diff --git a/lib/e2p/parse_num.c b/lib/e2p/parse_num.c
index 83a329a..5e7924b 100644
--- a/lib/e2p/parse_num.c
+++ b/lib/e2p/parse_num.c
@@ -10,6 +10,7 @@
  */
 
 #include "e2p.h"
+#include "../misc/nls-enable.h"
 
 #include <stdlib.h>
 
@@ -37,6 +38,14 @@ unsigned long long parse_num_blocks2(const char *arg, int log_block_size)
 		num >>= (1+log_block_size);
 		break;
 	case '\0':
+	case 'b':
+		if (!log_block_size) {
+			fprintf(stderr,
+				_("Warning: You can not specify blocks count "
+				"without specifying block size '-b'. Will "
+				"assume kilobytes instead of blocks count!.\n"
+				));
+		}
 		break;
 	default:
 		return 0;
diff --git a/misc/mke2fs.8.in b/misc/mke2fs.8.in
index 2eead17..e093be0 100644
--- a/misc/mke2fs.8.in
+++ b/misc/mke2fs.8.in
@@ -108,7 +108,7 @@ mke2fs \- create an ext2/ext3/ext4 filesystem
 ]
 .I device
 [
-.I blocks-count
+.I filesystem-size
 ]
 @JDEV@.sp
 @JDEV@.B "mke2fs \-O journal_dev"
@@ -136,7 +136,7 @@ mke2fs \- create an ext2/ext3/ext4 filesystem
 @JDEV@]
 @JDEV@.I external-journal
 @JDEV@[
-@JDEV@.I blocks-count
+@JDEV@.I filesystem-size
 @JDEV@]
 .SH DESCRIPTION
 .B mke2fs
@@ -145,10 +145,30 @@ partition.
 .I device
 is the special file corresponding to the device (e.g
 .IR /dev/hdXX ).
-.I blocks-count
-is the number of blocks on the device.  If omitted,
-.B mke2fs
-automagically figures the file system size.  If called as
+.I filesystem-size
+is the size of the filesystem you want to create.
+If no units are specified, the units of the
+.I filesystem-size
+parameter shall be the blocks count of the filesystem. Keep in mind that
+you can not specify
+.I filesystem-size
+in blocks count without specifying the blocksize as well. This will be
+allowed for now (1024 byte blocks will be assumed)
+due to compatibility reasons, however it may be restricted
+in the future.
+Optionally, the
+.I filesystem-size
+parameter may be suffixed by one of the following units
+designators: 'b', 's', 'K', 'M', 'G', or 'T',
+for blocks count, 512 byte sectors, KiB (2^10 Bytes), MiB (2^20 Bytes),
+GiB (2^30 Bytes), or TiB (2^40 Bytes) respectively, which are binary (power-of-2),
+not decimal, units. The
+.I filesystem-size
+may never be larger than the size of the partition.
+If
+.I filesystem-size
+parameter is not specified, it will default to the size of the partition.
+If called as
 .B mkfs.ext3
 a journal is created as if the
 .B \-j
diff --git a/resize/resize2fs.8.in b/resize/resize2fs.8.in
index e02345d..769fd14 100644
--- a/resize/resize2fs.8.in
+++ b/resize/resize2fs.8.in
@@ -38,27 +38,20 @@ The
 parameter specifies the requested new size of the filesystem.
 If no units are specified, the units of the
 .I size
-parameter shall be the filesystem blocksize of the filesystem.
+parameter shall be the blocks count of the filesystem.
 Optionally, the 
 .I size
-parameter may be suffixed by one of the following the units 
-designators: 's', 'K', 'M', or 'G',
-for 512 byte sectors, kilobytes, megabytes, or gigabytes, respectively.
-The 
+parameter may be suffixed by one of the following the units
+designators: 'b', 's', 'K', 'M', 'G', or 'T',
+for blocks count, 512 byte sectors, KiB (2^10 Bytes), MiB (2^20 Bytes),
+GiB (2^30 Bytes), or TiB (2^40 Bytes) respectively, which are binary (power-of-2),
+not decimal, units. The
 .I size
 of the filesystem may never be larger than the size of the partition.
 If 
 .I size
 parameter is not specified, it will default to the size of the partition.
 .PP
-Note: when kilobytes is used above, I mean
-.IR real ,
-power-of-2 kilobytes, (i.e., 1024 bytes), which some politically correct
-folks insist should be the stupid-sounding ``kibibytes''.  The same
-holds true for megabytes, also sometimes known as ``mebibytes'', or
-gigabytes, as the amazingly silly ``gibibytes''.  Makes you want to
-gibber, doesn't it?
-.PP
 The
 .B resize2fs
 program does not manipulate the size of partitions.  If you wish to enlarge