diff mbox

[Natty,1/2] omap3: beaglexm: fix DVI initialization

Message ID 1296187838-23021-2-git-send-email-ricardo.salveti@canonical.com
State Accepted
Delegated to: Tim Gardner
Headers show

Commit Message

Ricardo Salveti de Araujo Jan. 28, 2011, 4:10 a.m. UTC 
Function beagle_twl_gpio_setup is called after beagle_display_init, what
makes lets reset_gpio with an invalid value at the time it request the
gpio. As a side effect the DVI reset GPIO is not properly set.

Also removing old code that power down DVI in a hardcoded way, as it's
not necessary anymore.

Tested with Beagle-xM and C4.

Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
---
 arch/arm/mach-omap2/board-omap3beagle.c |   17 ++++++-----------
 1 files changed, 6 insertions(+), 11 deletions(-)
diff mbox

Patch

diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 685ac06..c8ab478 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -248,6 +248,12 @@  static void __init beagle_display_init(void)
 {
 	int r;
 
+	/* DVI reset GPIO is different between beagle revisions */
+	if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM)
+		beagle_dvi_device.reset_gpio = 129;
+	else
+		beagle_dvi_device.reset_gpio = 170;
+
 	r = gpio_request(beagle_dvi_device.reset_gpio, "DVI reset");
 	if (r < 0) {
 		printk(KERN_ERR "Unable to get DVI reset GPIO\n");
@@ -324,12 +330,6 @@  static int beagle_twl_gpio_setup(struct device *dev,
 	else
 		gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
 
-	/* DVI reset GPIO is different between beagle revisions */
-	if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM)
-		beagle_dvi_device.reset_gpio = 129;
-	else
-		beagle_dvi_device.reset_gpio = 170;
-
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
 
@@ -620,11 +620,6 @@  static void __init omap3_beagle_init(void)
 			ARRAY_SIZE(omap3_beagle_devices));
 	omap_serial_init();
 
-	omap_mux_init_gpio(170, OMAP_PIN_INPUT);
-	gpio_request(170, "DVI_nPD");
-	/* REVISIT leave DVI powered down until it's needed ... */
-	gpio_direction_output(170, true);
-
 	usb_musb_init(&musb_board_data);
 	usb_ehci_init(&ehci_pdata);
 	omap3beagle_flash_init();