Message ID | 20171117110912.24305-1-s.hauer@pengutronix.de |
---|---|
State | Accepted |
Delegated to: | Boris Brezillon |
Headers | show |
Series | mtd: nand: gpmi-nand: Remove wrong Kconfig help text | expand |
On Fri, Nov 17, 2017 at 9:09 AM, Sascha Hauer <s.hauer@pengutronix.de> wrote: > The GPMI nand Kconfig help texts mentions that the GPMI nand driver > might conflict with SD cards. The only conflict there might really > be is that both controllers use the same pins, but this is resolved > by the pincontroller setup in the device tree. In any way the GPMI > driver can safely be enabled, the text is just wrong. Remove it. > > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
On Fri, 17 Nov 2017 12:09:12 +0100 Sascha Hauer <s.hauer@pengutronix.de> wrote: > The GPMI nand Kconfig help texts mentions that the GPMI nand driver > might conflict with SD cards. The only conflict there might really > be is that both controllers use the same pins, but this is resolved > by the pincontroller setup in the device tree. In any way the GPMI > driver can safely be enabled, the text is just wrong. Remove it. Applied. Thanks, Boris > > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> > --- > drivers/mtd/nand/Kconfig | 4 +--- > 1 file changed, 1 insertion(+), 3 deletions(-) > > diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig > index 3f2036f31da4..8f4c288cf9f1 100644 > --- a/drivers/mtd/nand/Kconfig > +++ b/drivers/mtd/nand/Kconfig > @@ -373,9 +373,7 @@ config MTD_NAND_GPMI_NAND > Enables NAND Flash support for IMX23, IMX28 or IMX6. > The GPMI controller is very powerful, with the help of BCH > module, it can do the hardware ECC. The GPMI supports several > - NAND flashs at the same time. The GPMI may conflicts with other > - block, such as SD card. So pay attention to it when you enable > - the GPMI. > + NAND flashs at the same time. > > config MTD_NAND_BRCMNAND > tristate "Broadcom STB NAND controller"
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 3f2036f31da4..8f4c288cf9f1 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -373,9 +373,7 @@ config MTD_NAND_GPMI_NAND Enables NAND Flash support for IMX23, IMX28 or IMX6. The GPMI controller is very powerful, with the help of BCH module, it can do the hardware ECC. The GPMI supports several - NAND flashs at the same time. The GPMI may conflicts with other - block, such as SD card. So pay attention to it when you enable - the GPMI. + NAND flashs at the same time. config MTD_NAND_BRCMNAND tristate "Broadcom STB NAND controller"
The GPMI nand Kconfig help texts mentions that the GPMI nand driver might conflict with SD cards. The only conflict there might really be is that both controllers use the same pins, but this is resolved by the pincontroller setup in the device tree. In any way the GPMI driver can safely be enabled, the text is just wrong. Remove it. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> --- drivers/mtd/nand/Kconfig | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)