| Message ID | 20170613231035.494020-7-salil.mehta@huawei.com |
|---|---|
| State | Changes Requested, archived |
| Delegated to: | David Miller |
| Headers | show |
On 06/13/2017 04:10 PM, Salil Mehta wrote: > This patch adds the support of MDIO bus interface for HNS3 driver. > Code provides various interfaces to start and stop the PHY layer > and to read and write the MDIO bus or PHY. > > Signed-off-by: Daode Huang <huangdaode@hisilicon.com> > Signed-off-by: lipeng <lipeng321@huawei.com> > Signed-off-by: Salil Mehta <salil.mehta@huawei.com> > Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com> > --- > + phy = get_phy_device(mdio_bus, mac->phy_addr, mac->is_c45); > + if (!phy || IS_ERR(phy)) { > + dev_err(mdio_bus->parent, "Failed to get phy device\n"); > + ret = -EIO; > + goto err_mdio_register; > + } > + > + phy->irq = mdio_bus->irq[mac->phy_addr]; > + > + /* All data is now stored in the phy struct; > + * register it > + */ > + ret = phy_device_register(phy); > + if (ret) { > + ret = -ENODEV; > + goto err_phy_register; > + } Until this gets fixed in the core PHY library, it's okay to do that, but please fix the > + > + mac->phy_dev = phy; > + > + return 0; > + > +err_phy_register: > + phy_device_free(phy); > + > +err_mdio_register: > + mdiobus_unregister(mdio_bus); > + mdiobus_free(mdio_bus); > +err_miibus_alloc: > + return ret; > +} > + > +static void hclge_mac_adjust_link(struct net_device *net_dev) > +{ > + int duplex; > + int speed; > + struct hclge_mac *hw_mac; > + struct hclge_hw *hw; > + struct hclge_dev *hdev; > + > + if (!net_dev) > + return; > + > + hw_mac = container_of(net_dev, struct hclge_mac, ndev); > + hw = container_of(hw_mac, struct hclge_hw, mac); > + hdev = hw->back; > + > + speed = hw_mac->phy_dev->speed; > + duplex = hw_mac->phy_dev->duplex; > + > + /* update antoneg. */ > + hw_mac->autoneg = hw_mac->phy_dev->autoneg; > + > + if ((hw_mac->speed != speed) || (hw_mac->duplex != duplex)) > + (void)hclge_cfg_mac_speed_dup(hdev, speed, !!duplex); > +} > + > +int hclge_mac_start_phy(struct hclge_dev *hdev) > +{ > + struct hclge_mac *mac = &hdev->hw.mac; > + struct phy_device *phy_dev = mac->phy_dev; > + int ret; > + > + if (!phy_dev) > + return 0; > + > + if (mac->phy_if != PHY_INTERFACE_MODE_XGMII) { > + phy_dev->dev_flags = 0; > + > + ret = phy_connect_direct(&mac->ndev, phy_dev, > + hclge_mac_adjust_link, > + mac->phy_if); > + phy_dev->supported = SUPPORTED_10baseT_Half | > + SUPPORTED_10baseT_Full | > + SUPPORTED_100baseT_Half | > + SUPPORTED_100baseT_Full | > + SUPPORTED_Autoneg | > + SUPPORTED_1000baseT_Full; > + > + phy_dev->autoneg = false; > + } else { > + ret = phy_attach_direct(&mac->ndev, phy_dev, 0, mac->phy_if); > + phy_dev->supported = SUPPORTED_10000baseR_FEC | > + SUPPORTED_10000baseKR_Full; > + } I really don't see why you don't take the exact same path whether it's XGMII or not, just like you are not masking with that the PHY driver already supports, this needs fixing. > + if (unlikely(ret)) > + return -ENODEV; > + > + phy_start(phy_dev); > + > + return 0; > +} > + > +void hclge_mac_stop_phy(struct hclge_dev *hdev) > +{ > + struct hclge_mac *mac = &hdev->hw.mac; > + struct phy_device *phy_dev = mac->phy_dev; > + > + if (!phy_dev) > + return; > + > + phy_stop(phy_dev); > + > + if (mac->phy_if != PHY_INTERFACE_MODE_XGMII) > + phy_disconnect(phy_dev); > + else > + phy_detach(phy_dev); Same here.
> +struct hclge_mdio_cfg_cmd { > + u8 ctrl_bit; > + u8 prtad; /* The external port address */ > + u8 devad; /* The external device address */ > + u8 rsvd; > + __le16 addr_c45;/* Only valid for c45 */ > + __le16 data_wr; > + __le16 data_rd; > + __le16 sta; > +}; > + > +static int hclge_mdio_write(struct mii_bus *bus, int phy_id, int regnum, > + u16 data) > +{ > + struct hclge_dev *hdev = (struct hclge_dev *)bus->priv; > + struct hclge_mdio_cfg_cmd *mdio_cmd; > + enum hclge_cmd_status status; > + struct hclge_desc desc; > + u8 is_c45, devad; > + u16 reg; > + > + if (!bus) > + return -EINVAL; > + > + is_c45 = !!(regnum & MII_ADDR_C45); > + devad = ((regnum >> 16) & 0x1f); > + reg = (u16)(regnum & 0xffff); > + > + hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_MDIO_CONFIG, false); > + > + mdio_cmd = (struct hclge_mdio_cfg_cmd *)desc.data; > + > + mdio_cmd->ctrl_bit |= HCLGE_MDIO_CTRL_START_BIT; > + mdio_cmd->prtad = phy_id & HCLGE_MDIO_CTRL_PRTAD_MSK; > + mdio_cmd->data_wr = cpu_to_le16(data); > + mdio_cmd->devad = devad & HCLGE_MDIO_CTRL_DEVAD_MSK; > + > + if (is_c45) { > + /* Set phy addr */ > + mdio_cmd->addr_c45 = cpu_to_le16(reg); > + } else { > + /* C22 write reg and data */ > + mdio_cmd->ctrl_bit = HCLGE_MDIO_IS_C22(!is_c45); > + mdio_cmd->ctrl_bit |= HCLGE_MDIO_CTRL_OP(HCLGE_MDIO_C22_WRITE); > + } When doing C22, i don't see you putting the reg into mdio_cmd anywhere? Also mdio_cmd->ctrl_bit = HCLGE_MDIO_IS_C22(!is_c45); can be pulled of the if/then/else since it takes is_c45 as a parameter, or simplified. Andrew
> + if (le16_to_cpu(HCLGE_MDIO_STA_VAL(mdio_cmd->sta))) { > + dev_err(&hdev->pdev->dev, "mdio read data error\n"); > + return -ENOMEM; > + } If it is not zero, it is an error. !0 is always !0, big or little endian, so there is no point doing the le16_to_cpu(). Where is the memory allocation which failed? Andrew
Hi Florian > -----Original Message----- > From: Florian Fainelli [mailto:f.fainelli@gmail.com] > Sent: Wednesday, June 14, 2017 12:46 AM > To: Salil Mehta; davem@davemloft.net > Cc: Zhuangyuzeng (Yisen); huangdaode; lipeng (Y); > mehta.salil.lnk@gmail.com; netdev@vger.kernel.org; linux- > kernel@vger.kernel.org; Linuxarm > Subject: Re: [PATCH V2 net-next 6/8] net: hns3: Add MDIO support to > HNS3 Ethernet driver for hip08 SoC > > On 06/13/2017 04:10 PM, Salil Mehta wrote: > > This patch adds the support of MDIO bus interface for HNS3 driver. > > Code provides various interfaces to start and stop the PHY layer > > and to read and write the MDIO bus or PHY. > > > > Signed-off-by: Daode Huang <huangdaode@hisilicon.com> > > Signed-off-by: lipeng <lipeng321@huawei.com> > > Signed-off-by: Salil Mehta <salil.mehta@huawei.com> > > Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com> > > --- > > > + phy = get_phy_device(mdio_bus, mac->phy_addr, mac->is_c45); > > + if (!phy || IS_ERR(phy)) { > > + dev_err(mdio_bus->parent, "Failed to get phy device\n"); > > + ret = -EIO; > > + goto err_mdio_register; > > + } > > + > > + phy->irq = mdio_bus->irq[mac->phy_addr]; > > + > > + /* All data is now stored in the phy struct; > > + * register it > > + */ > > + ret = phy_device_register(phy); > > + if (ret) { > > + ret = -ENODEV; > > + goto err_phy_register; > > + } > > Until this gets fixed in the core PHY library, it's okay to do that, > but > please fix the For now we are planning to drop the support of C45 till we fix this issue in the core. I Will try to address this as a separate patch. Thanks Salil > > > + > > + mac->phy_dev = phy; > > + > > + return 0; > > + > > +err_phy_register: > > + phy_device_free(phy); > > + > > +err_mdio_register: > > + mdiobus_unregister(mdio_bus); > > + mdiobus_free(mdio_bus); > > +err_miibus_alloc: > > + return ret; > > +} > > + > > +static void hclge_mac_adjust_link(struct net_device *net_dev) > > +{ > > + int duplex; > > + int speed; > > + struct hclge_mac *hw_mac; > > + struct hclge_hw *hw; > > + struct hclge_dev *hdev; > > + > > + if (!net_dev) > > + return; > > + > > + hw_mac = container_of(net_dev, struct hclge_mac, ndev); > > + hw = container_of(hw_mac, struct hclge_hw, mac); > > + hdev = hw->back; > > + > > + speed = hw_mac->phy_dev->speed; > > + duplex = hw_mac->phy_dev->duplex; > > + > > + /* update antoneg. */ > > + hw_mac->autoneg = hw_mac->phy_dev->autoneg; > > + > > + if ((hw_mac->speed != speed) || (hw_mac->duplex != duplex)) > > + (void)hclge_cfg_mac_speed_dup(hdev, speed, !!duplex); > > +} > > + > > +int hclge_mac_start_phy(struct hclge_dev *hdev) > > +{ > > + struct hclge_mac *mac = &hdev->hw.mac; > > + struct phy_device *phy_dev = mac->phy_dev; > > + int ret; > > + > > + if (!phy_dev) > > + return 0; > > + > > + if (mac->phy_if != PHY_INTERFACE_MODE_XGMII) { > > + phy_dev->dev_flags = 0; > > + > > + ret = phy_connect_direct(&mac->ndev, phy_dev, > > + hclge_mac_adjust_link, > > + mac->phy_if); > > + phy_dev->supported = SUPPORTED_10baseT_Half | > > + SUPPORTED_10baseT_Full | > > + SUPPORTED_100baseT_Half | > > + SUPPORTED_100baseT_Full | > > + SUPPORTED_Autoneg | > > + SUPPORTED_1000baseT_Full; > > + > > + phy_dev->autoneg = false; > > + } else { > > + ret = phy_attach_direct(&mac->ndev, phy_dev, 0, mac- > >phy_if); > > + phy_dev->supported = SUPPORTED_10000baseR_FEC | > > + SUPPORTED_10000baseKR_Full; > > + } > > I really don't see why you don't take the exact same path whether it's > XGMII or not, just like you are not masking with that the PHY driver > already supports, this needs fixing. Sure will fix it in next V3 patch. Thanks Salil > > > + if (unlikely(ret)) > > + return -ENODEV; > > + > > + phy_start(phy_dev); > > + > > + return 0; > > +} > > + > > +void hclge_mac_stop_phy(struct hclge_dev *hdev) > > +{ > > + struct hclge_mac *mac = &hdev->hw.mac; > > + struct phy_device *phy_dev = mac->phy_dev; > > + > > + if (!phy_dev) > > + return; > > + > > + phy_stop(phy_dev); > > + > > + if (mac->phy_if != PHY_INTERFACE_MODE_XGMII) > > + phy_disconnect(phy_dev); > > + else > > + phy_detach(phy_dev); > > Same here. Will fix it in next V3 patch. Thanks Salil > -- > Florian
Hi Andrew, > -----Original Message----- > From: Andrew Lunn [mailto:andrew@lunn.ch] > Sent: Wednesday, June 14, 2017 3:43 AM > To: Salil Mehta > Cc: davem@davemloft.net; Zhuangyuzeng (Yisen); huangdaode; lipeng (Y); > mehta.salil.lnk@gmail.com; netdev@vger.kernel.org; linux- > kernel@vger.kernel.org; Linuxarm > Subject: Re: [PATCH V2 net-next 6/8] net: hns3: Add MDIO support to > HNS3 Ethernet driver for hip08 SoC > > > +struct hclge_mdio_cfg_cmd { > > + u8 ctrl_bit; > > + u8 prtad; /* The external port address */ > > + u8 devad; /* The external device address */ > > + u8 rsvd; > > + __le16 addr_c45;/* Only valid for c45 */ > > + __le16 data_wr; > > + __le16 data_rd; > > + __le16 sta; > > +}; > > + > > +static int hclge_mdio_write(struct mii_bus *bus, int phy_id, int > regnum, > > + u16 data) > > +{ > > + struct hclge_dev *hdev = (struct hclge_dev *)bus->priv; > > + struct hclge_mdio_cfg_cmd *mdio_cmd; > > + enum hclge_cmd_status status; > > + struct hclge_desc desc; > > + u8 is_c45, devad; > > + u16 reg; > > + > > + if (!bus) > > + return -EINVAL; > > + > > + is_c45 = !!(regnum & MII_ADDR_C45); > > + devad = ((regnum >> 16) & 0x1f); > > + reg = (u16)(regnum & 0xffff); > > + > > + hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_MDIO_CONFIG, false); > > + > > + mdio_cmd = (struct hclge_mdio_cfg_cmd *)desc.data; > > + > > + mdio_cmd->ctrl_bit |= HCLGE_MDIO_CTRL_START_BIT; > > + mdio_cmd->prtad = phy_id & HCLGE_MDIO_CTRL_PRTAD_MSK; > > + mdio_cmd->data_wr = cpu_to_le16(data); > > + mdio_cmd->devad = devad & HCLGE_MDIO_CTRL_DEVAD_MSK; > > + > > + if (is_c45) { > > + /* Set phy addr */ > > + mdio_cmd->addr_c45 = cpu_to_le16(reg); > > + } else { > > + /* C22 write reg and data */ > > + mdio_cmd->ctrl_bit = HCLGE_MDIO_IS_C22(!is_c45); > > + mdio_cmd->ctrl_bit |= > HCLGE_MDIO_CTRL_OP(HCLGE_MDIO_C22_WRITE); > > + } > > When doing C22, i don't see you putting the reg into mdio_cmd anywhere? > You are right. Will remove. Thanks Salil > Also > > mdio_cmd->ctrl_bit = HCLGE_MDIO_IS_C22(!is_c45); > > can be pulled of the if/then/else since it takes is_c45 as a > parameter, or simplified. > > Andrew Sure, thanks will do. Salil
Hi Andrew, > -----Original Message----- > From: Andrew Lunn [mailto:andrew@lunn.ch] > Sent: Wednesday, June 14, 2017 3:56 AM > To: Salil Mehta > Cc: davem@davemloft.net; Zhuangyuzeng (Yisen); huangdaode; lipeng (Y); > mehta.salil.lnk@gmail.com; netdev@vger.kernel.org; linux- > kernel@vger.kernel.org; Linuxarm > Subject: Re: [PATCH V2 net-next 6/8] net: hns3: Add MDIO support to > HNS3 Ethernet driver for hip08 SoC > > > + if (le16_to_cpu(HCLGE_MDIO_STA_VAL(mdio_cmd->sta))) { > > + dev_err(&hdev->pdev->dev, "mdio read data error\n"); > > + return -ENOMEM; > > + } > > If it is not zero, it is an error. !0 is always !0, big or little > endian, so there is no point doing the le16_to_cpu(). > > Where is the memory allocation which failed? > > Andrew Agreed! Will remove this. Thanks Salil
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c new file mode 100644 index 0000000..4d3a32b --- /dev/null +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c @@ -0,0 +1,295 @@ +/* + * Copyright (c) 2016~2017 Hisilicon Limited. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/etherdevice.h> +#include <linux/kernel.h> + +#include "hclge_cmd.h" +#include "hclge_main.h" + +enum hclge_mdio_c22_op_seq { + HCLGE_MDIO_C22_WRITE = 1, + HCLGE_MDIO_C22_READ = 2 +}; + +enum hclge_mdio_c45_op_seq { + HCLGE_MDIO_C45_WRITE_ADDR = 0, + HCLGE_MDIO_C45_WRITE_DATA, + HCLGE_MDIO_C45_READ_INCREMENT, + HCLGE_MDIO_C45_READ +}; + +#define HCLGE_MDIO_CTRL_START_BIT BIT(0) +#define HCLGE_MDIO_CTRL_ST_MSK GENMASK(2, 1) +#define HCLGE_MDIO_CTRL_ST_LSH 1 +#define HCLGE_MDIO_IS_C22(c22) (((c22) << HCLGE_MDIO_CTRL_ST_LSH) & \ + HCLGE_MDIO_CTRL_ST_MSK) + +#define HCLGE_MDIO_CTRL_OP_MSK GENMASK(4, 3) +#define HCLGE_MDIO_CTRL_OP_LSH 3 +#define HCLGE_MDIO_CTRL_OP(access) \ + (((access) << HCLGE_MDIO_CTRL_OP_LSH) & HCLGE_MDIO_CTRL_OP_MSK) +#define HCLGE_MDIO_CTRL_PRTAD_MSK GENMASK(4, 0) +#define HCLGE_MDIO_CTRL_DEVAD_MSK GENMASK(4, 0) + +#define HCLGE_MDIO_STA_VAL(val) ((val) & BIT(0)) + +struct hclge_mdio_cfg_cmd { + u8 ctrl_bit; + u8 prtad; /* The external port address */ + u8 devad; /* The external device address */ + u8 rsvd; + __le16 addr_c45;/* Only valid for c45 */ + __le16 data_wr; + __le16 data_rd; + __le16 sta; +}; + +static int hclge_mdio_write(struct mii_bus *bus, int phy_id, int regnum, + u16 data) +{ + struct hclge_dev *hdev = (struct hclge_dev *)bus->priv; + struct hclge_mdio_cfg_cmd *mdio_cmd; + enum hclge_cmd_status status; + struct hclge_desc desc; + u8 is_c45, devad; + u16 reg; + + if (!bus) + return -EINVAL; + + is_c45 = !!(regnum & MII_ADDR_C45); + devad = ((regnum >> 16) & 0x1f); + reg = (u16)(regnum & 0xffff); + + hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_MDIO_CONFIG, false); + + mdio_cmd = (struct hclge_mdio_cfg_cmd *)desc.data; + + mdio_cmd->ctrl_bit |= HCLGE_MDIO_CTRL_START_BIT; + mdio_cmd->prtad = phy_id & HCLGE_MDIO_CTRL_PRTAD_MSK; + mdio_cmd->data_wr = cpu_to_le16(data); + mdio_cmd->devad = devad & HCLGE_MDIO_CTRL_DEVAD_MSK; + + if (is_c45) { + /* Set phy addr */ + mdio_cmd->addr_c45 = cpu_to_le16(reg); + } else { + /* C22 write reg and data */ + mdio_cmd->ctrl_bit = HCLGE_MDIO_IS_C22(!is_c45); + mdio_cmd->ctrl_bit |= HCLGE_MDIO_CTRL_OP(HCLGE_MDIO_C22_WRITE); + } + + status = hclge_cmd_send(&hdev->hw, &desc, 1); + if (status) { + dev_err(&hdev->pdev->dev, + "mdio write fail when sending cmd, status is %d.\n", + status); + return -EIO; + } + + return 0; +} + +static int hclge_mdio_read(struct mii_bus *bus, int phy_id, int regnum) +{ + struct hclge_dev *hdev = (struct hclge_dev *)bus->priv; + struct hclge_mdio_cfg_cmd *mdio_cmd; + enum hclge_cmd_status status; + struct hclge_desc desc; + u8 is_c45, devad; + u16 reg; + + if (!bus) + return -EINVAL; + + is_c45 = !!(regnum & MII_ADDR_C45); + devad = ((regnum >> 16) & GENMASK(4, 0)); + reg = (u16)(regnum & GENMASK(15, 0)); + + hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_MDIO_CONFIG, true); + + mdio_cmd = (struct hclge_mdio_cfg_cmd *)desc.data; + + dev_dbg(&bus->dev, "phy id=%d, is_c45=%d, devad=%d, reg=%#x!\n", + phy_id, is_c45, devad, reg); + + mdio_cmd->ctrl_bit |= HCLGE_MDIO_CTRL_START_BIT; + mdio_cmd->prtad = phy_id & HCLGE_MDIO_CTRL_PRTAD_MSK; + mdio_cmd->devad = devad & HCLGE_MDIO_CTRL_DEVAD_MSK; + + if (is_c45) { + /* C45 phy addr */ + mdio_cmd->addr_c45 = cpu_to_le16(reg); + } else { + /* C22 read reg */ + mdio_cmd->ctrl_bit = HCLGE_MDIO_IS_C22(!is_c45); + mdio_cmd->ctrl_bit |= HCLGE_MDIO_CTRL_OP(HCLGE_MDIO_C22_READ); + } + + /* Read out phy data */ + status = hclge_cmd_send(&hdev->hw, &desc, 1); + if (status) { + dev_err(&hdev->pdev->dev, + "mdio read fail when get data, status is %d.\n", + status); + return -EIO; + } + + if (le16_to_cpu(HCLGE_MDIO_STA_VAL(mdio_cmd->sta))) { + dev_err(&hdev->pdev->dev, "mdio read data error\n"); + return -ENOMEM; + } + + return le16_to_cpu(mdio_cmd->data_rd); +} + +int hclge_mac_mdio_config(struct hclge_dev *hdev) +{ + struct hclge_mac *mac = &hdev->hw.mac; + struct mii_bus *mdio_bus; + struct net_device *ndev = &mac->ndev; + struct phy_device *phy; + int ret; + + if (hdev->hw.mac.phy_addr >= PHY_MAX_ADDR) + return 0; + + SET_NETDEV_DEV(ndev, &hdev->pdev->dev); + + mdio_bus = devm_mdiobus_alloc(&hdev->pdev->dev); + if (!mdio_bus) { + ret = -ENOMEM; + goto err_miibus_alloc; + } + + mdio_bus->name = "hisilicon MII bus"; + mdio_bus->read = hclge_mdio_read; + mdio_bus->write = hclge_mdio_write; + snprintf(mdio_bus->id, MII_BUS_ID_SIZE, "%s-%s", "mii", + dev_name(&hdev->pdev->dev)); + + mdio_bus->parent = &hdev->pdev->dev; + mdio_bus->priv = hdev; + mdio_bus->phy_mask = ~(1 << mac->phy_addr); + ret = mdiobus_register(mdio_bus); + if (ret) { + dev_err(mdio_bus->parent, + "Failed to register MDIO bus ret = %#x\n", ret); + goto err_mdio_register; + } + + phy = get_phy_device(mdio_bus, mac->phy_addr, mac->is_c45); + if (!phy || IS_ERR(phy)) { + dev_err(mdio_bus->parent, "Failed to get phy device\n"); + ret = -EIO; + goto err_mdio_register; + } + + phy->irq = mdio_bus->irq[mac->phy_addr]; + + /* All data is now stored in the phy struct; + * register it + */ + ret = phy_device_register(phy); + if (ret) { + ret = -ENODEV; + goto err_phy_register; + } + + mac->phy_dev = phy; + + return 0; + +err_phy_register: + phy_device_free(phy); + +err_mdio_register: + mdiobus_unregister(mdio_bus); + mdiobus_free(mdio_bus); +err_miibus_alloc: + return ret; +} + +static void hclge_mac_adjust_link(struct net_device *net_dev) +{ + int duplex; + int speed; + struct hclge_mac *hw_mac; + struct hclge_hw *hw; + struct hclge_dev *hdev; + + if (!net_dev) + return; + + hw_mac = container_of(net_dev, struct hclge_mac, ndev); + hw = container_of(hw_mac, struct hclge_hw, mac); + hdev = hw->back; + + speed = hw_mac->phy_dev->speed; + duplex = hw_mac->phy_dev->duplex; + + /* update antoneg. */ + hw_mac->autoneg = hw_mac->phy_dev->autoneg; + + if ((hw_mac->speed != speed) || (hw_mac->duplex != duplex)) + (void)hclge_cfg_mac_speed_dup(hdev, speed, !!duplex); +} + +int hclge_mac_start_phy(struct hclge_dev *hdev) +{ + struct hclge_mac *mac = &hdev->hw.mac; + struct phy_device *phy_dev = mac->phy_dev; + int ret; + + if (!phy_dev) + return 0; + + if (mac->phy_if != PHY_INTERFACE_MODE_XGMII) { + phy_dev->dev_flags = 0; + + ret = phy_connect_direct(&mac->ndev, phy_dev, + hclge_mac_adjust_link, + mac->phy_if); + phy_dev->supported = SUPPORTED_10baseT_Half | + SUPPORTED_10baseT_Full | + SUPPORTED_100baseT_Half | + SUPPORTED_100baseT_Full | + SUPPORTED_Autoneg | + SUPPORTED_1000baseT_Full; + + phy_dev->autoneg = false; + } else { + ret = phy_attach_direct(&mac->ndev, phy_dev, 0, mac->phy_if); + phy_dev->supported = SUPPORTED_10000baseR_FEC | + SUPPORTED_10000baseKR_Full; + } + if (unlikely(ret)) + return -ENODEV; + + phy_start(phy_dev); + + return 0; +} + +void hclge_mac_stop_phy(struct hclge_dev *hdev) +{ + struct hclge_mac *mac = &hdev->hw.mac; + struct phy_device *phy_dev = mac->phy_dev; + + if (!phy_dev) + return; + + phy_stop(phy_dev); + + if (mac->phy_if != PHY_INTERFACE_MODE_XGMII) + phy_disconnect(phy_dev); + else + phy_detach(phy_dev); +}