diff mbox

[v4,17/20] dt-bindings: qcom_nandc: IPQ4019 QPIC NAND documentation

Message ID 1502451575-15712-18-git-send-email-absahu@codeaurora.org
State Superseded
Delegated to: Boris Brezillon
Headers show

Commit Message

Abhishek Sahu Aug. 11, 2017, 11:39 a.m. UTC 
1. Qualcom IPQ4019 SoC uses QPIC NAND controller version 1.4.0
   which uses BAM DMA Engine while IPQ806x uses EBI2 NAND
   which uses ADM DMA Engine.
2. QPIC NAND will 3 BAM channels: command, data tx and data rx
   while EBI2 NAND uses only single ADM channel.
3. CRCI is only required for ADM DMA and its not required for
   BAM DMA.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
---
 .../devicetree/bindings/mtd/qcom_nandc.txt         | 55 +++++++++++++++++++++-
 1 file changed, 54 insertions(+), 1 deletion(-)
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
index f475b65..d93b952 100644
--- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
+++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
@@ -1,11 +1,18 @@ 
 * Qualcomm NAND controller
 
 Required properties:
-- compatible:		should be "qcom,ipq806x-nand"
+- compatible:		must be one of the following:
+    * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x
+			    SoC and it uses ADM DMA
+    * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in
+                            IPQ4019 SoC and it uses BAM DMA
+
 - reg:			MMIO address range
 - clocks:		must contain core clock and always on clock
 - clock-names:		must contain "core" for the core clock and "aon" for the
 			always on clock
+
+EBI2 specific properties:
 - dmas:			DMA specifier, consisting of a phandle to the ADM DMA
 			controller node and the channel number to be used for
 			NAND. Refer to dma.txt and qcom_adm.txt for more details
@@ -16,6 +23,12 @@  Required properties:
 - qcom,data-crci:	must contain the ADM data type CRCI block instance
 			number specified for the NAND controller on the given
 			platform
+
+QPIC specific properties:
+- dmas:			DMA specifier, consisting of a phandle to the BAM DMA
+			and the channel number to be used for NAND. Refer to
+			dma.txt, qcom_bam_dma.txt for more details
+- dma-names:		must contain all 3 channel names : "tx", "rx", "cmd"
 - #address-cells:	<1> - subnodes give the chip-select number
 - #size-cells:		<0>
 
@@ -82,3 +95,43 @@  nand-controller@1ac00000 {
 		};
 	};
 };
+
+nand-controller@79b0000 {
+	compatible = "qcom,ipq4019-nand";
+	reg = <0x79b0000 0x1000>;
+
+	clocks = <&gcc GCC_QPIC_CLK>,
+		<&gcc GCC_QPIC_AHB_CLK>;
+	clock-names = "core", "aon";
+
+	dmas = <&qpicbam 0>,
+		<&qpicbam 1>,
+		<&qpicbam 2>;
+	dma-names = "tx", "rx", "cmd";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	nand@0 {
+		reg = <0>;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "boot-nand";
+				reg = <0 0x58a0000>;
+			};
+
+			partition@58a0000 {
+				label = "fs-nand";
+				reg = <0x58a0000 0x4000000>;
+			};
+		};
+	};
+};