[v2,06/12] dt-bindings: display: sun4i-drm: Add A83T HDMI pipeline

Message ID 20180110192512.19684-7-jernej.skrabec@siol.net
State New
Headers show
Series
  • drm/sun4i: Add A83T HDMI support
Related show

Commit Message

Jernej Skrabec Jan. 10, 2018, 7:25 p.m.
This commit adds all necessary compatibles and descriptions needed to
implement A83T HDMI pipeline.

Mixer is already properly described, so only compatible is added.

However, A83T TV TCON, which is connected to HDMI, doesn't have channel 0,
contrary to all TCONs currently described. Because of that, TCON
documentation is extended.

A83T features Synopsys DW HDMI controller with a custom PHY which looks
like Synopsys Gen2 PHY with few additions. Since there is no
documentation, needed properties were found out through experimentation
and reading BSP code.

At the end, example is added for newer SoCs, which feature DE2 and DW
HDMI.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
---
 .../bindings/display/sunxi/sun4i-drm.txt           | 197 ++++++++++++++++++++-
 1 file changed, 190 insertions(+), 7 deletions(-)

Patch

diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
index cd626ee1147a..4fb380f3e53d 100644
--- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
+++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
@@ -64,6 +64,52 @@  Required properties:
     first port should be the input endpoint. The second should be the
     output, usually to an HDMI connector.
 
+DWC HDMI TX Encoder
+-------------------
+
+The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+with Allwinner's own PHY IP. It supports audio and video outputs and CEC.
+
+These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
+Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
+following device-specific properties.
+
+Required properties:
+
+  - compatible: value must be one of:
+    * "allwinner,sun8i-a83t-dw-hdmi"
+  - reg: base address and size of memory-mapped region
+  - reg-io-width: See dw_hdmi.txt. Shall be 1.
+  - interrupts: HDMI interrupt number
+  - clocks: phandles to the clocks feeding the HDMI encoder
+    * iahb: the HDMI bus clock
+    * isfr: the HDMI register clock
+  - clock-names: the clock names mentioned above
+  - resets: phandle to the reset controller
+  - reset-names: must be "ctrl"
+  - phys: phandle to the DWC HDMI PHY
+  - phy-names: must be "phy"
+
+  - ports: A ports node with endpoint definitions as defined in
+    Documentation/devicetree/bindings/media/video-interfaces.txt. The
+    first port should be the input endpoint. The second should be the
+    output, usually to an HDMI connector.
+
+DWC HDMI PHY
+------------
+
+Required properties:
+  - compatible: value must be one of:
+    * allwinner,sun8i-a83t-hdmi-phy
+  - reg: base address and size of memory-mapped region
+  - clocks: phandles to the clocks feeding the HDMI PHY
+    * bus: the HDMI PHY interface clock
+    * mod: the HDMI PHY module clock
+    * tmds: TMDS clock
+  - clock-names: the clock names mentioned above
+  - resets: phandle to the reset controller driving the PHY
+  - reset-names: must be "phy"
+
 TV Encoder
 ----------
 
@@ -94,24 +140,23 @@  Required properties:
    * allwinner,sun7i-a20-tcon
    * allwinner,sun8i-a33-tcon
    * allwinner,sun8i-a83t-tcon-lcd
+   * allwinner,sun8i-a83t-tcon-tv
    * allwinner,sun8i-v3s-tcon
  - reg: base address and size of memory-mapped region
  - interrupts: interrupt associated to this IP
- - clocks: phandles to the clocks feeding the TCON. Three are needed:
+ - clocks: phandles to the clocks feeding the TCON. One is needed:
    - 'ahb': the interface clocks
-   - 'tcon-ch0': The clock driving the TCON channel 0
  - resets: phandles to the reset controllers driving the encoder
    - "lcd": the reset line for the TCON channel 0
 
  - clock-names: the clock names mentioned above
  - reset-names: the reset names mentioned above
- - clock-output-names: Name of the pixel clock created
 
 - ports: A ports node with endpoint definitions as defined in
   Documentation/devicetree/bindings/media/video-interfaces.txt. The
   first port should be the input endpoint, the second one the output
 
-  The output may have multiple endpoints. The TCON has two channels,
+  The output may have multiple endpoints. TCON can have two channels,
   usually with the first channel being used for the panels interfaces
   (RGB, LVDS, etc.), and the second being used for the outputs that
   require another controller (TV Encoder, HDMI, etc.). The endpoints
@@ -119,11 +164,16 @@  Required properties:
   channel the endpoint is associated to. If that property is not
   present, the endpoint number will be used as the channel number.
 
+When TCON supports channel 0 (all TCONs except TV TCON on A83T), two
+more clocks are needed:
+   - 'tcon-ch0': The clock driving the TCON channel 0
+   - clock-output-names: Name of the pixel clock created
+
 On SoCs other than the A33 and V3s, there is one more clock required:
    - 'tcon-ch1': The clock driving the TCON channel 1
 
-On SoCs that support LVDS (all SoCs but the A13, H3, H5 and V3s), you
-need one more reset line:
+When TCON support LVDS (all TCONs except TV TCON on A83T and those found
+in A13, H3, H5 and V3s SoCs), you need one more reset line:
    - 'lvds': The reset line driving the LVDS logic
 
 And on the A23, A31, A31s and A33, you need one more clock line:
@@ -226,6 +276,7 @@  supported.
 Required properties:
   - compatible: value must be one of:
     * allwinner,sun8i-a83t-de2-mixer-0
+    * allwinner,sun8i-a83t-de2-mixer-1
     * allwinner,sun8i-v3s-de2-mixer
   - reg: base address and size of the memory-mapped region.
   - clocks: phandles to the clocks feeding the mixer
@@ -261,7 +312,7 @@  Required properties:
   - allwinner,pipelines: list of phandle to the display engine
     frontends (DE 1.0) or mixers (DE 2.0) available.
 
-Example:
+Example 1:
 
 panel: panel {
 	compatible = "olimex,lcd-olinuxino-43-ts";
@@ -460,3 +511,135 @@  display-engine {
 	compatible = "allwinner,sun5i-a13-display-engine";
 	allwinner,pipelines = <&fe0>;
 };
+
+Example 2:
+
+connector {
+	compatible = "hdmi-connector";
+	type = "a";
+
+	port {
+		hdmi_con_in: endpoint {
+			remote-endpoint = <&hdmi_out_con>;
+		};
+	};
+};
+
+de: display-engine {
+	compatible = "allwinner,sun8i-a83t-display-engine";
+	allwinner,pipelines = <&mixer1>;
+};
+
+mixer1: mixer@1200000 {
+	compatible = "allwinner,sun8i-a83t-de2-mixer-1";
+	reg = <0x01200000 0x100000>;
+	clocks = <&display_clocks CLK_BUS_MIXER1>,
+		 <&display_clocks CLK_MIXER1>;
+	clock-names = "bus",
+		      "mod";
+	resets = <&display_clocks RST_WB>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mixer1_out: port@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			mixer1_out_tcon1: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&tcon1_in_mixer1>;
+			};
+		};
+	};
+};
+
+tcon1: lcd-controller@1c0d000 {
+	compatible = "allwinner,sun8i-a83t-tcon-tv";
+	reg = <0x01c0d000 0x1000>;
+	interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&ccu CLK_BUS_TCON1>, <&ccu CLK_TCON1>;
+	clock-names = "ahb", "tcon-ch1";
+	resets = <&ccu RST_BUS_TCON1>;
+	reset-names = "lcd";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		tcon1_in: port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			tcon1_in_mixer1: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&mixer1_out_tcon1>;
+			};
+		};
+
+		tcon1_out: port@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			tcon1_out_hdmi: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&hdmi_in_tcon1>;
+			};
+		};
+	};
+};
+
+hdmi: hdmi@1ee0000 {
+	compatible = "allwinner,sun8i-a83t-dw-hdmi";
+	reg = <0x01ee0000 0x10000>;
+	reg-io-width = <1>;
+	interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_SLOW>;
+	clock-names = "iahb", "isfr";
+	resets = <&ccu RST_BUS_HDMI1>;
+	reset-names = "ctrl";
+	phys = <&hdmi_phy>;
+	phy-names = "hdmi-phy";
+	status = "disabled";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hdmi_in: port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			hdmi_in_tcon1: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&tcon1_out_hdmi>;
+			};
+		};
+
+		hdmi_out: port@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			hdmi_out_con: endpoint {
+				remote-endpoint = <&hdmi_con_in>;
+			};
+		};
+	};
+};
+
+hdmi_phy: hdmi-phy@1ef0000 {
+	compatible = "allwinner,sun8i-a83t-hdmi-phy";
+	reg = <0x01ef0000 0x10000>;
+	clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_SLOW>,
+		 <&ccu CLK_HDMI>;
+	clock-names = "bus", "mod", "tmds";
+	resets = <&ccu RST_BUS_HDMI0>;
+	reset-names = "phy";
+	#phy-cells = <0>;
+};