@@ -82,6 +82,10 @@ broadway)
set_usb_led "$board:red:diskmounted"
set_wifi_led "$board:red:wps_active"
;;
+c108)
+ ucidef_set_led_netdev "lan" "lan" "$board:green:lan" "eth0"
+ ucidef_set_led_netdev "modem" "modem" "$board:green:modem" "wwan0"
+ ;;
c20i)
ucidef_set_led_switch "lan" "lan" "$board:blue:lan" "switch0" "0x1e"
ucidef_set_led_switch "wan" "wan" "$board:blue:wan" "switch0" "0x01"
@@ -217,6 +217,7 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
;;
+ c108|\
cf-wr800n)
ucidef_add_switch "switch0" \
"4:lan" "6t@eth0"
@@ -103,6 +103,9 @@ get_status_led() {
wrh-300cr)
status_led="$board:green:wps"
;;
+ c108)
+ status_led="$board:green:lan"
+ ;;
cf-wr800n|\
psg1208)
status_led="$board:white:wps"
@@ -85,6 +85,9 @@ ramips_board_detect() {
*"Broadway")
name="broadway"
;;
+ *"C108")
+ name="c108"
+ ;;
*"C20i")
name="c20i"
;;
@@ -29,6 +29,7 @@ platform_check_image() {
awm002-evb-8M|\
bc2|\
broadway|\
+ c108|\
carambola|\
cf-wr800n|\
cs-qr10|\
new file mode 100644
@@ -0,0 +1,177 @@
+/*
+ * BSD LICENSE
+ *
+ * Copyright(c) 2017 Kristian Evensen <kristian.evensen@gmail.com>.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "hnet,c108", "ralink,mt7620a-soc";
+ model = "HNET C108";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ power_modem {
+ gpio-export,name = "power_modem";
+ gpio-export,output = <1>;
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ sdcard {
+ label = "c108:green:sdcard";
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ };
+
+ modem_green {
+ label = "c108:green:modem";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ };
+
+ modem_red {
+ label = "c108:red:modem";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+
+ lan_red {
+ label = "c108:red:lan";
+ gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan_green {
+ label = "c108:green:lan";
+ gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&gpio2 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ en25q128@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition@50000 {
+ label = "firmware";
+ reg = <0x50000 0xfb0000>;
+ };
+ };
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&ehci {
+ status = "okay";
+};
+
+&ohci {
+ status = "okay";
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0x28>;
+};
+
+&wmac {
+ ralink,mtd-eeprom = <&factory 0>;
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ default {
+ ralink,group = "i2c", "uartf", "spi refclk", "ephy";
+ ralink,function = "gpio";
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
@@ -62,6 +62,14 @@ define Device/ArcherMR200
endef
TARGET_DEVICES += ArcherMR200
+define Device/c108
+ DTS := C108
+ IMAGE_SIZE := 16777216
+ DEVICE_TITLE := HNET C108
+ DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620
+endef
+TARGET_DEVICES += c108
+
define Device/cf-wr800n
DTS := CF-WR800N
DEVICE_TITLE := Comfast CF-WR800N
The HNET C108 (http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a mifi based on MT7602A, which has the following specifications: * CPU: MT7620A * 1x 10/100Mbps Ethernet. * 16 MB Flash. * 64 MB RAM. * 1x USB 2.0 port. Only power is connected, this port is meant for charging other devices. * 1x mini-PCIe slots. * 1x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. * 6000 mAh battery. * 5x controllable LEDs. Works: * Wifi. * Switch. * mini-PCIe slot. Only tested with a USB device (a modem). * SIM slot. * Sysupgrade. * Button (reset). Not working (also applies to the factory firmware): * Wifi LED. It is always switched on, there is no relation to the up/down state or activity of the wireless interface. Not tested: * SD card reader. Notes: * The C108 has no dedicated status LED. I therefore set the LAN LED as status LED. Installation: The router comes pre-installed with OpenWRT, including a variant of Luci. The initial firmware install can be done through this UI, following normal procedure. I.e., access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. Recovery: If you brick the device, the C108 supports recovery using TFTP. Keep the reset button pressed for ~5sec when booting to trigger TFTP. Set the address of the network interface on your machine to 10.10.10.3/24, and rename your image file to Kernal.bin. v3->v4: * Fixed typo in diag.sh. v2->v3: * Update description of USB port after discussing with factory. * Updated Wifi LED description (thanks Mathias Kresin). * Removed non-used GPIO bank and invalid portmap from dts, as well as using absolute value for the gpio output value (thanks Mathias Kresin). * Update size of firmware parition in Makefile to match factory firmware (thanks Mathias Kresin). * Respect ordering in diag.sh (thanks Mathias Kresin). v1->v2: * Update "Not working" based on more testing with factory firmware. * Changed offset of LAN MAC address. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> --- target/linux/ramips/base-files/etc/board.d/01_leds | 4 + .../linux/ramips/base-files/etc/board.d/02_network | 1 + target/linux/ramips/base-files/etc/diag.sh | 3 + target/linux/ramips/base-files/lib/ramips.sh | 3 + .../ramips/base-files/lib/upgrade/platform.sh | 1 + target/linux/ramips/dts/C108.dts | 177 +++++++++++++++++++++ target/linux/ramips/image/mt7620.mk | 8 + 7 files changed, 197 insertions(+) create mode 100644 target/linux/ramips/dts/C108.dts