@@ -171,6 +171,7 @@ static uint64_t aspeed_i2c_bus_read(void *opaque, hwaddr offset,
static void aspeed_i2c_bus_handle_cmd(AspeedI2CBus *bus, uint64_t value)
{
+ bus->cmd &= ~0xFFFF;
bus->cmd |= value & 0xFFFF;
bus->intr_status = 0;
@@ -182,15 +183,27 @@ static void aspeed_i2c_bus_handle_cmd(AspeedI2CBus *bus, uint64_t value)
bus->intr_status |= I2CD_INTR_TX_ACK;
}
- } else if (bus->cmd & I2CD_M_TX_CMD) {
+ /* START command is also a TX command, as the slave address is
+ * sent on the bus */
+ bus->cmd &= ~(I2CD_M_START_CMD | I2CD_M_TX_CMD);
+
+ /* No slave found */
+ if (!i2c_bus_busy(bus->bus)) {
+ return;
+ }
+ }
+
+ if (bus->cmd & I2CD_M_TX_CMD) {
if (i2c_send(bus->bus, bus->buf)) {
bus->intr_status |= (I2CD_INTR_TX_NAK | I2CD_INTR_ABNORMAL);
i2c_end_transfer(bus->bus);
} else {
bus->intr_status |= I2CD_INTR_TX_ACK;
}
+ bus->cmd &= ~I2CD_M_TX_CMD;
+ }
- } else if (bus->cmd & I2CD_M_RX_CMD) {
+ if (bus->cmd & I2CD_M_RX_CMD) {
int ret = i2c_recv(bus->bus);
if (ret < 0) {
qemu_log_mask(LOG_GUEST_ERROR, "%s: read failed\n", __func__);
@@ -199,6 +212,7 @@ static void aspeed_i2c_bus_handle_cmd(AspeedI2CBus *bus, uint64_t value)
bus->intr_status |= I2CD_INTR_RX_DONE;
}
bus->buf = (ret & I2CD_BYTE_BUF_RX_MASK) << I2CD_BYTE_BUF_RX_SHIFT;
+ bus->cmd &= ~I2CD_M_RX_CMD;
}
if (bus->cmd & (I2CD_M_STOP_CMD | I2CD_M_S_RX_CMD_LAST)) {
@@ -208,11 +222,8 @@ static void aspeed_i2c_bus_handle_cmd(AspeedI2CBus *bus, uint64_t value)
i2c_end_transfer(bus->bus);
bus->intr_status |= I2CD_INTR_NORMAL_STOP;
}
+ bus->cmd &= ~I2CD_M_STOP_CMD;
}
-
- /* command is handled, reset it and check for interrupts */
- bus->cmd &= ~0xFFFF;
- aspeed_i2c_bus_raise_interrupt(bus);
}
static void aspeed_i2c_bus_write(void *opaque, hwaddr offset,
@@ -262,6 +273,7 @@ static void aspeed_i2c_bus_write(void *opaque, hwaddr offset,
}
aspeed_i2c_bus_handle_cmd(bus, value);
+ aspeed_i2c_bus_raise_interrupt(bus);
break;
default:
Multiple I2C commands can be fired simultaneously and the controller execute the commands following these priorities: (1) Master Start Command (2) Master Transmit Command (3) Slave Transmit Command or Master Receive Command (4) Master Stop Command The current code is incorrect with respect to the above sequence and needs to be reworked to handle each individual command. Signed-off-by: Cédric Le Goater <clg@kaod.org> --- hw/i2c/aspeed_i2c.c | 24 ++++++++++++++++++------ 1 file changed, 18 insertions(+), 6 deletions(-)