[v3,5/7] mtd: nand: use Marvell reworked NAND controller driver with all platforms

Message ID 20180109103637.23798-6-miquel.raynal@free-electrons.com
State New
Headers show
Series
  • Marvell NAND controller rework with ->exec_op()
Related show

Commit Message

Miquel Raynal Jan. 9, 2018, 10:36 a.m.
Actually remove pxa3xx_nand.c to let marvell_nand.c be compiled instead.
Also change the defconfig files using it as well as some board files
depending on CONFIG_MTD_NAND_PXA3xx.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
 arch/arm/configs/cm_x300_defconfig  |    2 +-
 arch/arm/configs/pxa3xx_defconfig   |    3 +-
 arch/arm/configs/pxa_defconfig      |    2 +-
 arch/arm/configs/raumfeld_defconfig |    2 +-
 arch/arm/mach-mmp/ttc_dkb.c         |    4 +-
 arch/arm/mach-pxa/cm-x300.c         |    2 +-
 arch/arm/mach-pxa/colibri-pxa3xx.c  |    2 +-
 arch/arm/mach-pxa/colibri.h         |    2 +-
 arch/arm/mach-pxa/littleton.c       |    4 +-
 arch/arm/mach-pxa/mxm8x10.c         |    4 +-
 arch/arm/mach-pxa/zylonite.c        |    4 +-
 drivers/mtd/nand/Kconfig            |   11 -
 drivers/mtd/nand/Makefile           |    1 -
 drivers/mtd/nand/pxa3xx_nand.c      | 2104 -----------------------------------
 14 files changed, 15 insertions(+), 2132 deletions(-)
 delete mode 100644 drivers/mtd/nand/pxa3xx_nand.c

Comments

Boris Brezillon Feb. 12, 2018, 10:20 a.m. | #1
On Tue,  9 Jan 2018 11:36:35 +0100
Miquel Raynal <miquel.raynal@free-electrons.com> wrote:

> Actually remove pxa3xx_nand.c to let marvell_nand.c be compiled instead.
> Also change the defconfig files using it as well as some board files
> depending on CONFIG_MTD_NAND_PXA3xx.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
> ---
>  arch/arm/configs/cm_x300_defconfig  |    2 +-
>  arch/arm/configs/pxa3xx_defconfig   |    3 +-
>  arch/arm/configs/pxa_defconfig      |    2 +-
>  arch/arm/configs/raumfeld_defconfig |    2 +-
>  arch/arm/mach-mmp/ttc_dkb.c         |    4 +-
>  arch/arm/mach-pxa/cm-x300.c         |    2 +-
>  arch/arm/mach-pxa/colibri-pxa3xx.c  |    2 +-
>  arch/arm/mach-pxa/colibri.h         |    2 +-
>  arch/arm/mach-pxa/littleton.c       |    4 +-
>  arch/arm/mach-pxa/mxm8x10.c         |    4 +-
>  arch/arm/mach-pxa/zylonite.c        |    4 +-
>  drivers/mtd/nand/Kconfig            |   11 -
>  drivers/mtd/nand/Makefile           |    1 -
>  drivers/mtd/nand/pxa3xx_nand.c      | 2104 -----------------------------------

Can you please split this patch in 2, one that patches defconfig and
board files to use the new driver and one that actually removes the old
driver.

Thanks,

Boris

Patch

diff --git a/arch/arm/configs/cm_x300_defconfig b/arch/arm/configs/cm_x300_defconfig
index c0418e03d180..5e349c625b71 100644
--- a/arch/arm/configs/cm_x300_defconfig
+++ b/arch/arm/configs/cm_x300_defconfig
@@ -49,7 +49,7 @@  CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_MTD=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_PXA3xx=y
+CONFIG_MTD_NAND_MARVELL=y
 CONFIG_MTD_UBI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
diff --git a/arch/arm/configs/pxa3xx_defconfig b/arch/arm/configs/pxa3xx_defconfig
index bfea6874b0a1..3e0de035ab77 100644
--- a/arch/arm/configs/pxa3xx_defconfig
+++ b/arch/arm/configs/pxa3xx_defconfig
@@ -32,8 +32,7 @@  CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_MTD=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_PXA3xx=y
-CONFIG_MTD_NAND_PXA3xx_BUILTIN=y
+CONFIG_MTD_NAND_MARVELL=y
 CONFIG_MTD_ONENAND=y
 CONFIG_MTD_ONENAND_VERIFY_WRITE=y
 CONFIG_MTD_ONENAND_GENERIC=y
diff --git a/arch/arm/configs/pxa_defconfig b/arch/arm/configs/pxa_defconfig
index 830e817a028a..934af8601f7d 100644
--- a/arch/arm/configs/pxa_defconfig
+++ b/arch/arm/configs/pxa_defconfig
@@ -198,7 +198,7 @@  CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0x4000000
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH=y
 CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE=y
 CONFIG_MTD_NAND_SHARPSL=m
-CONFIG_MTD_NAND_PXA3xx=m
+CONFIG_MTD_NAND_MARVELL=m
 CONFIG_MTD_NAND_CM_X270=m
 CONFIG_MTD_NAND_TMIO=m
 CONFIG_MTD_NAND_BRCMNAND=m
diff --git a/arch/arm/configs/raumfeld_defconfig b/arch/arm/configs/raumfeld_defconfig
index 77a56c23c6ef..2dd56e9a484e 100644
--- a/arch/arm/configs/raumfeld_defconfig
+++ b/arch/arm/configs/raumfeld_defconfig
@@ -33,7 +33,7 @@  CONFIG_NFTL=y
 CONFIG_NFTL_RW=y
 CONFIG_MTD_BLOCK2MTD=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_PXA3xx=y
+CONFIG_MTD_NAND_MARVELL=y
 CONFIG_MTD_UBI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_ISL29003=y
diff --git a/arch/arm/mach-mmp/ttc_dkb.c b/arch/arm/mach-mmp/ttc_dkb.c
index d90c74fa614d..e0b6073c61a7 100644
--- a/arch/arm/mach-mmp/ttc_dkb.c
+++ b/arch/arm/mach-mmp/ttc_dkb.c
@@ -178,7 +178,7 @@  static struct mv_usb_platform_data ttc_usb_pdata = {
 #endif
 #endif
 
-#if IS_ENABLED(CONFIG_MTD_NAND_PXA3xx)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
 static struct pxa3xx_nand_platform_data dkb_nand_info = {
 	.enable_arbiter = 1,
 	.num_cs = 1,
@@ -275,7 +275,7 @@  static void __init ttc_dkb_init(void)
 
 	/* on-chip devices */
 	pxa910_add_uart(1);
-#if IS_ENABLED(CONFIG_MTD_NAND_PXA3xx)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
 	pxa910_add_nand(&dkb_nand_info);
 #endif
 
diff --git a/arch/arm/mach-pxa/cm-x300.c b/arch/arm/mach-pxa/cm-x300.c
index 868448d2cd82..fe1c76bca212 100644
--- a/arch/arm/mach-pxa/cm-x300.c
+++ b/arch/arm/mach-pxa/cm-x300.c
@@ -391,7 +391,7 @@  static void __init cm_x300_init_ac97(void)
 static inline void cm_x300_init_ac97(void) {}
 #endif
 
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
 static struct mtd_partition cm_x300_nand_partitions[] = {
 	[0] = {
 		.name        = "OBM",
diff --git a/arch/arm/mach-pxa/colibri-pxa3xx.c b/arch/arm/mach-pxa/colibri-pxa3xx.c
index b04431bb4ba7..3018eafd723e 100644
--- a/arch/arm/mach-pxa/colibri-pxa3xx.c
+++ b/arch/arm/mach-pxa/colibri-pxa3xx.c
@@ -110,7 +110,7 @@  void __init colibri_pxa3xx_init_lcd(int bl_pin)
 }
 #endif
 
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
 static struct mtd_partition colibri_nand_partitions[] = {
 	{
 		.name        = "bootloader",
diff --git a/arch/arm/mach-pxa/colibri.h b/arch/arm/mach-pxa/colibri.h
index 673a131da875..85525d49e321 100644
--- a/arch/arm/mach-pxa/colibri.h
+++ b/arch/arm/mach-pxa/colibri.h
@@ -46,7 +46,7 @@  static inline void colibri_pxa3xx_init_lcd(int bl_pin) {}
 extern void colibri_pxa3xx_init_eth(struct ax_plat_data *plat_data);
 #endif
 
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
 extern void colibri_pxa3xx_init_nand(void);
 #else
 static inline void colibri_pxa3xx_init_nand(void) {}
diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c
index fae38fdc8d8e..380b07a15ef9 100644
--- a/arch/arm/mach-pxa/littleton.c
+++ b/arch/arm/mach-pxa/littleton.c
@@ -290,7 +290,7 @@  static void __init littleton_init_mmc(void)
 static inline void littleton_init_mmc(void) {}
 #endif
 
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
 static struct mtd_partition littleton_nand_partitions[] = {
 	[0] = {
 		.name        = "Bootloader",
@@ -340,7 +340,7 @@  static void __init littleton_init_nand(void)
 }
 #else
 static inline void littleton_init_nand(void) {}
-#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */
+#endif /* IS_ENABLED(CONFIG_MTD_NAND_MARVELL) */
 
 #if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE)
 static struct led_info littleton_da9034_leds[] = {
diff --git a/arch/arm/mach-pxa/mxm8x10.c b/arch/arm/mach-pxa/mxm8x10.c
index 9a22ae0ad8c9..743d983fc222 100644
--- a/arch/arm/mach-pxa/mxm8x10.c
+++ b/arch/arm/mach-pxa/mxm8x10.c
@@ -359,7 +359,7 @@  void __init mxm_8x10_ac97_init(void)
 }
 
 /* NAND flash Support */
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
 #define NAND_BLOCK_SIZE SZ_128K
 #define NB(x)           (NAND_BLOCK_SIZE * (x))
 static struct mtd_partition mxm_8x10_nand_partitions[] = {
@@ -402,7 +402,7 @@  static void __init mxm_8x10_nand_init(void)
 }
 #else
 static inline void mxm_8x10_nand_init(void) {}
-#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */
+#endif /* IS_ENABLED(CONFIG_MTD_NAND_MARVELL) */
 
 /* Ethernet support: Davicom DM9000 */
 static struct resource dm9k_resources[] = {
diff --git a/arch/arm/mach-pxa/zylonite.c b/arch/arm/mach-pxa/zylonite.c
index 4268552d600d..3a99fc054e96 100644
--- a/arch/arm/mach-pxa/zylonite.c
+++ b/arch/arm/mach-pxa/zylonite.c
@@ -338,7 +338,7 @@  static void __init zylonite_init_keypad(void)
 static inline void zylonite_init_keypad(void) {}
 #endif
 
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
 static struct mtd_partition zylonite_nand_partitions[] = {
 	[0] = {
 		.name        = "Bootloader",
@@ -388,7 +388,7 @@  static void __init zylonite_init_nand(void)
 }
 #else
 static inline void zylonite_init_nand(void) {}
-#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */
+#endif /* IS_ENABLED(CONFIG_MTD_NAND_MARVELL) */
 
 #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
 static struct pxaohci_platform_data zylonite_ohci_info = {
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index e6b8c59f2c0d..2c6ecb7ae753 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -313,17 +313,6 @@  config MTD_NAND_ATMEL
 	  Enables support for NAND Flash / Smart Media Card interface
 	  on Atmel AT91 processors.
 
-config MTD_NAND_PXA3xx
-	tristate "NAND support on PXA3xx and Armada 370/XP"
-	depends on !MTD_NAND_MARVELL
-	depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU
-	help
-
-	  This enables the driver for the NAND flash device found on
-	  PXA3xx processors (NFCv1) and also on 32-bit Armada
-	  platforms (XP, 370, 375, 38x, 39x) and 64-bit Armada
-	  platforms (7K, 8K) (NFCv2).
-
 config MTD_NAND_MARVELL
 	tristate "NAND controller support on Marvell boards"
 	depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 921634ba400c..c882d5ef192a 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -31,7 +31,6 @@  omap2_nand-objs := omap2.o
 obj-$(CONFIG_MTD_NAND_OMAP2) 		+= omap2_nand.o
 obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD)	+= omap_elm.o
 obj-$(CONFIG_MTD_NAND_CM_X270)		+= cmx270_nand.o
-obj-$(CONFIG_MTD_NAND_PXA3xx)		+= pxa3xx_nand.o
 obj-$(CONFIG_MTD_NAND_MARVELL)		+= marvell_nand.o
 obj-$(CONFIG_MTD_NAND_TMIO)		+= tmio_nand.o
 obj-$(CONFIG_MTD_NAND_PLATFORM)		+= plat_nand.o
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
deleted file mode 100644
index 021374fe59dc..000000000000
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ /dev/null
@@ -1,2104 +0,0 @@ 
-/*
- * drivers/mtd/nand/pxa3xx_nand.c
- *
- * Copyright © 2005 Intel Corporation
- * Copyright © 2006 Marvell International Ltd.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * See Documentation/mtd/nand/pxa3xx-nand.txt for more details.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/dmaengine.h>
-#include <linux/dma-mapping.h>
-#include <linux/dma/pxa-dma.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/rawnand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/io.h>
-#include <linux/iopoll.h>
-#include <linux/irq.h>
-#include <linux/slab.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/platform_data/mtd-nand-pxa3xx.h>
-#include <linux/mfd/syscon.h>
-#include <linux/regmap.h>
-
-#define	CHIP_DELAY_TIMEOUT	msecs_to_jiffies(200)
-#define NAND_STOP_DELAY		msecs_to_jiffies(40)
-#define PAGE_CHUNK_SIZE		(2048)
-
-/*
- * Define a buffer size for the initial command that detects the flash device:
- * STATUS, READID and PARAM.
- * ONFI param page is 256 bytes, and there are three redundant copies
- * to be read. JEDEC param page is 512 bytes, and there are also three
- * redundant copies to be read.
- * Hence this buffer should be at least 512 x 3. Let's pick 2048.
- */
-#define INIT_BUFFER_SIZE	2048
-
-/* System control register and bit to enable NAND on some SoCs */
-#define GENCONF_SOC_DEVICE_MUX	0x208
-#define GENCONF_SOC_DEVICE_MUX_NFC_EN BIT(0)
-
-/* registers and bit definitions */
-#define NDCR		(0x00) /* Control register */
-#define NDTR0CS0	(0x04) /* Timing Parameter 0 for CS0 */
-#define NDTR1CS0	(0x0C) /* Timing Parameter 1 for CS0 */
-#define NDSR		(0x14) /* Status Register */
-#define NDPCR		(0x18) /* Page Count Register */
-#define NDBDR0		(0x1C) /* Bad Block Register 0 */
-#define NDBDR1		(0x20) /* Bad Block Register 1 */
-#define NDECCCTRL	(0x28) /* ECC control */
-#define NDDB		(0x40) /* Data Buffer */
-#define NDCB0		(0x48) /* Command Buffer0 */
-#define NDCB1		(0x4C) /* Command Buffer1 */
-#define NDCB2		(0x50) /* Command Buffer2 */
-
-#define NDCR_SPARE_EN		(0x1 << 31)
-#define NDCR_ECC_EN		(0x1 << 30)
-#define NDCR_DMA_EN		(0x1 << 29)
-#define NDCR_ND_RUN		(0x1 << 28)
-#define NDCR_DWIDTH_C		(0x1 << 27)
-#define NDCR_DWIDTH_M		(0x1 << 26)
-#define NDCR_PAGE_SZ		(0x1 << 24)
-#define NDCR_NCSX		(0x1 << 23)
-#define NDCR_ND_MODE		(0x3 << 21)
-#define NDCR_NAND_MODE   	(0x0)
-#define NDCR_CLR_PG_CNT		(0x1 << 20)
-#define NFCV1_NDCR_ARB_CNTL	(0x1 << 19)
-#define NFCV2_NDCR_STOP_ON_UNCOR	(0x1 << 19)
-#define NDCR_RD_ID_CNT_MASK	(0x7 << 16)
-#define NDCR_RD_ID_CNT(x)	(((x) << 16) & NDCR_RD_ID_CNT_MASK)
-
-#define NDCR_RA_START		(0x1 << 15)
-#define NDCR_PG_PER_BLK		(0x1 << 14)
-#define NDCR_ND_ARB_EN		(0x1 << 12)
-#define NDCR_INT_MASK           (0xFFF)
-
-#define NDSR_MASK		(0xfff)
-#define NDSR_ERR_CNT_OFF	(16)
-#define NDSR_ERR_CNT_MASK       (0x1f)
-#define NDSR_ERR_CNT(sr)	((sr >> NDSR_ERR_CNT_OFF) & NDSR_ERR_CNT_MASK)
-#define NDSR_RDY                (0x1 << 12)
-#define NDSR_FLASH_RDY          (0x1 << 11)
-#define NDSR_CS0_PAGED		(0x1 << 10)
-#define NDSR_CS1_PAGED		(0x1 << 9)
-#define NDSR_CS0_CMDD		(0x1 << 8)
-#define NDSR_CS1_CMDD		(0x1 << 7)
-#define NDSR_CS0_BBD		(0x1 << 6)
-#define NDSR_CS1_BBD		(0x1 << 5)
-#define NDSR_UNCORERR		(0x1 << 4)
-#define NDSR_CORERR		(0x1 << 3)
-#define NDSR_WRDREQ		(0x1 << 2)
-#define NDSR_RDDREQ		(0x1 << 1)
-#define NDSR_WRCMDREQ		(0x1)
-
-#define NDCB0_LEN_OVRD		(0x1 << 28)
-#define NDCB0_ST_ROW_EN         (0x1 << 26)
-#define NDCB0_AUTO_RS		(0x1 << 25)
-#define NDCB0_CSEL		(0x1 << 24)
-#define NDCB0_EXT_CMD_TYPE_MASK	(0x7 << 29)
-#define NDCB0_EXT_CMD_TYPE(x)	(((x) << 29) & NDCB0_EXT_CMD_TYPE_MASK)
-#define NDCB0_CMD_TYPE_MASK	(0x7 << 21)
-#define NDCB0_CMD_TYPE(x)	(((x) << 21) & NDCB0_CMD_TYPE_MASK)
-#define NDCB0_NC		(0x1 << 20)
-#define NDCB0_DBC		(0x1 << 19)
-#define NDCB0_ADDR_CYC_MASK	(0x7 << 16)
-#define NDCB0_ADDR_CYC(x)	(((x) << 16) & NDCB0_ADDR_CYC_MASK)
-#define NDCB0_CMD2_MASK		(0xff << 8)
-#define NDCB0_CMD1_MASK		(0xff)
-#define NDCB0_ADDR_CYC_SHIFT	(16)
-
-#define EXT_CMD_TYPE_DISPATCH	6 /* Command dispatch */
-#define EXT_CMD_TYPE_NAKED_RW	5 /* Naked read or Naked write */
-#define EXT_CMD_TYPE_READ	4 /* Read */
-#define EXT_CMD_TYPE_DISP_WR	4 /* Command dispatch with write */
-#define EXT_CMD_TYPE_FINAL	3 /* Final command */
-#define EXT_CMD_TYPE_LAST_RW	1 /* Last naked read/write */
-#define EXT_CMD_TYPE_MONO	0 /* Monolithic read/write */
-
-/*
- * This should be large enough to read 'ONFI' and 'JEDEC'.
- * Let's use 7 bytes, which is the maximum ID count supported
- * by the controller (see NDCR_RD_ID_CNT_MASK).
- */
-#define READ_ID_BYTES		7
-
-/* macros for registers read/write */
-#define nand_writel(info, off, val)					\
-	do {								\
-		dev_vdbg(&info->pdev->dev,				\
-			 "%s():%d nand_writel(0x%x, 0x%04x)\n",		\
-			 __func__, __LINE__, (val), (off));		\
-		writel_relaxed((val), (info)->mmio_base + (off));	\
-	} while (0)
-
-#define nand_readl(info, off)						\
-	({								\
-		unsigned int _v;					\
-		_v = readl_relaxed((info)->mmio_base + (off));		\
-		dev_vdbg(&info->pdev->dev,				\
-			 "%s():%d nand_readl(0x%04x) = 0x%x\n",		\
-			 __func__, __LINE__, (off), _v);		\
-		_v;							\
-	})
-
-/* error code and state */
-enum {
-	ERR_NONE	= 0,
-	ERR_DMABUSERR	= -1,
-	ERR_SENDCMD	= -2,
-	ERR_UNCORERR	= -3,
-	ERR_BBERR	= -4,
-	ERR_CORERR	= -5,
-};
-
-enum {
-	STATE_IDLE = 0,
-	STATE_PREPARED,
-	STATE_CMD_HANDLE,
-	STATE_DMA_READING,
-	STATE_DMA_WRITING,
-	STATE_DMA_DONE,
-	STATE_PIO_READING,
-	STATE_PIO_WRITING,
-	STATE_CMD_DONE,
-	STATE_READY,
-};
-
-enum pxa3xx_nand_variant {
-	PXA3XX_NAND_VARIANT_PXA,
-	PXA3XX_NAND_VARIANT_ARMADA370,
-	PXA3XX_NAND_VARIANT_ARMADA_8K,
-};
-
-struct pxa3xx_nand_host {
-	struct nand_chip	chip;
-	void			*info_data;
-
-	/* page size of attached chip */
-	int			use_ecc;
-	int			cs;
-
-	/* calculated from pxa3xx_nand_flash data */
-	unsigned int		col_addr_cycles;
-	unsigned int		row_addr_cycles;
-};
-
-struct pxa3xx_nand_info {
-	struct nand_hw_control	controller;
-	struct platform_device	 *pdev;
-
-	struct clk		*clk;
-	void __iomem		*mmio_base;
-	unsigned long		mmio_phys;
-	struct completion	cmd_complete, dev_ready;
-
-	unsigned int 		buf_start;
-	unsigned int		buf_count;
-	unsigned int		buf_size;
-	unsigned int		data_buff_pos;
-	unsigned int		oob_buff_pos;
-
-	/* DMA information */
-	struct scatterlist	sg;
-	enum dma_data_direction	dma_dir;
-	struct dma_chan		*dma_chan;
-	dma_cookie_t		dma_cookie;
-	int			drcmr_dat;
-
-	unsigned char		*data_buff;
-	unsigned char		*oob_buff;
-	dma_addr_t 		data_buff_phys;
-	int 			data_dma_ch;
-
-	struct pxa3xx_nand_host *host[NUM_CHIP_SELECT];
-	unsigned int		state;
-
-	/*
-	 * This driver supports NFCv1 (as found in PXA SoC)
-	 * and NFCv2 (as found in Armada 370/XP SoC).
-	 */
-	enum pxa3xx_nand_variant variant;
-
-	int			cs;
-	int			use_ecc;	/* use HW ECC ? */
-	int			ecc_bch;	/* using BCH ECC? */
-	int			use_dma;	/* use DMA ? */
-	int			use_spare;	/* use spare ? */
-	int			need_wait;
-
-	/* Amount of real data per full chunk */
-	unsigned int		chunk_size;
-
-	/* Amount of spare data per full chunk */
-	unsigned int		spare_size;
-
-	/* Number of full chunks (i.e chunk_size + spare_size) */
-	unsigned int            nfullchunks;
-
-	/*
-	 * Total number of chunks. If equal to nfullchunks, then there
-	 * are only full chunks. Otherwise, there is one last chunk of
-	 * size (last_chunk_size + last_spare_size)
-	 */
-	unsigned int            ntotalchunks;
-
-	/* Amount of real data in the last chunk */
-	unsigned int		last_chunk_size;
-
-	/* Amount of spare data in the last chunk */
-	unsigned int		last_spare_size;
-
-	unsigned int		ecc_size;
-	unsigned int		ecc_err_cnt;
-	unsigned int		max_bitflips;
-	int 			retcode;
-
-	/*
-	 * Variables only valid during command
-	 * execution. step_chunk_size and step_spare_size is the
-	 * amount of real data and spare data in the current
-	 * chunk. cur_chunk is the current chunk being
-	 * read/programmed.
-	 */
-	unsigned int		step_chunk_size;
-	unsigned int		step_spare_size;
-	unsigned int            cur_chunk;
-
-	/* cached register value */
-	uint32_t		reg_ndcr;
-	uint32_t		ndtr0cs0;
-	uint32_t		ndtr1cs0;
-
-	/* generated NDCBx register values */
-	uint32_t		ndcb0;
-	uint32_t		ndcb1;
-	uint32_t		ndcb2;
-	uint32_t		ndcb3;
-};
-
-static bool use_dma = 1;
-module_param(use_dma, bool, 0444);
-MODULE_PARM_DESC(use_dma, "enable DMA for data transferring to/from NAND HW");
-
-struct pxa3xx_nand_timing {
-	unsigned int	tCH;  /* Enable signal hold time */
-	unsigned int	tCS;  /* Enable signal setup time */
-	unsigned int	tWH;  /* ND_nWE high duration */
-	unsigned int	tWP;  /* ND_nWE pulse time */
-	unsigned int	tRH;  /* ND_nRE high duration */
-	unsigned int	tRP;  /* ND_nRE pulse width */
-	unsigned int	tR;   /* ND_nWE high to ND_nRE low for read */
-	unsigned int	tWHR; /* ND_nWE high to ND_nRE low for status read */
-	unsigned int	tAR;  /* ND_ALE low to ND_nRE low delay */
-};
-
-struct pxa3xx_nand_flash {
-	uint32_t	chip_id;
-	unsigned int	flash_width;	/* Width of Flash memory (DWIDTH_M) */
-	unsigned int	dfc_width;	/* Width of flash controller(DWIDTH_C) */
-	struct pxa3xx_nand_timing *timing;	/* NAND Flash timing */
-};
-
-static struct pxa3xx_nand_timing timing[] = {
-	{ 40, 80, 60, 100, 80, 100, 90000, 400, 40, },
-	{ 10,  0, 20,  40, 30,  40, 11123, 110, 10, },
-	{ 10, 25, 15,  25, 15,  30, 25000,  60, 10, },
-	{ 10, 35, 15,  25, 15,  25, 25000,  60, 10, },
-};
-
-static struct pxa3xx_nand_flash builtin_flash_types[] = {
-	{ 0x46ec, 16, 16, &timing[1] },
-	{ 0xdaec,  8,  8, &timing[1] },
-	{ 0xd7ec,  8,  8, &timing[1] },
-	{ 0xa12c,  8,  8, &timing[2] },
-	{ 0xb12c, 16, 16, &timing[2] },
-	{ 0xdc2c,  8,  8, &timing[2] },
-	{ 0xcc2c, 16, 16, &timing[2] },
-	{ 0xba20, 16, 16, &timing[3] },
-};
-
-static int pxa3xx_ooblayout_ecc(struct mtd_info *mtd, int section,
-				struct mtd_oob_region *oobregion)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-	int nchunks = mtd->writesize / info->chunk_size;
-
-	if (section >= nchunks)
-		return -ERANGE;
-
-	oobregion->offset = ((info->ecc_size + info->spare_size) * section) +
-			    info->spare_size;
-	oobregion->length = info->ecc_size;
-
-	return 0;
-}
-
-static int pxa3xx_ooblayout_free(struct mtd_info *mtd, int section,
-				 struct mtd_oob_region *oobregion)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-	int nchunks = mtd->writesize / info->chunk_size;
-
-	if (section >= nchunks)
-		return -ERANGE;
-
-	if (!info->spare_size)
-		return 0;
-
-	oobregion->offset = section * (info->ecc_size + info->spare_size);
-	oobregion->length = info->spare_size;
-	if (!section) {
-		/*
-		 * Bootrom looks in bytes 0 & 5 for bad blocks for the
-		 * 4KB page / 4bit BCH combination.
-		 */
-		if (mtd->writesize == 4096 && info->chunk_size == 2048) {
-			oobregion->offset += 6;
-			oobregion->length -= 6;
-		} else {
-			oobregion->offset += 2;
-			oobregion->length -= 2;
-		}
-	}
-
-	return 0;
-}
-
-static const struct mtd_ooblayout_ops pxa3xx_ooblayout_ops = {
-	.ecc = pxa3xx_ooblayout_ecc,
-	.free = pxa3xx_ooblayout_free,
-};
-
-static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' };
-static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' };
-
-static struct nand_bbt_descr bbt_main_descr = {
-	.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
-		| NAND_BBT_2BIT | NAND_BBT_VERSION,
-	.offs =	8,
-	.len = 6,
-	.veroffs = 14,
-	.maxblocks = 8,		/* Last 8 blocks in each chip */
-	.pattern = bbt_pattern
-};
-
-static struct nand_bbt_descr bbt_mirror_descr = {
-	.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
-		| NAND_BBT_2BIT | NAND_BBT_VERSION,
-	.offs =	8,
-	.len = 6,
-	.veroffs = 14,
-	.maxblocks = 8,		/* Last 8 blocks in each chip */
-	.pattern = bbt_mirror_pattern
-};
-
-#define NDTR0_tCH(c)	(min((c), 7) << 19)
-#define NDTR0_tCS(c)	(min((c), 7) << 16)
-#define NDTR0_tWH(c)	(min((c), 7) << 11)
-#define NDTR0_tWP(c)	(min((c), 7) << 8)
-#define NDTR0_tRH(c)	(min((c), 7) << 3)
-#define NDTR0_tRP(c)	(min((c), 7) << 0)
-
-#define NDTR1_tR(c)	(min((c), 65535) << 16)
-#define NDTR1_tWHR(c)	(min((c), 15) << 4)
-#define NDTR1_tAR(c)	(min((c), 15) << 0)
-
-/* convert nano-seconds to nand flash controller clock cycles */
-#define ns2cycle(ns, clk)	(int)((ns) * (clk / 1000000) / 1000)
-
-static const struct of_device_id pxa3xx_nand_dt_ids[] = {
-	{
-		.compatible = "marvell,pxa3xx-nand",
-		.data       = (void *)PXA3XX_NAND_VARIANT_PXA,
-	},
-	{
-		.compatible = "marvell,armada370-nand",
-		.data       = (void *)PXA3XX_NAND_VARIANT_ARMADA370,
-	},
-	{
-		.compatible = "marvell,armada-8k-nand",
-		.data       = (void *)PXA3XX_NAND_VARIANT_ARMADA_8K,
-	},
-	{}
-};
-MODULE_DEVICE_TABLE(of, pxa3xx_nand_dt_ids);
-
-static enum pxa3xx_nand_variant
-pxa3xx_nand_get_variant(struct platform_device *pdev)
-{
-	const struct of_device_id *of_id =
-			of_match_device(pxa3xx_nand_dt_ids, &pdev->dev);
-	if (!of_id)
-		return PXA3XX_NAND_VARIANT_PXA;
-	return (enum pxa3xx_nand_variant)of_id->data;
-}
-
-static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host,
-				   const struct pxa3xx_nand_timing *t)
-{
-	struct pxa3xx_nand_info *info = host->info_data;
-	unsigned long nand_clk = clk_get_rate(info->clk);
-	uint32_t ndtr0, ndtr1;
-
-	ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) |
-		NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) |
-		NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) |
-		NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) |
-		NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) |
-		NDTR0_tRP(ns2cycle(t->tRP, nand_clk));
-
-	ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) |
-		NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) |
-		NDTR1_tAR(ns2cycle(t->tAR, nand_clk));
-
-	info->ndtr0cs0 = ndtr0;
-	info->ndtr1cs0 = ndtr1;
-	nand_writel(info, NDTR0CS0, ndtr0);
-	nand_writel(info, NDTR1CS0, ndtr1);
-}
-
-static void pxa3xx_nand_set_sdr_timing(struct pxa3xx_nand_host *host,
-				       const struct nand_sdr_timings *t)
-{
-	struct pxa3xx_nand_info *info = host->info_data;
-	struct nand_chip *chip = &host->chip;
-	unsigned long nand_clk = clk_get_rate(info->clk);
-	uint32_t ndtr0, ndtr1;
-
-	u32 tCH_min = DIV_ROUND_UP(t->tCH_min, 1000);
-	u32 tCS_min = DIV_ROUND_UP(t->tCS_min, 1000);
-	u32 tWH_min = DIV_ROUND_UP(t->tWH_min, 1000);
-	u32 tWP_min = DIV_ROUND_UP(t->tWC_min - t->tWH_min, 1000);
-	u32 tREH_min = DIV_ROUND_UP(t->tREH_min, 1000);
-	u32 tRP_min = DIV_ROUND_UP(t->tRC_min - t->tREH_min, 1000);
-	u32 tR = chip->chip_delay * 1000;
-	u32 tWHR_min = DIV_ROUND_UP(t->tWHR_min, 1000);
-	u32 tAR_min = DIV_ROUND_UP(t->tAR_min, 1000);
-
-	/* fallback to a default value if tR = 0 */
-	if (!tR)
-		tR = 20000;
-
-	ndtr0 = NDTR0_tCH(ns2cycle(tCH_min, nand_clk)) |
-		NDTR0_tCS(ns2cycle(tCS_min, nand_clk)) |
-		NDTR0_tWH(ns2cycle(tWH_min, nand_clk)) |
-		NDTR0_tWP(ns2cycle(tWP_min, nand_clk)) |
-		NDTR0_tRH(ns2cycle(tREH_min, nand_clk)) |
-		NDTR0_tRP(ns2cycle(tRP_min, nand_clk));
-
-	ndtr1 = NDTR1_tR(ns2cycle(tR, nand_clk)) |
-		NDTR1_tWHR(ns2cycle(tWHR_min, nand_clk)) |
-		NDTR1_tAR(ns2cycle(tAR_min, nand_clk));
-
-	info->ndtr0cs0 = ndtr0;
-	info->ndtr1cs0 = ndtr1;
-	nand_writel(info, NDTR0CS0, ndtr0);
-	nand_writel(info, NDTR1CS0, ndtr1);
-}
-
-static int pxa3xx_nand_init_timings_compat(struct pxa3xx_nand_host *host,
-					   unsigned int *flash_width,
-					   unsigned int *dfc_width)
-{
-	struct nand_chip *chip = &host->chip;
-	struct pxa3xx_nand_info *info = host->info_data;
-	const struct pxa3xx_nand_flash *f = NULL;
-	int i, id, ntypes;
-	u8 idbuf[2];
-
-	ntypes = ARRAY_SIZE(builtin_flash_types);
-
-	nand_readid_op(chip, 0, idbuf, sizeof(idbuf));
-	id = idbuf[0] | (idbuf[1] << 8);
-
-	for (i = 0; i < ntypes; i++) {
-		f = &builtin_flash_types[i];
-
-		if (f->chip_id == id)
-			break;
-	}
-
-	if (i == ntypes) {
-		dev_err(&info->pdev->dev, "Error: timings not found\n");
-		return -EINVAL;
-	}
-
-	pxa3xx_nand_set_timing(host, f->timing);
-
-	*flash_width = f->flash_width;
-	*dfc_width = f->dfc_width;
-
-	return 0;
-}
-
-static int pxa3xx_nand_init_timings_onfi(struct pxa3xx_nand_host *host,
-					 int mode)
-{
-	const struct nand_sdr_timings *timings;
-
-	mode = fls(mode) - 1;
-	if (mode < 0)
-		mode = 0;
-
-	timings = onfi_async_timing_mode_to_sdr_timings(mode);
-	if (IS_ERR(timings))
-		return PTR_ERR(timings);
-
-	pxa3xx_nand_set_sdr_timing(host, timings);
-
-	return 0;
-}
-
-static int pxa3xx_nand_init(struct pxa3xx_nand_host *host)
-{
-	struct nand_chip *chip = &host->chip;
-	struct pxa3xx_nand_info *info = host->info_data;
-	unsigned int flash_width = 0, dfc_width = 0;
-	int mode, err;
-
-	mode = onfi_get_async_timing_mode(chip);
-	if (mode == ONFI_TIMING_MODE_UNKNOWN) {
-		err = pxa3xx_nand_init_timings_compat(host, &flash_width,
-						      &dfc_width);
-		if (err)
-			return err;
-
-		if (flash_width == 16) {
-			info->reg_ndcr |= NDCR_DWIDTH_M;
-			chip->options |= NAND_BUSWIDTH_16;
-		}
-
-		info->reg_ndcr |= (dfc_width == 16) ? NDCR_DWIDTH_C : 0;
-	} else {
-		err = pxa3xx_nand_init_timings_onfi(host, mode);
-		if (err)
-			return err;
-	}
-
-	return 0;
-}
-
-/**
- * NOTE: it is a must to set ND_RUN firstly, then write
- * command buffer, otherwise, it does not work.
- * We enable all the interrupt at the same time, and
- * let pxa3xx_nand_irq to handle all logic.
- */
-static void pxa3xx_nand_start(struct pxa3xx_nand_info *info)
-{
-	uint32_t ndcr;
-
-	ndcr = info->reg_ndcr;
-
-	if (info->use_ecc) {
-		ndcr |= NDCR_ECC_EN;
-		if (info->ecc_bch)
-			nand_writel(info, NDECCCTRL, 0x1);
-	} else {
-		ndcr &= ~NDCR_ECC_EN;
-		if (info->ecc_bch)
-			nand_writel(info, NDECCCTRL, 0x0);
-	}
-
-	if (info->use_dma)
-		ndcr |= NDCR_DMA_EN;
-	else
-		ndcr &= ~NDCR_DMA_EN;
-
-	if (info->use_spare)
-		ndcr |= NDCR_SPARE_EN;
-	else
-		ndcr &= ~NDCR_SPARE_EN;
-
-	ndcr |= NDCR_ND_RUN;
-
-	/* clear status bits and run */
-	nand_writel(info, NDSR, NDSR_MASK);
-	nand_writel(info, NDCR, 0);
-	nand_writel(info, NDCR, ndcr);
-}
-
-static void pxa3xx_nand_stop(struct pxa3xx_nand_info *info)
-{
-	uint32_t ndcr;
-	int timeout = NAND_STOP_DELAY;
-
-	/* wait RUN bit in NDCR become 0 */
-	ndcr = nand_readl(info, NDCR);
-	while ((ndcr & NDCR_ND_RUN) && (timeout-- > 0)) {
-		ndcr = nand_readl(info, NDCR);
-		udelay(1);
-	}
-
-	if (timeout <= 0) {
-		ndcr &= ~NDCR_ND_RUN;
-		nand_writel(info, NDCR, ndcr);
-	}
-	if (info->dma_chan)
-		dmaengine_terminate_all(info->dma_chan);
-
-	/* clear status bits */
-	nand_writel(info, NDSR, NDSR_MASK);
-}
-
-static void __maybe_unused
-enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
-{
-	uint32_t ndcr;
-
-	ndcr = nand_readl(info, NDCR);
-	nand_writel(info, NDCR, ndcr & ~int_mask);
-}
-
-static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
-{
-	uint32_t ndcr;
-
-	ndcr = nand_readl(info, NDCR);
-	nand_writel(info, NDCR, ndcr | int_mask);
-}
-
-static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len)
-{
-	if (info->ecc_bch) {
-		u32 val;
-		int ret;
-
-		/*
-		 * According to the datasheet, when reading from NDDB
-		 * with BCH enabled, after each 32 bytes reads, we
-		 * have to make sure that the NDSR.RDDREQ bit is set.
-		 *
-		 * Drain the FIFO 8 32 bits reads at a time, and skip
-		 * the polling on the last read.
-		 */
-		while (len > 8) {
-			ioread32_rep(info->mmio_base + NDDB, data, 8);
-
-			ret = readl_relaxed_poll_timeout(info->mmio_base + NDSR, val,
-							 val & NDSR_RDDREQ, 1000, 5000);
-			if (ret) {
-				dev_err(&info->pdev->dev,
-					"Timeout on RDDREQ while draining the FIFO\n");
-				return;
-			}
-
-			data += 32;
-			len -= 8;
-		}
-	}
-
-	ioread32_rep(info->mmio_base + NDDB, data, len);
-}
-
-static void handle_data_pio(struct pxa3xx_nand_info *info)
-{
-	switch (info->state) {
-	case STATE_PIO_WRITING:
-		if (info->step_chunk_size)
-			writesl(info->mmio_base + NDDB,
-				info->data_buff + info->data_buff_pos,
-				DIV_ROUND_UP(info->step_chunk_size, 4));
-
-		if (info->step_spare_size)
-			writesl(info->mmio_base + NDDB,
-				info->oob_buff + info->oob_buff_pos,
-				DIV_ROUND_UP(info->step_spare_size, 4));
-		break;
-	case STATE_PIO_READING:
-		if (info->step_chunk_size)
-			drain_fifo(info,
-				   info->data_buff + info->data_buff_pos,
-				   DIV_ROUND_UP(info->step_chunk_size, 4));
-
-		if (info->step_spare_size)
-			drain_fifo(info,
-				   info->oob_buff + info->oob_buff_pos,
-				   DIV_ROUND_UP(info->step_spare_size, 4));
-		break;
-	default:
-		dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
-				info->state);
-		BUG();
-	}
-
-	/* Update buffer pointers for multi-page read/write */
-	info->data_buff_pos += info->step_chunk_size;
-	info->oob_buff_pos += info->step_spare_size;
-}
-
-static void pxa3xx_nand_data_dma_irq(void *data)
-{
-	struct pxa3xx_nand_info *info = data;
-	struct dma_tx_state state;
-	enum dma_status status;
-
-	status = dmaengine_tx_status(info->dma_chan, info->dma_cookie, &state);
-	if (likely(status == DMA_COMPLETE)) {
-		info->state = STATE_DMA_DONE;
-	} else {
-		dev_err(&info->pdev->dev, "DMA error on data channel\n");
-		info->retcode = ERR_DMABUSERR;
-	}
-	dma_unmap_sg(info->dma_chan->device->dev, &info->sg, 1, info->dma_dir);
-
-	nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ);
-	enable_int(info, NDCR_INT_MASK);
-}
-
-static void start_data_dma(struct pxa3xx_nand_info *info)
-{
-	enum dma_transfer_direction direction;
-	struct dma_async_tx_descriptor *tx;
-
-	switch (info->state) {
-	case STATE_DMA_WRITING:
-		info->dma_dir = DMA_TO_DEVICE;
-		direction = DMA_MEM_TO_DEV;
-		break;
-	case STATE_DMA_READING:
-		info->dma_dir = DMA_FROM_DEVICE;
-		direction = DMA_DEV_TO_MEM;
-		break;
-	default:
-		dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
-				info->state);
-		BUG();
-	}
-	info->sg.length = info->chunk_size;
-	if (info->use_spare)
-		info->sg.length += info->spare_size + info->ecc_size;
-	dma_map_sg(info->dma_chan->device->dev, &info->sg, 1, info->dma_dir);
-
-	tx = dmaengine_prep_slave_sg(info->dma_chan, &info->sg, 1, direction,
-				     DMA_PREP_INTERRUPT);
-	if (!tx) {
-		dev_err(&info->pdev->dev, "prep_slave_sg() failed\n");
-		return;
-	}
-	tx->callback = pxa3xx_nand_data_dma_irq;
-	tx->callback_param = info;
-	info->dma_cookie = dmaengine_submit(tx);
-	dma_async_issue_pending(info->dma_chan);
-	dev_dbg(&info->pdev->dev, "%s(dir=%d cookie=%x size=%u)\n",
-		__func__, direction, info->dma_cookie, info->sg.length);
-}
-
-static irqreturn_t pxa3xx_nand_irq_thread(int irq, void *data)
-{
-	struct pxa3xx_nand_info *info = data;
-
-	handle_data_pio(info);
-
-	info->state = STATE_CMD_DONE;
-	nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ);
-
-	return IRQ_HANDLED;
-}
-
-static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
-{
-	struct pxa3xx_nand_info *info = devid;
-	unsigned int status, is_completed = 0, is_ready = 0;
-	unsigned int ready, cmd_done;
-	irqreturn_t ret = IRQ_HANDLED;
-
-	if (info->cs == 0) {
-		ready           = NDSR_FLASH_RDY;
-		cmd_done        = NDSR_CS0_CMDD;
-	} else {
-		ready           = NDSR_RDY;
-		cmd_done        = NDSR_CS1_CMDD;
-	}
-
-	status = nand_readl(info, NDSR);
-
-	if (status & NDSR_UNCORERR)
-		info->retcode = ERR_UNCORERR;
-	if (status & NDSR_CORERR) {
-		info->retcode = ERR_CORERR;
-		if ((info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
-		     info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K) &&
-		    info->ecc_bch)
-			info->ecc_err_cnt = NDSR_ERR_CNT(status);
-		else
-			info->ecc_err_cnt = 1;
-
-		/*
-		 * Each chunk composing a page is corrected independently,
-		 * and we need to store maximum number of corrected bitflips
-		 * to return it to the MTD layer in ecc.read_page().
-		 */
-		info->max_bitflips = max_t(unsigned int,
-					   info->max_bitflips,
-					   info->ecc_err_cnt);
-	}
-	if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) {
-		/* whether use dma to transfer data */
-		if (info->use_dma) {
-			disable_int(info, NDCR_INT_MASK);
-			info->state = (status & NDSR_RDDREQ) ?
-				      STATE_DMA_READING : STATE_DMA_WRITING;
-			start_data_dma(info);
-			goto NORMAL_IRQ_EXIT;
-		} else {
-			info->state = (status & NDSR_RDDREQ) ?
-				      STATE_PIO_READING : STATE_PIO_WRITING;
-			ret = IRQ_WAKE_THREAD;
-			goto NORMAL_IRQ_EXIT;
-		}
-	}
-	if (status & cmd_done) {
-		info->state = STATE_CMD_DONE;
-		is_completed = 1;
-	}
-	if (status & ready) {
-		info->state = STATE_READY;
-		is_ready = 1;
-	}
-
-	/*
-	 * Clear all status bit before issuing the next command, which
-	 * can and will alter the status bits and will deserve a new
-	 * interrupt on its own. This lets the controller exit the IRQ
-	 */
-	nand_writel(info, NDSR, status);
-
-	if (status & NDSR_WRCMDREQ) {
-		status &= ~NDSR_WRCMDREQ;
-		info->state = STATE_CMD_HANDLE;
-
-		/*
-		 * Command buffer registers NDCB{0-2} (and optionally NDCB3)
-		 * must be loaded by writing directly either 12 or 16
-		 * bytes directly to NDCB0, four bytes at a time.
-		 *
-		 * Direct write access to NDCB1, NDCB2 and NDCB3 is ignored
-		 * but each NDCBx register can be read.
-		 */
-		nand_writel(info, NDCB0, info->ndcb0);
-		nand_writel(info, NDCB0, info->ndcb1);
-		nand_writel(info, NDCB0, info->ndcb2);
-
-		/* NDCB3 register is available in NFCv2 (Armada 370/XP SoC) */
-		if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
-		    info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K)
-			nand_writel(info, NDCB0, info->ndcb3);
-	}
-
-	if (is_completed)
-		complete(&info->cmd_complete);
-	if (is_ready)
-		complete(&info->dev_ready);
-NORMAL_IRQ_EXIT:
-	return ret;
-}
-
-static inline int is_buf_blank(uint8_t *buf, size_t len)
-{
-	for (; len > 0; len--)
-		if (*buf++ != 0xff)
-			return 0;
-	return 1;
-}
-
-static void set_command_address(struct pxa3xx_nand_info *info,
-		unsigned int page_size, uint16_t column, int page_addr)
-{
-	/* small page addr setting */
-	if (page_size < PAGE_CHUNK_SIZE) {
-		info->ndcb1 = ((page_addr & 0xFFFFFF) << 8)
-				| (column & 0xFF);
-
-		info->ndcb2 = 0;
-	} else {
-		info->ndcb1 = ((page_addr & 0xFFFF) << 16)
-				| (column & 0xFFFF);
-
-		if (page_addr & 0xFF0000)
-			info->ndcb2 = (page_addr & 0xFF0000) >> 16;
-		else
-			info->ndcb2 = 0;
-	}
-}
-
-static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
-{
-	struct pxa3xx_nand_host *host = info->host[info->cs];
-	struct mtd_info *mtd = nand_to_mtd(&host->chip);
-
-	/* reset data and oob column point to handle data */
-	info->buf_start		= 0;
-	info->buf_count		= 0;
-	info->data_buff_pos	= 0;
-	info->oob_buff_pos	= 0;
-	info->step_chunk_size   = 0;
-	info->step_spare_size   = 0;
-	info->cur_chunk         = 0;
-	info->use_ecc		= 0;
-	info->use_spare		= 1;
-	info->retcode		= ERR_NONE;
-	info->ecc_err_cnt	= 0;
-	info->ndcb3		= 0;
-	info->need_wait		= 0;
-
-	switch (command) {
-	case NAND_CMD_READ0:
-	case NAND_CMD_PAGEPROG:
-		info->use_ecc = 1;
-		break;
-	case NAND_CMD_PARAM:
-		info->use_spare = 0;
-		break;
-	default:
-		info->ndcb1 = 0;
-		info->ndcb2 = 0;
-		break;
-	}
-
-	/*
-	 * If we are about to issue a read command, or about to set
-	 * the write address, then clean the data buffer.
-	 */
-	if (command == NAND_CMD_READ0 ||
-	    command == NAND_CMD_READOOB ||
-	    command == NAND_CMD_SEQIN) {
-
-		info->buf_count = mtd->writesize + mtd->oobsize;
-		memset(info->data_buff, 0xFF, info->buf_count);
-	}
-
-}
-
-static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
-		int ext_cmd_type, uint16_t column, int page_addr)
-{
-	int addr_cycle, exec_cmd;
-	struct pxa3xx_nand_host *host;
-	struct mtd_info *mtd;
-
-	host = info->host[info->cs];
-	mtd = nand_to_mtd(&host->chip);
-	addr_cycle = 0;
-	exec_cmd = 1;
-
-	if (info->cs != 0)
-		info->ndcb0 = NDCB0_CSEL;
-	else
-		info->ndcb0 = 0;
-
-	if (command == NAND_CMD_SEQIN)
-		exec_cmd = 0;
-
-	addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles
-				    + host->col_addr_cycles);
-
-	switch (command) {
-	case NAND_CMD_READOOB:
-	case NAND_CMD_READ0:
-		info->buf_start = column;
-		info->ndcb0 |= NDCB0_CMD_TYPE(0)
-				| addr_cycle
-				| NAND_CMD_READ0;
-
-		if (command == NAND_CMD_READOOB)
-			info->buf_start += mtd->writesize;
-
-		if (info->cur_chunk < info->nfullchunks) {
-			info->step_chunk_size = info->chunk_size;
-			info->step_spare_size = info->spare_size;
-		} else {
-			info->step_chunk_size = info->last_chunk_size;
-			info->step_spare_size = info->last_spare_size;
-		}
-
-		/*
-		 * Multiple page read needs an 'extended command type' field,
-		 * which is either naked-read or last-read according to the
-		 * state.
-		 */
-		if (mtd->writesize == PAGE_CHUNK_SIZE) {
-			info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8);
-		} else if (mtd->writesize > PAGE_CHUNK_SIZE) {
-			info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8)
-					| NDCB0_LEN_OVRD
-					| NDCB0_EXT_CMD_TYPE(ext_cmd_type);
-			info->ndcb3 = info->step_chunk_size +
-				info->step_spare_size;
-		}
-
-		set_command_address(info, mtd->writesize, column, page_addr);
-		break;
-
-	case NAND_CMD_SEQIN:
-
-		info->buf_start = column;
-		set_command_address(info, mtd->writesize, 0, page_addr);
-
-		/*
-		 * Multiple page programming needs to execute the initial
-		 * SEQIN command that sets the page address.
-		 */
-		if (mtd->writesize > PAGE_CHUNK_SIZE) {
-			info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
-				| NDCB0_EXT_CMD_TYPE(ext_cmd_type)
-				| addr_cycle
-				| command;
-			exec_cmd = 1;
-		}
-		break;
-
-	case NAND_CMD_PAGEPROG:
-		if (is_buf_blank(info->data_buff,
-					(mtd->writesize + mtd->oobsize))) {
-			exec_cmd = 0;
-			break;
-		}
-
-		if (info->cur_chunk < info->nfullchunks) {
-			info->step_chunk_size = info->chunk_size;
-			info->step_spare_size = info->spare_size;
-		} else {
-			info->step_chunk_size = info->last_chunk_size;
-			info->step_spare_size = info->last_spare_size;
-		}
-
-		/* Second command setting for large pages */
-		if (mtd->writesize > PAGE_CHUNK_SIZE) {
-			/*
-			 * Multiple page write uses the 'extended command'
-			 * field. This can be used to issue a command dispatch
-			 * or a naked-write depending on the current stage.
-			 */
-			info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
-					| NDCB0_LEN_OVRD
-					| NDCB0_EXT_CMD_TYPE(ext_cmd_type);
-			info->ndcb3 = info->step_chunk_size +
-				      info->step_spare_size;
-
-			/*
-			 * This is the command dispatch that completes a chunked
-			 * page program operation.
-			 */
-			if (info->cur_chunk == info->ntotalchunks) {
-				info->ndcb0 = NDCB0_CMD_TYPE(0x1)
-					| NDCB0_EXT_CMD_TYPE(ext_cmd_type)
-					| command;
-				info->ndcb1 = 0;
-				info->ndcb2 = 0;
-				info->ndcb3 = 0;
-			}
-		} else {
-			info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
-					| NDCB0_AUTO_RS
-					| NDCB0_ST_ROW_EN
-					| NDCB0_DBC
-					| (NAND_CMD_PAGEPROG << 8)
-					| NAND_CMD_SEQIN
-					| addr_cycle;
-		}
-		break;
-
-	case NAND_CMD_PARAM:
-		info->buf_count = INIT_BUFFER_SIZE;
-		info->ndcb0 |= NDCB0_CMD_TYPE(0)
-				| NDCB0_ADDR_CYC(1)
-				| NDCB0_LEN_OVRD
-				| command;
-		info->ndcb1 = (column & 0xFF);
-		info->ndcb3 = INIT_BUFFER_SIZE;
-		info->step_chunk_size = INIT_BUFFER_SIZE;
-		break;
-
-	case NAND_CMD_READID:
-		info->buf_count = READ_ID_BYTES;
-		info->ndcb0 |= NDCB0_CMD_TYPE(3)
-				| NDCB0_ADDR_CYC(1)
-				| command;
-		info->ndcb1 = (column & 0xFF);
-
-		info->step_chunk_size = 8;
-		break;
-	case NAND_CMD_STATUS:
-		info->buf_count = 1;
-		info->ndcb0 |= NDCB0_CMD_TYPE(4)
-				| NDCB0_ADDR_CYC(1)
-				| command;
-
-		info->step_chunk_size = 8;
-		break;
-
-	case NAND_CMD_ERASE1:
-		info->ndcb0 |= NDCB0_CMD_TYPE(2)
-				| NDCB0_AUTO_RS
-				| NDCB0_ADDR_CYC(3)
-				| NDCB0_DBC
-				| (NAND_CMD_ERASE2 << 8)
-				| NAND_CMD_ERASE1;
-		info->ndcb1 = page_addr;
-		info->ndcb2 = 0;
-
-		break;
-	case NAND_CMD_RESET:
-		info->ndcb0 |= NDCB0_CMD_TYPE(5)
-				| command;
-
-		break;
-
-	case NAND_CMD_ERASE2:
-		exec_cmd = 0;
-		break;
-
-	default:
-		exec_cmd = 0;
-		dev_err(&info->pdev->dev, "non-supported command %x\n",
-				command);
-		break;
-	}
-
-	return exec_cmd;
-}
-
-static void nand_cmdfunc(struct mtd_info *mtd, unsigned command,
-			 int column, int page_addr)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-	int exec_cmd;
-
-	/*
-	 * if this is a x16 device ,then convert the input
-	 * "byte" address into a "word" address appropriate
-	 * for indexing a word-oriented device
-	 */
-	if (info->reg_ndcr & NDCR_DWIDTH_M)
-		column /= 2;
-
-	/*
-	 * There may be different NAND chip hooked to
-	 * different chip select, so check whether
-	 * chip select has been changed, if yes, reset the timing
-	 */
-	if (info->cs != host->cs) {
-		info->cs = host->cs;
-		nand_writel(info, NDTR0CS0, info->ndtr0cs0);
-		nand_writel(info, NDTR1CS0, info->ndtr1cs0);
-	}
-
-	prepare_start_command(info, command);
-
-	info->state = STATE_PREPARED;
-	exec_cmd = prepare_set_command(info, command, 0, column, page_addr);
-
-	if (exec_cmd) {
-		init_completion(&info->cmd_complete);
-		init_completion(&info->dev_ready);
-		info->need_wait = 1;
-		pxa3xx_nand_start(info);
-
-		if (!wait_for_completion_timeout(&info->cmd_complete,
-		    CHIP_DELAY_TIMEOUT)) {
-			dev_err(&info->pdev->dev, "Wait time out!!!\n");
-			/* Stop State Machine for next command cycle */
-			pxa3xx_nand_stop(info);
-		}
-	}
-	info->state = STATE_IDLE;
-}
-
-static void nand_cmdfunc_extended(struct mtd_info *mtd,
-				  const unsigned command,
-				  int column, int page_addr)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-	int exec_cmd, ext_cmd_type;
-
-	/*
-	 * if this is a x16 device then convert the input
-	 * "byte" address into a "word" address appropriate
-	 * for indexing a word-oriented device
-	 */
-	if (info->reg_ndcr & NDCR_DWIDTH_M)
-		column /= 2;
-
-	/*
-	 * There may be different NAND chip hooked to
-	 * different chip select, so check whether
-	 * chip select has been changed, if yes, reset the timing
-	 */
-	if (info->cs != host->cs) {
-		info->cs = host->cs;
-		nand_writel(info, NDTR0CS0, info->ndtr0cs0);
-		nand_writel(info, NDTR1CS0, info->ndtr1cs0);
-	}
-
-	/* Select the extended command for the first command */
-	switch (command) {
-	case NAND_CMD_READ0:
-	case NAND_CMD_READOOB:
-		ext_cmd_type = EXT_CMD_TYPE_MONO;
-		break;
-	case NAND_CMD_SEQIN:
-		ext_cmd_type = EXT_CMD_TYPE_DISPATCH;
-		break;
-	case NAND_CMD_PAGEPROG:
-		ext_cmd_type = EXT_CMD_TYPE_NAKED_RW;
-		break;
-	default:
-		ext_cmd_type = 0;
-		break;
-	}
-
-	prepare_start_command(info, command);
-
-	/*
-	 * Prepare the "is ready" completion before starting a command
-	 * transaction sequence. If the command is not executed the
-	 * completion will be completed, see below.
-	 *
-	 * We can do that inside the loop because the command variable
-	 * is invariant and thus so is the exec_cmd.
-	 */
-	info->need_wait = 1;
-	init_completion(&info->dev_ready);
-	do {
-		info->state = STATE_PREPARED;
-
-		exec_cmd = prepare_set_command(info, command, ext_cmd_type,
-					       column, page_addr);
-		if (!exec_cmd) {
-			info->need_wait = 0;
-			complete(&info->dev_ready);
-			break;
-		}
-
-		init_completion(&info->cmd_complete);
-		pxa3xx_nand_start(info);
-
-		if (!wait_for_completion_timeout(&info->cmd_complete,
-		    CHIP_DELAY_TIMEOUT)) {
-			dev_err(&info->pdev->dev, "Wait time out!!!\n");
-			/* Stop State Machine for next command cycle */
-			pxa3xx_nand_stop(info);
-			break;
-		}
-
-		/* Only a few commands need several steps */
-		if (command != NAND_CMD_PAGEPROG &&
-		    command != NAND_CMD_READ0    &&
-		    command != NAND_CMD_READOOB)
-			break;
-
-		info->cur_chunk++;
-
-		/* Check if the sequence is complete */
-		if (info->cur_chunk == info->ntotalchunks && command != NAND_CMD_PAGEPROG)
-			break;
-
-		/*
-		 * After a splitted program command sequence has issued
-		 * the command dispatch, the command sequence is complete.
-		 */
-		if (info->cur_chunk == (info->ntotalchunks + 1) &&
-		    command == NAND_CMD_PAGEPROG &&
-		    ext_cmd_type == EXT_CMD_TYPE_DISPATCH)
-			break;
-
-		if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) {
-			/* Last read: issue a 'last naked read' */
-			if (info->cur_chunk == info->ntotalchunks - 1)
-				ext_cmd_type = EXT_CMD_TYPE_LAST_RW;
-			else
-				ext_cmd_type = EXT_CMD_TYPE_NAKED_RW;
-
-		/*
-		 * If a splitted program command has no more data to transfer,
-		 * the command dispatch must be issued to complete.
-		 */
-		} else if (command == NAND_CMD_PAGEPROG &&
-			   info->cur_chunk == info->ntotalchunks) {
-				ext_cmd_type = EXT_CMD_TYPE_DISPATCH;
-		}
-	} while (1);
-
-	info->state = STATE_IDLE;
-}
-
-static int pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd,
-		struct nand_chip *chip, const uint8_t *buf, int oob_required,
-		int page)
-{
-	nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize);
-	chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
-
-	return nand_prog_page_end_op(chip);
-}
-
-static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
-		struct nand_chip *chip, uint8_t *buf, int oob_required,
-		int page)
-{
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-
-	nand_read_page_op(chip, page, 0, buf, mtd->writesize);
-	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
-
-	if (info->retcode == ERR_CORERR && info->use_ecc) {
-		mtd->ecc_stats.corrected += info->ecc_err_cnt;
-
-	} else if (info->retcode == ERR_UNCORERR) {
-		/*
-		 * for blank page (all 0xff), HW will calculate its ECC as
-		 * 0, which is different from the ECC information within
-		 * OOB, ignore such uncorrectable errors
-		 */
-		if (is_buf_blank(buf, mtd->writesize))
-			info->retcode = ERR_NONE;
-		else
-			mtd->ecc_stats.failed++;
-	}
-
-	return info->max_bitflips;
-}
-
-static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-	char retval = 0xFF;
-
-	if (info->buf_start < info->buf_count)
-		/* Has just send a new command? */
-		retval = info->data_buff[info->buf_start++];
-
-	return retval;
-}
-
-static u16 pxa3xx_nand_read_word(struct mtd_info *mtd)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-	u16 retval = 0xFFFF;
-
-	if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) {
-		retval = *((u16 *)(info->data_buff+info->buf_start));
-		info->buf_start += 2;
-	}
-	return retval;
-}
-
-static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-	int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
-
-	memcpy(buf, info->data_buff + info->buf_start, real_len);
-	info->buf_start += real_len;
-}
-
-static void pxa3xx_nand_write_buf(struct mtd_info *mtd,
-		const uint8_t *buf, int len)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-	int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
-
-	memcpy(info->data_buff + info->buf_start, buf, real_len);
-	info->buf_start += real_len;
-}
-
-static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip)
-{
-	return;
-}
-
-static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-
-	if (info->need_wait) {
-		info->need_wait = 0;
-		if (!wait_for_completion_timeout(&info->dev_ready,
-		    CHIP_DELAY_TIMEOUT)) {
-			dev_err(&info->pdev->dev, "Ready time out!!!\n");
-			return NAND_STATUS_FAIL;
-		}
-	}
-
-	/* pxa3xx_nand_send_command has waited for command complete */
-	if (this->state == FL_WRITING || this->state == FL_ERASING) {
-		if (info->retcode == ERR_NONE)
-			return 0;
-		else
-			return NAND_STATUS_FAIL;
-	}
-
-	return NAND_STATUS_READY;
-}
-
-static int pxa3xx_nand_config_ident(struct pxa3xx_nand_info *info)
-{
-	struct pxa3xx_nand_host *host = info->host[info->cs];
-	struct platform_device *pdev = info->pdev;
-	struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
-	const struct nand_sdr_timings *timings;
-
-	/* Configure default flash values */
-	info->chunk_size = PAGE_CHUNK_SIZE;
-	info->reg_ndcr = 0x0; /* enable all interrupts */
-	info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
-	info->reg_ndcr |= NDCR_RD_ID_CNT(READ_ID_BYTES);
-	info->reg_ndcr |= NDCR_SPARE_EN;
-
-	/* use the common timing to make a try */
-	timings = onfi_async_timing_mode_to_sdr_timings(0);
-	if (IS_ERR(timings))
-		return PTR_ERR(timings);
-
-	pxa3xx_nand_set_sdr_timing(host, timings);
-	return 0;
-}
-
-static void pxa3xx_nand_config_tail(struct pxa3xx_nand_info *info)
-{
-	struct pxa3xx_nand_host *host = info->host[info->cs];
-	struct nand_chip *chip = &host->chip;
-	struct mtd_info *mtd = nand_to_mtd(chip);
-
-	info->reg_ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0;
-	info->reg_ndcr |= (chip->page_shift == 6) ? NDCR_PG_PER_BLK : 0;
-	info->reg_ndcr |= (mtd->writesize == 2048) ? NDCR_PAGE_SZ : 0;
-}
-
-static void pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
-{
-	struct platform_device *pdev = info->pdev;
-	struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
-	uint32_t ndcr = nand_readl(info, NDCR);
-
-	/* Set an initial chunk size */
-	info->chunk_size = ndcr & NDCR_PAGE_SZ ? 2048 : 512;
-	info->reg_ndcr = ndcr &
-		~(NDCR_INT_MASK | NDCR_ND_ARB_EN | NFCV1_NDCR_ARB_CNTL);
-	info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
-	info->ndtr0cs0 = nand_readl(info, NDTR0CS0);
-	info->ndtr1cs0 = nand_readl(info, NDTR1CS0);
-}
-
-static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info)
-{
-	struct platform_device *pdev = info->pdev;
-	struct dma_slave_config	config;
-	dma_cap_mask_t mask;
-	struct pxad_param param;
-	int ret;
-
-	info->data_buff = kmalloc(info->buf_size, GFP_KERNEL);
-	if (info->data_buff == NULL)
-		return -ENOMEM;
-	if (use_dma == 0)
-		return 0;
-
-	ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
-	if (ret)
-		return ret;
-
-	sg_init_one(&info->sg, info->data_buff, info->buf_size);
-	dma_cap_zero(mask);
-	dma_cap_set(DMA_SLAVE, mask);
-	param.prio = PXAD_PRIO_LOWEST;
-	param.drcmr = info->drcmr_dat;
-	info->dma_chan = dma_request_slave_channel_compat(mask, pxad_filter_fn,
-							  &param, &pdev->dev,
-							  "data");
-	if (!info->dma_chan) {
-		dev_err(&pdev->dev, "unable to request data dma channel\n");
-		return -ENODEV;
-	}
-
-	memset(&config, 0, sizeof(config));
-	config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-	config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-	config.src_addr = info->mmio_phys + NDDB;
-	config.dst_addr = info->mmio_phys + NDDB;
-	config.src_maxburst = 32;
-	config.dst_maxburst = 32;
-	ret = dmaengine_slave_config(info->dma_chan, &config);
-	if (ret < 0) {
-		dev_err(&info->pdev->dev,
-			"dma channel configuration failed: %d\n",
-			ret);
-		return ret;
-	}
-
-	/*
-	 * Now that DMA buffers are allocated we turn on
-	 * DMA proper for I/O operations.
-	 */
-	info->use_dma = 1;
-	return 0;
-}
-
-static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info)
-{
-	if (info->use_dma) {
-		dmaengine_terminate_all(info->dma_chan);
-		dma_release_channel(info->dma_chan);
-	}
-	kfree(info->data_buff);
-}
-
-static int pxa_ecc_init(struct pxa3xx_nand_info *info,
-			struct mtd_info *mtd,
-			int strength, int ecc_stepsize, int page_size)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct nand_ecc_ctrl *ecc = &chip->ecc;
-
-	if (strength == 1 && ecc_stepsize == 512 && page_size == 2048) {
-		info->nfullchunks = 1;
-		info->ntotalchunks = 1;
-		info->chunk_size = 2048;
-		info->spare_size = 40;
-		info->ecc_size = 24;
-		ecc->mode = NAND_ECC_HW;
-		ecc->size = 512;
-		ecc->strength = 1;
-
-	} else if (strength == 1 && ecc_stepsize == 512 && page_size == 512) {
-		info->nfullchunks = 1;
-		info->ntotalchunks = 1;
-		info->chunk_size = 512;
-		info->spare_size = 8;
-		info->ecc_size = 8;
-		ecc->mode = NAND_ECC_HW;
-		ecc->size = 512;
-		ecc->strength = 1;
-
-	/*
-	 * Required ECC: 4-bit correction per 512 bytes
-	 * Select: 16-bit correction per 2048 bytes
-	 */
-	} else if (strength == 4 && ecc_stepsize == 512 && page_size == 2048) {
-		info->ecc_bch = 1;
-		info->nfullchunks = 1;
-		info->ntotalchunks = 1;
-		info->chunk_size = 2048;
-		info->spare_size = 32;
-		info->ecc_size = 32;
-		ecc->mode = NAND_ECC_HW;
-		ecc->size = info->chunk_size;
-		mtd_set_ooblayout(mtd, &pxa3xx_ooblayout_ops);
-		ecc->strength = 16;
-
-	} else if (strength == 4 && ecc_stepsize == 512 && page_size == 4096) {
-		info->ecc_bch = 1;
-		info->nfullchunks = 2;
-		info->ntotalchunks = 2;
-		info->chunk_size = 2048;
-		info->spare_size = 32;
-		info->ecc_size = 32;
-		ecc->mode = NAND_ECC_HW;
-		ecc->size = info->chunk_size;
-		mtd_set_ooblayout(mtd, &pxa3xx_ooblayout_ops);
-		ecc->strength = 16;
-
-	/*
-	 * Required ECC: 8-bit correction per 512 bytes
-	 * Select: 16-bit correction per 1024 bytes
-	 */
-	} else if (strength == 8 && ecc_stepsize == 512 && page_size == 4096) {
-		info->ecc_bch = 1;
-		info->nfullchunks = 4;
-		info->ntotalchunks = 5;
-		info->chunk_size = 1024;
-		info->spare_size = 0;
-		info->last_chunk_size = 0;
-		info->last_spare_size = 64;
-		info->ecc_size = 32;
-		ecc->mode = NAND_ECC_HW;
-		ecc->size = info->chunk_size;
-		mtd_set_ooblayout(mtd, &pxa3xx_ooblayout_ops);
-		ecc->strength = 16;
-	} else {
-		dev_err(&info->pdev->dev,
-			"ECC strength %d at page size %d is not supported\n",
-			strength, page_size);
-		return -ENODEV;
-	}
-
-	dev_info(&info->pdev->dev, "ECC strength %d, ECC step size %d\n",
-		 ecc->strength, ecc->size);
-	return 0;
-}
-
-static int pxa3xx_nand_scan(struct mtd_info *mtd)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
-	struct pxa3xx_nand_info *info = host->info_data;
-	struct platform_device *pdev = info->pdev;
-	struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
-	int ret;
-	uint16_t ecc_strength, ecc_step;
-
-	if (pdata->keep_config) {
-		pxa3xx_nand_detect_config(info);
-	} else {
-		ret = pxa3xx_nand_config_ident(info);
-		if (ret)
-			return ret;
-	}
-
-	if (info->reg_ndcr & NDCR_DWIDTH_M)
-		chip->options |= NAND_BUSWIDTH_16;
-
-	/* Device detection must be done with ECC disabled */
-	if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
-	    info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K)
-		nand_writel(info, NDECCCTRL, 0x0);
-
-	if (pdata->flash_bbt)
-		chip->bbt_options |= NAND_BBT_USE_FLASH;
-
-	chip->ecc.strength = pdata->ecc_strength;
-	chip->ecc.size = pdata->ecc_step_size;
-
-	ret = nand_scan_ident(mtd, 1, NULL);
-	if (ret)
-		return ret;
-
-	if (!pdata->keep_config) {
-		ret = pxa3xx_nand_init(host);
-		if (ret) {
-			dev_err(&info->pdev->dev, "Failed to init nand: %d\n",
-				ret);
-			return ret;
-		}
-	}
-
-	if (chip->bbt_options & NAND_BBT_USE_FLASH) {
-		/*
-		 * We'll use a bad block table stored in-flash and don't
-		 * allow writing the bad block marker to the flash.
-		 */
-		chip->bbt_options |= NAND_BBT_NO_OOB_BBM;
-		chip->bbt_td = &bbt_main_descr;
-		chip->bbt_md = &bbt_mirror_descr;
-	}
-
-	/*
-	 * If the page size is bigger than the FIFO size, let's check
-	 * we are given the right variant and then switch to the extended
-	 * (aka splitted) command handling,
-	 */
-	if (mtd->writesize > PAGE_CHUNK_SIZE) {
-		if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
-		    info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K) {
-			chip->cmdfunc = nand_cmdfunc_extended;
-		} else {
-			dev_err(&info->pdev->dev,
-				"unsupported page size on this variant\n");
-			return -ENODEV;
-		}
-	}
-
-	ecc_strength = chip->ecc.strength;
-	ecc_step = chip->ecc.size;
-	if (!ecc_strength || !ecc_step) {
-		ecc_strength = chip->ecc_strength_ds;
-		ecc_step = chip->ecc_step_ds;
-	}
-
-	/* Set default ECC strength requirements on non-ONFI devices */
-	if (ecc_strength < 1 && ecc_step < 1) {
-		ecc_strength = 1;
-		ecc_step = 512;
-	}
-
-	ret = pxa_ecc_init(info, mtd, ecc_strength,
-			   ecc_step, mtd->writesize);
-	if (ret)
-		return ret;
-
-	/* calculate addressing information */
-	if (mtd->writesize >= 2048)
-		host->col_addr_cycles = 2;
-	else
-		host->col_addr_cycles = 1;
-
-	/* release the initial buffer */
-	kfree(info->data_buff);
-
-	/* allocate the real data + oob buffer */
-	info->buf_size = mtd->writesize + mtd->oobsize;
-	ret = pxa3xx_nand_init_buff(info);
-	if (ret)
-		return ret;
-	info->oob_buff = info->data_buff + mtd->writesize;
-
-	if ((mtd->size >> chip->page_shift) > 65536)
-		host->row_addr_cycles = 3;
-	else
-		host->row_addr_cycles = 2;
-
-	if (!pdata->keep_config)
-		pxa3xx_nand_config_tail(info);
-
-	return nand_scan_tail(mtd);
-}
-
-static int alloc_nand_resource(struct platform_device *pdev)
-{
-	struct device_node *np = pdev->dev.of_node;
-	struct pxa3xx_nand_platform_data *pdata;
-	struct pxa3xx_nand_info *info;
-	struct pxa3xx_nand_host *host;
-	struct nand_chip *chip = NULL;
-	struct mtd_info *mtd;
-	struct resource *r;
-	int ret, irq, cs;
-
-	pdata = dev_get_platdata(&pdev->dev);
-	if (pdata->num_cs <= 0) {
-		dev_err(&pdev->dev, "invalid number of chip selects\n");
-		return -ENODEV;
-	}
-
-	info = devm_kzalloc(&pdev->dev,
-			    sizeof(*info) + sizeof(*host) * pdata->num_cs,
-			    GFP_KERNEL);
-	if (!info)
-		return -ENOMEM;
-
-	info->pdev = pdev;
-	info->variant = pxa3xx_nand_get_variant(pdev);
-	for (cs = 0; cs < pdata->num_cs; cs++) {
-		host = (void *)&info[1] + sizeof(*host) * cs;
-		chip = &host->chip;
-		nand_set_controller_data(chip, host);
-		mtd = nand_to_mtd(chip);
-		info->host[cs] = host;
-		host->cs = cs;
-		host->info_data = info;
-		mtd->dev.parent = &pdev->dev;
-		/* FIXME: all chips use the same device tree partitions */
-		nand_set_flash_node(chip, np);
-
-		nand_set_controller_data(chip, host);
-		chip->ecc.read_page	= pxa3xx_nand_read_page_hwecc;
-		chip->ecc.write_page	= pxa3xx_nand_write_page_hwecc;
-		chip->controller        = &info->controller;
-		chip->waitfunc		= pxa3xx_nand_waitfunc;
-		chip->select_chip	= pxa3xx_nand_select_chip;
-		chip->read_word		= pxa3xx_nand_read_word;
-		chip->read_byte		= pxa3xx_nand_read_byte;
-		chip->read_buf		= pxa3xx_nand_read_buf;
-		chip->write_buf		= pxa3xx_nand_write_buf;
-		chip->options		|= NAND_NO_SUBPAGE_WRITE;
-		chip->cmdfunc		= nand_cmdfunc;
-		chip->onfi_set_features	= nand_onfi_get_set_features_notsupp;
-		chip->onfi_get_features	= nand_onfi_get_set_features_notsupp;
-	}
-
-	nand_hw_control_init(chip->controller);
-	info->clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(info->clk)) {
-		ret = PTR_ERR(info->clk);
-		dev_err(&pdev->dev, "failed to get nand clock: %d\n", ret);
-		return ret;
-	}
-	ret = clk_prepare_enable(info->clk);
-	if (ret < 0)
-		return ret;
-
-	if (!np && use_dma) {
-		r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
-		if (r == NULL) {
-			dev_err(&pdev->dev,
-				"no resource defined for data DMA\n");
-			ret = -ENXIO;
-			goto fail_disable_clk;
-		}
-		info->drcmr_dat = r->start;
-	}
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0) {
-		dev_err(&pdev->dev, "no IRQ resource defined\n");
-		ret = -ENXIO;
-		goto fail_disable_clk;
-	}
-
-	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	info->mmio_base = devm_ioremap_resource(&pdev->dev, r);
-	if (IS_ERR(info->mmio_base)) {
-		ret = PTR_ERR(info->mmio_base);
-		dev_err(&pdev->dev, "failed to map register space: %d\n", ret);
-		goto fail_disable_clk;
-	}
-	info->mmio_phys = r->start;
-
-	/* Allocate a buffer to allow flash detection */
-	info->buf_size = INIT_BUFFER_SIZE;
-	info->data_buff = kmalloc(info->buf_size, GFP_KERNEL);
-	if (info->data_buff == NULL) {
-		ret = -ENOMEM;
-		goto fail_disable_clk;
-	}
-
-	/* initialize all interrupts to be disabled */
-	disable_int(info, NDSR_MASK);
-
-	ret = request_threaded_irq(irq, pxa3xx_nand_irq,
-				   pxa3xx_nand_irq_thread, IRQF_ONESHOT,
-				   pdev->name, info);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "failed to request IRQ: %d\n", ret);
-		goto fail_free_buf;
-	}
-
-	platform_set_drvdata(pdev, info);
-
-	return 0;
-
-fail_free_buf:
-	free_irq(irq, info);
-	kfree(info->data_buff);
-fail_disable_clk:
-	clk_disable_unprepare(info->clk);
-	return ret;
-}
-
-static int pxa3xx_nand_remove(struct platform_device *pdev)
-{
-	struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
-	struct pxa3xx_nand_platform_data *pdata;
-	int irq, cs;
-
-	if (!info)
-		return 0;
-
-	pdata = dev_get_platdata(&pdev->dev);
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq >= 0)
-		free_irq(irq, info);
-	pxa3xx_nand_free_buff(info);
-
-	/*
-	 * In the pxa3xx case, the DFI bus is shared between the SMC and NFC.
-	 * In order to prevent a lockup of the system bus, the DFI bus
-	 * arbitration is granted to SMC upon driver removal. This is done by
-	 * setting the x_ARB_CNTL bit, which also prevents the NAND to have
-	 * access to the bus anymore.
-	 */
-	nand_writel(info, NDCR,
-		    (nand_readl(info, NDCR) & ~NDCR_ND_ARB_EN) |
-		    NFCV1_NDCR_ARB_CNTL);
-	clk_disable_unprepare(info->clk);
-
-	for (cs = 0; cs < pdata->num_cs; cs++)
-		nand_release(nand_to_mtd(&info->host[cs]->chip));
-	return 0;
-}
-
-static int pxa3xx_nand_probe_dt(struct platform_device *pdev)
-{
-	struct pxa3xx_nand_platform_data *pdata;
-	struct device_node *np = pdev->dev.of_node;
-	const struct of_device_id *of_id =
-			of_match_device(pxa3xx_nand_dt_ids, &pdev->dev);
-
-	if (!of_id)
-		return 0;
-
-	/*
-	 * Some SoCs like A7k/A8k need to enable manually the NAND
-	 * controller to avoid being bootloader dependent. This is done
-	 * through the use of a single bit in the System Functions registers.
-	 */
-	if (pxa3xx_nand_get_variant(pdev) == PXA3XX_NAND_VARIANT_ARMADA_8K) {
-		struct regmap *sysctrl_base = syscon_regmap_lookup_by_phandle(
-			pdev->dev.of_node, "marvell,system-controller");
-		u32 reg;
-
-		if (IS_ERR(sysctrl_base))
-			return PTR_ERR(sysctrl_base);
-
-		regmap_read(sysctrl_base, GENCONF_SOC_DEVICE_MUX, &reg);
-		reg |= GENCONF_SOC_DEVICE_MUX_NFC_EN;
-		regmap_write(sysctrl_base, GENCONF_SOC_DEVICE_MUX, reg);
-	}
-
-	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
-	if (!pdata)
-		return -ENOMEM;
-
-	if (of_get_property(np, "marvell,nand-enable-arbiter", NULL))
-		pdata->enable_arbiter = 1;
-	if (of_get_property(np, "marvell,nand-keep-config", NULL))
-		pdata->keep_config = 1;
-	of_property_read_u32(np, "num-cs", &pdata->num_cs);
-
-	pdev->dev.platform_data = pdata;
-
-	return 0;
-}
-
-static int pxa3xx_nand_probe(struct platform_device *pdev)
-{
-	struct pxa3xx_nand_platform_data *pdata;
-	struct pxa3xx_nand_info *info;
-	int ret, cs, probe_success, dma_available;
-
-	dma_available = IS_ENABLED(CONFIG_ARM) &&
-		(IS_ENABLED(CONFIG_ARCH_PXA) || IS_ENABLED(CONFIG_ARCH_MMP));
-	if (use_dma && !dma_available) {
-		use_dma = 0;
-		dev_warn(&pdev->dev,
-			 "This platform can't do DMA on this device\n");
-	}
-
-	ret = pxa3xx_nand_probe_dt(pdev);
-	if (ret)
-		return ret;
-
-	pdata = dev_get_platdata(&pdev->dev);
-	if (!pdata) {
-		dev_err(&pdev->dev, "no platform data defined\n");
-		return -ENODEV;
-	}
-
-	ret = alloc_nand_resource(pdev);
-	if (ret)
-		return ret;
-
-	info = platform_get_drvdata(pdev);
-	probe_success = 0;
-	for (cs = 0; cs < pdata->num_cs; cs++) {
-		struct mtd_info *mtd = nand_to_mtd(&info->host[cs]->chip);
-
-		/*
-		 * The mtd name matches the one used in 'mtdparts' kernel
-		 * parameter. This name cannot be changed or otherwise
-		 * user's mtd partitions configuration would get broken.
-		 */
-		mtd->name = "pxa3xx_nand-0";
-		info->cs = cs;
-		ret = pxa3xx_nand_scan(mtd);
-		if (ret) {
-			dev_warn(&pdev->dev, "failed to scan nand at cs %d\n",
-				cs);
-			continue;
-		}
-
-		ret = mtd_device_register(mtd, pdata->parts[cs],
-					  pdata->nr_parts[cs]);
-		if (!ret)
-			probe_success = 1;
-	}
-
-	if (!probe_success) {
-		pxa3xx_nand_remove(pdev);
-		return -ENODEV;
-	}
-
-	return 0;
-}
-
-#ifdef CONFIG_PM
-static int pxa3xx_nand_suspend(struct device *dev)
-{
-	struct pxa3xx_nand_info *info = dev_get_drvdata(dev);
-
-	if (info->state) {
-		dev_err(dev, "driver busy, state = %d\n", info->state);
-		return -EAGAIN;
-	}
-
-	clk_disable(info->clk);
-	return 0;
-}
-
-static int pxa3xx_nand_resume(struct device *dev)
-{
-	struct pxa3xx_nand_info *info = dev_get_drvdata(dev);
-	int ret;
-
-	ret = clk_enable(info->clk);
-	if (ret < 0)
-		return ret;
-
-	/* We don't want to handle interrupt without calling mtd routine */
-	disable_int(info, NDCR_INT_MASK);
-
-	/*
-	 * Directly set the chip select to a invalid value,
-	 * then the driver would reset the timing according
-	 * to current chip select at the beginning of cmdfunc
-	 */
-	info->cs = 0xff;
-
-	/*
-	 * As the spec says, the NDSR would be updated to 0x1800 when
-	 * doing the nand_clk disable/enable.
-	 * To prevent it damaging state machine of the driver, clear
-	 * all status before resume
-	 */
-	nand_writel(info, NDSR, NDSR_MASK);
-
-	return 0;
-}
-#else
-#define pxa3xx_nand_suspend	NULL
-#define pxa3xx_nand_resume	NULL
-#endif
-
-static const struct dev_pm_ops pxa3xx_nand_pm_ops = {
-	.suspend	= pxa3xx_nand_suspend,
-	.resume		= pxa3xx_nand_resume,
-};
-
-static struct platform_driver pxa3xx_nand_driver = {
-	.driver = {
-		.name	= "pxa3xx-nand",
-		.of_match_table = pxa3xx_nand_dt_ids,
-		.pm	= &pxa3xx_nand_pm_ops,
-	},
-	.probe		= pxa3xx_nand_probe,
-	.remove		= pxa3xx_nand_remove,
-};
-
-module_platform_driver(pxa3xx_nand_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("PXA3xx NAND controller driver");