@@ -14573,6 +14573,7 @@ M: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
L: netdev@vger.kernel.org
S: Maintained
F: drivers/net/usb/lan78xx.*
+F: include/dt-bindings/net/microchip-78xx.h
USB MASS STORAGE DRIVER
M: Alan Stern <stern@rowland.harvard.edu>
@@ -38,6 +38,7 @@
#include <linux/microchipphy.h>
#include <linux/phy.h>
#include <linux/of_net.h>
+#include <dt-bindings/net/microchip-78xx.h>
#include "lan78xx.h"
#define DRIVER_AUTHOR "WOOJUNG HUH <woojung.huh@microchip.com>"
@@ -74,6 +75,9 @@
#define LAN78XX_EEPROM_MAGIC (0x78A5)
#define LAN78XX_OTP_MAGIC (0x78F3)
+/* This register is specific to the LAN7800 and LAN7850 embedded PHYs */
+#define LAN78XX_PHY_LED_MODE_SELECT 29
+
#define MII_READ 1
#define MII_WRITE 0
@@ -2005,6 +2009,8 @@ static int lan78xx_phy_init(struct lan78xx_net *dev)
{
int ret;
u32 mii_adv;
+ u32 led_modes[4];
+ int len;
struct phy_device *phydev;
phydev = phy_find_first(dev->mdiobus);
@@ -2077,6 +2083,35 @@ static int lan78xx_phy_init(struct lan78xx_net *dev)
mii_adv = (u32)mii_advertise_flowctrl(dev->fc_request_control);
phydev->advertising |= mii_adv_to_ethtool_adv_t(mii_adv);
+ len = of_property_read_variable_u32_array(dev->udev->dev.of_node,
+ "microchip,led-modes",
+ led_modes,
+ 0,
+ ARRAY_SIZE(led_modes));
+ if (len >= 0) {
+ u32 reg = 0;
+ int i;
+
+ for (i = 0; i < len; i++) {
+ if (led_modes[i] > 15) {
+ ret = -EINVAL;
+ goto error;
+ }
+ reg |= led_modes[i] << (i * 4);
+ }
+ for (; i < ARRAY_SIZE(led_modes); i++)
+ reg |= LAN78XX_FORCE_LED_OFF << (i * 4);
+ (void)phy_write(phydev, LAN78XX_PHY_LED_MODE_SELECT, reg);
+
+ /* Ensure the LEDs are enabled */
+ lan78xx_read_reg(dev, HW_CFG, ®);
+ reg |= HW_CFG_LED0_EN_ | HW_CFG_LED1_EN_;
+ lan78xx_write_reg(dev, HW_CFG, reg);
+ } else if (len == -EOVERFLOW) {
+ ret = -EINVAL;
+ goto error;
+ }
+
genphy_config_aneg(phydev);
dev->fc_autoneg = phydev->autoneg;
new file mode 100644
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _DT_BINDINGS_MICROCHIP_LAN78XX_H
+#define _DT_BINDINGS_MICROCHIP_LAN78XX_H
+
+/* LED modes */
+
+#define LAN78XX_LINK_ACTIVITY 0
+#define LAN78XX_LINK_1000_ACTIVITY 1
+#define LAN78XX_LINK_100_ACTIVITY 2
+#define LAN78XX_LINK_10_ACTIVITY 3
+#define LAN78XX_LINK_100_1000_ACTIVITY 4
+#define LAN78XX_LINK_10_1000_ACTIVITY 5
+#define LAN78XX_LINK_10_100_ACTIVITY 6
+#define LAN78XX_DUPLEX_COLLISION 8
+#define LAN78XX_COLLISION 9
+#define LAN78XX_ACTIVITY 10
+#define LAN78XX_AUTONEG_FAULT 12
+#define LAN78XX_FORCE_LED_OFF 14
+#define LAN78XX_FORCE_LED_ON 15
+
+#endif
Add support for DT property "microchip,led-modes", a vector of zero to four cells (u32s) in the range 0-15, each of which sets the mode for one of the LEDs. Some possible values are: 0=link/activity 1=link1000/activity 2=link100/activity 3=link10/activity 4=link100/1000/activity 5=link10/1000/activity 6=link10/100/activity 14=off 15=on These values are given symbolic constants in a dt-bindings header. Also use the presence of the DT property to indicate that the LEDs should be enabled - necessary in the event that no valid OTP or EEPROM is available. Signed-off-by: Phil Elwell <phil@raspberrypi.org> --- MAINTAINERS | 1 + drivers/net/usb/lan78xx.c | 35 ++++++++++++++++++++++++++++++++ include/dt-bindings/net/microchip-78xx.h | 21 +++++++++++++++++++ 3 files changed, 57 insertions(+) create mode 100644 include/dt-bindings/net/microchip-78xx.h