[U-Boot,v4,6/6] apalis-tk1: fix pcie reset for reliable gigabit ethernet operation

Message ID 20170809201242.16355-7-marcel@ziswiler.com
State New
Delegated to: Tom Warren
Headers show

Commit Message

Marcel Ziswiler Aug. 9, 2017, 8:12 p.m.
From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

It turns out that the current PCIe reset implementation in the PCIe
board init function is not quite working reliably due to PCIe reset
timing violations. Fix this by overriding the
tegra_pcie_board_port_reset() function.

Also allow optionally bringing up the PCIe switch as found on the Apalis
Evaluation board. Note however that the Apalis PCIe port is also left
disabled in the device tree by default.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
---

Changes in v4: None
Changes in v3:
- Stick to struct tegra_pcie_port as suggested by Stephen.
- Introduce proper CONFIG_APALIS_TK1_PCIE_EVALBOARD_INIT Kconfig option
  as suggested by Stephen.

Changes in v2: None

 board/toradex/apalis-tk1/Kconfig      |   8 ++
 board/toradex/apalis-tk1/apalis-tk1.c | 249 +++++++++++++++++++++-------------
 2 files changed, 163 insertions(+), 94 deletions(-)

Patch

diff --git a/board/toradex/apalis-tk1/Kconfig b/board/toradex/apalis-tk1/Kconfig
index 05407ad..159b8fb 100644
--- a/board/toradex/apalis-tk1/Kconfig
+++ b/board/toradex/apalis-tk1/Kconfig
@@ -25,6 +25,14 @@  config TDX_CFG_BLOCK_PART
 config TDX_CFG_BLOCK_OFFSET
 	default "-512"
 
+config APALIS_TK1_PCIE_EVALBOARD_INIT
+	bool "Apalis Evaluation Board PCIe Initialisation"
+	help
+	  Bring up the Apalis PCIe port with the PCIe switch as found on the
+	  Apalis Evaluation board. Note that by default the PCIe port is also
+	  left disabled in the device tree which needs changing as well for this
+	  to actually work.
+
 source "board/toradex/common/Kconfig"
 
 endif
diff --git a/board/toradex/apalis-tk1/apalis-tk1.c b/board/toradex/apalis-tk1/apalis-tk1.c
index 5de61e7..ca2d61d 100644
--- a/board/toradex/apalis-tk1/apalis-tk1.c
+++ b/board/toradex/apalis-tk1/apalis-tk1.c
@@ -5,17 +5,26 @@ 
  */
 
 #include <common.h>
+#include <dm.h>
 #include <asm/arch-tegra/ap.h>
 #include <asm/gpio.h>
 #include <asm/io.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/pinmux.h>
+#include <pci_tegra.h>
 #include <power/as3722.h>
+#include <power/pmic.h>
 
 #include "../common/tdx-common.h"
 #include "pinmux-config-apalis-tk1.h"
 
-#define LAN_RESET_N TEGRA_GPIO(S, 2)
+#define LAN_DEV_OFF_N	TEGRA_GPIO(O, 6)
+#define LAN_RESET_N	TEGRA_GPIO(S, 2)
+#define LAN_WAKE_N	TEGRA_GPIO(O, 5)
+#ifdef CONFIG_APALIS_TK1_PCIE_EVALBOARD_INIT
+#define PEX_PERST_N	TEGRA_GPIO(DD, 1) /* Apalis GPIO7 */
+#define RESET_MOCI_CTRL	TEGRA_GPIO(U, 4)
+#endif /* CONFIG_APALIS_TK1_PCIE_EVALBOARD_INIT */
 
 int arch_misc_init(void)
 {
@@ -59,123 +68,175 @@  void pinmux_init(void)
 }
 
 #ifdef CONFIG_PCI_TEGRA
-int tegra_pcie_board_init(void)
+/* TODO: Convert to driver model */
+static int as3722_sd_enable(struct udevice *pmic, unsigned int sd)
 {
-	/* TODO: Convert to driver model
-	struct udevice *pmic;
 	int err;
 
-	err = as3722_init(&pmic);
+	if (sd > 6)
+		return -EINVAL;
+
+	err = pmic_clrsetbits(pmic, AS3722_SD_CONTROL, 0, 1 << sd);
 	if (err) {
-		error("failed to initialize AS3722 PMIC: %d\n", err);
+		error("failed to update SD control register: %d", err);
 		return err;
 	}
 
-	err = as3722_sd_enable(pmic, 4);
-	if (err < 0) {
-		error("failed to enable SD4: %d\n", err);
-		return err;
-	}
+	return 0;
+}
 
-	err = as3722_sd_set_voltage(pmic, 4, 0x24);
-	if (err < 0) {
-		error("failed to set SD4 voltage: %d\n", err);
-		return err;
-	}
+/* TODO: Convert to driver model */
+static int as3722_ldo_enable(struct udevice *pmic, unsigned int ldo)
+{
+	int err;
+	u8 ctrl_reg = AS3722_LDO_CONTROL0;
 
-	err = as3722_gpio_configure(pmic, 1, AS3722_GPIO_OUTPUT_VDDH |
-					     AS3722_GPIO_INVERT);
-	if (err < 0) {
-		error("failed to configure GPIO#1 as output: %d\n", err);
-		return err;
-	}
+	if (ldo > 11)
+		return -EINVAL;
 
-	err = as3722_gpio_direction_output(pmic, 2, 1);
-	if (err < 0) {
-		error("failed to set GPIO#2 high: %d\n", err);
-		return err;
+	if (ldo > 7) {
+		ctrl_reg = AS3722_LDO_CONTROL1;
+		ldo -= 8;
 	}
-	*/
 
-	/* Reset I210 Gigabit Ethernet Controller */
-	gpio_request(LAN_RESET_N, "LAN_RESET_N");
-	gpio_direction_output(LAN_RESET_N, 0);
-
-	/*
-	 * Make sure we don't get any back feeding from LAN_WAKE_N resp.
-	 * DEV_OFF_N
-	 */
-	gpio_request(TEGRA_GPIO(O, 5), "LAN_WAKE_N");
-	gpio_direction_output(TEGRA_GPIO(O, 5), 0);
-
-	gpio_request(TEGRA_GPIO(O, 6), "LAN_DEV_OFF_N");
-	gpio_direction_output(TEGRA_GPIO(O, 6), 0);
-
-	/* Make sure LDO9 and LDO10 are initially enabled @ 0V */
-	/* TODO: Convert to driver model
-	err = as3722_ldo_enable(pmic, 9);
-	if (err < 0) {
-		error("failed to enable LDO9: %d\n", err);
-		return err;
-	}
-	err = as3722_ldo_enable(pmic, 10);
-	if (err < 0) {
-		error("failed to enable LDO10: %d\n", err);
-		return err;
-	}
-	err = as3722_ldo_set_voltage(pmic, 9, 0x80);
-	if (err < 0) {
-		error("failed to set LDO9 voltage: %d\n", err);
-		return err;
-	}
-	err = as3722_ldo_set_voltage(pmic, 10, 0x80);
-	if (err < 0) {
-		error("failed to set LDO10 voltage: %d\n", err);
+	err = pmic_clrsetbits(pmic, ctrl_reg, 0, 1 << ldo);
+	if (err) {
+		error("failed to update LDO control register: %d", err);
 		return err;
 	}
-	*/
 
-	mdelay(100);
-
-	/* Make sure controller gets enabled by disabling DEV_OFF_N */
-	gpio_set_value(TEGRA_GPIO(O, 6), 1);
+	return 0;
+}
 
-	/* Enable LDO9 and LDO10 for +V3.3_ETH on patched prototypes */
-	/* TODO: Convert to driver model
-	err = as3722_ldo_set_voltage(pmic, 9, 0xff);
-	if (err < 0) {
-		error("failed to set LDO9 voltage: %d\n", err);
-		return err;
+int tegra_pcie_board_init(void)
+{
+	struct udevice *dev;
+	int ret;
+
+	ret = uclass_get_device_by_driver(UCLASS_PMIC,
+					  DM_GET_DRIVER(pmic_as3722), &dev);
+	if (ret) {
+		debug("%s: Failed to find PMIC\n", __func__);
+		return ret;
 	}
-	err = as3722_ldo_set_voltage(pmic, 10, 0xff);
-	if (err < 0) {
-		error("failed to set LDO10 voltage: %d\n", err);
-		return err;
+
+	ret = as3722_sd_enable(dev, 4);
+	if (ret < 0) {
+		error("failed to enable SD4: %d\n", ret);
+		return ret;
 	}
-	*/
 
-	mdelay(100);
-	gpio_set_value(LAN_RESET_N, 1);
+	ret = as3722_sd_set_voltage(dev, 4, 0x24);
+	if (ret < 0) {
+		error("failed to set SD4 voltage: %d\n", ret);
+		return ret;
+	}
 
-#ifdef APALIS_TK1_PCIE_EVALBOARD_INIT
-#define PEX_PERST_N	TEGRA_GPIO(DD, 1) /* Apalis GPIO7 */
-#define RESET_MOCI_CTRL	TEGRA_GPIO(U, 4)
+	gpio_request(LAN_DEV_OFF_N, "LAN_DEV_OFF_N");
+	gpio_request(LAN_RESET_N, "LAN_RESET_N");
+	gpio_request(LAN_WAKE_N, "LAN_WAKE_N");
 
-	/* Reset PLX PEX 8605 PCIe Switch plus PCIe devices on Apalis Evaluation
-	   Board */
+#ifdef CONFIG_APALIS_TK1_PCIE_EVALBOARD_INIT
 	gpio_request(PEX_PERST_N, "PEX_PERST_N");
 	gpio_request(RESET_MOCI_CTRL, "RESET_MOCI_CTRL");
-	gpio_direction_output(PEX_PERST_N, 0);
-	gpio_direction_output(RESET_MOCI_CTRL, 0);
-	/* Must be asserted for 100 ms after power and clocks are stable */
-	mdelay(100);
-	gpio_set_value(PEX_PERST_N, 1);
-	/* Err_5: PEX_REFCLK_OUTpx/nx Clock Outputs is not Guaranteed Until
-	   900 us After PEX_PERST# De-assertion */
-	mdelay(1);
-	gpio_set_value(RESET_MOCI_CTRL, 1);
-#endif /* APALIS_T30_PCIE_EVALBOARD_INIT */
+#endif /* CONFIG_APALIS_TK1_PCIE_EVALBOARD_INIT */
 
 	return 0;
 }
+
+void tegra_pcie_board_port_reset(struct tegra_pcie_port *port)
+{
+	int index = tegra_pcie_port_index_of_port(port);
+	if (index == 1) { /* I210 Gigabit Ethernet Controller (On-module) */
+		struct udevice *dev;
+		int ret;
+
+		ret = uclass_get_device_by_driver(UCLASS_PMIC,
+						  DM_GET_DRIVER(pmic_as3722),
+						  &dev);
+		if (ret) {
+			debug("%s: Failed to find PMIC\n", __func__);
+			return;
+		}
+
+		/* Reset I210 Gigabit Ethernet Controller */
+		gpio_direction_output(LAN_RESET_N, 0);
+
+		/*
+		 * Make sure we don't get any back feeding from DEV_OFF_N resp.
+		 * LAN_WAKE_N
+		 */
+		gpio_direction_output(LAN_DEV_OFF_N, 0);
+		gpio_direction_output(LAN_WAKE_N, 0);
+
+		/* Make sure LDO9 and LDO10 are initially enabled @ 0V */
+		ret = as3722_ldo_enable(dev, 9);
+		if (ret < 0) {
+			error("failed to enable LDO9: %d\n", ret);
+			return;
+		}
+		ret = as3722_ldo_enable(dev, 10);
+		if (ret < 0) {
+			error("failed to enable LDO10: %d\n", ret);
+			return;
+		}
+		ret = as3722_ldo_set_voltage(dev, 9, 0x80);
+		if (ret < 0) {
+			error("failed to set LDO9 voltage: %d\n", ret);
+			return;
+		}
+		ret = as3722_ldo_set_voltage(dev, 10, 0x80);
+		if (ret < 0) {
+			error("failed to set LDO10 voltage: %d\n", ret);
+			return;
+		}
+
+		/* Make sure controller gets enabled by disabling DEV_OFF_N */
+		gpio_set_value(LAN_DEV_OFF_N, 1);
+
+		/*
+		 * Enable LDO9 and LDO10 for +V3.3_ETH on patched prototype
+		 * V1.0A and sample V1.0B and newer modules
+		 */
+		ret = as3722_ldo_set_voltage(dev, 9, 0xff);
+		if (ret < 0) {
+			error("failed to set LDO9 voltage: %d\n", ret);
+			return;
+		}
+		ret = as3722_ldo_set_voltage(dev, 10, 0xff);
+		if (ret < 0) {
+			error("failed to set LDO10 voltage: %d\n", ret);
+			return;
+		}
+
+		/*
+		 * Must be asserted for 100 ms after power and clocks are stable
+		 */
+		mdelay(100);
+
+		gpio_set_value(LAN_RESET_N, 1);
+	} else if (index == 0) { /* Apalis PCIe */
+#ifdef CONFIG_APALIS_TK1_PCIE_EVALBOARD_INIT
+		/*
+		 * Reset PLX PEX 8605 PCIe Switch plus PCIe devices on Apalis
+		 * Evaluation Board
+		 */
+		gpio_direction_output(PEX_PERST_N, 0);
+		gpio_direction_output(RESET_MOCI_CTRL, 0);
+
+		/*
+		 * Must be asserted for 100 ms after power and clocks are stable
+		 */
+		mdelay(100);
+
+		gpio_set_value(PEX_PERST_N, 1);
+		/*
+		 * Err_5: PEX_REFCLK_OUTpx/nx Clock Outputs is not Guaranteed
+		 * Until 900 us After PEX_PERST# De-assertion
+		 */
+		mdelay(1);
+		gpio_set_value(RESET_MOCI_CTRL, 1);
+#endif /* CONFIG_APALIS_TK1_PCIE_EVALBOARD_INIT */
+	}
+}
 #endif /* CONFIG_PCI_TEGRA */