| Message ID | 1605874.IPVSbxyx3P@c21 |
|---|---|
| State | Not Applicable |
| Delegated to: | David Miller |
| Headers | show |
Hello, On Sat, Apr 22, 2017 at 05:33:56PM +0200, mtths@nurfuerspam.de wrote: > A SATA PCI-controller card using the kernel module sata_sil24 has problems > transferring big files. > > > First of all a description of the situation: > > -- Hardware: > - mainboard Gigabyte GA-MA69GM-S2H; chipset AMD 690G / SB600; 2 PCI slots > (32 bit); 1 PCIe 4x slot; 1 PCIe 16 x slot; 8 GiB RAM; AMD Phenom(tm) II X4 > 955 Processor > - SATA controller card Dawicontrol DC-3410 RAID, 32 bit PCI; chipset > SiI3124ACBHU; BIOS message: running at 32 bit / 33 MHz > - with hard disks: HDS721616PLA380 (twice), ST3000DM001-9YN166 (temporary) > - q.v. attachment lspci; (dmidecode (v 3.0) finds no SMBIOS nor DMI entry > point) ... > 1st test setting: > Reading from the disks to /dev/null with > dd if=/dev/sde of=/dev/null bs=4k count=2304k > one after the other. (Disk ST3000DM001 was temporarily directly connected to > the card's external SATA port.) > Result: After some MB, but before 470 MiB errors occurred: > failed command: READ FPDMA QUEUED > [cf. attachment dmesg] > failed command: READ DMA > [cf. attachment dmesg_tmpHD] > The errors were reproducible - however, they started after different amounts > of data. > > 2nd test setting: > Using Debian's kernel and patching the driver to not use 64 bit DMA [cf. > attachment sata_sil24.c.diff]. > Doing the same tests as above. > Result: Repeatedly no errors occurred. > > > N.B.: 1) There is a Windows Vista (32 bit) installation that uses two of the > ports of the controller card as a fake RAID 1: There are no problems with the > internal directly connected drives nor with an external drive. > 2) Prior to this controller card there was a PCI Express card using SiI 3132, > that - if I remember rightly - also had such problems, but they started after > a greater amount of data. (At that time a Windows XP x64 installation had no > problems, too.) That's interesting, so you're seeing similar host bus errors whether the controller is attached to PCI or PCIe. The controller itself is known to be okay with 64bit addressing and restricting it to 32bit addressing means that you'd be bouncing pages (DMA to low pages and then copy using CPU), which slows down things a bit. It could be that the slowing down in timing is what's helping, not necessarily forcing 32bit DMA. I don't know. Host bus errors are rarely reported and the controller is definitely known to be okay with 64bit DMAs. Given this didn't get reported at all in the haydays of SB600, it could actually be faulty hardware. I'm not sure what we can do at the moment. Thanks.
--- drivers/ata/sata_sil24.c.orig 2017-01-09 08:32:38.000000000 +0100 +++ drivers/ata/sata_sil24.c 2017-01-13 23:44:58.378675018 +0100 @@ -1313,15 +1313,4 @@ /* configure and activate the device */ - if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) { - rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64)); - if (rc) { - rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32)); - if (rc) { - dev_err(&pdev->dev, - "64-bit DMA enable failed\n"); - return rc; - } - } - } else { rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)); if (rc) { @@ -1335,5 +1324,4 @@ return rc; } - } /* Set max read request size to 4096. This slightly increases
A SATA PCI-controller card using the kernel module sata_sil24 has problems transferring big files. First of all a description of the situation: -- Hardware: - mainboard Gigabyte GA-MA69GM-S2H; chipset AMD 690G / SB600; 2 PCI slots (32 bit); 1 PCIe 4x slot; 1 PCIe 16 x slot; 8 GiB RAM; AMD Phenom(tm) II X4 955 Processor - SATA controller card Dawicontrol DC-3410 RAID, 32 bit PCI; chipset SiI3124ACBHU; BIOS message: running at 32 bit / 33 MHz - with hard disks: HDS721616PLA380 (twice), ST3000DM001-9YN166 (temporary) - q.v. attachment lspci; (dmidecode (v 3.0) finds no SMBIOS nor DMI entry point) -- [Debian] System Information: Debian Release: stretch/sid APT prefers unstable APT policy: (998, 'unstable') Architecture: amd64 (x86_64) Kernel: Linux 4.9.2 (SMP w/4 CPU cores) Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) Versions of packages linux-source-4.9 depends on: ii binutils 2.27.90.20170113-1 ii xz-utils 5.2.2-1.2 Versions of packages linux-source-4.9 recommends: ii bc 1.06.95-9+b2 ii gcc 4:6.2.1-1 ii libc6-dev [libc-dev] 2.24-8 ii make 4.1-9 Versions of packages linux-source-4.9 suggests: ii libncurses5-dev [ncurses-dev] 6.0+20161126-1 pn libqt4-dev <none> pn pkg-config <none> 1st test setting: Reading from the disks to /dev/null with dd if=/dev/sde of=/dev/null bs=4k count=2304k one after the other. (Disk ST3000DM001 was temporarily directly connected to the card's external SATA port.) Result: After some MB, but before 470 MiB errors occurred: failed command: READ FPDMA QUEUED [cf. attachment dmesg] failed command: READ DMA [cf. attachment dmesg_tmpHD] The errors were reproducible - however, they started after different amounts of data. 2nd test setting: Using Debian's kernel and patching the driver to not use 64 bit DMA [cf. attachment sata_sil24.c.diff]. Doing the same tests as above. Result: Repeatedly no errors occurred. N.B.: 1) There is a Windows Vista (32 bit) installation that uses two of the ports of the controller card as a fake RAID 1: There are no problems with the internal directly connected drives nor with an external drive. 2) Prior to this controller card there was a PCI Express card using SiI 3132, that - if I remember rightly - also had such problems, but they started after a greater amount of data. (At that time a Windows XP x64 installation had no problems, too.) If you need or want additional information or tests, let me know. Matthias 00:00.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD/ATI] RS690 Host Bridge [1002:7910] Subsystem: Gigabyte Technology Co., Ltd RS690 Host Bridge [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 32 NUMA node: 0 00:02.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] RS690 PCI to PCI Bridge (PCI Express Graphics Port 0) [1002:7913] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin ? routed to IRQ 24 NUMA node: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdd00000-fddfffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag+ RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us ClockPM- Surprise- LLActRep+ BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #2, PowerLimit 75.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+ RootCap: CRSVisible+ RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 41b1 Capabilities: [b0] Subsystem: Gigabyte Technology Co., Ltd RS690 PCI to PCI Bridge (PCI Express Graphics Port 0) [1458:5000] Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport Kernel modules: shpchp 00:04.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] Device [1002:7914] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin ? routed to IRQ 25 NUMA node: 0 Bus: primary=00, secondary=02, subordinate=05, sec-latency=0 I/O behind bridge: 0000d000-0000efff Memory behind bridge: fdb00000-fdcfffff Prefetchable memory behind bridge: 00000000fde00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag+ RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us ClockPM- Surprise- LLActRep+ BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #4, PowerLimit 25.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+ RootCap: CRSVisible+ RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0f00c Data: 41c1 Capabilities: [b0] Subsystem: Gigabyte Technology Co., Ltd Device [1458:5000] Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 Non-Raid-5 SATA [1002:4380] (prog-if 01 [AHCI 1.0]) Subsystem: Gigabyte Technology Co., Ltd Gigabyte GA-MA69G-S3H Motherboard [1458:b005] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 22 NUMA node: 0 Region 0: I/O ports at ff00 [size=8] Region 1: I/O ports at fe00 [size=4] Region 2: I/O ports at fd00 [size=8] Region 3: I/O ports at fc00 [size=4] Region 4: I/O ports at fb00 [size=16] Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ahci Kernel modules: ahci 00:13.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI0) [1002:4387] (prog-if 10 [OHCI]) Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI0) [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 NUMA node: 0 Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci Kernel modules: ohci_pci 00:13.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI1) [1002:4388] (prog-if 10 [OHCI]) Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI1) [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin B routed to IRQ 17 NUMA node: 0 Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci Kernel modules: ohci_pci 00:13.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI2) [1002:4389] (prog-if 10 [OHCI]) Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI2) [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin C routed to IRQ 18 NUMA node: 0 Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci Kernel modules: ohci_pci 00:13.3 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI3) [1002:438a] (prog-if 10 [OHCI]) Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI3) [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin B routed to IRQ 17 NUMA node: 0 Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci Kernel modules: ohci_pci 00:13.4 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI4) [1002:438b] (prog-if 10 [OHCI]) Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI4) [1458:5004] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin C routed to IRQ 18 NUMA node: 0 Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci Kernel modules: ohci_pci 00:13.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB Controller (EHCI) [1002:4386] (prog-if 20 [EHCI]) Subsystem: Gigabyte Technology Co., Ltd SB600 USB Controller (EHCI) [1458:5004] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin D routed to IRQ 19 NUMA node: 0 Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci-pci Kernel modules: ehci_pci 00:14.0 SMBus [0c05]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller [1002:4385] (rev 14) Subsystem: Gigabyte Technology Co., Ltd GA-MA770-DS3rev2.0 Motherboard [1458:4385] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- NUMA node: 0 Region 0: I/O ports at 0b00 [size=16] Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: piix4_smbus Kernel modules: i2c_piix4, sp5100_tco 00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 IDE [1002:438c] (prog-if 8a [Master SecP PriP]) Subsystem: Gigabyte Technology Co., Ltd Gigabyte GA-MA69G-S3H Motherboard [1458:5002] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 16 NUMA node: 0 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 Region 4: I/O ports at f900 [size=16] Kernel driver in use: pata_atiixp Kernel modules: pata_atiixp, ata_generic 00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) [1002:4383] Subsystem: Gigabyte Technology Co., Ltd GA-MA770-DS3rev2.0 Motherboard [1458:a022] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 NUMA node: 0 Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: snd_hda_intel Kernel modules: snd_hda_intel 00:14.3 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 PCI to LPC Bridge [1002:438d] Subsystem: Gigabyte Technology Co., Ltd SB600 PCI to LPC Bridge [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 NUMA node: 0 00:14.4 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 NUMA node: 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=64 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: fd900000-fd9fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor HyperTransport Configuration [1022:1200] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- NUMA node: 0 Capabilities: [80] HyperTransport: Host or Secondary Interface Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b- Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Revision ID: 3.00 Link Frequency: 1.0GHz Link Error: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE- 00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Address Map [1022:1201] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- NUMA node: 0 00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor DRAM Controller [1022:1202] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- NUMA node: 0 00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Miscellaneous Control [1022:1203] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- NUMA node: 0 Capabilities: [f0] Secure device <?> Kernel driver in use: k10temp Kernel modules: k10temp 00:18.4 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Link Control [1022:1204] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- NUMA node: 0 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Cape Verde LE [Radeon HD 7730/8730] [1002:6837] (prog-if 00 [VGA controller]) Subsystem: Hightech Information System Ltd. Cape Verde LE [Radeon HD 7730/8730] [1787:2330] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 34 NUMA node: 0 Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 2: Memory at fdd80000 (64-bit, non-prefetchable) [size=256K] Region 4: I/O ports at ce00 [size=256] [virtual] Expansion ROM at 000c0000 [disabled] [size=128K] Capabilities: [48] Vendor Specific Information: Len=08 <?> Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 4143 Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> Capabilities: [150 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [270 v1] #19 Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Cape Verde/Pitcairn HDMI Audio [Radeon HD 7700/7800 Series] [1002:aab0] Subsystem: Hightech Information System Ltd. Cape Verde/Pitcairn HDMI Audio [Radeon HD 7700/7800 Series] [1787:aab0] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin B routed to IRQ 4 NUMA node: 0 Region 0: Memory at fddfc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [48] Vendor Specific Information: Len=08 <?> Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> Capabilities: [150 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Kernel modules: snd_hda_intel 02:00.0 PCI bridge [0604]: Pericom Semiconductor Device [12d8:2304] (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes NUMA node: 0 Bus: primary=02, secondary=03, subordinate=05, sec-latency=0 I/O behind bridge: 0000d000-0000efff Memory behind bridge: fdb00000-fdcfffff Prefetchable memory behind bridge: 00000000fde00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [5c] Vital Product Data Not readable Capabilities: [64] Vendor Specific Information: Len=34 <?> Capabilities: [b0] Subsystem: Device [0000:0000] Capabilities: [c0] Express (v2) Upstream Port, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 5GT/s, Width x2, ASPM not supported, Exit Latency L0s <512ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Via message DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=4 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=04 MaxTimeSlots=64 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128+ TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Port Arbitration Table <?> Capabilities: [20c v1] Power Budgeting <?> Capabilities: [230 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Kernel driver in use: pcieport Kernel modules: shpchp 03:01.0 PCI bridge [0604]: Pericom Semiconductor Device [12d8:2304] (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin ? routed to IRQ 26 NUMA node: 0 Bus: primary=03, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [4c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 41d1 Capabilities: [64] Vendor Specific Information: Len=34 <?> Capabilities: [b0] Subsystem: Device [0000:0000] Capabilities: [c0] Express (v2) Downstream Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s <512ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp- LnkCtl: ASPM Disabled; Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #0, PowerLimit 0.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState+ DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Via message ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=4 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=04 MaxTimeSlots=64 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128+ TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Port Arbitration Table <?> Capabilities: [20c v1] Power Budgeting <?> Capabilities: [220 v1] Access Control Services ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl+ DirectTrans+ ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans- Kernel driver in use: pcieport Kernel modules: shpchp 03:02.0 PCI bridge [0604]: Pericom Semiconductor Device [12d8:2304] (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin ? routed to IRQ 27 NUMA node: 0 Bus: primary=03, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fdb00000-fdbfffff Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [4c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 41e1 Capabilities: [64] Vendor Specific Information: Len=34 <?> Capabilities: [b0] Subsystem: Device [0000:0000] Capabilities: [c0] Express (v2) Downstream Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM not supported, Exit Latency L0s <512ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp- LnkCtl: ASPM Disabled; Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #0, PowerLimit 0.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState+ DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Via message ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=4 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=04 MaxTimeSlots=64 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128+ TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Port Arbitration Table <?> Capabilities: [20c v1] Power Budgeting <?> Capabilities: [220 v1] Access Control Services ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl+ DirectTrans+ ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans- Kernel driver in use: pcieport Kernel modules: shpchp 04:00.0 USB controller [0c03]: Fresco Logic FL1100 USB 3.0 Host Controller [1b73:1100] (rev 10) (prog-if 30 [XHCI]) Subsystem: Sonnet Technologies, Inc. FL1100 USB 3.0 Host Controller [16b8:6e02] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 17 NUMA node: 0 Region 0: Memory at fdce0000 (64-bit, non-prefetchable) [size=64K] Region 2: Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at fdcfe000 (64-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [b0] MSI-X: Enable+ Count=8 Masked- Vector table: BAR=2 offset=00000000 PBA: BAR=4 offset=00000000 Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Kernel driver in use: xhci_hcd Kernel modules: xhci_pci 05:00.0 FireWire (IEEE 1394) [0c00]: LSI Corporation FW643 [TrueFire] PCIe 1394b Controller [11c1:5901] (rev 08) (prog-if 10 [OHCI]) Subsystem: Sonnet Technologies, Inc. FW643 [TrueFire] PCIe 1394b Controller [16b8:6e11] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 28 NUMA node: 0 Region 0: Memory at fdbff000 (64-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ Capabilities: [4c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 4182 Capabilities: [60] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 2048 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM not supported, Exit Latency L0s <512ns, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00 Status: NegoPending- InProgress- Capabilities: [170 v1] Device Serial Number 00-30-93-00-00-00-01-c3 Kernel driver in use: firewire_ohci Kernel modules: firewire_ohci 06:06.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller [1095:3124] (rev 02) Subsystem: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller [1095:7124] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 128, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 20 NUMA node: 0 Region 0: Memory at fdaff000 (64-bit, non-prefetchable) [size=128] Region 2: Memory at fdaf0000 (64-bit, non-prefetchable) [size=32K] Region 4: I/O ports at bf00 [size=16] [virtual] Expansion ROM at fd900000 [disabled] [size=512K] Capabilities: [64] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [40] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=12 Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz- Capabilities: [54] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: sata_sil24 Kernel modules: sata_sil24 06:07.0 Multimedia audio controller [0401]: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller [1412:1712] (rev 02) Subsystem: TERRATEC Electronic GmbH DMX 6fire 24/96 [153b:1138] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 21 NUMA node: 0 Region 0: I/O ports at be00 [size=32] Region 1: I/O ports at bd00 [size=16] Region 2: I/O ports at bc00 [size=16] Region 3: I/O ports at bb00 [size=64] Capabilities: [80] Power Management version 1 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: snd_ice1712 Kernel modules: snd_ice1712 06:0e.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI]) Subsystem: Gigabyte Technology Co., Ltd Motherboard [1458:1000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 1000ns max), Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 22 NUMA node: 0 Region 0: Memory at fdafe000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at fdaf8000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: firewire_ohci Kernel modules: firewire_ohci 06:0f.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10) Subsystem: Gigabyte Technology Co., Ltd GA-MA69G-S3H Motherboard [1458:e000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 23 NUMA node: 0 Region 0: I/O ports at b800 [size=256] Region 1: Memory at fdafd000 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at fd980000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: r8169 Kernel modules: r8169 [ 0.000000] Linux version 4.9.2 (root@c21) (gcc version 6.3.0 20161229 (Debian 6.3.0-2) ) #1 SMP Fri Jan 13 20:21:28 CET 2017 [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-4.9.2 root=/dev/md127p2 ro printk.time=1 single video=DVI-D-1:1920x1200-8@60D video=VGA-1:d video=HDMI-A-1:d [ 0.000000] x86/fpu: Legacy x87 FPU detected. [ 0.000000] x86/fpu: Using 'eager' FPU context switches. [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x00000000000997ff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cfedffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000cfee0000-0x00000000cfee2fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000cfee3000-0x00000000cfeeffff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000cfef0000-0x00000000cfefffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000022fffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI not present or invalid. [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] AGP: No AGP bridge found [ 0.000000] e820: last_pfn = 0x230000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-C7FFF write-protect [ 0.000000] C8000-FFFFF uncachable [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back [ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back [ 0.000000] 2 base 0000C0000000 mask FFFFF0000000 write-back [ 0.000000] 3 base 0000CFF00000 mask FFFFFFF00000 uncachable [ 0.000000] 4 base 000100000000 mask FFFF00000000 write-back [ 0.000000] 5 base 000200000000 mask FFFFE0000000 write-back [ 0.000000] 6 base 000220000000 mask FFFFF0000000 write-back [ 0.000000] 7 disabled [ 0.000000] TOM2: 0000000230000000 aka 8960M [ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT [ 0.000000] e820: update [mem 0xcff00000-0xffffffff] usable ==> reserved [ 0.000000] e820: last_pfn = 0xcfee0 max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [mem 0x000f4f50-0x000f4f5f] mapped at [ffff89b3400f4f50] [ 0.000000] Base memory trampoline at [ffff89b340093000] 93000 size 24576 [ 0.000000] Using GB pages for direct mapping [ 0.000000] BRK [0x207d4a000, 0x207d4afff] PGTABLE [ 0.000000] BRK [0x207d4b000, 0x207d4bfff] PGTABLE [ 0.000000] BRK [0x207d4c000, 0x207d4cfff] PGTABLE [ 0.000000] BRK [0x207d4d000, 0x207d4dfff] PGTABLE [ 0.000000] BRK [0x207d4e000, 0x207d4efff] PGTABLE [ 0.000000] BRK [0x207d4f000, 0x207d4ffff] PGTABLE [ 0.000000] BRK [0x207d50000, 0x207d50fff] PGTABLE [ 0.000000] RAMDISK: [mem 0x3626b000-0x3712cfff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000F6920 000014 (v00 GBT ) [ 0.000000] ACPI: RSDT 0x00000000CFEE3000 000038 (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.000000] ACPI: FACP 0x00000000CFEE3040 000074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.000000] ACPI: DSDT 0x00000000CFEE30C0 00494D (v01 GBT GBTUACPI 00001000 MSFT 03000000) [ 0.000000] ACPI: FACS 0x00000000CFEE0000 000040 [ 0.000000] ACPI: SSDT 0x00000000CFEE7B00 00088C (v01 PTLTD POWERNOW 00000001 LTP 00000001) [ 0.000000] ACPI: HPET 0x00000000CFEE83C0 000038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098) [ 0.000000] ACPI: MCFG 0x00000000CFEE8400 00003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.000000] ACPI: APIC 0x00000000CFEE7A40 000084 (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] Scanning NUMA topology in Northbridge 24 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000022fffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x22fffb000-0x22fffffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000022fffffff] [ 0.000000] Device empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x0000000000098fff] [ 0.000000] node 0: [mem 0x0000000000100000-0x00000000cfedffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000022fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000022fffffff] [ 0.000000] On node 0 totalpages: 2096760 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 21 pages reserved [ 0.000000] DMA zone: 3992 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 13244 pages used for memmap [ 0.000000] DMA32 zone: 847584 pages, LIFO batch:31 [ 0.000000] Normal zone: 19456 pages used for memmap [ 0.000000] Normal zone: 1245184 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) [ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x10b9a201 base: 0xfed00000 [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x00099000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0xcfee0000-0xcfee2fff] [ 0.000000] PM: Registered nosave memory: [mem 0xcfee3000-0xcfeeffff] [ 0.000000] PM: Registered nosave memory: [mem 0xcfef0000-0xcfefffff] [ 0.000000] PM: Registered nosave memory: [mem 0xcff00000-0xdfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfebfffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xffffffff] [ 0.000000] e820: [mem 0xcff00000-0xdfffffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns [ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] percpu: Embedded 35 pages/cpu @ffff89b56fc00000 s103768 r8192 d31400 u524288 [ 0.000000] pcpu-alloc: s103768 r8192 d31400 u524288 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 2063975 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-4.9.2 root=/dev/md127p2 ro printk.time=1 single video=DVI-D-1:1920x1200-8@60D video=VGA-1:d video=HDMI-A-1:d [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] AGP: Checking aperture... [ 0.000000] AGP: No AGP bridge found [ 0.000000] AGP: Node 0: aperture [bus addr 0xc4000000-0xc5ffffff] (32MB) [ 0.000000] Aperture pointing to e820 RAM. Ignoring. [ 0.000000] AGP: Your BIOS doesn't leave an aperture memory hole [ 0.000000] AGP: Please enable the IOMMU option in the BIOS setup [ 0.000000] AGP: This costs you 64MB of RAM [ 0.000000] AGP: Mapping aperture over RAM [mem 0xc4000000-0xc7ffffff] (65536KB) [ 0.000000] PM: Registered nosave memory: [mem 0xc4000000-0xc7ffffff] [ 0.000000] Memory: 8092940K/8387040K available (6138K kernel code, 1134K rwdata, 2812K rodata, 1388K init, 812K bss, 294100K reserved, 0K cma-reserved) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:33024 nr_irqs:456 16 [ 0.000000] spurious 8259A interrupt: IRQ7. [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns [ 0.000000] hpet clockevent registered [ 0.000000] tsc: Fast TSC calibration failed [ 0.000000] tsc: Unable to calibrate against PIT [ 0.000000] tsc: using HPET reference calibration [ 0.000000] tsc: Detected 3207.269 MHz processor [ 0.000019] Calibrating delay loop (skipped), value calculated using timer frequency.. 6414.53 BogoMIPS (lpj=12829076) [ 0.000108] pid_max: default: 32768 minimum: 301 [ 0.000167] ACPI: Core revision 20160831 [ 0.002721] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.002856] Security Framework initialized [ 0.002901] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.002951] AppArmor: AppArmor disabled by boot time parameter [ 0.003356] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.006310] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.007570] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.007623] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.008007] CPU: Physical Processor ID: 0 [ 0.008051] CPU: Processor Core ID: 0 [ 0.008095] mce: CPU supports 6 MCE banks [ 0.008143] LVT offset 0 assigned for vector 0xf9 [ 0.008191] Last level iTLB entries: 4KB 512, 2MB 16, 4MB 8 [ 0.008235] Last level dTLB entries: 4KB 512, 2MB 128, 4MB 64, 1GB 0 [ 0.008508] Freeing SMP alternatives memory: 24K (ffffffffb6478000 - ffffffffb647e000) [ 0.035545] ftrace: allocating 24972 entries in 98 pages [ 0.043263] smpboot: Max logical packages: 1 [ 0.043864] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.189342] smpboot: CPU0: AMD Phenom(tm) II X4 955 Processor (family: 0x10, model: 0x4, stepping: 0x3) [ 0.189506] Performance Events: AMD PMU driver. [ 0.189589] ... version: 0 [ 0.189632] ... bit width: 48 [ 0.189675] ... generic registers: 4 [ 0.189718] ... value mask: 0000ffffffffffff [ 0.189761] ... max period: 00007fffffffffff [ 0.189805] ... fixed-purpose events: 0 [ 0.189847] ... event mask: 000000000000000f [ 0.190354] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. [ 0.190519] x86: Booting SMP configuration: [ 0.190563] .... node #0, CPUs: #1 #2 #3 [ 0.431417] x86: Booted up 1 node, 4 CPUs [ 0.431503] smpboot: Total of 4 processors activated (25657.97 BogoMIPS) [ 0.437278] devtmpfs: initialized [ 0.437394] x86/mm: Memory block size: 128MB [ 0.441042] PM: Registering ACPI NVS region [mem 0xcfee0000-0xcfee2fff] (12288 bytes) [ 0.441151] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.441236] pinctrl core: initialized pinctrl subsystem [ 0.441399] NET: Registered protocol family 16 [ 0.453359] cpuidle: using governor ladder [ 0.469358] cpuidle: using governor menu [ 0.469409] node 0 link 0: io port [b000, ffff] [ 0.469410] TOM: 00000000d0000000 aka 3328M [ 0.469454] Fam 10h mmconf [mem 0xe0000000-0xe00fffff] [ 0.469456] node 0 link 0: mmio [a0000, bffff] [ 0.469457] node 0 link 0: mmio [d0000000, dfffffff] [ 0.469459] node 0 link 0: mmio [f0000000, fe02ffff] [ 0.469460] node 0 link 0: mmio [e0000000, e06fffff] ==> [e0100000, e06fffff] [ 0.469461] TOM2: 0000000230000000 aka 8960M [ 0.469505] bus: [bus 00-06] on node 0 link 0 [ 0.469506] bus: 00 [io 0x0000-0xffff] [ 0.469507] bus: 00 [mem 0x000a0000-0x000bffff] [ 0.469507] bus: 00 [mem 0xd0000000-0xdfffffff] [ 0.469508] bus: 00 [mem 0xe0700000-0xffffffff] [ 0.469508] bus: 00 [mem 0xe0100000-0xe06fffff] [ 0.469509] bus: 00 [mem 0x230000000-0xfcffffffff] [ 0.469574] ACPI: bus type PCI registered [ 0.469618] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.469699] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.469749] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820 [ 0.469810] PCI: Using configuration type 1 for base access [ 0.470144] mtrr: your CPUs had inconsistent variable MTRR settings [ 0.470189] mtrr: probably your BIOS does not setup all CPUs. [ 0.470232] mtrr: corrected configuration. [ 0.485543] HugeTLB registered 1 GB page size, pre-allocated 0 pages [ 0.485590] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.485975] ACPI: Added _OSI(Module Device) [ 0.486022] ACPI: Added _OSI(Processor Device) [ 0.486066] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.486109] ACPI: Added _OSI(Processor Aggregator Device) [ 0.486328] ACPI: Executed 1 blocks of module-level executable AML code [ 0.491141] ACPI: Interpreter enabled [ 0.491197] ACPI: (supports S0 S3 S4 S5) [ 0.491240] ACPI: Using IOAPIC for interrupt routing [ 0.491336] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.495034] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.495084] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI] [ 0.495135] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM [ 0.495393] PCI host bridge to bus 0000:00 [ 0.495438] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.495483] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.495528] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.498051] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window] [ 0.498100] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfebfffff window] [ 0.498149] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.498198] pci 0000:00:00.0: [1002:7910] type 00 class 0x060000 [ 0.498279] pci 0000:00:02.0: [1002:7913] type 01 class 0x060400 [ 0.498308] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold [ 0.498346] pci 0000:00:02.0: System wakeup disabled by ACPI [ 0.498424] pci 0000:00:04.0: [1002:7914] type 01 class 0x060400 [ 0.498451] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold [ 0.498485] pci 0000:00:04.0: System wakeup disabled by ACPI [ 0.498582] pci 0000:00:12.0: [1002:4380] type 00 class 0x010601 [ 0.498598] pci 0000:00:12.0: reg 0x10: [io 0xff00-0xff07] [ 0.498607] pci 0000:00:12.0: reg 0x14: [io 0xfe00-0xfe03] [ 0.498616] pci 0000:00:12.0: reg 0x18: [io 0xfd00-0xfd07] [ 0.498624] pci 0000:00:12.0: reg 0x1c: [io 0xfc00-0xfc03] [ 0.498633] pci 0000:00:12.0: reg 0x20: [io 0xfb00-0xfb0f] [ 0.498642] pci 0000:00:12.0: reg 0x24: [mem 0xfe02f000-0xfe02f3ff] [ 0.498740] pci 0000:00:13.0: [1002:4387] type 00 class 0x0c0310 [ 0.498752] pci 0000:00:13.0: reg 0x10: [mem 0xfe02e000-0xfe02efff] [ 0.498843] pci 0000:00:13.0: System wakeup disabled by ACPI [ 0.498920] pci 0000:00:13.1: [1002:4388] type 00 class 0x0c0310 [ 0.498933] pci 0000:00:13.1: reg 0x10: [mem 0xfe02d000-0xfe02dfff] [ 0.499024] pci 0000:00:13.1: System wakeup disabled by ACPI [ 0.499101] pci 0000:00:13.2: [1002:4389] type 00 class 0x0c0310 [ 0.499114] pci 0000:00:13.2: reg 0x10: [mem 0xfe02c000-0xfe02cfff] [ 0.499204] pci 0000:00:13.2: System wakeup disabled by ACPI [ 0.499285] pci 0000:00:13.3: [1002:438a] type 00 class 0x0c0310 [ 0.499298] pci 0000:00:13.3: reg 0x10: [mem 0xfe02b000-0xfe02bfff] [ 0.499400] pci 0000:00:13.3: System wakeup disabled by ACPI [ 0.499477] pci 0000:00:13.4: [1002:438b] type 00 class 0x0c0310 [ 0.499490] pci 0000:00:13.4: reg 0x10: [mem 0xfe02a000-0xfe02afff] [ 0.499581] pci 0000:00:13.4: System wakeup disabled by ACPI [ 0.499661] pci 0000:00:13.5: [1002:4386] type 00 class 0x0c0320 [ 0.499678] pci 0000:00:13.5: reg 0x10: [mem 0xfe029000-0xfe0290ff] [ 0.499758] pci 0000:00:13.5: supports D1 D2 [ 0.499759] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot [ 0.499797] pci 0000:00:13.5: System wakeup disabled by ACPI [ 0.499879] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 [ 0.499899] pci 0000:00:14.0: reg 0x10: [io 0x0b00-0x0b0f] [ 0.500031] pci 0000:00:14.1: [1002:438c] type 00 class 0x01018a [ 0.500044] pci 0000:00:14.1: reg 0x10: [io 0x0000-0x0007] [ 0.500052] pci 0000:00:14.1: reg 0x14: [io 0x0000-0x0003] [ 0.500061] pci 0000:00:14.1: reg 0x18: [io 0x0000-0x0007] [ 0.500070] pci 0000:00:14.1: reg 0x1c: [io 0x0000-0x0003] [ 0.500079] pci 0000:00:14.1: reg 0x20: [io 0xf900-0xf90f] [ 0.500098] pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 0.500143] pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 0.500187] pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 0.500232] pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 0.500345] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300 [ 0.500365] pci 0000:00:14.2: reg 0x10: [mem 0xfe024000-0xfe027fff 64bit] [ 0.500432] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold [ 0.500469] pci 0000:00:14.2: System wakeup disabled by ACPI [ 0.500545] pci 0000:00:14.3: [1002:438d] type 00 class 0x060100 [ 0.500671] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 [ 0.500739] pci 0000:00:14.4: System wakeup disabled by ACPI [ 0.500819] pci 0000:00:18.0: [1022:1200] type 00 class 0x060000 [ 0.500883] pci 0000:00:18.1: [1022:1201] type 00 class 0x060000 [ 0.500942] pci 0000:00:18.2: [1022:1202] type 00 class 0x060000 [ 0.501000] pci 0000:00:18.3: [1022:1203] type 00 class 0x060000 [ 0.501061] pci 0000:00:18.4: [1022:1204] type 00 class 0x060000 [ 0.501166] pci 0000:01:00.0: [1002:6837] type 00 class 0x030000 [ 0.501181] pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.501191] pci 0000:01:00.0: reg 0x18: [mem 0xfdd80000-0xfddbffff 64bit] [ 0.501198] pci 0000:01:00.0: reg 0x20: [io 0xce00-0xceff] [ 0.501210] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref] [ 0.501255] pci 0000:01:00.0: supports D1 D2 [ 0.501256] pci 0000:01:00.0: PME# supported from D1 D2 D3hot [ 0.501312] pci 0000:01:00.1: [1002:aab0] type 00 class 0x040300 [ 0.501326] pci 0000:01:00.1: reg 0x10: [mem 0xfddfc000-0xfddfffff 64bit] [ 0.501402] pci 0000:01:00.1: supports D1 D2 [ 0.515403] pci 0000:00:02.0: PCI bridge to [bus 01] [ 0.515451] pci 0000:00:02.0: bridge window [io 0xc000-0xcfff] [ 0.515453] pci 0000:00:02.0: bridge window [mem 0xfdd00000-0xfddfffff] [ 0.515455] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.515534] pci 0000:02:00.0: [12d8:2304] type 01 class 0x060400 [ 0.515630] pci 0000:02:00.0: Max Payload Size set to 128 (was 256, max 256) [ 0.515785] pci 0000:02:00.0: supports D1 D2 [ 0.515786] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.527407] pci 0000:00:04.0: PCI bridge to [bus 02-05] [ 0.527455] pci 0000:00:04.0: bridge window [io 0xd000-0xefff] [ 0.527457] pci 0000:00:04.0: bridge window [mem 0xfdb00000-0xfdcfffff] [ 0.527459] pci 0000:00:04.0: bridge window [mem 0xfde00000-0xfdffffff 64bit pref] [ 0.527567] pci 0000:03:01.0: [12d8:2304] type 01 class 0x060400 [ 0.527642] pci 0000:03:01.0: Max Payload Size set to 128 (was 256, max 256) [ 0.527796] pci 0000:03:01.0: supports D1 D2 [ 0.527797] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.527896] pci 0000:03:02.0: [12d8:2304] type 01 class 0x060400 [ 0.527969] pci 0000:03:02.0: Max Payload Size set to 128 (was 256, max 256) [ 0.528114] pci 0000:03:02.0: supports D1 D2 [ 0.528114] pci 0000:03:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.528242] pci 0000:02:00.0: PCI bridge to [bus 03-05] [ 0.528294] pci 0000:02:00.0: bridge window [io 0xd000-0xefff] [ 0.528299] pci 0000:02:00.0: bridge window [mem 0xfdb00000-0xfdcfffff] [ 0.528307] pci 0000:02:00.0: bridge window [mem 0xfde00000-0xfdffffff 64bit pref] [ 0.528392] pci 0000:04:00.0: [1b73:1100] type 00 class 0x0c0330 [ 0.528424] pci 0000:04:00.0: reg 0x10: [mem 0xfdce0000-0xfdceffff 64bit] [ 0.528445] pci 0000:04:00.0: reg 0x18: [mem 0xfdcff000-0xfdcfffff 64bit] [ 0.528467] pci 0000:04:00.0: reg 0x20: [mem 0xfdcfe000-0xfdcfefff 64bit] [ 0.528492] pci 0000:04:00.0: Max Payload Size set to 128 (was 256, max 512) [ 0.528611] pci 0000:04:00.0: supports D1 [ 0.528612] pci 0000:04:00.0: PME# supported from D0 D1 D3hot [ 0.528701] pci 0000:03:01.0: PCI bridge to [bus 04] [ 0.528752] pci 0000:03:01.0: bridge window [io 0xe000-0xefff] [ 0.528757] pci 0000:03:01.0: bridge window [mem 0xfdc00000-0xfdcfffff] [ 0.528765] pci 0000:03:01.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.528852] pci 0000:05:00.0: [11c1:5901] type 00 class 0x0c0010 [ 0.528884] pci 0000:05:00.0: reg 0x10: [mem 0xfdbff000-0xfdbfffff 64bit] [ 0.528962] pci 0000:05:00.0: Max Payload Size set to 128 (was 256, max 256) [ 0.529090] pci 0000:05:00.0: supports D1 D2 [ 0.529090] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot [ 0.539412] pci 0000:03:02.0: PCI bridge to [bus 05] [ 0.539467] pci 0000:03:02.0: bridge window [io 0xd000-0xdfff] [ 0.539472] pci 0000:03:02.0: bridge window [mem 0xfdb00000-0xfdbfffff] [ 0.539480] pci 0000:03:02.0: bridge window [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.539573] pci 0000:06:06.0: [1095:3124] type 00 class 0x010400 [ 0.539604] pci 0000:06:06.0: reg 0x10: [mem 0xfdaff000-0xfdaff07f 64bit] [ 0.539623] pci 0000:06:06.0: reg 0x18: [mem 0xfdaf0000-0xfdaf7fff 64bit] [ 0.539635] pci 0000:06:06.0: reg 0x20: [io 0xbf00-0xbf0f] [ 0.539659] pci 0000:06:06.0: reg 0x30: [mem 0x00000000-0x0007ffff pref] [ 0.539723] pci 0000:06:06.0: supports D1 D2 [ 0.539769] pci 0000:06:07.0: [1412:1712] type 00 class 0x040100 [ 0.539789] pci 0000:06:07.0: reg 0x10: [io 0xbe00-0xbe1f] [ 0.539800] pci 0000:06:07.0: reg 0x14: [io 0xbd00-0xbd0f] [ 0.539812] pci 0000:06:07.0: reg 0x18: [io 0xbc00-0xbc0f] [ 0.539823] pci 0000:06:07.0: reg 0x1c: [io 0xbb00-0xbb3f] [ 0.539891] pci 0000:06:07.0: supports D2 [ 0.539938] pci 0000:06:0e.0: [104c:8024] type 00 class 0x0c0010 [ 0.539959] pci 0000:06:0e.0: reg 0x10: [mem 0xfdafe000-0xfdafe7ff] [ 0.539971] pci 0000:06:0e.0: reg 0x14: [mem 0xfdaf8000-0xfdafbfff] [ 0.540064] pci 0000:06:0e.0: supports D1 D2 [ 0.540065] pci 0000:06:0e.0: PME# supported from D0 D1 D2 D3hot [ 0.540113] pci 0000:06:0f.0: [10ec:8167] type 00 class 0x020000 [ 0.540132] pci 0000:06:0f.0: reg 0x10: [io 0xb800-0xb8ff] [ 0.540143] pci 0000:06:0f.0: reg 0x14: [mem 0xfdafd000-0xfdafd0ff] [ 0.540196] pci 0000:06:0f.0: reg 0x30: [mem 0x00000000-0x0001ffff pref] [ 0.540230] pci 0000:06:0f.0: supports D1 D2 [ 0.540231] pci 0000:06:0f.0: PME# supported from D1 D2 D3hot D3cold [ 0.540292] pci 0000:00:14.4: PCI bridge to [bus 06] (subtractive decode) [ 0.540339] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff] [ 0.540342] pci 0000:00:14.4: bridge window [mem 0xfda00000-0xfdafffff] [ 0.540345] pci 0000:00:14.4: bridge window [mem 0xfd900000-0xfd9fffff pref] [ 0.540346] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.540347] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.540348] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 0.540349] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode) [ 0.540350] pci 0000:00:14.4: bridge window [mem 0xd0000000-0xfebfffff window] (subtractive decode) [ 0.540500] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.541005] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.541508] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.542010] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.542511] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.543013] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.543519] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.544019] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 0.544990] ACPI: Enabled 1 GPEs in block 00 to 1F [ 0.545252] vgaarb: setting as boot device: PCI:0000:01:00.0 [ 0.545297] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none [ 0.545346] vgaarb: loaded [ 0.545389] vgaarb: bridge control possible 0000:01:00.0 [ 0.545464] dmi: Firmware registration failed. [ 0.545561] PCI: Using ACPI for IRQ routing [ 0.554455] PCI: pci_cache_line_size set to 64 bytes [ 0.554534] e820: reserve RAM buffer [mem 0x00099800-0x0009ffff] [ 0.554535] e820: reserve RAM buffer [mem 0xcfee0000-0xcfffffff] [ 0.554750] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 0.554985] hpet0: 4 comparators, 32-bit 14.318180 MHz counter [ 0.557091] clocksource: Switched to clocksource hpet [ 0.563981] VFS: Disk quotas dquot_6.6.0 [ 0.564050] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.564175] pnp: PnP ACPI init [ 0.564332] system 00:00: [io 0x04d0-0x04d1] has been reserved [ 0.564377] system 00:00: [io 0x0220-0x0225] has been reserved [ 0.564421] system 00:00: [io 0x0290-0x0294] has been reserved [ 0.564467] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.564626] pnp 00:01: disabling [mem 0x00000000-0x00000fff window] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref] [ 0.564682] pnp 00:01: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:06:06.0 BAR 6 [mem 0x00000000-0x0007ffff pref] [ 0.564736] pnp 00:01: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:06:0f.0 BAR 6 [mem 0x00000000-0x0001ffff pref] [ 0.564806] system 00:01: [io 0x4100-0x411f] has been reserved [ 0.564851] system 00:01: [io 0x0228-0x022f] has been reserved [ 0.564895] system 00:01: [io 0x040b] has been reserved [ 0.564939] system 00:01: [io 0x04d6] has been reserved [ 0.564983] system 00:01: [io 0x0c00-0x0c01] has been reserved [ 0.565027] system 00:01: [io 0x0c14] has been reserved [ 0.565072] system 00:01: [io 0x0c50-0x0c52] has been reserved [ 0.565128] system 00:01: [io 0x0c6c-0x0c6d] has been reserved [ 0.565173] system 00:01: [io 0x0c6f] has been reserved [ 0.565217] system 00:01: [io 0x0cd0-0x0cd1] has been reserved [ 0.565261] system 00:01: [io 0x0cd2-0x0cd3] has been reserved [ 0.565306] system 00:01: [io 0x0cd4-0x0cdf] has been reserved [ 0.565350] system 00:01: [io 0x4000-0x40fe] has been reserved [ 0.565394] system 00:01: [io 0x4210-0x4217] has been reserved [ 0.565439] system 00:01: [io 0x0b00-0x0b1f] could not be reserved [ 0.565483] system 00:01: [io 0x0238-0x023f] has been reserved [ 0.565528] system 00:01: [mem 0xfee00400-0xfee00fff window] has been reserved [ 0.565577] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.565704] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.565823] pnp 00:03: [dma 2] [ 0.565847] pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active) [ 0.566092] pnp 00:04: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.566330] pnp 00:05: [dma 3] [ 0.566362] pnp 00:05: Plug and Play ACPI device, IDs PNP0401 (active) [ 0.566435] system 00:06: [mem 0xe0000000-0xefffffff] has been reserved [ 0.566481] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.566613] system 00:07: [mem 0x000d6000-0x000d7fff] has been reserved [ 0.566659] system 00:07: [mem 0x000f0000-0x000f7fff] could not be reserved [ 0.566703] system 00:07: [mem 0x000f8000-0x000fbfff] could not be reserved [ 0.566748] system 00:07: [mem 0x000fc000-0x000fffff] could not be reserved [ 0.566792] system 00:07: [mem 0xcfee0000-0xcfefffff] could not be reserved [ 0.566837] system 00:07: [mem 0xffff0000-0xffffffff] has been reserved [ 0.566882] system 00:07: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.566926] system 00:07: [mem 0x00100000-0xcfedffff] could not be reserved [ 0.566971] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.567016] system 00:07: [mem 0xfee00000-0xfee00fff] could not be reserved [ 0.567060] system 00:07: [mem 0xfff80000-0xfffeffff] has been reserved [ 0.567105] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.567118] pnp: PnP ACPI: found 8 devices [ 0.573881] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.573989] pci 0000:01:00.0: BAR 6: assigned [mem 0xfdd00000-0xfdd1ffff pref] [ 0.574038] pci 0000:00:02.0: PCI bridge to [bus 01] [ 0.574083] pci 0000:00:02.0: bridge window [io 0xc000-0xcfff] [ 0.574128] pci 0000:00:02.0: bridge window [mem 0xfdd00000-0xfddfffff] [ 0.574173] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.574223] pci 0000:03:01.0: PCI bridge to [bus 04] [ 0.574269] pci 0000:03:01.0: bridge window [io 0xe000-0xefff] [ 0.574319] pci 0000:03:01.0: bridge window [mem 0xfdc00000-0xfdcfffff] [ 0.574367] pci 0000:03:01.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.574422] pci 0000:03:02.0: PCI bridge to [bus 05] [ 0.574468] pci 0000:03:02.0: bridge window [io 0xd000-0xdfff] [ 0.574518] pci 0000:03:02.0: bridge window [mem 0xfdb00000-0xfdbfffff] [ 0.574566] pci 0000:03:02.0: bridge window [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.574621] pci 0000:02:00.0: PCI bridge to [bus 03-05] [ 0.574667] pci 0000:02:00.0: bridge window [io 0xd000-0xefff] [ 0.574717] pci 0000:02:00.0: bridge window [mem 0xfdb00000-0xfdcfffff] [ 0.574765] pci 0000:02:00.0: bridge window [mem 0xfde00000-0xfdffffff 64bit pref] [ 0.574820] pci 0000:00:04.0: PCI bridge to [bus 02-05] [ 0.574864] pci 0000:00:04.0: bridge window [io 0xd000-0xefff] [ 0.574909] pci 0000:00:04.0: bridge window [mem 0xfdb00000-0xfdcfffff] [ 0.574954] pci 0000:00:04.0: bridge window [mem 0xfde00000-0xfdffffff 64bit pref] [ 0.575005] pci 0000:06:06.0: BAR 6: assigned [mem 0xfd900000-0xfd97ffff pref] [ 0.575054] pci 0000:06:0f.0: BAR 6: assigned [mem 0xfd980000-0xfd99ffff pref] [ 0.575103] pci 0000:00:14.4: PCI bridge to [bus 06] [ 0.575147] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff] [ 0.575195] pci 0000:00:14.4: bridge window [mem 0xfda00000-0xfdafffff] [ 0.575241] pci 0000:00:14.4: bridge window [mem 0xfd900000-0xfd9fffff pref] [ 0.575295] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.575296] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.575297] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.575298] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff window] [ 0.575299] pci_bus 0000:00: resource 8 [mem 0xd0000000-0xfebfffff window] [ 0.575300] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff] [ 0.575301] pci_bus 0000:01: resource 1 [mem 0xfdd00000-0xfddfffff] [ 0.575301] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.575303] pci_bus 0000:02: resource 0 [io 0xd000-0xefff] [ 0.575303] pci_bus 0000:02: resource 1 [mem 0xfdb00000-0xfdcfffff] [ 0.575304] pci_bus 0000:02: resource 2 [mem 0xfde00000-0xfdffffff 64bit pref] [ 0.575305] pci_bus 0000:03: resource 0 [io 0xd000-0xefff] [ 0.575306] pci_bus 0000:03: resource 1 [mem 0xfdb00000-0xfdcfffff] [ 0.575307] pci_bus 0000:03: resource 2 [mem 0xfde00000-0xfdffffff 64bit pref] [ 0.575308] pci_bus 0000:04: resource 0 [io 0xe000-0xefff] [ 0.575309] pci_bus 0000:04: resource 1 [mem 0xfdc00000-0xfdcfffff] [ 0.575310] pci_bus 0000:04: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.575311] pci_bus 0000:05: resource 0 [io 0xd000-0xdfff] [ 0.575312] pci_bus 0000:05: resource 1 [mem 0xfdb00000-0xfdbfffff] [ 0.575313] pci_bus 0000:05: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.575314] pci_bus 0000:06: resource 0 [io 0xb000-0xbfff] [ 0.575315] pci_bus 0000:06: resource 1 [mem 0xfda00000-0xfdafffff] [ 0.575316] pci_bus 0000:06: resource 2 [mem 0xfd900000-0xfd9fffff pref] [ 0.575317] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7 window] [ 0.575318] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff window] [ 0.575318] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.575319] pci_bus 0000:06: resource 7 [mem 0x000c0000-0x000dffff window] [ 0.575320] pci_bus 0000:06: resource 8 [mem 0xd0000000-0xfebfffff window] [ 0.575424] NET: Registered protocol family 2 [ 0.575655] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.575878] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.576242] TCP: Hash tables configured (established 65536 bind 65536) [ 0.576341] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.576436] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.576569] NET: Registered protocol family 1 [ 1.037374] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 1.037547] PCI: CLS 4 bytes, default 64 [ 1.037596] Unpacking initramfs... [ 2.404026] Freeing initrd memory: 15112K (ffff89b37626b000 - ffff89b37712d000) [ 2.404368] PCI-DMA: Disabling AGP. [ 2.404511] PCI-DMA: aperture base @ c4000000 size 65536 KB [ 2.404555] PCI-DMA: using GART IOMMU. [ 2.404600] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 2.407924] LVT offset 1 assigned for vector 0x400 [ 2.407981] IBS: LVT offset 1 assigned [ 2.408157] perf: AMD IBS detected (0x0000001f) [ 2.408524] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 2.408596] audit: initializing netlink subsys (disabled) [ 2.408663] audit: type=2000 audit(1484393533.296:1): initialized [ 2.408974] Initialise system trusted keyrings [ 2.409193] workingset: timestamp_bits=40 max_order=21 bucket_order=0 [ 2.409293] zbud: loaded [ 2.454442] Key type asymmetric registered [ 2.454491] Asymmetric key parser 'x509' registered [ 2.454576] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 2.454664] io scheduler noop registered [ 2.454708] io scheduler deadline registered [ 2.454755] io scheduler cfq registered (default) [ 2.455507] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 2.455555] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 2.455758] GHES: HEST is not enabled! [ 2.455870] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.476468] 00:04: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.476941] Linux agpgart interface v0.103 [ 2.477012] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de> [ 2.477056] AMD IOMMUv2 functionality not available on this system [ 2.479968] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 2.513615] i8042: Failed to disable AUX port, but continuing anyway... Is this a SiS? [ 2.513663] i8042: If AUX port is really absent please use the 'i8042.noaux' option [ 2.797233] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.797443] mousedev: PS/2 mouse device common for all mice [ 2.797535] rtc_cmos 00:02: RTC can wake from S4 [ 2.797692] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 2.797771] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram, hpet irqs [ 2.797909] ledtrig-cpu: registered to indicate activity on CPUs [ 2.797952] dmi-sysfs: dmi entry is absent. [ 2.798119] NET: Registered protocol family 10 [ 2.798377] mip6: Mobile IPv6 [ 2.798421] NET: Registered protocol family 17 [ 2.798466] mpls_gso: MPLS GSO support [ 2.798730] microcode: CPU0: patch_level=0x010000af [ 2.798783] microcode: CPU1: patch_level=0x010000af [ 2.798844] microcode: CPU2: patch_level=0x010000af [ 2.798909] microcode: CPU3: patch_level=0x010000af [ 2.798992] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba [ 2.799165] registered taskstats version 1 [ 2.799210] Loading compiled-in X.509 certificates [ 2.799265] zswap: loaded using pool lzo/zbud [ 2.799749] rtc_cmos 00:02: setting system clock to 2017-01-14 11:32:13 UTC (1484393533) [ 2.799844] PM: Hibernation image not present or could not be loaded. [ 2.801085] Freeing unused kernel memory: 1388K (ffffffffb631d000 - ffffffffb6478000) [ 2.801160] Write protecting the kernel read-only data: 12288k [ 2.801844] Freeing unused kernel memory: 2040K (ffff89b547402000 - ffff89b547600000) [ 2.804783] Freeing unused kernel memory: 1284K (ffff89b5478bf000 - ffff89b547a00000) [ 2.810210] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 2.823232] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.823338] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.823390] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.823443] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.824136] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.824211] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.825023] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.825386] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.825480] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.825568] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.842139] fjes: module verification failed: signature and/or required key missing - tainting kernel [ 2.842553] FUJITSU Extended Socket Network Device Driver - version 1.1 - Copyright (c) 2015 FUJITSU LIMITED [ 2.843356] Floppy drive(s): fd0 is 1.44M [ 2.848479] SCSI subsystem initialized [ 2.849152] ACPI: bus type USB registered [ 2.849221] usbcore: registered new interface driver usbfs [ 2.849274] usbcore: registered new interface driver hub [ 2.849337] usbcore: registered new device driver usb [ 2.849584] [drm] Initialized [ 2.849832] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.850434] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.850734] ehci-pci: EHCI PCI platform driver [ 2.850893] libata version 3.00 loaded. [ 2.850976] ehci-pci 0000:00:13.5: EHCI Host Controller [ 2.851031] ehci-pci 0000:00:13.5: new USB bus registered, assigned bus number 1 [ 2.851088] ehci-pci 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround [ 2.851150] ehci-pci 0000:00:13.5: debug port 1 [ 2.851253] ehci-pci 0000:00:13.5: irq 19, io mem 0xfe029000 [ 2.852904] sata_sil24 0000:06:06.0: version 1.1 [ 2.853794] scsi host0: sata_sil24 [ 2.853949] scsi host1: sata_sil24 [ 2.854075] scsi host2: sata_sil24 [ 2.854219] scsi host3: sata_sil24 [ 2.854311] ata1: SATA max UDMA/100 host m128@0xfdaff000 port 0xfdaf0000 irq 20 [ 2.854367] ata2: SATA max UDMA/100 host m128@0xfdaff000 port 0xfdaf2000 irq 20 [ 2.854424] ata3: SATA max UDMA/100 host m128@0xfdaff000 port 0xfdaf4000 irq 20 [ 2.854476] ata4: SATA max UDMA/100 host m128@0xfdaff000 port 0xfdaf6000 irq 20 [ 2.854598] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.854765] r8169 0000:06:0f.0 (unnamed net_device) (uninitialized): not PCI Express [ 2.855109] r8169 0000:06:0f.0 eth0: RTL8169sc/8110sc at 0xffffb7b900c91000, 00:1a:4d:9a:6d:99, XID 18000000 IRQ 23 [ 2.855161] r8169 0000:06:0f.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok] [ 2.859817] [drm] radeon kernel modesetting enabled. [ 2.861011] [drm] initializing kernel modesetting (VERDE 0x1002:0x6837 0x1787:0x2330 0x00). [ 2.861072] [drm] register mmio base: 0xFDD80000 [ 2.861137] [drm] register mmio size: 262144 [ 2.861243] radeon 0000:01:00.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0xffff [ 2.861696] ATOM BIOS: C44101 [ 2.861907] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used) [ 2.861957] radeon 0000:01:00.0: GTT: 2048M 0x0000000040000000 - 0x00000000BFFFFFFF [ 2.862013] [drm] Detected VRAM RAM=1024M, BAR=256M [ 2.862062] [drm] RAM width 128bits DDR [ 2.862177] [TTM] Zone kernel: Available graphics memory: 4089370 kiB [ 2.862225] [TTM] Zone dma32: Available graphics memory: 2097152 kiB [ 2.862270] [TTM] Initializing pool allocator [ 2.862322] [TTM] Initializing DMA pool allocator [ 2.862387] [drm] radeon: 1024M of VRAM memory ready [ 2.862431] [drm] radeon: 2048M of GTT memory ready. [ 2.862488] [drm] Loading verde Microcode [ 2.862554] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_pfp.bin [ 2.862615] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_me.bin [ 2.862680] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_ce.bin [ 2.862743] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_rlc.bin [ 2.862810] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_mc.bin [ 2.862887] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_smc.bin [ 2.862938] [drm] Internal thermal controller with fan control [ 2.863047] [drm] probing gen 2 caps for device 1002:7913 = 100d01/0 [ 2.865354] FDC 0 is a post-1991 82077 [ 2.869116] ehci-pci 0000:00:13.5: USB 2.0 started, EHCI 1.00 [ 2.869206] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.869255] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.869304] usb usb1: Product: EHCI Host Controller [ 2.869354] usb usb1: Manufacturer: Linux 4.9.2 ehci_hcd [ 2.869398] usb usb1: SerialNumber: 0000:00:13.5 [ 2.869583] hub 1-0:1.0: USB hub found [ 2.869642] hub 1-0:1.0: 10 ports detected [ 2.869912] ahci 0000:00:12.0: version 3.0 [ 2.870031] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit [ 2.870239] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode [ 2.870336] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part ccc [ 2.870605] ohci-pci: OHCI PCI platform driver [ 2.871068] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 2.871140] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 2 [ 2.871363] [drm] radeon: dpm initialized [ 2.871552] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/TAHITI_uvd.bin [ 2.871701] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/TAHITI_vce.bin [ 2.872466] [drm] Found VCE firmware/feedback version 50.0.1 / 17! [ 2.872575] [drm] GART: num cpu pages 524288, num gpu pages 524288 [ 2.872668] xhci_hcd 0000:04:00.0: hcc params 0x200071e1 hci version 0x100 quirks 0x00000010 [ 2.872925] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.872971] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.873025] usb usb2: Product: xHCI Host Controller [ 2.873073] usb usb2: Manufacturer: Linux 4.9.2 xhci-hcd [ 2.873148] usb usb2: SerialNumber: 0000:04:00.0 [ 2.873477] hub 2-0:1.0: USB hub found [ 2.873540] hub 2-0:1.0: 4 ports detected [ 2.873739] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 2.873792] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 [ 2.873862] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.873936] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 2.873984] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.874032] usb usb3: Product: xHCI Host Controller [ 2.874082] usb usb3: Manufacturer: Linux 4.9.2 xhci-hcd [ 2.874126] usb usb3: SerialNumber: 0000:04:00.0 [ 2.874700] hub 3-0:1.0: USB hub found [ 2.874871] hub 3-0:1.0: 4 ports detected [ 2.875504] [drm] probing gen 2 caps for device 1002:7913 = 100d01/0 [ 2.877835] scsi host4: ahci [ 2.881155] scsi host5: ahci [ 2.881376] scsi host6: ahci [ 2.881565] scsi host7: ahci [ 2.881715] ata5: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22 [ 2.881830] ata6: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22 [ 2.882625] r8169 0000:06:0f.0 enp6s15: renamed from eth0 [ 2.886417] ata7: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22 [ 2.886505] ata8: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22 [ 2.887587] scsi host8: pata_atiixp [ 2.887817] scsi host9: pata_atiixp [ 2.887949] ata9: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14 [ 2.888045] ata10: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15 [ 2.888168] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0 [ 2.888298] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb10 [ 2.888544] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 2.888683] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 4 [ 2.888842] ohci-pci 0000:00:13.0: irq 16, io mem 0xfe02e000 [ 2.894834] [drm] PCIE GART of 2048M enabled (table at 0x00000000001D6000). [ 2.894998] radeon 0000:01:00.0: WB enabled [ 2.895043] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff89b55f9b9c00 [ 2.895093] radeon 0000:01:00.0: fence driver on ring 1 use gpu addr 0x0000000040000c04 and cpu addr 0xffff89b55f9b9c04 [ 2.895142] radeon 0000:01:00.0: fence driver on ring 2 use gpu addr 0x0000000040000c08 and cpu addr 0xffff89b55f9b9c08 [ 2.895192] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff89b55f9b9c0c [ 2.895241] radeon 0000:01:00.0: fence driver on ring 4 use gpu addr 0x0000000040000c10 and cpu addr 0xffff89b55f9b9c10 [ 2.895741] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x0000000000075a18 and cpu addr 0xffffb7b901635a18 [ 2.915851] radeon 0000:01:00.0: fence driver on ring 6 use gpu addr 0x0000000040000c18 and cpu addr 0xffff89b55f9b9c18 [ 2.915901] radeon 0000:01:00.0: fence driver on ring 7 use gpu addr 0x0000000040000c1c and cpu addr 0xffff89b55f9b9c1c [ 2.915975] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.916026] [drm] Driver supports precise vblank timestamp query. [ 2.916073] radeon 0000:01:00.0: radeon: MSI limited to 32-bit [ 2.916162] radeon 0000:01:00.0: radeon: using MSI. [ 2.916239] [drm] radeon: irq initialized. [ 2.925180] firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0, physUB [ 2.953176] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.953240] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.953306] usb usb4: Product: OHCI PCI host controller [ 2.953367] usb usb4: Manufacturer: Linux 4.9.2 ohci_hcd [ 2.953428] usb usb4: SerialNumber: 0000:00:13.0 [ 2.953617] hub 4-0:1.0: USB hub found [ 2.953693] hub 4-0:1.0: 2 ports detected [ 2.953942] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 2.954007] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 5 [ 2.954109] ohci-pci 0000:00:13.1: irq 17, io mem 0xfe02d000 [ 2.985180] firewire_ohci 0000:06:0e.0: added OHCI v1.10 device as card 1, 4 IR + 8 IT contexts, quirks 0x2 [ 3.021177] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.021241] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.021307] usb usb5: Product: OHCI PCI host controller [ 3.021368] usb usb5: Manufacturer: Linux 4.9.2 ohci_hcd [ 3.021429] usb usb5: SerialNumber: 0000:00:13.1 [ 3.021613] hub 5-0:1.0: USB hub found [ 3.021689] hub 5-0:1.0: 2 ports detected [ 3.021943] ohci-pci 0000:00:13.2: OHCI PCI host controller [ 3.022008] ohci-pci 0000:00:13.2: new USB bus registered, assigned bus number 6 [ 3.022111] ohci-pci 0000:00:13.2: irq 18, io mem 0xfe02c000 [ 3.052125] ata9.00: ATAPI: ASUS DRW-1814BL, 1.14, max UDMA/66 [ 3.057341] ata9.00: configured for UDMA/66 [ 3.085182] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.085245] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.085311] usb usb6: Product: OHCI PCI host controller [ 3.085372] usb usb6: Manufacturer: Linux 4.9.2 ohci_hcd [ 3.085434] usb usb6: SerialNumber: 0000:00:13.2 [ 3.085623] hub 6-0:1.0: USB hub found [ 3.085702] hub 6-0:1.0: 2 ports detected [ 3.085954] ohci-pci 0000:00:13.3: OHCI PCI host controller [ 3.086020] ohci-pci 0000:00:13.3: new USB bus registered, assigned bus number 7 [ 3.086108] ohci-pci 0000:00:13.3: irq 17, io mem 0xfe02b000 [ 3.153163] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.153227] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.153292] usb usb7: Product: OHCI PCI host controller [ 3.153354] usb usb7: Manufacturer: Linux 4.9.2 ohci_hcd [ 3.153415] usb usb7: SerialNumber: 0000:00:13.3 [ 3.153583] hub 7-0:1.0: USB hub found [ 3.153659] hub 7-0:1.0: 2 ports detected [ 3.153885] ohci-pci 0000:00:13.4: OHCI PCI host controller [ 3.153949] ohci-pci 0000:00:13.4: new USB bus registered, assigned bus number 8 [ 3.154047] ohci-pci 0000:00:13.4: irq 18, io mem 0xfe02a000 [ 3.199705] ata8: SATA link down (SStatus 0 SControl 300) [ 3.205129] usb 1-1: new high-speed USB device number 2 using ehci-pci [ 3.217168] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.217231] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.217296] usb usb8: Product: OHCI PCI host controller [ 3.217357] usb usb8: Manufacturer: Linux 4.9.2 ohci_hcd [ 3.217418] usb usb8: SerialNumber: 0000:00:13.4 [ 3.217588] hub 8-0:1.0: USB hub found [ 3.217663] hub 8-0:1.0: 2 ports detected [ 3.361131] ata7: softreset failed (device not ready) [ 3.361196] ata7: applying PMP SRST workaround and retrying [ 3.377529] usb 1-1: New USB device found, idVendor=03f0, idProduct=0610 [ 3.377592] usb 1-1: New USB device strings: Mfr=10, Product=11, SerialNumber=0 [ 3.377658] usb 1-1: Product: USB2.0 HUB [ 3.377718] usb 1-1: Manufacturer: Genesyslogic [ 3.378171] hub 1-1:1.0: USB hub found [ 3.379915] hub 1-1:1.0: 4 ports detected [ 3.437206] firewire_core 0000:05:00.0: created device fw0: GUID 00309300000001c3, S800 [ 3.441187] tsc: Refined TSC clocksource calibration: 3207.272 MHz [ 3.441259] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2e3b1f431f7, max_idle_ns: 440795241363 ns [ 3.501195] firewire_core 0000:06:0e.0: created device fw1: GUID 001a4d0000eb2917, S400 [ 3.503056] [drm] ring test on 0 succeeded in 1 usecs [ 3.503107] [drm] ring test on 1 succeeded in 1 usecs [ 3.503154] [drm] ring test on 2 succeeded in 1 usecs [ 3.503212] [drm] ring test on 3 succeeded in 10 usecs [ 3.503267] [drm] ring test on 4 succeeded in 10 usecs [ 3.521140] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.521313] ata7.00: ATA-8: OCZ-VECTOR180, 1.01, max UDMA/133 [ 3.521360] ata7.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 31/32), AA [ 3.521406] ata7.00: SB600 AHCI: limiting to 255 sectors per cmd [ 3.522443] ata7.00: SB600 AHCI: limiting to 255 sectors per cmd [ 3.522490] ata7.00: configured for UDMA/133 [ 3.573130] ata5: softreset failed (device not ready) [ 3.573177] ata5: applying PMP SRST workaround and retrying [ 3.573240] ata6: softreset failed (device not ready) [ 3.573287] ata6: applying PMP SRST workaround and retrying [ 3.679100] [drm] ring test on 5 succeeded in 1 usecs [ 3.679151] [drm] UVD initialized successfully. [ 3.733138] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.733210] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.734479] ata6.00: HPA detected: current 3907020911, native 3907029168 [ 3.734631] ata6.00: ATA-8: Hitachi HDS5C3020ALA632, ML6OA580, max UDMA/133 [ 3.734676] ata6.00: 3907020911 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 3.734725] ata6.00: SB600 AHCI: limiting to 255 sectors per cmd [ 3.736209] ata6.00: SB600 AHCI: limiting to 255 sectors per cmd [ 3.736255] ata6.00: configured for UDMA/133 [ 3.737122] usb 1-1.1: new full-speed USB device number 4 using ehci-pci [ 3.738726] ata5.00: ATA-8: WDC WD10EARS-00MVWB0, 51.0AB51, max UDMA/133 [ 3.738773] ata5.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 3.738822] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd [ 3.743261] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd [ 3.743307] ata5.00: configured for UDMA/133 [ 3.788406] [drm] ring test on 6 succeeded in 18 usecs [ 3.788465] [drm] ring test on 7 succeeded in 4 usecs [ 3.788508] [drm] VCE initialized successfully. [ 3.788655] [drm] ib test on ring 0 succeeded in 0 usecs [ 3.788731] [drm] ib test on ring 1 succeeded in 0 usecs [ 3.788804] [drm] ib test on ring 2 succeeded in 0 usecs [ 3.788892] [drm] ib test on ring 3 succeeded in 0 usecs [ 3.788978] [drm] ib test on ring 4 succeeded in 0 usecs [ 3.857720] usb 1-1.1: New USB device found, idVendor=046d, idProduct=c042 [ 3.857767] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.857815] usb 1-1.1: Product: USB Gaming Mouse [ 3.857859] usb 1-1.1: Manufacturer: Logitech [ 3.860923] hidraw: raw HID events driver (C) Jiri Kosina [ 3.870963] usbcore: registered new interface driver usbhid [ 3.871010] usbhid: USB HID core driver [ 3.871666] input: Logitech USB Gaming Mouse as /devices/pci0000:00/0000:00:13.5/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C042.0001/input/input1 [ 3.871798] hid-generic 0003:046D:C042.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:13.5-1.1/input0 [ 3.872818] hid-generic 0003:046D:C042.0002: hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:13.5-1.1/input1 [ 3.965137] usb 7-1: new full-speed USB device number 2 using ohci-pci [ 3.965139] usb 1-8: new high-speed USB device number 5 using ehci-pci [ 4.117522] usb 1-8: New USB device found, idVendor=05e3, idProduct=070e [ 4.117569] usb 1-8: New USB device strings: Mfr=3, Product=4, SerialNumber=5 [ 4.120169] usb 1-8: Product: USB Reader [ 4.120213] usb 1-8: Manufacturer: Genesys [ 4.120256] usb 1-8: SerialNumber: 000000590523 [ 4.122861] usb-storage 1-8:1.0: USB Mass Storage device detected [ 4.123056] scsi host10: usb-storage 1-8:1.0 [ 4.123169] usbcore: registered new interface driver usb-storage [ 4.123509] usbcore: registered new interface driver uas [ 4.164139] usb 7-1: New USB device found, idVendor=0a5c, idProduct=21e8 [ 4.164186] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.164231] usb 7-1: Product: BCM920702 Bluetooth 4.0 [ 4.164274] usb 7-1: Manufacturer: Broadcom Corp [ 4.164318] usb 7-1: SerialNumber: 5CF3707BF326 [ 4.193124] usb 1-1.2: new low-speed USB device number 6 using ehci-pci [ 4.321298] usb 1-1.2: New USB device found, idVendor=04d9, idProduct=1603 [ 4.321345] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.321393] usb 1-1.2: Product: USB Keyboard [ 4.321436] usb 1-1.2: Manufacturer: [ 4.331906] input: USB Keyboard as /devices/pci0000:00/0000:00:13.5/usb1/1-1/1-1.2/1-1.2:1.0/0003:04D9:1603.0003/input/input2 [ 4.389252] hid-generic 0003:04D9:1603.0003: input,hidraw2: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:13.5-1.2/input0 [ 4.406353] input: USB Keyboard as /devices/pci0000:00/0000:00:13.5/usb1/1-1/1-1.2/1-1.2:1.1/0003:04D9:1603.0004/input/input3 [ 4.421128] usb 1-9: new high-speed USB device number 7 using ehci-pci [ 4.461159] [drm] ib test on ring 5 succeeded [ 4.461229] clocksource: Switched to clocksource tsc [ 4.465165] hid-generic 0003:04D9:1603.0004: input,hidraw3: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:13.5-1.2/input1 [ 4.572950] usb 1-9: New USB device found, idVendor=05e3, idProduct=0716 [ 4.572997] usb 1-9: New USB device strings: Mfr=0, Product=1, SerialNumber=2 [ 4.573041] usb 1-9: Product: USB Storage [ 4.573085] usb 1-9: SerialNumber: 000000009744 [ 4.573726] usb-storage 1-9:1.0: USB Mass Storage device detected [ 4.573859] scsi host11: usb-storage 1-9:1.0 [ 4.917131] ata1: SATA link down (SStatus 0 SControl 0) [ 4.973141] [drm] ib test on ring 6 succeeded [ 5.134285] scsi 10:0:0:0: Direct-Access Generic STORAGE DEVICE 9325 PQ: 0 ANSI: 0 [ 5.135161] scsi 10:0:0:1: Direct-Access Generic STORAGE DEVICE 9325 PQ: 0 ANSI: 0 [ 5.139120] random: fast init done [ 5.139389] sd 10:0:0:0: [sda] Attached SCSI removable disk [ 5.140013] sd 10:0:0:1: [sdb] Attached SCSI removable disk [ 5.485144] [drm] ib test on ring 7 succeeded [ 5.485219] [drm] hw_i2c forced on, you may experience display detection problems! [ 5.485507] [drm] forcing HDMI-A-1 connector OFF [ 5.485598] [drm] forcing DVI-D-1 connector ON [ 5.485676] [drm] forcing VGA-1 connector OFF [ 5.485743] [drm] Radeon Display Connectors [ 5.485786] [drm] Connector 0: [ 5.485829] [drm] HDMI-A-1 [ 5.485871] [drm] HPD1 [ 5.485914] [drm] DDC: 0x6570 0x6570 0x6574 0x6574 0x6578 0x6578 0x657c 0x657c [ 5.485962] [drm] Encoders: [ 5.486004] [drm] DFP1: INTERNAL_UNIPHY2 [ 5.486047] [drm] Connector 1: [ 5.486089] [drm] DVI-D-1 [ 5.486132] [drm] HPD2 [ 5.486175] [drm] DDC: 0x6560 0x6560 0x6564 0x6564 0x6568 0x6568 0x656c 0x656c [ 5.486222] [drm] Encoders: [ 5.486265] [drm] DFP2: INTERNAL_UNIPHY [ 5.486307] [drm] Connector 2: [ 5.486350] [drm] VGA-1 [ 5.486392] [drm] DDC: 0x6540 0x6540 0x6544 0x6544 0x6548 0x6548 0x654c 0x654c [ 5.486440] [drm] Encoders: [ 5.486482] [drm] CRT1: INTERNAL_KLDSCP_DAC1 [ 5.517096] [drm] fb mappable at 0xD05D9000 [ 5.517139] [drm] vram apper at 0xD0000000 [ 5.517182] [drm] size 2457600 [ 5.517225] [drm] fb depth is 8 [ 5.517267] [drm] pitch is 2048 [ 5.517376] fbcon: radeondrmfb (fb0) is primary device [ 5.572944] Console: switching to colour frame buffer device 240x75 [ 5.574467] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device [ 5.582461] scsi 11:0:0:0: Direct-Access Generic STORAGE DEVICE 9744 PQ: 0 ANSI: 0 [ 5.583336] scsi 11:0:0:1: Direct-Access Generic STORAGE DEVICE 9744 PQ: 0 ANSI: 0 [ 5.591698] sd 11:0:0:0: [sdc] Attached SCSI removable disk [ 5.592329] sd 11:0:0:1: [sdd] Attached SCSI removable disk [ 5.593474] [drm] Initialized radeon 2.48.0 20080528 for 0000:01:00.0 on minor 0 [ 7.097288] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 7.098176] ata2.00: HPA detected: current 312579695, native 312581808 [ 7.098195] ata2.00: ATA-7: Hitachi HDS721616PLA380, P22OABEA, max UDMA/133 [ 7.098205] ata2.00: 312579695 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 7.099255] ata2.00: configured for UDMA/100 [ 7.099452] scsi 1:0:0:0: Direct-Access ATA Hitachi HDS72161 ABEA PQ: 0 ANSI: 5 [ 7.129293] sd 1:0:0:0: [sde] 312579695 512-byte logical blocks: (160 GB/149 GiB) [ 7.129411] sd 1:0:0:0: [sde] Write Protect is off [ 7.129424] sd 1:0:0:0: [sde] Mode Sense: 00 3a 00 00 [ 7.129453] sd 1:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.151580] sd 1:0:0:0: [sde] Attached SCSI disk [ 9.309288] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 9.310172] ata3.00: HPA detected: current 312579695, native 312581808 [ 9.310187] ata3.00: ATA-7: Hitachi HDS721616PLA380, P22OABEA, max UDMA/133 [ 9.310197] ata3.00: 312579695 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 9.311246] ata3.00: configured for UDMA/100 [ 9.311422] scsi 2:0:0:0: Direct-Access ATA Hitachi HDS72161 ABEA PQ: 0 ANSI: 5 [ 9.341303] sd 2:0:0:0: [sdf] 312579695 512-byte logical blocks: (160 GB/149 GiB) [ 9.341403] sd 2:0:0:0: [sdf] Write Protect is off [ 9.341416] sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00 [ 9.341446] sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.369882] sd 2:0:0:0: [sdf] Attached SCSI disk [ 11.393137] ata4: SATA link down (SStatus 0 SControl 0) [ 11.393334] scsi 4:0:0:0: Direct-Access ATA WDC WD10EARS-00M AB51 PQ: 0 ANSI: 5 [ 11.425292] sd 4:0:0:0: [sdg] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 11.425307] sd 4:0:0:0: [sdg] 4096-byte physical blocks [ 11.425410] sd 4:0:0:0: [sdg] Write Protect is off [ 11.425422] sd 4:0:0:0: [sdg] Mode Sense: 00 3a 00 00 [ 11.425438] scsi 5:0:0:0: Direct-Access ATA Hitachi HDS5C302 A580 PQ: 0 ANSI: 5 [ 11.425449] sd 4:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.442088] sdg: sdg1 sdg2 sdg3 [ 11.442481] sd 4:0:0:0: [sdg] Attached SCSI disk [ 11.457273] sd 5:0:0:0: [sdh] 3907020911 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 11.457368] sd 5:0:0:0: [sdh] Write Protect is off [ 11.457380] sd 5:0:0:0: [sdh] Mode Sense: 00 3a 00 00 [ 11.457399] scsi 6:0:0:0: Direct-Access ATA OCZ-VECTOR180 1.01 PQ: 0 ANSI: 5 [ 11.457409] sd 5:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.489283] sd 6:0:0:0: [sdi] 234441648 512-byte logical blocks: (120 GB/112 GiB) [ 11.489407] sd 6:0:0:0: [sdi] Write Protect is off [ 11.489419] sd 6:0:0:0: [sdi] Mode Sense: 00 3a 00 00 [ 11.489444] sd 6:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.489892] scsi 8:0:0:0: CD-ROM ASUS DRW-1814BL 1.14 PQ: 0 ANSI: 5 [ 11.490207] sdi: sdi1 sdi2 [ 11.490561] sd 6:0:0:0: [sdi] Attached SCSI disk [ 11.498525] sdh: sdh1 sdh2 sdh3 sdh4 [ 11.498932] sd 5:0:0:0: [sdh] Attached SCSI disk [ 11.519205] sr 8:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 11.519226] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 11.519942] sr 8:0:0:0: Attached scsi CD-ROM sr0 [ 11.524854] md: bind<sdi2> [ 11.568599] device-mapper: uevent: version 1.0.3 [ 11.569257] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 11.570959] bcache: bch_journal_replay() journal replay done, 222 keys in 18 entries, seq 277165 [ 11.572529] bcache: register_cache() registered cache device sdi1 [ 11.665956] md: bind<sdg2> [ 11.667876] md: raid1 personality registered for level 1 [ 11.668677] md/raid1:md127: active with 2 out of 2 mirrors [ 11.669393] created bitmap (1 pages) for device md127 [ 11.670063] md127: bitmap initialized from disk: read 1 pages, set 0 of 1724 bits [ 11.736285] md127: detected capacity change from 0 to 115670974464 [ 11.737148] md127: p1 p2 p3 [ 11.757297] bcache: register_bdev() registered backing device sdg1 [ 11.799462] bcache: bch_cached_dev_attach() Caching sdg1 as bcache0 on set 83bdeae1-6390-4435-ae29-c31616227bc7 [ 11.977678] random: crng init done [ 12.452269] md: linear personality registered for level -1 [ 12.454108] md: multipath personality registered for level -4 [ 12.456055] md: raid0 personality registered for level 0 [ 12.569125] raid6: sse2x1 gen() 3834 MB/s [ 12.637114] raid6: sse2x1 xor() 4277 MB/s [ 12.705118] raid6: sse2x2 gen() 6483 MB/s [ 12.773113] raid6: sse2x2 xor() 7282 MB/s [ 12.841126] raid6: sse2x4 gen() 6869 MB/s [ 12.909114] raid6: sse2x4 xor() 4560 MB/s [ 12.909704] raid6: using algorithm sse2x4 gen() 6869 MB/s [ 12.910293] raid6: .... xor() 4560 MB/s, rmw enabled [ 12.910879] raid6: using intx1 recovery algorithm [ 12.911670] xor: measuring software checksum speed [ 12.949118] prefetch64-sse: 12256.000 MB/sec [ 12.989118] generic_sse: 11646.000 MB/sec [ 12.989702] xor: using function: prefetch64-sse (12256.000 MB/sec) [ 12.990524] async_tx: api initialized (async) [ 12.992379] md: raid6 personality registered for level 6 [ 12.993048] md: raid5 personality registered for level 5 [ 12.993642] md: raid4 personality registered for level 4 [ 12.997315] md: raid10 personality registered for level 10 [ 13.296939] Btrfs loaded, crc32c=crc32c-generic [ 13.381140] blk_update_request: I/O error, dev fd0, sector 0 [ 13.381735] floppy: error -5 while reading block 0 [ 13.969467] BTRFS: device label home devid 1 transid 3289 /dev/md127p3 [ 13.970161] BTRFS: device label srv devid 2 transid 174 /dev/sdh3 [ 13.970845] BTRFS: device label srv devid 1 transid 174 /dev/sdg3 [ 13.973330] PM: Starting manual resume from disk [ 13.973900] PM: Hibernation image partition 8:113 present [ 13.973901] PM: Looking for hibernation image. [ 13.974044] PM: Image not found (code -22) [ 13.974045] PM: Hibernation image not present or could not be loaded. [ 14.106664] EXT4-fs (md127p2): mounted filesystem with ordered data mode. Opts: (null) [ 14.218213] ip_tables: (C) 2000-2006 Netfilter Core Team [ 14.222074] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 14.222750] systemd[1]: Detected architecture x86-64. [ 14.225414] systemd[1]: Set hostname to <c21>. [ 14.286478] systemd[1]: Listening on Journal Socket. [ 14.287772] systemd[1]: Listening on udev Control Socket. [ 14.289009] systemd[1]: Listening on Journal Audit Socket. [ 14.290299] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 14.291525] systemd[1]: Listening on Journal Socket (/dev/log). [ 14.292753] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 14.294089] systemd[1]: Created slice System Slice. [ 14.306823] it87: Found IT8716F chip at 0x228, revision 0 [ 14.306844] it87: Beeping is supported [ 14.316148] EXT4-fs (md127p2): re-mounted. Opts: errors=remount-ro [ 14.402136] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4 [ 14.402714] ACPI: Power Button [PWRB] [ 14.403335] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5 [ 14.403916] ACPI: Power Button [PWRF] [ 14.408675] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP] [ 14.410139] acpi_cpufreq: overriding BIOS provided _PSD data [ 14.416712] sd 10:0:0:0: Attached scsi generic sg0 type 0 [ 14.417708] sd 10:0:0:1: Attached scsi generic sg1 type 0 [ 14.418316] sd 11:0:0:0: Attached scsi generic sg2 type 0 [ 14.418928] sd 11:0:0:1: Attached scsi generic sg3 type 0 [ 14.419589] sd 1:0:0:0: Attached scsi generic sg4 type 0 [ 14.420408] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 14.421028] sd 2:0:0:0: Attached scsi generic sg5 type 0 [ 14.422592] sd 4:0:0:0: Attached scsi generic sg6 type 0 [ 14.423740] sd 5:0:0:0: Attached scsi generic sg7 type 0 [ 14.424411] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05 [ 14.424697] sd 6:0:0:0: Attached scsi generic sg8 type 0 [ 14.424748] sr 8:0:0:0: Attached scsi generic sg9 type 5 [ 14.426300] sp5100_tco: PCI Vendor ID: 0x1002, Device ID: 0x4385, Revision ID: 0x14 [ 14.426871] sp5100_tco: failed to find MMIO address, giving up. [ 14.459472] snd_hda_intel 0000:00:14.2: position_fix set to 1 for device 1458:a022 [ 14.460455] snd_hda_intel: probe of 0000:01:00.1 failed with error -2 [ 14.485265] snd_hda_codec_realtek hdaudioC0D3: autoconfig for ALC889A: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line [ 14.485838] snd_hda_codec_realtek hdaudioC0D3: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 14.486396] snd_hda_codec_realtek hdaudioC0D3: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0) [ 14.486922] snd_hda_codec_realtek hdaudioC0D3: mono: mono_out=0x0 [ 14.487439] snd_hda_codec_realtek hdaudioC0D3: dig-out=0x1e/0x0 [ 14.487941] snd_hda_codec_realtek hdaudioC0D3: inputs: [ 14.488439] snd_hda_codec_realtek hdaudioC0D3: Rear Mic=0x18 [ 14.488949] snd_hda_codec_realtek hdaudioC0D3: Front Mic=0x19 [ 14.489466] snd_hda_codec_realtek hdaudioC0D3: Line=0x1a [ 14.489991] snd_hda_codec_realtek hdaudioC0D3: CD=0x1c [ 14.490177] snd_ice1712 0000:06:07.0: Using board model TerraTec DMX6Fire [ 14.490985] snd_hda_codec_realtek hdaudioC0D3: dig-in=0x1f [ 14.507492] Bluetooth: Core ver 2.22 [ 14.508013] NET: Registered protocol family 31 [ 14.508493] Bluetooth: HCI device and connection manager initialized [ 14.508968] Bluetooth: HCI socket layer initialized [ 14.511338] Bluetooth: L2CAP socket layer initialized [ 14.512165] Bluetooth: SCO socket layer initialized [ 14.517683] input: PC Speaker as /devices/platform/pcspkr/input/input6 [ 14.521043] usbcore: registered new interface driver btusb [ 14.530275] Bluetooth: hci0: BCM: chip id 63 [ 14.531835] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7 [ 14.533937] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input8 [ 14.534503] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input9 [ 14.535073] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input10 [ 14.535638] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input11 [ 14.536246] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input12 [ 14.536800] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input13 [ 14.538790] bcache: register_bcache() error opening /dev/sdg1: device already registered [ 14.549307] Bluetooth: hci0: c21 [ 14.551373] Bluetooth: hci0: BCM20702A1 (001.002.014) build 1338 [ 14.552780] bluetooth hci0: firmware: direct-loading firmware brcm/BCM20702A1-0a5c-21e8.hcd [ 14.554066] kvm: Nested Virtualization enabled [ 14.554590] kvm: Nested Paging enabled [ 14.557603] EDAC MC: Ver: 3.0.0 [ 14.558989] bcache: register_bcache() error opening /dev/sdi1: device already registered [ 14.560914] MCE: In-kernel MCE decoding enabled. [ 14.562535] EDAC amd64: DRAM ECC disabled. [ 14.563040] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load. Either enable ECC checking or force module loading by setting 'ecc_enable_override'. (Note that use of the override may cause unknown side effects.) [ 14.602687] ppdev: user-space parallel port driver [ 14.603346] EDAC amd64: DRAM ECC disabled. [ 14.603997] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load. Either enable ECC checking or force module loading by setting 'ecc_enable_override'. (Note that use of the override may cause unknown side effects.) [ 15.188907] Adding 16777212k swap on /dev/sdh1. Priority:-1 extents:1 across:16777212k FS [ 15.347208] Bluetooth: hci0: BCM20702A1 (001.002.014) build 1338 [ 15.366194] Bluetooth: hci0: Broadcom Bluetooth Device [ 15.389882] BTRFS info (device md127p3): use ssd allocation scheme [ 15.390704] BTRFS info (device md127p3): use lzo compression [ 15.390706] BTRFS info (device md127p3): disk space caching is enabled [ 15.390707] BTRFS info (device md127p3): has skinny extents [ 15.431388] EXT4-fs (bcache0): mounted filesystem with ordered data mode. Opts: (null) [ 15.455247] systemd-journald[423]: Received request to flush runtime journal from PID 1 [ 15.456994] EXT4-fs (md127p1): mounted filesystem with ordered data mode. Opts: (null) [ 15.549810] BTRFS info (device sdg3): disk space caching is enabled [ 15.551856] BTRFS info (device sdg3): has skinny extents [ 15.673919] EXT4-fs (sdh2): mounted filesystem without journal. Opts: (null) [ 15.715252] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 15.756160] XFS (sdh4): Mounting V5 Filesystem [ 15.887668] XFS (sdh4): Ending clean mount [ 15.933906] r8169 0000:06:0f.0 enp6s15: link down [ 15.935936] r8169 0000:06:0f.0 enp6s15: link down [ 15.938010] IPv6: ADDRCONF(NETDEV_UP): enp6s15: link is not ready [ 16.135146] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 16.135148] Bluetooth: BNEP filters: protocol multicast [ 16.135156] Bluetooth: BNEP socket layer initialized [ 19.335519] r8169 0000:06:0f.0 enp6s15: link up [ 19.337439] IPv6: ADDRCONF(NETDEV_CHANGE): enp6s15: link becomes ready [ 266.470363] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen [ 266.472190] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data [ 266.474022] ata2.00: failed command: READ FPDMA QUEUED [ 266.475827] ata2.00: cmd 60/00:00:f0:bb:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in res 60/00:00:f0:bb:0e/00:00:00:00:00/40 Emask 0x21 (host bus error) [ 266.479401] ata2.00: status: { DRDY DF } [ 266.481180] ata2.00: failed command: READ FPDMA QUEUED [ 266.482964] ata2.00: cmd 60/00:08:f0:ba:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in res 40/25:02:02:00:00/00:00:40:10:40/00 Emask 0x20 (host bus error) [ 266.486912] ata2.00: status: { DRDY } [ 266.488711] ata2.00: error: { AMNF ABRT } [ 266.490524] ata2: hard resetting link [ 266.492295] ata2: controller in dubious state, performing PORT_RST [ 268.693624] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 268.697455] ata2.00: configured for UDMA/100 [ 268.699297] ata2: EH complete [ 268.834440] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen [ 268.836245] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data [ 268.838063] ata2.00: failed command: READ FPDMA QUEUED [ 268.839843] ata2.00: cmd 60/00:00:f0:ba:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in res 40/25:02:02:00:00/00:00:40:00:40/00 Emask 0x20 (host bus error) [ 268.843421] ata2.00: status: { DRDY } [ 268.845213] ata2.00: error: { AMNF ABRT } [ 268.847013] ata2.00: failed command: READ FPDMA QUEUED [ 268.848794] ata2.00: cmd 60/00:08:f0:bb:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error) [ 268.852416] ata2.00: status: { DRDY } [ 268.854236] ata2.00: error: { AMNF ABRT } [ 268.856027] ata2: hard resetting link [ 268.857801] ata2: controller in dubious state, performing PORT_RST [ 271.057626] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 271.061485] ata2.00: configured for UDMA/100 [ 271.063319] ata2: EH complete [ 271.202443] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen [ 271.204249] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data [ 271.206073] ata2.00: failed command: READ FPDMA QUEUED [ 271.207870] ata2.00: cmd 60/00:00:f0:bb:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in res 40/25:02:02:00:00/00:00:00:00:40/00 Emask 0x20 (host bus error) [ 271.211530] ata2.00: status: { DRDY } [ 271.213363] ata2.00: error: { AMNF ABRT } [ 271.215189] ata2.00: failed command: READ FPDMA QUEUED [ 271.217016] ata2.00: cmd 60/00:08:f0:ba:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error) [ 271.220715] ata2.00: status: { DRDY } [ 271.222581] ata2.00: error: { AMNF ABRT } [ 271.224427] ata2: hard resetting link [ 271.226281] ata2: controller in dubious state, performing PORT_RST [ 273.425629] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 273.429528] ata2.00: configured for UDMA/100 [ 273.431416] ata2: EH complete [ 273.566425] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen [ 273.568314] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data [ 273.570224] ata2.00: failed command: READ FPDMA QUEUED [ 273.572099] ata2.00: cmd 60/00:00:f0:ba:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in res 40/25:02:02:00:00/00:00:40:00:40/00 Emask 0x20 (host bus error) [ 273.575879] ata2.00: status: { DRDY } [ 273.577806] ata2.00: error: { AMNF ABRT } [ 273.580071] ata2.00: failed command: READ FPDMA QUEUED [ 273.581984] ata2.00: cmd 60/00:08:f0:bb:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error) [ 273.585815] ata2.00: status: { DRDY } [ 273.587706] ata2.00: error: { AMNF ABRT } [ 273.589596] ata2: hard resetting link [ 273.591468] ata2: controller in dubious state, performing PORT_RST [ 275.793629] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 275.797567] ata2.00: configured for UDMA/100 [ 275.799496] ata2: EH complete [ 275.934436] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen [ 275.936386] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data [ 275.938361] ata2.00: failed command: READ FPDMA QUEUED [ 275.940330] ata2.00: cmd 60/00:00:f0:bb:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in res 40/25:02:02:00:00/00:00:00:00:40/00 Emask 0x20 (host bus error) [ 275.944329] ata2.00: status: { DRDY } [ 275.946355] ata2.00: error: { AMNF ABRT } [ 275.948346] ata2.00: failed command: READ FPDMA QUEUED [ 275.950347] ata2.00: cmd 60/00:08:f0:ba:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error) [ 275.954345] ata2.00: status: { DRDY } [ 275.956330] ata2.00: error: { AMNF ABRT } [ 275.958324] ata2: hard resetting link [ 275.960284] ata2: controller in dubious state, performing PORT_RST [ 278.161633] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 278.165627] ata2.00: configured for UDMA/100 [ 278.167609] ata2: EH complete [ 278.310432] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen [ 278.312407] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data [ 278.314397] ata2.00: failed command: READ FPDMA QUEUED [ 278.316365] ata2.00: cmd 60/00:00:f0:ba:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in res 40/25:02:02:00:00/00:00:40:00:40/00 Emask 0x20 (host bus error) [ 278.320315] ata2.00: status: { DRDY } [ 278.322304] ata2.00: error: { AMNF ABRT } [ 278.324279] ata2.00: failed command: READ FPDMA QUEUED [ 278.326268] ata2.00: cmd 60/00:08:f0:bb:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error) [ 278.330242] ata2.00: status: { DRDY } [ 278.332212] ata2.00: error: { AMNF ABRT } [ 278.334178] ata2: hard resetting link [ 278.336128] ata2: controller in dubious state, performing PORT_RST [ 280.537636] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 280.541646] ata2.00: configured for UDMA/100 [ 280.543627] sd 1:0:0:0: [sde] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 280.545611] sd 1:0:0:0: [sde] tag#0 Sense Key : Medium Error [current] [ 280.547567] sd 1:0:0:0: [sde] tag#0 Add. Sense: Address mark not found for data field [ 280.549548] sd 1:0:0:0: [sde] tag#0 CDB: Read(10) 28 00 00 0e ba f0 00 01 00 00 [ 280.551517] blk_update_request: I/O error, dev sde, sector 965360 [ 280.553542] sd 1:0:0:0: [sde] tag#1 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 280.555901] sd 1:0:0:0: [sde] tag#1 Sense Key : Medium Error [current] [ 280.557924] sd 1:0:0:0: [sde] tag#1 Add. Sense: Address mark not found for data field [ 280.559928] sd 1:0:0:0: [sde] tag#1 CDB: Read(10) 28 00 00 0e bb f0 00 01 00 00 [ 280.561940] blk_update_request: I/O error, dev sde, sector 965616 [ 280.563961] ata2: EH complete [ 8348.620026] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen [ 8348.621645] ata1: irq_stat 0x00b40090, PHY RDY changed [ 8348.623295] ata1: hard resetting link [ 8358.626310] ata1: softreset failed (timeout) [ 8358.627924] ata1: hard resetting link [ 8361.391599] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 8361.393811] ata1.00: ATA-8: ST3000DM001-9YN166, CC4H, max UDMA/133 [ 8361.395466] ata1.00: 5860533168 sectors, multi 0: LBA48 [ 8361.397671] ata1.00: configured for UDMA/100 [ 8361.398342] ata1: EH complete [ 8361.399205] scsi 0:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC4H PQ: 0 ANSI: 5 [ 8361.438676] sd 0:0:0:0: Attached scsi generic sg10 type 0 [ 8361.438689] sd 0:0:0:0: [sdj] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 8361.438694] sd 0:0:0:0: [sdj] 4096-byte physical blocks [ 8361.438888] sd 0:0:0:0: [sdj] Write Protect is off [ 8361.438896] sd 0:0:0:0: [sdj] Mode Sense: 00 3a 00 00 [ 8361.438971] sd 0:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8361.487871] sdj: sdj1 sdj2 [ 8361.489045] sd 0:0:0:0: [sdj] Attached SCSI disk [10562.688262] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10562.689701] ata1.00: irq_stat 0x00060002, PCI master abort while transferring data [10562.691127] ata1.00: failed command: READ DMA [10562.692609] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10562.695565] ata1.00: status: { Busy } [10562.697060] ata1: hard resetting link [10562.698547] ata1: controller in dubious state, performing PORT_RST [10564.889203] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [10564.891970] ata1.00: configured for UDMA/100 [10564.893545] ata1: EH complete [10565.028037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10565.029608] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10565.031207] ata1.00: failed command: READ DMA [10565.032784] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10565.035952] ata1.00: status: { Busy } [10565.037543] ata1: hard resetting link [10565.039140] ata1: controller in dubious state, performing PORT_RST [10567.228972] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [10567.231793] ata1.00: configured for UDMA/100 [10567.233456] ata1: EH complete [10567.368096] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10567.369692] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10567.371315] ata1.00: failed command: READ DMA [10567.372995] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10567.376224] ata1.00: status: { Busy } [10567.377851] ata1: hard resetting link [10567.379492] ata1: controller in dubious state, performing PORT_RST [10569.568810] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [10569.571690] ata1.00: configured for UDMA/100 [10569.573371] ata1: EH complete [10569.707698] ata1: limiting SATA link speed to 1.5 Gbps [10569.709374] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10569.711087] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10569.712777] ata1.00: failed command: READ DMA [10569.714466] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10569.717913] ata1.00: status: { Busy } [10569.719683] ata1: hard resetting link [10569.721770] ata1: controller in dubious state, performing PORT_RST [10571.912619] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10) [10571.915665] ata1.00: configured for UDMA/100 [10571.917481] ata1: EH complete [10572.051552] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10572.053372] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10572.055229] ata1.00: failed command: READ DMA [10572.057046] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10572.060734] ata1.00: status: { Busy } [10572.062609] ata1: hard resetting link [10572.064484] ata1: controller in dubious state, performing PORT_RST [10574.257205] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10) [10574.260335] ata1.00: configured for UDMA/100 [10574.262294] ata1: EH complete [10574.399322] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10574.401276] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10574.403257] ata1.00: failed command: READ DMA [10574.405205] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10574.409144] ata1.00: status: { Busy } [10574.411542] ata1: hard resetting link [10574.413555] ata1: controller in dubious state, performing PORT_RST [10576.604232] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10) [10576.607520] ata1.00: configured for UDMA/100 [10576.609563] sd 0:0:0:0: [sdj] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [10576.611611] sd 0:0:0:0: [sdj] tag#0 Sense Key : Aborted Command [current] [10576.613654] sd 0:0:0:0: [sdj] tag#0 Add. Sense: Scsi parity error [10576.616047] sd 0:0:0:0: [sdj] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 d3 d3 e0 00 00 01 00 00 00 [10576.618148] blk_update_request: I/O error, dev sdj, sector 13882336 [10576.620285] ata1: EH complete [10576.759123] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10576.761194] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10576.763277] ata1.00: failed command: READ DMA [10576.765334] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10576.769458] ata1.00: status: { Busy } [10576.771537] ata1: hard resetting link [10576.773567] ata1: controller in dubious state, performing PORT_RST [10578.964029] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10) [10578.967309] ata1.00: configured for UDMA/100 [10578.969352] ata1: EH complete [10579.102837] ata1.00: limiting speed to UDMA/66:PIO4 [10579.104858] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10579.106911] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10579.108930] ata1.00: failed command: READ DMA [10579.110962] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10579.115015] ata1.00: status: { Busy } [10579.117024] ata1: hard resetting link [10579.119025] ata1: controller in dubious state, performing PORT_RST [10581.307818] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10) [10581.311119] ata1.00: configured for UDMA/66 [10581.313168] ata1: EH complete [10581.450700] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10581.452739] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10581.454797] ata1.00: failed command: READ DMA [10581.456811] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10581.460858] ata1.00: status: { Busy } [10581.462922] ata1: hard resetting link [10581.464926] ata1: controller in dubious state, performing PORT_RST [10583.655637] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10) [10583.658911] ata1.00: configured for UDMA/66 [10583.660997] ata1: EH complete [10583.794492] ata1.00: limiting speed to UDMA/33:PIO4 [10583.796511] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10583.798564] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10583.800583] ata1.00: failed command: READ DMA [10583.802618] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10583.806679] ata1.00: status: { Busy } [10583.809058] ata1: hard resetting link [10583.811090] ata1: controller in dubious state, performing PORT_RST [10585.999405] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10) [10586.002714] ata1.00: configured for UDMA/33 [10586.004761] ata1: EH complete [10586.142263] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10586.144308] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10586.146368] ata1.00: failed command: READ DMA [10586.148404] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10586.152495] ata1.00: status: { Busy } [10586.154561] ata1: hard resetting link [10586.156566] ata1: controller in dubious state, performing PORT_RST [10588.347248] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10) [10588.350519] ata1.00: configured for UDMA/33 [10588.352550] ata1: EH complete [10588.494107] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [10588.496144] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data [10588.498202] ata1.00: failed command: READ DMA [10588.500218] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error) [10588.504272] ata1.00: status: { Busy } [10588.506335] ata1: hard resetting link [10588.508342] ata1: controller in dubious state, performing PORT_RST [10590.699055] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10) [10590.702324] ata1.00: configured for UDMA/33 [10590.704363] sd 0:0:0:0: [sdj] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [10590.706425] sd 0:0:0:0: [sdj] tag#0 Sense Key : Aborted Command [current] [10590.708464] sd 0:0:0:0: [sdj] tag#0 Add. Sense: Scsi parity error [10590.710512] sd 0:0:0:0: [sdj] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 d3 d4 e0 00 00 01 00 00 00 [10590.712560] blk_update_request: I/O error, dev sdj, sector 13882592 [10590.714663] ata1: EH complete