tgtbars;
+
+	/* Reset any earlier setup */
+	if (priv->do_reset) {
+		printk(KERN_INFO "GRPCI2: Resetting PCI bus\n");
+		REGSTORE(regs->ctrl, CTRL_RESET);
+		ssleep(1); /* Wait for boards to settle */
+	}
+	REGSTORE(regs->ctrl, 0);
+	REGSTORE(regs->sts_cap, ~0); /* Clear Status */
+	REGSTORE(regs->dma_ctrl, 0);
+	REGSTORE(regs->dma_bdbase, 0);
+
+	/* Translate I/O accesses to 0, I/O Space always @ PCI low 64Kbytes */
+	REGSTORE(regs->io_map, REGLOAD(regs->io_map) & 0x0000ffff);
+
+	/* set 1:1 mapping between AHB -> PCI memory space, for all Masters
+	 * Each AHB master has it's own mapping registers. Max 16 AHB masters.
+	 */
+	for (i = 0; i < 16; i++)
+		REGSTORE(regs->ahbmst_map[i], priv->pci_area);
+
+	/* Get the GRPCI2 Host PCI ID */
+	grpci2_cfg_r32(priv, 0, 0, PCI_VENDOR_ID, &priv->pciid);
+
+	/* Get address to first (always defined) capability structure */
+	grpci2_cfg_r8(priv, 0, 0, PCI_CAPABILITY_LIST, &capptr);
+
+	/* Enable/Disable Byte twisting */
+	grpci2_cfg_r32(priv, 0, 0, capptr+CAP9_IOMAP_OFS, &io_map);
+	io_map = (io_map & ~0x1) | (priv->bt_enabled ? 1 : 0);
+	grpci2_cfg_w32(priv, 0, 0, capptr+CAP9_IOMAP_OFS, io_map);
+
+	/* Setup the Host's PCI Target BARs for other peripherals to access,
+	 * and do DMA to the host's memory. The target BARs can be sized and
+	 * enabled individually.
+	 *
+	 * User may set custom target BARs, but default is:
+	 * The first BARs is used to map kernel low (DMA is part of normal
+	 * region on sparc which is SRMMU_MAXMEM big) main memory 1:1 to the
+	 * PCI bus, the other BARs are disabled. We assume that the first BAR
+	 * is always available.
+	 */
+	for (i = 0; i < 6; i++) {
+		if (barcfg[i].pciadr != ~0 && barcfg[i].ahbadr != ~0) {
+			/* Target BARs must have the proper alignment */
+			ahbadr = barcfg[i].ahbadr;
+			pciadr = barcfg[i].pciadr;
+			bar_sz = ((pciadr - 1) & ~pciadr) + 1;
+		} else {
+			if (i == 0) {
+				/* Map main memory */
+				bar_sz = 0xf0000008; /* 256MB prefetchable */
+				ahbadr = 0xf0000000 & (u32)__pa(PAGE_ALIGN(
+					(unsigned long) &_end));
+				pciadr = ahbadr;
+			} else {
+				bar_sz = 0;
+				ahbadr = 0;
+				pciadr = 0;
+			}
+		}
+		grpci2_cfg_w32(priv, 0, 0, capptr+CAP9_BARSIZE_OFS+i*4, bar_sz);
+		grpci2_cfg_w32(priv, 0, 0, PCI_BASE_ADDRESS_0+i*4, pciadr);
+		grpci2_cfg_w32(priv, 0, 0, capptr+CAP9_BAR_OFS+i*4, ahbadr);
+		printk(KERN_INFO "        TGT BAR[%d]: 0x%08x (PCI)-> 0x%08x\n",
+			i, pciadr, ahbadr);
+	}
+
+	/* set as bus master and enable pci memory responses */
+	grpci2_cfg_r32(priv, 0, 0, PCI_COMMAND, &data);
+	data |= (PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+	grpci2_cfg_w32(priv, 0, 0, PCI_COMMAND, data);
+
+	/* Enable Error respone (CPU-TRAP) on illegal memory access. */
+	REGSTORE(regs->ctrl, CTRL_ER | CTRL_PE);
+}
+
+static irqreturn_t grpci2_jump_interrupt(int irq, void *arg)
+{
+	printk(KERN_ERR "GRPCI2: Jump IRQ happened\n");
+	return IRQ_NONE;
+}
+
+/* Handle GRPCI2 Error Interrupt */
+static irqreturn_t grpci2_err_interrupt(int irq, void *arg)
+{
+	struct grpci2_priv *priv = arg;
+	struct grpci2_regs *regs = priv->regs;
+	unsigned int status;
+
+	status = REGLOAD(regs->sts_cap);
+	if ((status & STS_ERR_IRQ) == 0)
+		return IRQ_NONE;
+
+	if (status & STS_IPARERR)
+		printk(KERN_ERR "GRPCI2: Parity Error\n");
+
+	if (status & STS_ITGTABRT)
+		printk(KERN_ERR "GRPCI2: Target Abort\n");
+
+	if (status & STS_IMSTABRT)
+		printk(KERN_ERR "GRPCI2: Master Abort\n");
+
+	if (status & STS_ISYSERR)
+		printk(KERN_ERR "GRPCI2: System Error\n");
+
+	/* Clear handled INT TYPE IRQs */
+	REGSTORE(regs->sts_cap, status & STS_ERR_IRQ);
+
+	return IRQ_HANDLED;
+}
+
+static int __devinit grpci2_of_probe(struct platform_device *ofdev)
+{
+	struct grpci2_regs *regs;
+	struct grpci2_priv *priv;
+	int err, i, len;
+	const int *tmp;
+	unsigned int capability;
+
+	if (grpci2priv) {
+		printk(KERN_ERR "GRPCI2: only one GRPCI2 core supported\n");
+		return -ENODEV;
+	}
+
+	if (ofdev->num_resources < 3) {
+		printk(KERN_ERR "GRPCI2: not enough APB/AHB resources\n");
+		return -EIO;
+	}
+
+	/* Find Device Address */
+	regs = of_ioremap(&ofdev->resource[0], 0,
+			  resource_size(&ofdev->resource[0]),
+			  "grlib-grpci2 regs");
+	if (regs == NULL) {
+		printk(KERN_ERR "GRPCI2: ioremap failed\n");
+		return -EIO;
+	}
+
+	/*
+	 * Check that we're in Host Slot and that we can act as a Host Bridge
+	 * and not only as target.
+	 */
+	capability = REGLOAD(regs->sts_cap);
+	if ((capability & STS_HOST) || !(capability & STS_MST)) {
+		printk(KERN_INFO "GRPCI2: not in host system slot\n");
+		err = -EIO;
+		goto err1;
+	}
+
+	priv = grpci2priv = kzalloc(sizeof(struct grpci2_priv), GFP_KERNEL);
+	if (grpci2priv == NULL) {
+		err = -ENOMEM;
+		goto err1;
+	}
+	memset(grpci2priv, 0, sizeof(*grpci2priv));
+	priv->regs = regs;
+	priv->irq = ofdev->archdata.irqs[0]; /* BASE IRQ */
+	priv->irq_mode = (capability & STS_IRQMODE) >> STS_IRQMODE_BIT;
+
+	printk(KERN_INFO "GRPCI2: host found at %p, irq%d\n", regs, priv->irq);
+
+	/* Byte twisting should be made configurable from kernel command line */
+	priv->bt_enabled = 1;
+
+	/* Let user do custom Target BAR assignment */
+	tmp = of_get_property(ofdev->dev.of_node, "barcfg", &len);
+	if (tmp && (len == 2*4*6))
+		memcpy(priv->tgtbars, tmp, 2*4*6);
+	else
+		memset(priv->tgtbars, -1, 2*4*6);
+
+	/* Limit IRQ unmasking in irq_mode 2 and 3 */
+	tmp = of_get_property(ofdev->dev.of_node, "irq_mask", &len);
+	if (tmp && (len == 4))
+		priv->do_reset = *tmp;
+	else
+		priv->irq_mask = 0xf;
+
+	/* Optional PCI reset. Force PCI reset on startup */
+	tmp = of_get_property(ofdev->dev.of_node, "reset", &len);
+	if (tmp && (len == 4))
+		priv->do_reset = *tmp;
+	else
+		priv->do_reset = 0;
+
+	/* Find PCI Memory, I/O and Configuration Space Windows */
+	priv->pci_area = ofdev->resource[1].start;
+	priv->pci_area_end = ofdev->resource[1].end+1;
+	priv->pci_io = ofdev->resource[2].start;
+	priv->pci_conf = ofdev->resource[2].start + 0x10000;
+	priv->pci_conf_end = priv->pci_conf + 0x10000;
+	priv->pci_io_va = (unsigned long)ioremap(priv->pci_io, 0x10000);
+	if (!priv->pci_io_va) {
+		err = -EIO;
+		goto err2;
+	}
+
+	printk(KERN_INFO
+		"GRPCI2: MEMORY SPACE [0x%08lx - 0x%08lx]\n"
+		"        I/O    SPACE [0x%08lx - 0x%08lx]\n"
+		"        CONFIG SPACE [0x%08lx - 0x%08lx]\n",
+		priv->pci_area, priv->pci_area_end-1,
+		priv->pci_io, priv->pci_conf-1,
+		priv->pci_conf, priv->pci_conf_end-1);
+
+	/*
+	 * I/O Space resources in I/O Window mapped into Virtual Adr Space
+	 * We never use low 4KB because some devices seem have problems using
+	 * address 0.
+	 */
+	memset(&priv->info.io_space, 0, sizeof(struct resource));
+	priv->info.io_space.name = "GRPCI2 PCI I/O Space";
+	priv->info.io_space.start = priv->pci_io_va + 0x1000;
+	priv->info.io_space.end = priv->pci_io_va + 0x10000 - 1;
+	priv->info.io_space.flags = IORESOURCE_IO;
+
+	/*
+	 * GRPCI2 has no prefetchable memory, map everything as
+	 * non-prefetchable memory
+	 */
+	memset(&priv->info.mem_space, 0, sizeof(struct resource));
+	priv->info.mem_space.name = "GRPCI2 PCI MEM Space";
+	priv->info.mem_space.start = priv->pci_area;
+	priv->info.mem_space.end = priv->pci_area_end - 1;
+	priv->info.mem_space.flags = IORESOURCE_MEM;
+
+	if (request_resource(&iomem_resource, &priv->info.mem_space) < 0)
+		goto err3;
+	if (request_resource(&ioport_resource, &priv->info.io_space) < 0)
+		goto err4;
+
+	grpci2_hw_init(priv);
+
+	/*
+	 * Get PCI Interrupt to System IRQ mapping and setup IRQ handling
+	 * Error IRQ always on PCI INTA.
+	 */
+	if (priv->irq_mode < 2) {
+		/* All PCI interrupts are shared using the same system IRQ */
+		leon_update_virq_handling(priv->irq, grpci2_pci_flow_irq,
+					 "pcilvl", 0);
+
+		priv->irq_map[0] = grpci2_build_device_irq(1);
+		priv->irq_map[1] = grpci2_build_device_irq(2);
+		priv->irq_map[2] = grpci2_build_device_irq(3);
+		priv->irq_map[3] = grpci2_build_device_irq(4);
+
+		priv->virq_err = grpci2_build_device_irq(5);
+		if (priv->irq_mode & 1)
+			priv->virq_dma = ofdev->archdata.irqs[1];
+		else
+			priv->virq_dma = grpci2_build_device_irq(6);
+
+		/* Enable IRQs on LEON IRQ controller */
+		err = request_irq(priv->irq, grpci2_jump_interrupt, 0,
+					"GRPCI2_JUMP", priv);
+		if (err)
+			printk(KERN_ERR "GRPCI2: ERR IRQ request failed\n");
+	} else {
+		/* All PCI interrupts have an unique IRQ interrupt */
+		for (i = 0; i < 4; i++) {
+			/* Make LEON IRQ layer handle level IRQ by acking */
+			leon_update_virq_handling(ofdev->archdata.irqs[i],
+						 handle_fasteoi_irq, "pcilvl",
+						 1);
+			priv->irq_map[i] = ofdev->archdata.irqs[i];
+		}
+		priv->virq_err = priv->irq_map[0];
+		if (priv->irq_mode & 1)
+			priv->virq_dma = ofdev->archdata.irqs[4];
+		else
+			priv->virq_dma = priv->irq_map[0];
+
+		/* Unmask all PCI interrupts, request_irq will not do that */
+		REGSTORE(regs->ctrl, REGLOAD(regs->ctrl)|(priv->irq_mask&0xf));
+	}
+
+	/* Setup IRQ handler for non-configuration space access errors */
+	err = request_irq(priv->virq_err, grpci2_err_interrupt, IRQF_SHARED,
+				"GRPCI2_ERR", priv);
+	if (err) {
+		printk(KERN_DEBUG "GRPCI2: ERR VIRQ request failed: %d\n", err);
+		goto err5;
+	}
+
+	/*
+	 * Enable Error Interrupts. PCI interrupts are unmasked once request_irq
+	 * is called by the PCI Device drivers
+	 */
+	REGSTORE(regs->ctrl, REGLOAD(regs->ctrl) | CTRL_EI | CTRL_SI);
+
+	/* Init common layer and scan buses */
+	priv->info.ops = &grpci2_ops;
+	priv->info.map_irq = grpci2_map_irq;
+	leon_pci_init(ofdev, &priv->info);
+
+	return 0;
+
+err5:
+	release_resource(&priv->info.io_space);
+err4:
+	release_resource(&priv->info.mem_space);
+err3:
+	err = -ENOMEM;
+	iounmap((void *)priv->pci_io_va);
+err2:
+	kfree(priv);
+err1:
+	of_iounmap(&ofdev->resource[0], regs,
+		resource_size(&ofdev->resource[0]));
+	return err;
+}
+
+static struct of_device_id grpci2_of_match[] = {
+	{
+	 .name = "GAISLER_GRPCI2",
+	 },
+	{
+	 .name = "01_07c",
+	 },
+	{},
+};
+
+static struct platform_driver grpci2_of_driver = {
+	.driver = {
+		.name = "grpci2",
+		.owner = THIS_MODULE,
+		.of_match_table = grpci2_of_match,
+	},
+	.probe = grpci2_of_probe,
+};
+
+static int __init grpci2_init(void)
+{
+	return platform_driver_register(&grpci2_of_driver);
+}
+
+subsys_initcall(grpci2_init);