@@ -2264,36 +2264,19 @@ static int fm10k_handle_resume(struct fm10k_intfc *interface)
#ifdef CONFIG_PM
/**
- * fm10k_resume - Restore device to pre-sleep state
- * @pdev: PCI device information struct
+ * fm10k_resume - Generic PM resume hook
+ * @dev: generic device structure
*
- * fm10k_resume is called after the system has powered back up from a sleep
- * state and is ready to resume operation. This function is meant to restore
- * the device back to its pre-sleep state.
+ * Generic PM hook used when waking the device from a low power state after
+ * suspend or hibernation. This function does not need to handle lower PCIe
+ * device state as the stack takes care of that for us.
**/
-static int fm10k_resume(struct pci_dev *pdev)
+static int fm10k_resume(struct device *dev)
{
- struct fm10k_intfc *interface = pci_get_drvdata(pdev);
+ struct fm10k_intfc *interface = pci_get_drvdata(to_pci_dev(dev));
struct net_device *netdev = interface->netdev;
struct fm10k_hw *hw = &interface->hw;
- u32 err;
-
- pci_set_power_state(pdev, PCI_D0);
- pci_restore_state(pdev);
-
- /* pci_restore_state clears dev->state_saved so call
- * pci_save_state to restore it.
- */
- pci_save_state(pdev);
-
- err = pci_enable_device_mem(pdev);
- if (err) {
- dev_err(&pdev->dev, "Cannot enable PCI device from suspend\n");
- return err;
- }
- pci_set_master(pdev);
-
- pci_wake_from_d3(pdev, false);
+ int err;
/* refresh hw_addr in case it was dropped */
hw->hw_addr = interface->uc_addr;
@@ -2308,36 +2291,27 @@ static int fm10k_resume(struct pci_dev *pdev)
}
/**
- * fm10k_suspend - Prepare the device for a system sleep state
- * @pdev: PCI device information struct
+ * fm10k_suspend - Generic PM suspend hook
+ * @dev: generic device structure
*
- * fm10k_suspend is meant to shutdown the device prior to the system entering
- * a sleep state. The fm10k hardware does not support wake on lan so the
- * driver simply needs to shut down the device so it is in a low power state.
+ * Generic PM hook used when setting the device into a low power state for
+ * system suspend or hibernation. This function does not need to handle lower
+ * PCIe device state as the stack takes care of that for us.
**/
-static int fm10k_suspend(struct pci_dev *pdev,
- pm_message_t __always_unused state)
+static int fm10k_suspend(struct device *dev)
{
- struct fm10k_intfc *interface = pci_get_drvdata(pdev);
+ struct fm10k_intfc *interface = pci_get_drvdata(to_pci_dev(dev));
struct net_device *netdev = interface->netdev;
- int err = 0;
netif_device_detach(netdev);
fm10k_prepare_suspend(interface);
- err = pci_save_state(pdev);
- if (err)
- return err;
-
- pci_disable_device(pdev);
- pci_wake_from_d3(pdev, false);
- pci_set_power_state(pdev, PCI_D3hot);
-
return 0;
}
#endif /* CONFIG_PM */
+
/**
* fm10k_io_error_detected - called when PCI error is detected
* @pdev: Pointer to PCI device
@@ -2447,15 +2421,18 @@ static const struct pci_error_handlers fm10k_err_handler = {
.reset_done = fm10k_io_reset_done,
};
+static SIMPLE_DEV_PM_OPS(fm10k_pm_ops, fm10k_suspend, fm10k_resume);
+
static struct pci_driver fm10k_driver = {
.name = fm10k_driver_name,
.id_table = fm10k_pci_tbl,
.probe = fm10k_probe,
.remove = fm10k_remove,
#ifdef CONFIG_PM
- .suspend = fm10k_suspend,
- .resume = fm10k_resume,
-#endif
+ .driver = {
+ .pm = &fm10k_pm_ops,
+ },
+#endif /* CONFIG_PM */
.sriov_configure = fm10k_iov_configure,
.err_handler = &fm10k_err_handler
};