Signed-off-by: Santwona Behera <santwona.behera@sun.com>
---
drivers/net/niu.c | 288 +++++++++++++++++++++++++++++++++++++++++++++++++++-
drivers/net/niu.h | 13 +++
2 files changed, 295 insertions(+), 6 deletions(-)
@@ -406,7 +406,7 @@ static int esr2_set_rx_cfg(struct niu *np, unsigned long channel, u32 val)
}
/* Mode is always 10G fiber. */
-static int serdes_init_niu(struct niu *np)
+static int serdes_init_niu_10g_fiber(struct niu *np)
{
struct niu_link_config *lp = &np->link_config;
u32 tx_cfg, rx_cfg;
@@ -443,6 +443,225 @@ static int serdes_init_niu(struct niu *np)
return 0;
}
+static int serdes_init_niu_1g_serdes(struct niu *np)
+{
+ struct niu_link_config *lp = &np->link_config;
+ u32 tx_cfg, rx_cfg;
+ u16 pll_cfg, pll_sts;
+ unsigned long i;
+ int err;
+ u64 sig, mask, val;
+ int max_retry = 100;
+
+ tx_cfg = (PLL_TX_CFG_ENTX | PLL_TX_CFG_SWING_1375MV |
+ PLL_TX_CFG_RATE_HALF);
+ rx_cfg = (PLL_RX_CFG_ENRX | PLL_RX_CFG_TERM_0P8VDDT |
+ PLL_RX_CFG_ALIGN_ENA | PLL_RX_CFG_LOS_LTHRESH |
+ PLL_RX_CFG_RATE_HALF);
+
+ if (np->port == 0)
+ rx_cfg |= PLL_RX_CFG_EQ_LP_ADAPTIVE;
+
+ if (lp->loopback_mode == LOOPBACK_PHY) {
+ u16 test_cfg = PLL_TEST_CFG_LOOPBACK_CML_DIS;
+
+ mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
+ ESR2_TI_PLL_TEST_CFG_L, test_cfg);
+
+ tx_cfg |= PLL_TX_CFG_ENTEST;
+ rx_cfg |= PLL_RX_CFG_ENTEST;
+ }
+
+ /* Initialize PLL for 1G */
+ pll_cfg = (PLL_CFG_ENPLL | PLL_CFG_MPY_8X);
+
+ err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
+ ESR2_TI_PLL_CFG_L, pll_cfg);
+ if (err) {
+ dev_err(np->device, PFX "NIU Port %d "
+ "serdes_init_niu_1g_serdes: "
+ "mdio write to ESR2_TI_PLL_CFG_L failed", np->port);
+ return err;
+ }
+
+ pll_sts = PLL_CFG_ENPLL;
+
+ err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
+ ESR2_TI_PLL_STS_L, pll_sts);
+ if (err) {
+ dev_err(np->device, PFX "NIU Port %d "
+ "serdes_init_niu_1g_serdes: "
+ "mdio write to ESR2_TI_PLL_STS_L failed", np->port);
+ return err;
+ }
+
+ udelay(200);
+
+ /* Initialize all 4 lanes of the SERDES. */
+ for (i = 0; i < 4; i++) {
+ err = esr2_set_tx_cfg(np, i, tx_cfg);
+ if (err)
+ return err;
+ }
+
+ for (i = 0; i < 4; i++) {
+ err = esr2_set_rx_cfg(np, i, rx_cfg);
+ if (err)
+ return err;
+ }
+
+ switch (np->port) {
+ case 0:
+ val = (ESR_INT_SRDY0_P0 | ESR_INT_DET0_P0);
+ mask = val;
+ break;
+
+ case 1:
+ val = (ESR_INT_SRDY0_P1 | ESR_INT_DET0_P1);
+ mask = val;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ while (max_retry--) {
+ sig = nr64(ESR_INT_SIGNALS);
+ if ((sig & mask) == val)
+ break;
+
+ mdelay(500);
+ }
+
+ if ((sig & mask) != val) {
+ dev_err(np->device, PFX "Port %u signal bits [%08x] are not "
+ "[%08x]\n", np->port, (int) (sig & mask), (int) val);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int serdes_init_niu_10g_serdes(struct niu *np)
+{
+ struct niu_link_config *lp = &np->link_config;
+ u32 tx_cfg, rx_cfg;
+ u32 pll_cfg, pll_sts;
+ unsigned long i;
+ int err;
+ u64 sig, mask, val;
+ int max_retry = 100;
+
+ tx_cfg = (PLL_TX_CFG_ENTX | PLL_TX_CFG_SWING_1375MV);
+ rx_cfg = (PLL_RX_CFG_ENRX | PLL_RX_CFG_TERM_0P8VDDT |
+ PLL_RX_CFG_ALIGN_ENA | PLL_RX_CFG_LOS_LTHRESH |
+ PLL_RX_CFG_EQ_LP_ADAPTIVE);
+
+ if (lp->loopback_mode == LOOPBACK_PHY) {
+ u16 test_cfg = PLL_TEST_CFG_LOOPBACK_CML_DIS;
+
+ mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
+ ESR2_TI_PLL_TEST_CFG_L, test_cfg);
+
+ tx_cfg |= PLL_TX_CFG_ENTEST;
+ rx_cfg |= PLL_RX_CFG_ENTEST;
+ }
+
+ /* Initialize PLL for 10G */
+ pll_cfg = (PLL_CFG_ENPLL | PLL_CFG_MPY_10X);
+
+ err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
+ ESR2_TI_PLL_CFG_L, pll_cfg & 0xffff);
+ if (err) {
+ dev_err(np->device, PFX "NIU Port %d "
+ "serdes_init_niu_10g_serdes: "
+ "mdio write to ESR2_TI_PLL_CFG_L failed", np->port);
+ return err;
+ }
+
+ pll_sts = PLL_CFG_ENPLL;
+
+ err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR,
+ ESR2_TI_PLL_STS_L, pll_sts & 0xffff);
+ if (err) {
+ dev_err(np->device, PFX "NIU Port %d "
+ "serdes_init_niu_10g_serdes: "
+ "mdio write to ESR2_TI_PLL_STS_L failed", np->port);
+ return err;
+ }
+
+ udelay(200);
+
+ /* Initialize all 4 lanes of the SERDES. */
+ for (i = 0; i < 4; i++) {
+ err = esr2_set_tx_cfg(np, i, tx_cfg);
+ if (err)
+ return err;
+ }
+
+ for (i = 0; i < 4; i++) {
+ err = esr2_set_rx_cfg(np, i, rx_cfg);
+ if (err)
+ return err;
+ }
+
+ /* check if serdes is ready */
+
+ switch (np->port) {
+ case 0:
+ mask = ESR_INT_SIGNALS_P0_BITS;
+ val = (ESR_INT_SRDY0_P0 |
+ ESR_INT_DET0_P0 |
+ ESR_INT_XSRDY_P0 |
+ ESR_INT_XDP_P0_CH3 |
+ ESR_INT_XDP_P0_CH2 |
+ ESR_INT_XDP_P0_CH1 |
+ ESR_INT_XDP_P0_CH0);
+ break;
+
+ case 1:
+ mask = ESR_INT_SIGNALS_P1_BITS;
+ val = (ESR_INT_SRDY0_P1 |
+ ESR_INT_DET0_P1 |
+ ESR_INT_XSRDY_P1 |
+ ESR_INT_XDP_P1_CH3 |
+ ESR_INT_XDP_P1_CH2 |
+ ESR_INT_XDP_P1_CH1 |
+ ESR_INT_XDP_P1_CH0);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ while (max_retry--) {
+ sig = nr64(ESR_INT_SIGNALS);
+ if ((sig & mask) == val)
+ break;
+
+ mdelay(500);
+ }
+
+ if ((sig & mask) != val) {
+
+ pr_info(PFX "NIU Port %u signal bits [%08x] are not "
+ "[%08x] for 10G...trying 1G\n",
+ np->port, (int) (sig & mask), (int) val);
+
+ /* 10G failed, try initializing at 1G */
+ err = serdes_init_niu_1g_serdes(np);
+ if (!err) {
+ np->flags &= ~NIU_FLAGS_10G;
+ np->mac_xcvr = MAC_XCVR_PCS;
+ } else {
+ dev_err(np->device, PFX "Port %u 10G/1G SERDES "
+ "Link Failed \n", np->port);
+ return -ENODEV;
+ }
+ }
+ return 0;
+}
+
static int esr_read_rxtx_ctrl(struct niu *np, unsigned long chan, u32 *val)
{
int err;
@@ -1954,13 +2173,23 @@ static const struct niu_phy_ops phy_ops_10g_serdes = {
.link_status = link_status_10g_serdes,
};
+static const struct niu_phy_ops phy_ops_10g_serdes_niu = {
+ .serdes_init = serdes_init_niu_10g_serdes,
+ .link_status = link_status_10g_serdes,
+};
+
+static const struct niu_phy_ops phy_ops_1g_serdes_niu = {
+ .serdes_init = serdes_init_niu_1g_serdes,
+ .link_status = link_status_1g_serdes,
+};
+
static const struct niu_phy_ops phy_ops_1g_rgmii = {
.xcvr_init = xcvr_init_1g_rgmii,
.link_status = link_status_1g_rgmii,
};
static const struct niu_phy_ops phy_ops_10g_fiber_niu = {
- .serdes_init = serdes_init_niu,
+ .serdes_init = serdes_init_niu_10g_fiber,
.xcvr_init = xcvr_init_10g,
.link_status = link_status_10g,
};
@@ -1998,11 +2227,21 @@ struct niu_phy_template {
u32 phy_addr_base;
};
-static const struct niu_phy_template phy_template_niu = {
+static const struct niu_phy_template phy_template_niu_10g_fiber = {
.ops = &phy_ops_10g_fiber_niu,
.phy_addr_base = 16,
};
+static const struct niu_phy_template phy_template_niu_10g_serdes = {
+ .ops = &phy_ops_10g_serdes_niu,
+ .phy_addr_base = 0,
+};
+
+static const struct niu_phy_template phy_template_niu_1g_serdes = {
+ .ops = &phy_ops_1g_serdes_niu,
+ .phy_addr_base = 0,
+};
+
static const struct niu_phy_template phy_template_10g_fiber = {
.ops = &phy_ops_10g_fiber,
.phy_addr_base = 8,
@@ -2182,8 +2421,25 @@ static int niu_determine_phy_disposition(struct niu *np)
u32 phy_addr_off = 0;
if (plat_type == PLAT_TYPE_NIU) {
- tp = &phy_template_niu;
- phy_addr_off += np->port;
+ switch (np->flags &
+ (NIU_FLAGS_10G |
+ NIU_FLAGS_FIBER |
+ NIU_FLAGS_XCVR_SERDES)) {
+ case NIU_FLAGS_10G | NIU_FLAGS_XCVR_SERDES:
+ /* 10G Serdes */
+ tp = &phy_template_niu_10g_serdes;
+ break;
+ case NIU_FLAGS_XCVR_SERDES:
+ /* 1G Serdes */
+ tp = &phy_template_niu_1g_serdes;
+ break;
+ case NIU_FLAGS_10G | NIU_FLAGS_FIBER:
+ /* 10G Fiber */
+ default:
+ tp = &phy_template_niu_10g_fiber;
+ phy_addr_off += np->port;
+ break;
+ }
} else {
switch (np->flags &
(NIU_FLAGS_10G |
@@ -7213,6 +7469,12 @@ static int __devinit niu_phy_type_prop_decode(struct niu *np,
np->flags |= NIU_FLAGS_10G;
np->flags &= ~NIU_FLAGS_FIBER;
np->mac_xcvr = MAC_XCVR_XPCS;
+ } else if (!strcmp(phy_prop, "xgsd") || !strcmp(phy_prop, "gsd")) {
+ /* 10G Serdes or 1G Serdes, default to 10G */
+ np->flags |= NIU_FLAGS_10G;
+ np->flags &= ~NIU_FLAGS_FIBER;
+ np->flags |= NIU_FLAGS_XCVR_SERDES;
+ np->mac_xcvr = MAC_XCVR_XPCS;
} else {
return -EINVAL;
}
@@ -7741,6 +8003,8 @@ static int __devinit walk_phys(struct niu *np, struct niu_parent *parent)
u32 val;
int err;
+ num_10g = num_1g = 0;
+
if (!strcmp(np->vpd.model, NIU_ALONSO_MDL_STR) ||
!strcmp(np->vpd.model, NIU_KIMI_MDL_STR)) {
num_10g = 0;
@@ -7757,6 +8021,16 @@ static int __devinit walk_phys(struct niu *np, struct niu_parent *parent)
parent->num_ports = 2;
val = (phy_encode(PORT_TYPE_10G, 0) |
phy_encode(PORT_TYPE_10G, 1));
+ } else if ((np->flags & NIU_FLAGS_XCVR_SERDES) &&
+ (parent->plat_type == PLAT_TYPE_NIU)) {
+ /* this is the Monza case */
+ if (np->flags & NIU_FLAGS_10G) {
+ val = (phy_encode(PORT_TYPE_10G, 0) |
+ phy_encode(PORT_TYPE_10G, 1));
+ } else {
+ val = (phy_encode(PORT_TYPE_1G, 0) |
+ phy_encode(PORT_TYPE_1G, 1));
+ }
} else {
err = fill_phy_probe_info(np, parent, info);
if (err)
@@ -8656,7 +8930,9 @@ static void __devinit niu_device_announce(struct niu *np)
dev->name,
(np->flags & NIU_FLAGS_XMAC ? "XMAC" : "BMAC"),
(np->flags & NIU_FLAGS_10G ? "10G" : "1G"),
- (np->flags & NIU_FLAGS_FIBER ? "FIBER" : "COPPER"),
+ (np->flags & NIU_FLAGS_FIBER ? "FIBER" :
+ (np->flags & NIU_FLAGS_XCVR_SERDES ? "SERDES" :
+ "COPPER")),
(np->mac_xcvr == MAC_XCVR_MII ? "MII" :
(np->mac_xcvr == MAC_XCVR_PCS ? "PCS" : "XPCS")),
np->vpd.phy_type);
@@ -1048,6 +1048,13 @@
#define PLL_CFG_LD_SHIFT 8
#define PLL_CFG_MPY 0x0000001e
#define PLL_CFG_MPY_SHIFT 1
+#define PLL_CFG_MPY_4X 0x0
+#define PLL_CFG_MPY_5X 0x00000002
+#define PLL_CFG_MPY_6X 0x00000004
+#define PLL_CFG_MPY_8X 0x00000008
+#define PLL_CFG_MPY_10X 0x0000000a
+#define PLL_CFG_MPY_12X 0x0000000c
+#define PLL_CFG_MPY_12P5X 0x0000000e
#define PLL_CFG_ENPLL 0x00000001
#define ESR2_TI_PLL_STS_L (ESR2_BASE + 0x002)
@@ -1093,6 +1100,9 @@
#define PLL_TX_CFG_INVPAIR 0x00000080
#define PLL_TX_CFG_RATE 0x00000060
#define PLL_TX_CFG_RATE_SHIFT 5
+#define PLL_TX_CFG_RATE_FULL 0x0
+#define PLL_TX_CFG_RATE_HALF 0x20
+#define PLL_TX_CFG_RATE_QUAD 0x40
#define PLL_TX_CFG_BUSWIDTH 0x0000001c
#define PLL_TX_CFG_BUSWIDTH_SHIFT 2
#define PLL_TX_CFG_ENTEST 0x00000002
@@ -1132,6 +1142,9 @@
#define PLL_RX_CFG_INVPAIR 0x00000080
#define PLL_RX_CFG_RATE 0x00000060
#define PLL_RX_CFG_RATE_SHIFT 5
+#define PLL_RX_CFG_RATE_FULL 0x0
+#define PLL_RX_CFG_RATE_HALF 0x20
+#define PLL_RX_CFG_RATE_QUAD 0x40
#define PLL_RX_CFG_BUSWIDTH 0x0000001c
#define PLL_RX_CFG_BUSWIDTH_SHIFT 2
#define PLL_RX_CFG_ENTEST 0x00000002
--
1.6.0.4