@@ -3,10 +3,27 @@
Required properties:
- compatible : should be one of the following:
"altr,socfpga-denali-nand" - for Altera SOCFPGA
+ "socionext,uniphier-denali-nand-v5a" - for Socionext UniPhier (v5a)
+ "socionext,uniphier-denali-nand-v5b" - for Socionext UniPhier (v5b)
- reg : should contain registers location and length for data and reg.
- reg-names: Should contain the reg names "nand_data" and "denali_reg"
- interrupts : The interrupt number.
+Optional properties:
+ - nand-ecc-step-size: must be 512 or 1024. If not specified, default to:
+ 512 for "altr,socfpga-denali-nand"
+ 1024 for "socionext,uniphier-denali-nand-v5a"
+ 1024 for "socionext,uniphier-denali-nand-v5b"
+ see nand.txt for details.
+ - nand-ecc-strength: see nand.txt for details. Available values are:
+ 8, 15 for "altr,socfpga-denali-nand"
+ 8, 16, 24 for "socionext,uniphier-denali-nand-v5a"
+ 8, 16 for "socionext,uniphier-denali-nand-v5b"
+ - nand-ecc-maximize: see nand.txt for details
+
+Note:
+Either nand-ecc-strength or nand-ecc-maximize should be specified.
+
The device tree may optionally contain sub-nodes describing partitions of the
address space. See partition.txt for more detail.
@@ -23,52 +23,21 @@
#include <linux/mutex.h>
#include <linux/mtd/mtd.h>
#include <linux/module.h>
+#include <linux/slab.h>
#include "denali.h"
MODULE_LICENSE("GPL");
-/*
- * We define a module parameter that allows the user to override
- * the hardware and decide what timing mode should be used.
- */
-#define NAND_DEFAULT_TIMINGS -1
-
-static int onfi_timing_mode = NAND_DEFAULT_TIMINGS;
-module_param(onfi_timing_mode, int, S_IRUGO);
-MODULE_PARM_DESC(onfi_timing_mode,
- "Overrides default ONFI setting. -1 indicates use default timings");
-
#define DENALI_NAND_NAME "denali-nand"
/*
- * We define a macro here that combines all interrupts this driver uses into
- * a single constant value, for convenience.
- */
-#define DENALI_IRQ_ALL (INTR__DMA_CMD_COMP | \
- INTR__ECC_TRANSACTION_DONE | \
- INTR__ECC_ERR | \
- INTR__PROGRAM_FAIL | \
- INTR__LOAD_COMP | \
- INTR__PROGRAM_COMP | \
- INTR__TIME_OUT | \
- INTR__ERASE_FAIL | \
- INTR__RST_COMP | \
- INTR__ERASE_COMP)
-
-/*
* indicates whether or not the internal value for the flash bank is
* valid or not
*/
#define CHIP_SELECT_INVALID -1
/*
- * This macro divides two integers and rounds fractional values up
- * to the nearest integer value.
- */
-#define CEIL_DIV(X, Y) (((X)%(Y)) ? ((X)/(Y)+1) : ((X)/(Y)))
-
-/*
* this macro allows us to convert from an MTD structure to our own
* device context (denali) structure.
*/
@@ -85,8 +54,7 @@ static inline struct denali_nand_info *mtd_to_denali(struct mtd_info *mtd)
#define MAIN_ACCESS 0x42
#define MAIN_SPARE_ACCESS 0x43
-#define DENALI_READ 0
-#define DENALI_WRITE 0x100
+#define DENALI_NR_BANKS 4
/*
* this is a helper macro that allows us to
@@ -94,13 +62,13 @@ static inline struct denali_nand_info *mtd_to_denali(struct mtd_info *mtd)
*/
#define BANK(x) ((x) << 24)
-/* forward declarations */
-static void clear_interrupts(struct denali_nand_info *denali);
-static uint32_t wait_for_irq(struct denali_nand_info *denali,
- uint32_t irq_mask);
-static void denali_irq_enable(struct denali_nand_info *denali,
- uint32_t int_mask);
-static uint32_t read_interrupt_status(struct denali_nand_info *denali);
+/*
+ * The bus interface clock, clk_x, is phase aligned with the core clock. The
+ * clk_x is an integral multiple N of the core clk. The value N is configured
+ * at IP delivery time, and its available value is 4, 5, or 6. We need to align
+ * to the largest value to make it work with any possible configuration.
+ */
+#define DENALI_CLK_X_MULT 6
/*
* Certain operations for the denali NAND controller use an indexed mode to
@@ -115,595 +83,244 @@ static void index_addr(struct denali_nand_info *denali,
iowrite32(data, denali->flash_mem + 0x10);
}
-/* Perform an indexed read of the device */
-static void index_addr_read_data(struct denali_nand_info *denali,
- uint32_t address, uint32_t *pdata)
-{
- iowrite32(address, denali->flash_mem);
- *pdata = ioread32(denali->flash_mem + 0x10);
-}
-
/*
- * We need to buffer some data for some of the NAND core routines.
- * The operations manage buffering that data.
+ * Use the configuration feature register to determine the maximum number of
+ * banks that the hardware supports.
*/
-static void reset_buf(struct denali_nand_info *denali)
-{
- denali->buf.head = denali->buf.tail = 0;
-}
-
-static void write_byte_to_buf(struct denali_nand_info *denali, uint8_t byte)
-{
- denali->buf.buf[denali->buf.tail++] = byte;
-}
-
-/* reads the status of the device */
-static void read_status(struct denali_nand_info *denali)
+static void detect_max_banks(struct denali_nand_info *denali)
{
- uint32_t cmd;
+ uint32_t features = ioread32(denali->flash_reg + FEATURES);
- /* initialize the data buffer to store status */
- reset_buf(denali);
+ denali->max_banks = 1 << (features & FEATURES__N_BANKS);
- cmd = ioread32(denali->flash_reg + WRITE_PROTECT);
- if (cmd)
- write_byte_to_buf(denali, NAND_STATUS_WP);
- else
- write_byte_to_buf(denali, 0);
+ /* the encoding changed from rev 5.0 to 5.1 */
+ if (denali->revision < 0x0501)
+ denali->max_banks <<= 1;
}
-/* resets a specific device connected to the core */
-static void reset_bank(struct denali_nand_info *denali)
+static void denali_enable_irq(struct denali_nand_info *denali)
{
- uint32_t irq_status;
- uint32_t irq_mask = INTR__RST_COMP | INTR__TIME_OUT;
-
- clear_interrupts(denali);
-
- iowrite32(1 << denali->flash_bank, denali->flash_reg + DEVICE_RESET);
-
- irq_status = wait_for_irq(denali, irq_mask);
+ int i;
- if (irq_status & INTR__TIME_OUT)
- dev_err(denali->dev, "reset bank failed.\n");
+ for (i = 0; i < DENALI_NR_BANKS; i++)
+ iowrite32(U32_MAX, denali->flash_reg + INTR_EN(i));
+ iowrite32(GLOBAL_INT_EN_FLAG, denali->flash_reg + GLOBAL_INT_ENABLE);
}
-/* Reset the flash controller */
-static uint16_t denali_nand_reset(struct denali_nand_info *denali)
+static void denali_disable_irq(struct denali_nand_info *denali)
{
int i;
- for (i = 0; i < denali->max_banks; i++)
- iowrite32(INTR__RST_COMP | INTR__TIME_OUT,
- denali->flash_reg + INTR_STATUS(i));
-
- for (i = 0; i < denali->max_banks; i++) {
- iowrite32(1 << i, denali->flash_reg + DEVICE_RESET);
- while (!(ioread32(denali->flash_reg + INTR_STATUS(i)) &
- (INTR__RST_COMP | INTR__TIME_OUT)))
- cpu_relax();
- if (ioread32(denali->flash_reg + INTR_STATUS(i)) &
- INTR__TIME_OUT)
- dev_dbg(denali->dev,
- "NAND Reset operation timed out on bank %d\n", i);
- }
-
- for (i = 0; i < denali->max_banks; i++)
- iowrite32(INTR__RST_COMP | INTR__TIME_OUT,
- denali->flash_reg + INTR_STATUS(i));
-
- return PASS;
+ for (i = 0; i < DENALI_NR_BANKS; i++)
+ iowrite32(0, denali->flash_reg + INTR_EN(i));
+ iowrite32(0, denali->flash_reg + GLOBAL_INT_ENABLE);
}
-/*
- * this routine calculates the ONFI timing values for a given mode and
- * programs the clocking register accordingly. The mode is determined by
- * the get_onfi_nand_para routine.
- */
-static void nand_onfi_timing_set(struct denali_nand_info *denali,
- uint16_t mode)
+static void denali_clear_irq(struct denali_nand_info *denali,
+ int bank, uint32_t irq_status)
{
- uint16_t Trea[6] = {40, 30, 25, 20, 20, 16};
- uint16_t Trp[6] = {50, 25, 17, 15, 12, 10};
- uint16_t Treh[6] = {30, 15, 15, 10, 10, 7};
- uint16_t Trc[6] = {100, 50, 35, 30, 25, 20};
- uint16_t Trhoh[6] = {0, 15, 15, 15, 15, 15};
- uint16_t Trloh[6] = {0, 0, 0, 0, 5, 5};
- uint16_t Tcea[6] = {100, 45, 30, 25, 25, 25};
- uint16_t Tadl[6] = {200, 100, 100, 100, 70, 70};
- uint16_t Trhw[6] = {200, 100, 100, 100, 100, 100};
- uint16_t Trhz[6] = {200, 100, 100, 100, 100, 100};
- uint16_t Twhr[6] = {120, 80, 80, 60, 60, 60};
- uint16_t Tcs[6] = {70, 35, 25, 25, 20, 15};
-
- uint16_t data_invalid_rhoh, data_invalid_rloh, data_invalid;
- uint16_t dv_window = 0;
- uint16_t en_lo, en_hi;
- uint16_t acc_clks;
- uint16_t addr_2_data, re_2_we, re_2_re, we_2_re, cs_cnt;
-
- en_lo = CEIL_DIV(Trp[mode], CLK_X);
- en_hi = CEIL_DIV(Treh[mode], CLK_X);
-#if ONFI_BLOOM_TIME
- if ((en_hi * CLK_X) < (Treh[mode] + 2))
- en_hi++;
-#endif
-
- if ((en_lo + en_hi) * CLK_X < Trc[mode])
- en_lo += CEIL_DIV((Trc[mode] - (en_lo + en_hi) * CLK_X), CLK_X);
-
- if ((en_lo + en_hi) < CLK_MULTI)
- en_lo += CLK_MULTI - en_lo - en_hi;
-
- while (dv_window < 8) {
- data_invalid_rhoh = en_lo * CLK_X + Trhoh[mode];
-
- data_invalid_rloh = (en_lo + en_hi) * CLK_X + Trloh[mode];
-
- data_invalid = data_invalid_rhoh < data_invalid_rloh ?
- data_invalid_rhoh : data_invalid_rloh;
-
- dv_window = data_invalid - Trea[mode];
-
- if (dv_window < 8)
- en_lo++;
- }
-
- acc_clks = CEIL_DIV(Trea[mode], CLK_X);
-
- while (acc_clks * CLK_X - Trea[mode] < 3)
- acc_clks++;
-
- if (data_invalid - acc_clks * CLK_X < 2)
- dev_warn(denali->dev, "%s, Line %d: Warning!\n",
- __FILE__, __LINE__);
-
- addr_2_data = CEIL_DIV(Tadl[mode], CLK_X);
- re_2_we = CEIL_DIV(Trhw[mode], CLK_X);
- re_2_re = CEIL_DIV(Trhz[mode], CLK_X);
- we_2_re = CEIL_DIV(Twhr[mode], CLK_X);
- cs_cnt = CEIL_DIV((Tcs[mode] - Trp[mode]), CLK_X);
- if (cs_cnt == 0)
- cs_cnt = 1;
-
- if (Tcea[mode]) {
- while (cs_cnt * CLK_X + Trea[mode] < Tcea[mode])
- cs_cnt++;
- }
-
-#if MODE5_WORKAROUND
- if (mode == 5)
- acc_clks = 5;
-#endif
-
- /* Sighting 3462430: Temporary hack for MT29F128G08CJABAWP:B */
- if (ioread32(denali->flash_reg + MANUFACTURER_ID) == 0 &&
- ioread32(denali->flash_reg + DEVICE_ID) == 0x88)
- acc_clks = 6;
-
- iowrite32(acc_clks, denali->flash_reg + ACC_CLKS);
- iowrite32(re_2_we, denali->flash_reg + RE_2_WE);
- iowrite32(re_2_re, denali->flash_reg + RE_2_RE);
- iowrite32(we_2_re, denali->flash_reg + WE_2_RE);
- iowrite32(addr_2_data, denali->flash_reg + ADDR_2_DATA);
- iowrite32(en_lo, denali->flash_reg + RDWR_EN_LO_CNT);
- iowrite32(en_hi, denali->flash_reg + RDWR_EN_HI_CNT);
- iowrite32(cs_cnt, denali->flash_reg + CS_SETUP_CNT);
+ /* write one to clear bits */
+ iowrite32(irq_status, denali->flash_reg + INTR_STATUS(bank));
}
-/* queries the NAND device to see what ONFI modes it supports. */
-static uint16_t get_onfi_nand_para(struct denali_nand_info *denali)
+static void denali_clear_irq_all(struct denali_nand_info *denali)
{
int i;
- /*
- * we needn't to do a reset here because driver has already
- * reset all the banks before
- */
- if (!(ioread32(denali->flash_reg + ONFI_TIMING_MODE) &
- ONFI_TIMING_MODE__VALUE))
- return FAIL;
-
- for (i = 5; i > 0; i--) {
- if (ioread32(denali->flash_reg + ONFI_TIMING_MODE) &
- (0x01 << i))
- break;
- }
-
- nand_onfi_timing_set(denali, i);
-
- /*
- * By now, all the ONFI devices we know support the page cache
- * rw feature. So here we enable the pipeline_rw_ahead feature
- */
- /* iowrite32(1, denali->flash_reg + CACHE_WRITE_ENABLE); */
- /* iowrite32(1, denali->flash_reg + CACHE_READ_ENABLE); */
-
- return PASS;
+ for (i = 0; i < DENALI_NR_BANKS; i++)
+ denali_clear_irq(denali, i, U32_MAX);
}
-static void get_samsung_nand_para(struct denali_nand_info *denali,
- uint8_t device_id)
+static irqreturn_t denali_isr(int irq, void *dev_id)
{
- if (device_id == 0xd3) { /* Samsung K9WAG08U1A */
- /* Set timing register values according to datasheet */
- iowrite32(5, denali->flash_reg + ACC_CLKS);
- iowrite32(20, denali->flash_reg + RE_2_WE);
- iowrite32(12, denali->flash_reg + WE_2_RE);
- iowrite32(14, denali->flash_reg + ADDR_2_DATA);
- iowrite32(3, denali->flash_reg + RDWR_EN_LO_CNT);
- iowrite32(2, denali->flash_reg + RDWR_EN_HI_CNT);
- iowrite32(2, denali->flash_reg + CS_SETUP_CNT);
- }
-}
+ struct denali_nand_info *denali = dev_id;
+ irqreturn_t ret = IRQ_NONE;
+ uint32_t irq_status;
+ int i;
-static void get_toshiba_nand_para(struct denali_nand_info *denali)
-{
- /*
- * Workaround to fix a controller bug which reports a wrong
- * spare area size for some kind of Toshiba NAND device
- */
- if ((ioread32(denali->flash_reg + DEVICE_MAIN_AREA_SIZE) == 4096) &&
- (ioread32(denali->flash_reg + DEVICE_SPARE_AREA_SIZE) == 64))
- iowrite32(216, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
-}
+ spin_lock(&denali->irq_lock);
-static void get_hynix_nand_para(struct denali_nand_info *denali,
- uint8_t device_id)
-{
- switch (device_id) {
- case 0xD5: /* Hynix H27UAG8T2A, H27UBG8U5A or H27UCG8VFA */
- case 0xD7: /* Hynix H27UDG8VEM, H27UCG8UDM or H27UCG8V5A */
- iowrite32(128, denali->flash_reg + PAGES_PER_BLOCK);
- iowrite32(4096, denali->flash_reg + DEVICE_MAIN_AREA_SIZE);
- iowrite32(224, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
- iowrite32(0, denali->flash_reg + DEVICE_WIDTH);
- break;
- default:
- dev_warn(denali->dev,
- "Unknown Hynix NAND (Device ID: 0x%x).\n"
- "Will use default parameter values instead.\n",
- device_id);
- }
-}
+ for (i = 0; i < DENALI_NR_BANKS; i++) {
+ irq_status = ioread32(denali->flash_reg + INTR_STATUS(i));
+ if (irq_status)
+ ret = IRQ_HANDLED;
-/*
- * determines how many NAND chips are connected to the controller. Note for
- * Intel CE4100 devices we don't support more than one device.
- */
-static void find_valid_banks(struct denali_nand_info *denali)
-{
- uint32_t id[denali->max_banks];
- int i;
+ denali_clear_irq(denali, i, irq_status);
- denali->total_used_banks = 1;
- for (i = 0; i < denali->max_banks; i++) {
- index_addr(denali, MODE_11 | (i << 24) | 0, 0x90);
- index_addr(denali, MODE_11 | (i << 24) | 1, 0);
- index_addr_read_data(denali, MODE_11 | (i << 24) | 2, &id[i]);
+ if (i != denali->flash_bank)
+ continue;
- dev_dbg(denali->dev,
- "Return 1st ID for bank[%d]: %x\n", i, id[i]);
+ denali->irq_status |= irq_status;
- if (i == 0) {
- if (!(id[i] & 0x0ff))
- break; /* WTF? */
- } else {
- if ((id[i] & 0x0ff) == (id[0] & 0x0ff))
- denali->total_used_banks++;
- else
- break;
- }
- }
-
- if (denali->platform == INTEL_CE4100) {
- /*
- * Platform limitations of the CE4100 device limit
- * users to a single chip solution for NAND.
- * Multichip support is not enabled.
- */
- if (denali->total_used_banks != 1) {
- dev_err(denali->dev,
- "Sorry, Intel CE4100 only supports a single NAND device.\n");
- BUG();
- }
+ if (denali->irq_status & denali->irq_mask)
+ complete(&denali->complete);
}
- dev_dbg(denali->dev,
- "denali->total_used_banks: %d\n", denali->total_used_banks);
-}
-
-/*
- * Use the configuration feature register to determine the maximum number of
- * banks that the hardware supports.
- */
-static void detect_max_banks(struct denali_nand_info *denali)
-{
- uint32_t features = ioread32(denali->flash_reg + FEATURES);
- denali->max_banks = 1 << (features & FEATURES__N_BANKS);
+ spin_unlock(&denali->irq_lock);
- /* the encoding changed from rev 5.0 to 5.1 */
- if (denali->revision < 0x0501)
- denali->max_banks <<= 1;
+ return ret;
}
-static uint16_t denali_nand_timing_set(struct denali_nand_info *denali)
+static void denali_reset_irq(struct denali_nand_info *denali)
{
- uint16_t status = PASS;
- uint32_t id_bytes[8], addr;
- uint8_t maf_id, device_id;
- int i;
-
- /*
- * Use read id method to get device ID and other params.
- * For some NAND chips, controller can't report the correct
- * device ID by reading from DEVICE_ID register
- */
- addr = MODE_11 | BANK(denali->flash_bank);
- index_addr(denali, addr | 0, 0x90);
- index_addr(denali, addr | 1, 0);
- for (i = 0; i < 8; i++)
- index_addr_read_data(denali, addr | 2, &id_bytes[i]);
- maf_id = id_bytes[0];
- device_id = id_bytes[1];
-
- if (ioread32(denali->flash_reg + ONFI_DEVICE_NO_OF_LUNS) &
- ONFI_DEVICE_NO_OF_LUNS__ONFI_DEVICE) { /* ONFI 1.0 NAND */
- if (FAIL == get_onfi_nand_para(denali))
- return FAIL;
- } else if (maf_id == 0xEC) { /* Samsung NAND */
- get_samsung_nand_para(denali, device_id);
- } else if (maf_id == 0x98) { /* Toshiba NAND */
- get_toshiba_nand_para(denali);
- } else if (maf_id == 0xAD) { /* Hynix NAND */
- get_hynix_nand_para(denali, device_id);
- }
-
- dev_info(denali->dev,
- "Dump timing register values:\n"
- "acc_clks: %d, re_2_we: %d, re_2_re: %d\n"
- "we_2_re: %d, addr_2_data: %d, rdwr_en_lo_cnt: %d\n"
- "rdwr_en_hi_cnt: %d, cs_setup_cnt: %d\n",
- ioread32(denali->flash_reg + ACC_CLKS),
- ioread32(denali->flash_reg + RE_2_WE),
- ioread32(denali->flash_reg + RE_2_RE),
- ioread32(denali->flash_reg + WE_2_RE),
- ioread32(denali->flash_reg + ADDR_2_DATA),
- ioread32(denali->flash_reg + RDWR_EN_LO_CNT),
- ioread32(denali->flash_reg + RDWR_EN_HI_CNT),
- ioread32(denali->flash_reg + CS_SETUP_CNT));
-
- find_valid_banks(denali);
-
- /*
- * If the user specified to override the default timings
- * with a specific ONFI mode, we apply those changes here.
- */
- if (onfi_timing_mode != NAND_DEFAULT_TIMINGS)
- nand_onfi_timing_set(denali, onfi_timing_mode);
+ unsigned long flags;
- return status;
+ spin_lock_irqsave(&denali->irq_lock, flags);
+ denali->irq_status = 0;
+ denali->irq_mask = 0;
+ spin_unlock_irqrestore(&denali->irq_lock, flags);
}
-static void denali_set_intr_modes(struct denali_nand_info *denali,
- uint16_t INT_ENABLE)
+static uint32_t denali_wait_for_irq(struct denali_nand_info *denali,
+ uint32_t irq_mask)
{
- if (INT_ENABLE)
- iowrite32(1, denali->flash_reg + GLOBAL_INT_ENABLE);
- else
- iowrite32(0, denali->flash_reg + GLOBAL_INT_ENABLE);
-}
+ unsigned long time_left, flags;
+ uint32_t irq_status;
-/*
- * validation function to verify that the controlling software is making
- * a valid request
- */
-static inline bool is_flash_bank_valid(int flash_bank)
-{
- return flash_bank >= 0 && flash_bank < 4;
-}
+ spin_lock_irqsave(&denali->irq_lock, flags);
-static void denali_irq_init(struct denali_nand_info *denali)
-{
- uint32_t int_mask;
- int i;
+ irq_status = denali->irq_status;
- /* Disable global interrupts */
- denali_set_intr_modes(denali, false);
+ if (irq_mask & irq_status) {
+ spin_unlock_irqrestore(&denali->irq_lock, flags);
+ return irq_status;
+ }
- int_mask = DENALI_IRQ_ALL;
+ denali->irq_mask = irq_mask;
+ reinit_completion(&denali->complete);
+ spin_unlock_irqrestore(&denali->irq_lock, flags);
- /* Clear all status bits */
- for (i = 0; i < denali->max_banks; ++i)
- iowrite32(0xFFFF, denali->flash_reg + INTR_STATUS(i));
+ time_left = wait_for_completion_timeout(&denali->complete,
+ msecs_to_jiffies(1000));
+ if (!time_left) {
+ dev_err(denali->dev, "timeout while waiting for irq 0x%x\n",
+ denali->irq_mask);
+ return 0;
+ }
- denali_irq_enable(denali, int_mask);
+ return denali->irq_status;
}
-static void denali_irq_cleanup(int irqnum, struct denali_nand_info *denali)
+static uint32_t denali_check_irq(struct denali_nand_info *denali)
{
- denali_set_intr_modes(denali, false);
-}
+ unsigned long flags;
+ uint32_t irq_status;
-static void denali_irq_enable(struct denali_nand_info *denali,
- uint32_t int_mask)
-{
- int i;
+ spin_lock_irqsave(&denali->irq_lock, flags);
+ irq_status = denali->irq_status;
+ spin_unlock_irqrestore(&denali->irq_lock, flags);
- for (i = 0; i < denali->max_banks; ++i)
- iowrite32(int_mask, denali->flash_reg + INTR_EN(i));
+ return irq_status;
}
/*
- * This function only returns when an interrupt that this driver cares about
- * occurs. This is to reduce the overhead of servicing interrupts
+ * This helper function setups the registers for ECC and whether or not
+ * the spare area will be transferred.
*/
-static inline uint32_t denali_irq_detected(struct denali_nand_info *denali)
+static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en,
+ bool transfer_spare)
{
- return read_interrupt_status(denali) & DENALI_IRQ_ALL;
+ int ecc_en_flag, transfer_spare_flag;
+
+ /* set ECC, transfer spare bits if needed */
+ ecc_en_flag = ecc_en ? ECC_ENABLE__FLAG : 0;
+ transfer_spare_flag = transfer_spare ? TRANSFER_SPARE_REG__FLAG : 0;
+
+ /* Enable spare area/ECC per user's request. */
+ iowrite32(ecc_en_flag, denali->flash_reg + ECC_ENABLE);
+ iowrite32(transfer_spare_flag, denali->flash_reg + TRANSFER_SPARE_REG);
}
-/* Interrupts are cleared by writing a 1 to the appropriate status bit */
-static inline void clear_interrupt(struct denali_nand_info *denali,
- uint32_t irq_mask)
+static uint8_t denali_read_byte(struct mtd_info *mtd)
{
- uint32_t intr_status_reg;
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
- intr_status_reg = INTR_STATUS(denali->flash_bank);
+ iowrite32(MODE_11 | BANK(denali->flash_bank) | 2, denali->flash_mem);
- iowrite32(irq_mask, denali->flash_reg + intr_status_reg);
+ return ioread32(denali->flash_mem + 0x10);
}
-static void clear_interrupts(struct denali_nand_info *denali)
+static void denali_write_byte(struct mtd_info *mtd, uint8_t byte)
{
- uint32_t status;
-
- spin_lock_irq(&denali->irq_lock);
-
- status = read_interrupt_status(denali);
- clear_interrupt(denali, status);
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
- denali->irq_status = 0x0;
- spin_unlock_irq(&denali->irq_lock);
+ index_addr(denali, MODE_11 | BANK(denali->flash_bank) | 2, byte);
}
-static uint32_t read_interrupt_status(struct denali_nand_info *denali)
+static void denali_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
{
- uint32_t intr_status_reg;
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ int i;
- intr_status_reg = INTR_STATUS(denali->flash_bank);
+ iowrite32(MODE_11 | BANK(denali->flash_bank) | 2, denali->flash_mem);
- return ioread32(denali->flash_reg + intr_status_reg);
+ for (i = 0; i < len; i++)
+ buf[i] = ioread32(denali->flash_mem + 0x10);
}
-/*
- * This is the interrupt service routine. It handles all interrupts
- * sent to this device. Note that on CE4100, this is a shared interrupt.
- */
-static irqreturn_t denali_isr(int irq, void *dev_id)
+static void denali_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
{
- struct denali_nand_info *denali = dev_id;
- uint32_t irq_status;
- irqreturn_t result = IRQ_NONE;
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ int i;
- spin_lock(&denali->irq_lock);
+ iowrite32(MODE_11 | BANK(denali->flash_bank) | 2, denali->flash_mem);
- /* check to see if a valid NAND chip has been selected. */
- if (is_flash_bank_valid(denali->flash_bank)) {
- /*
- * check to see if controller generated the interrupt,
- * since this is a shared interrupt
- */
- irq_status = denali_irq_detected(denali);
- if (irq_status != 0) {
- /* handle interrupt */
- /* first acknowledge it */
- clear_interrupt(denali, irq_status);
- /*
- * store the status in the device context for someone
- * to read
- */
- denali->irq_status |= irq_status;
- /* notify anyone who cares that it happened */
- complete(&denali->complete);
- /* tell the OS that we've handled this */
- result = IRQ_HANDLED;
- }
- }
- spin_unlock(&denali->irq_lock);
- return result;
+ for (i = 0; i < len; i++)
+ iowrite32(buf[i], denali->flash_mem + 0x10);
}
-static uint32_t wait_for_irq(struct denali_nand_info *denali, uint32_t irq_mask)
+static void denali_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
{
- unsigned long comp_res;
- uint32_t intr_status;
- unsigned long timeout = msecs_to_jiffies(1000);
-
- do {
- comp_res =
- wait_for_completion_timeout(&denali->complete, timeout);
- spin_lock_irq(&denali->irq_lock);
- intr_status = denali->irq_status;
-
- if (intr_status & irq_mask) {
- denali->irq_status &= ~irq_mask;
- spin_unlock_irq(&denali->irq_lock);
- /* our interrupt was detected */
- break;
- }
-
- /*
- * these are not the interrupts you are looking for -
- * need to wait again
- */
- spin_unlock_irq(&denali->irq_lock);
- } while (comp_res != 0);
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint16_t *buf16 = (uint16_t *)buf;
+ int i;
- if (comp_res == 0) {
- /* timeout */
- pr_err("timeout occurred, status = 0x%x, mask = 0x%x\n",
- intr_status, irq_mask);
+ iowrite32(MODE_11 | BANK(denali->flash_bank) | 2, denali->flash_mem);
- intr_status = 0;
- }
- return intr_status;
+ for (i = 0; i < len / 2; i++)
+ buf16[i] = ioread32(denali->flash_mem + 0x10);
}
-/*
- * This helper function setups the registers for ECC and whether or not
- * the spare area will be transferred.
- */
-static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en,
- bool transfer_spare)
+static void denali_write_buf16(struct mtd_info *mtd, const uint8_t *buf,
+ int len)
{
- int ecc_en_flag, transfer_spare_flag;
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ const uint16_t *buf16 = (const uint16_t *)buf;
+ int i;
- /* set ECC, transfer spare bits if needed */
- ecc_en_flag = ecc_en ? ECC_ENABLE__FLAG : 0;
- transfer_spare_flag = transfer_spare ? TRANSFER_SPARE_REG__FLAG : 0;
+ iowrite32(MODE_11 | BANK(denali->flash_bank) | 2, denali->flash_mem);
- /* Enable spare area/ECC per user's request. */
- iowrite32(ecc_en_flag, denali->flash_reg + ECC_ENABLE);
- iowrite32(transfer_spare_flag, denali->flash_reg + TRANSFER_SPARE_REG);
+ for (i = 0; i < len / 2; i++)
+ iowrite32(buf16[i], denali->flash_mem + 0x10);
}
-/*
- * sends a pipeline command operation to the controller. See the Denali NAND
- * controller's user guide for more information (section 4.2.3.6).
- */
-static int denali_send_pipeline_cmd(struct denali_nand_info *denali,
- bool ecc_en, bool transfer_spare,
- int access_type, int op)
+static void denali_cmd_ctrl(struct mtd_info *mtd, int dat, unsigned int ctrl)
{
- int status = PASS;
- uint32_t addr, cmd;
-
- setup_ecc_for_xfer(denali, ecc_en, transfer_spare);
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t type;
- clear_interrupts(denali);
+ if (ctrl & NAND_CLE)
+ type = 0;
+ else if (ctrl & NAND_ALE)
+ type = 1;
+ else
+ return;
- addr = BANK(denali->flash_bank) | denali->page;
+ /*
+ * Some commands are followed by chip->dev_ready or chip->waitfunc.
+ * irq_status must be cleared here to catch the R/B# interrupt later.
+ */
+ if (ctrl & NAND_CTRL_CHANGE)
+ denali_reset_irq(denali);
- if (op == DENALI_WRITE && access_type != SPARE_ACCESS) {
- cmd = MODE_01 | addr;
- iowrite32(cmd, denali->flash_mem);
- } else if (op == DENALI_WRITE && access_type == SPARE_ACCESS) {
- /* read spare area */
- cmd = MODE_10 | addr;
- index_addr(denali, cmd, access_type);
+ index_addr(denali, MODE_11 | BANK(denali->flash_bank) | type, dat);
+}
- cmd = MODE_01 | addr;
- iowrite32(cmd, denali->flash_mem);
- } else if (op == DENALI_READ) {
- /* setup page read request for access type */
- cmd = MODE_10 | addr;
- index_addr(denali, cmd, access_type);
+static int denali_dev_ready(struct mtd_info *mtd)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
- cmd = MODE_01 | addr;
- iowrite32(cmd, denali->flash_mem);
- }
- return status;
+ return !!(denali_check_irq(denali) & INTR__INT_ACT);
}
/* helper function that simply writes a buffer to the flash */
@@ -748,71 +365,6 @@ static int read_data_from_flash_mem(struct denali_nand_info *denali,
return i * 4; /* intent is to return the number of bytes read */
}
-/* writes OOB data to the device */
-static int write_oob_data(struct mtd_info *mtd, uint8_t *buf, int page)
-{
- struct denali_nand_info *denali = mtd_to_denali(mtd);
- uint32_t irq_status;
- uint32_t irq_mask = INTR__PROGRAM_COMP | INTR__PROGRAM_FAIL;
- int status = 0;
-
- denali->page = page;
-
- if (denali_send_pipeline_cmd(denali, false, false, SPARE_ACCESS,
- DENALI_WRITE) == PASS) {
- write_data_to_flash_mem(denali, buf, mtd->oobsize);
-
- /* wait for operation to complete */
- irq_status = wait_for_irq(denali, irq_mask);
-
- if (irq_status == 0) {
- dev_err(denali->dev, "OOB write failed\n");
- status = -EIO;
- }
- } else {
- dev_err(denali->dev, "unable to send pipeline command\n");
- status = -EIO;
- }
- return status;
-}
-
-/* reads OOB data from the device */
-static void read_oob_data(struct mtd_info *mtd, uint8_t *buf, int page)
-{
- struct denali_nand_info *denali = mtd_to_denali(mtd);
- uint32_t irq_mask = INTR__LOAD_COMP;
- uint32_t irq_status, addr, cmd;
-
- denali->page = page;
-
- if (denali_send_pipeline_cmd(denali, false, true, SPARE_ACCESS,
- DENALI_READ) == PASS) {
- read_data_from_flash_mem(denali, buf, mtd->oobsize);
-
- /*
- * wait for command to be accepted
- * can always use status0 bit as the
- * mask is identical for each bank.
- */
- irq_status = wait_for_irq(denali, irq_mask);
-
- if (irq_status == 0)
- dev_err(denali->dev, "page on OOB timeout %d\n",
- denali->page);
-
- /*
- * We set the device back to MAIN_ACCESS here as I observed
- * instability with the controller if you do a block erase
- * and the last transaction was a SPARE_ACCESS. Block erase
- * is reliable (according to the MTD test infrastructure)
- * if you are in MAIN_ACCESS.
- */
- addr = BANK(denali->flash_bank) | denali->page;
- cmd = MODE_10 | addr;
- index_addr(denali, cmd, MAIN_ACCESS);
- }
-}
-
static int denali_check_erased_page(struct mtd_info *mtd,
struct nand_chip *chip, uint8_t *buf,
unsigned long uncor_ecc_flags,
@@ -886,8 +438,6 @@ static int denali_hw_ecc_fixup(struct mtd_info *mtd,
return max_bitflips;
}
-#define ECC_SECTOR_SIZE 512
-
#define ECC_SECTOR(x) (((x) & ECC_ERROR_ADDRESS__SECTOR_NR) >> 12)
#define ECC_BYTE(x) (((x) & ECC_ERROR_ADDRESS__OFFSET))
#define ECC_CORRECTION_VALUE(x) ((x) & ERR_CORRECTION_INFO__BYTEMASK)
@@ -899,15 +449,16 @@ static int denali_sw_ecc_fixup(struct mtd_info *mtd,
struct denali_nand_info *denali,
unsigned long *uncor_ecc_flags, uint8_t *buf)
{
+ unsigned int ecc_size = denali->nand.ecc.size;
unsigned int bitflips = 0;
unsigned int max_bitflips = 0;
uint32_t err_addr, err_cor_info;
unsigned int err_byte, err_sector, err_device;
uint8_t err_cor_value;
unsigned int prev_sector = 0;
+ uint32_t irq_status;
- /* read the ECC errors. we'll ignore them for now */
- denali_set_intr_modes(denali, false);
+ denali_reset_irq(denali);
do {
err_addr = ioread32(denali->flash_reg + ECC_ERROR_ADDRESS);
@@ -928,9 +479,9 @@ static int denali_sw_ecc_fixup(struct mtd_info *mtd,
* an erased sector.
*/
*uncor_ecc_flags |= BIT(err_sector);
- } else if (err_byte < ECC_SECTOR_SIZE) {
+ } else if (err_byte < ecc_size) {
/*
- * If err_byte is larger than ECC_SECTOR_SIZE, means error
+ * If err_byte is larger than ecc_size, means error
* happened in OOB, so we ignore it. It's no need for
* us to correct it err_device is represented the NAND
* error bits are happened in if there are more than
@@ -939,7 +490,7 @@ static int denali_sw_ecc_fixup(struct mtd_info *mtd,
int offset;
unsigned int flips_in_byte;
- offset = (err_sector * ECC_SECTOR_SIZE + err_byte) *
+ offset = (err_sector * ecc_size + err_byte) *
denali->devnum + err_device;
/* correct the ECC error */
@@ -959,10 +510,9 @@ static int denali_sw_ecc_fixup(struct mtd_info *mtd,
* ECC_TRANSACTION_DONE interrupt, so here just wait for
* a while for this interrupt
*/
- while (!(read_interrupt_status(denali) & INTR__ECC_TRANSACTION_DONE))
- cpu_relax();
- clear_interrupts(denali);
- denali_set_intr_modes(denali, true);
+ irq_status = denali_wait_for_irq(denali, INTR__ECC_TRANSACTION_DONE);
+ if (!(irq_status & INTR__ECC_TRANSACTION_DONE))
+ return -EIO;
return max_bitflips;
}
@@ -974,13 +524,13 @@ static void denali_enable_dma(struct denali_nand_info *denali, bool en)
ioread32(denali->flash_reg + DMA_ENABLE);
}
-static void denali_setup_dma64(struct denali_nand_info *denali, int op)
+static void denali_setup_dma64(struct denali_nand_info *denali,
+ dma_addr_t dma_addr, int page, int write)
{
uint32_t mode;
const int page_count = 1;
- uint64_t addr = denali->buf.dma_buf;
- mode = MODE_10 | BANK(denali->flash_bank) | denali->page;
+ mode = MODE_10 | BANK(denali->flash_bank) | page;
/* DMA is a three step process */
@@ -988,191 +538,352 @@ static void denali_setup_dma64(struct denali_nand_info *denali, int op)
* 1. setup transfer type, interrupt when complete,
* burst len = 64 bytes, the number of pages
*/
- index_addr(denali, mode, 0x01002000 | (64 << 16) | op | page_count);
+ index_addr(denali, mode,
+ 0x01002000 | (64 << 16) | (write << 8) | page_count);
/* 2. set memory low address */
- index_addr(denali, mode, addr);
+ index_addr(denali, mode, dma_addr);
/* 3. set memory high address */
- index_addr(denali, mode, addr >> 32);
+ index_addr(denali, mode, (uint64_t)dma_addr >> 32);
}
-static void denali_setup_dma32(struct denali_nand_info *denali, int op)
+static void denali_setup_dma32(struct denali_nand_info *denali,
+ dma_addr_t dma_addr, int page, int write)
{
uint32_t mode;
const int page_count = 1;
- uint32_t addr = denali->buf.dma_buf;
mode = MODE_10 | BANK(denali->flash_bank);
/* DMA is a four step process */
/* 1. setup transfer type and # of pages */
- index_addr(denali, mode | denali->page, 0x2000 | op | page_count);
+ index_addr(denali, mode | page, 0x2000 | (write << 8) | page_count);
/* 2. set memory high address bits 23:8 */
- index_addr(denali, mode | ((addr >> 16) << 8), 0x2200);
+ index_addr(denali, mode | ((dma_addr >> 16) << 8), 0x2200);
/* 3. set memory low address bits 23:8 */
- index_addr(denali, mode | ((addr & 0xffff) << 8), 0x2300);
+ index_addr(denali, mode | ((dma_addr & 0xffff) << 8), 0x2300);
/* 4. interrupt when complete, burst len = 64 bytes */
index_addr(denali, mode | 0x14000, 0x2400);
}
-static void denali_setup_dma(struct denali_nand_info *denali, int op)
+static void denali_setup_dma(struct denali_nand_info *denali,
+ dma_addr_t dma_addr, int page, int write)
{
if (denali->caps & DENALI_CAP_DMA_64BIT)
- denali_setup_dma64(denali, op);
+ denali_setup_dma64(denali, dma_addr, page, write);
else
- denali_setup_dma32(denali, op);
+ denali_setup_dma32(denali, dma_addr, page, write);
}
-/*
- * writes a page. user specifies type, and this function handles the
- * configuration details.
- */
-static int write_page(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf, bool raw_xfer)
+static int denali_pio_read(struct denali_nand_info *denali, void *buf,
+ size_t size, int page, int raw)
{
- struct denali_nand_info *denali = mtd_to_denali(mtd);
- dma_addr_t addr = denali->buf.dma_buf;
- size_t size = mtd->writesize + mtd->oobsize;
+ uint32_t addr = BANK(denali->flash_bank) | page;
+ uint32_t irq_status, ecc_err_mask;
+
+ /* setup page read request for access type */
+ index_addr(denali, MODE_10 | addr,
+ raw ? MAIN_SPARE_ACCESS : MAIN_ACCESS);
+
+ iowrite32(MODE_01 | addr, denali->flash_mem);
+
+ if (denali->caps & DENALI_CAP_HW_ECC_FIXUP)
+ ecc_err_mask = INTR__ECC_UNCOR_ERR;
+ else
+ ecc_err_mask = INTR__ECC_ERR;
+
+ denali_reset_irq(denali);
+
+ read_data_from_flash_mem(denali, buf, size);
+
+ irq_status = denali_wait_for_irq(denali, INTR__PAGE_XFER_INC);
+ if (!(irq_status & INTR__PAGE_XFER_INC))
+ return -EIO;
+
+ if (irq_status & INTR__ERASED_PAGE)
+ memset(buf, 0xff, size);
+
+ return irq_status & ecc_err_mask ? -EBADMSG : 0;
+}
+
+static int denali_pio_write(struct denali_nand_info *denali,
+ const void *buf, size_t size, int page, int raw)
+{
+ uint32_t addr = BANK(denali->flash_bank) | page;
uint32_t irq_status;
- uint32_t irq_mask = INTR__DMA_CMD_COMP | INTR__PROGRAM_FAIL;
- /*
- * if it is a raw xfer, we want to disable ecc and send the spare area.
- * !raw_xfer - enable ecc
- * raw_xfer - transfer spare
- */
- setup_ecc_for_xfer(denali, !raw_xfer, raw_xfer);
+ /* setup page read request for access type */
+ index_addr(denali, MODE_10 | addr,
+ raw ? MAIN_SPARE_ACCESS : MAIN_ACCESS);
+
+ iowrite32(MODE_01 | addr, denali->flash_mem);
+
+ denali_reset_irq(denali);
+
+ write_data_to_flash_mem(denali, buf, size);
+
+ irq_status = denali_wait_for_irq(denali,
+ INTR__PROGRAM_COMP | INTR__PROGRAM_FAIL);
+ if (!(irq_status & INTR__PROGRAM_COMP))
+ return -EIO;
+
+ return 0;
+}
- /* copy buffer into DMA buffer */
- memcpy(denali->buf.buf, buf, mtd->writesize);
+static int denali_pio_xfer(struct denali_nand_info *denali, void *buf,
+ size_t size, int page, int raw, int write)
+{
+ if (write)
+ return denali_pio_write(denali, buf, size, page, raw);
+ else
+ return denali_pio_read(denali, buf, size, page, raw);
+}
- if (raw_xfer) {
- /* transfer the data to the spare area */
- memcpy(denali->buf.buf + mtd->writesize,
- chip->oob_poi,
- mtd->oobsize);
+static int denali_dma_xfer(struct denali_nand_info *denali, void *buf,
+ size_t size, int page, int raw, int write)
+{
+ dma_addr_t dma_addr;
+ uint32_t irq_mask, irq_status, ecc_err_mask;
+ enum dma_data_direction dir = write ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
+ int ret = 0;
+
+ dma_addr = dma_map_single(denali->dev, buf, size, dir);
+ if (dma_mapping_error(denali->dev, dma_addr)) {
+ dev_dbg(denali->dev, "Failed to DMA-map buffer. Trying PIO.\n");
+ return denali_pio_xfer(denali, buf, size, page, raw, write);
}
- dma_sync_single_for_device(denali->dev, addr, size, DMA_TO_DEVICE);
+ if (write) {
+ irq_mask = INTR__DMA_CMD_COMP | INTR__PROGRAM_FAIL;
+ ecc_err_mask = 0;
+ } else if (denali->caps & DENALI_CAP_HW_ECC_FIXUP) {
+ irq_mask = INTR__DMA_CMD_COMP;
+ ecc_err_mask = INTR__ECC_UNCOR_ERR;
+ } else {
+ irq_mask = INTR__DMA_CMD_COMP;
+ ecc_err_mask = INTR__ECC_ERR;
+ }
- clear_interrupts(denali);
denali_enable_dma(denali, true);
- denali_setup_dma(denali, DENALI_WRITE);
+ denali_reset_irq(denali);
+ denali_setup_dma(denali, dma_addr, page, write);
/* wait for operation to complete */
- irq_status = wait_for_irq(denali, irq_mask);
-
- if (irq_status == 0) {
- dev_err(denali->dev, "timeout on write_page (type = %d)\n",
- raw_xfer);
- denali->status = NAND_STATUS_FAIL;
- }
+ irq_status = denali_wait_for_irq(denali, irq_mask);
+ if (!(irq_status & INTR__DMA_CMD_COMP))
+ ret = -EIO;
+ else if (irq_status & ecc_err_mask)
+ ret = -EBADMSG;
denali_enable_dma(denali, false);
- dma_sync_single_for_cpu(denali->dev, addr, size, DMA_TO_DEVICE);
+ dma_unmap_single(denali->dev, dma_addr, size, dir);
- return 0;
-}
+ if (irq_status & INTR__ERASED_PAGE)
+ memset(buf, 0xff, size);
-/* NAND core entry points */
+ return ret;
+}
-/*
- * this is the callback that the NAND core calls to write a page. Since
- * writing a page with ECC or without is similar, all the work is done
- * by write_page above.
- */
-static int denali_write_page(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf, int oob_required, int page)
+static int denali_data_xfer(struct denali_nand_info *denali, void *buf,
+ size_t size, int page, int raw, int write)
{
- /*
- * for regular page writes, we let HW handle all the ECC
- * data written to the device.
- */
- return write_page(mtd, chip, buf, false);
+ setup_ecc_for_xfer(denali, !raw, raw);
+
+ if (denali->dma_avail)
+ return denali_dma_xfer(denali, buf, size, page, raw, write);
+ else
+ return denali_pio_xfer(denali, buf, size, page, raw, write);
}
-/*
- * This is the callback that the NAND core calls to write a page without ECC.
- * raw access is similar to ECC page writes, so all the work is done in the
- * write_page() function above.
- */
-static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf, int oob_required,
- int page)
+static void denali_oob_xfer(struct mtd_info *mtd, struct nand_chip *chip,
+ int page, int write)
{
- /*
- * for raw page writes, we want to disable ECC and simply write
- * whatever data is in the buffer.
- */
- return write_page(mtd, chip, buf, true);
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ unsigned int start_cmd = write ? NAND_CMD_SEQIN : NAND_CMD_READ0;
+ unsigned int rnd_cmd = write ? NAND_CMD_RNDIN : NAND_CMD_RNDOUT;
+ int writesize = mtd->writesize;
+ int oobsize = mtd->oobsize;
+ uint8_t *bufpoi = chip->oob_poi;
+ int ecc_steps = chip->ecc.steps;
+ int ecc_size = chip->ecc.size;
+ int ecc_bytes = chip->ecc.bytes;
+ int bbm_skip = denali->bbtskipbytes;
+ size_t size = writesize + oobsize;
+ int i, pos, len;
+
+ /* BBM at the beginning of the OOB area */
+ chip->cmdfunc(mtd, start_cmd, writesize, page);
+ if (write)
+ chip->write_buf(mtd, bufpoi, bbm_skip);
+ else
+ chip->read_buf(mtd, bufpoi, bbm_skip);
+ bufpoi += bbm_skip;
+
+ /* OOB ECC */
+ for (i = 0; i < ecc_steps; i++) {
+ pos = ecc_size + i * (ecc_size + ecc_bytes);
+ len = ecc_bytes;
+
+ if (pos >= writesize)
+ pos += bbm_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ chip->cmdfunc(mtd, rnd_cmd, pos, -1);
+ if (write)
+ chip->write_buf(mtd, bufpoi, len);
+ else
+ chip->read_buf(mtd, bufpoi, len);
+ bufpoi += len;
+ if (len < ecc_bytes) {
+ len = ecc_bytes - len;
+ chip->cmdfunc(mtd, rnd_cmd, writesize + bbm_skip, -1);
+ if (write)
+ chip->write_buf(mtd, bufpoi, len);
+ else
+ chip->read_buf(mtd, bufpoi, len);
+ bufpoi += len;
+ }
+ }
+
+ /* OOB free */
+ len = oobsize - (bufpoi - chip->oob_poi);
+ chip->cmdfunc(mtd, rnd_cmd, size - len, -1);
+ if (write)
+ chip->write_buf(mtd, bufpoi, len);
+ else
+ chip->read_buf(mtd, bufpoi, len);
}
-static int denali_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
- int page)
+static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
{
- return write_oob_data(mtd, chip->oob_poi, page);
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ int writesize = mtd->writesize;
+ int oobsize = mtd->oobsize;
+ int ecc_steps = chip->ecc.steps;
+ int ecc_size = chip->ecc.size;
+ int ecc_bytes = chip->ecc.bytes;
+ void *dma_buf = denali->buf;
+ int bbm_skip = denali->bbtskipbytes;
+ size_t size = writesize + oobsize;
+ int ret, i, pos, len;
+
+ ret = denali_data_xfer(denali, dma_buf, size, page, 1, 0);
+ if (ret)
+ return ret;
+
+ /* Arrange the buffer for syndrome payload/ecc layout */
+ if (buf) {
+ for (i = 0; i < ecc_steps; i++) {
+ pos = i * (ecc_size + ecc_bytes);
+ len = ecc_size;
+
+ if (pos >= writesize)
+ pos += bbm_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ memcpy(buf, dma_buf + pos, len);
+ buf += len;
+ if (len < ecc_size) {
+ len = ecc_size - len;
+ memcpy(buf, dma_buf + writesize + bbm_skip,
+ len);
+ buf += len;
+ }
+ }
+ }
+
+ if (oob_required) {
+ uint8_t *oob = chip->oob_poi;
+
+ /* BBM at the beginning of the OOB area */
+ memcpy(oob, dma_buf + writesize, bbm_skip);
+ oob += bbm_skip;
+
+ /* OOB ECC */
+ for (i = 0; i < ecc_steps; i++) {
+ pos = ecc_size + i * (ecc_size + ecc_bytes);
+ len = ecc_bytes;
+
+ if (pos >= writesize)
+ pos += bbm_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ memcpy(oob, dma_buf + pos, len);
+ oob += len;
+ if (len < ecc_bytes) {
+ len = ecc_bytes - len;
+ memcpy(oob, dma_buf + writesize + bbm_skip,
+ len);
+ oob += len;
+ }
+ }
+
+ /* OOB free */
+ len = oobsize - (oob - chip->oob_poi);
+ memcpy(oob, dma_buf + size - len, len);
+ }
+
+ return 0;
}
static int denali_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
int page)
{
- read_oob_data(mtd, chip->oob_poi, page);
+ denali_oob_xfer(mtd, chip, page, 0);
return 0;
}
-static int denali_read_page(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf, int oob_required, int page)
+static int denali_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
- dma_addr_t addr = denali->buf.dma_buf;
- size_t size = mtd->writesize + mtd->oobsize;
- uint32_t irq_status;
- uint32_t irq_mask = denali->caps & DENALI_CAP_HW_ECC_FIXUP ?
- INTR__DMA_CMD_COMP | INTR__ECC_UNCOR_ERR :
- INTR__ECC_TRANSACTION_DONE | INTR__ECC_ERR;
- unsigned long uncor_ecc_flags = 0;
- int stat = 0;
-
- if (page != denali->page) {
- dev_err(denali->dev,
- "IN %s: page %d is not equal to denali->page %d",
- __func__, page, denali->page);
- BUG();
- }
+ int status;
- setup_ecc_for_xfer(denali, true, false);
+ denali_reset_irq(denali);
- denali_enable_dma(denali, true);
- dma_sync_single_for_device(denali->dev, addr, size, DMA_FROM_DEVICE);
+ denali_oob_xfer(mtd, chip, page, 1);
- clear_interrupts(denali);
- denali_setup_dma(denali, DENALI_READ);
+ chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+ status = chip->waitfunc(mtd, chip);
- /* wait for operation to complete */
- irq_status = wait_for_irq(denali, irq_mask);
+ return status & NAND_STATUS_FAIL ? -EIO : 0;
+}
- dma_sync_single_for_cpu(denali->dev, addr, size, DMA_FROM_DEVICE);
+static int denali_read_page(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ unsigned long uncor_ecc_flags = 0;
+ int stat = 0;
+ int ret;
- memcpy(buf, denali->buf.buf, mtd->writesize);
+ ret = denali_data_xfer(denali, buf, mtd->writesize, page, 0, 0);
+ if (ret && ret != -EBADMSG)
+ return ret;
if (denali->caps & DENALI_CAP_HW_ECC_FIXUP)
stat = denali_hw_ecc_fixup(mtd, denali, &uncor_ecc_flags);
- else if (irq_status & INTR__ECC_ERR)
+ else if (ret == -EBADMSG)
stat = denali_sw_ecc_fixup(mtd, denali, &uncor_ecc_flags, buf);
- denali_enable_dma(denali, false);
if (stat < 0)
return stat;
if (uncor_ecc_flags) {
- read_oob_data(mtd, chip->oob_poi, denali->page);
+ ret = denali_read_oob(mtd, chip, page);
+ if (ret)
+ return ret;
stat = denali_check_erased_page(mtd, chip, buf,
uncor_ecc_flags, stat);
@@ -1181,137 +892,268 @@ static int denali_read_page(struct mtd_info *mtd, struct nand_chip *chip,
return stat;
}
-static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf, int oob_required, int page)
+static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required, int page)
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
- dma_addr_t addr = denali->buf.dma_buf;
- size_t size = mtd->writesize + mtd->oobsize;
- uint32_t irq_mask = INTR__DMA_CMD_COMP;
-
- if (page != denali->page) {
- dev_err(denali->dev,
- "IN %s: page %d is not equal to denali->page %d",
- __func__, page, denali->page);
- BUG();
- }
-
- setup_ecc_for_xfer(denali, false, true);
- denali_enable_dma(denali, true);
-
- dma_sync_single_for_device(denali->dev, addr, size, DMA_FROM_DEVICE);
-
- clear_interrupts(denali);
- denali_setup_dma(denali, DENALI_READ);
-
- /* wait for operation to complete */
- wait_for_irq(denali, irq_mask);
+ int writesize = mtd->writesize;
+ int oobsize = mtd->oobsize;
+ int ecc_steps = chip->ecc.steps;
+ int ecc_size = chip->ecc.size;
+ int ecc_bytes = chip->ecc.bytes;
+ void *dma_buf = denali->buf;
+ int bbm_skip = denali->bbtskipbytes;
+ size_t size = writesize + oobsize;
+ int i, pos, len;
- dma_sync_single_for_cpu(denali->dev, addr, size, DMA_FROM_DEVICE);
+ /*
+ * Fill the buffer with 0xff first except the full page transfer.
+ * This simplifies the logic.
+ */
+ if (!buf || !oob_required)
+ memset(dma_buf, 0xff, size);
+
+ /* Arrange the buffer for syndrome payload/ecc layout */
+ if (buf) {
+ for (i = 0; i < ecc_steps; i++) {
+ pos = i * (ecc_size + ecc_bytes);
+ len = ecc_size;
+
+ if (pos >= writesize)
+ pos += bbm_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ memcpy(dma_buf + pos, buf, len);
+ buf += len;
+ if (len < ecc_size) {
+ len = ecc_size - len;
+ memcpy(dma_buf + writesize + bbm_skip, buf,
+ len);
+ buf += len;
+ }
+ }
+ }
- denali_enable_dma(denali, false);
+ if (oob_required) {
+ const uint8_t *oob = chip->oob_poi;
+
+ /* BBM at the beginning of the OOB area */
+ memcpy(dma_buf + writesize, oob, bbm_skip);
+ oob += bbm_skip;
+
+ /* OOB ECC */
+ for (i = 0; i < ecc_steps; i++) {
+ pos = ecc_size + i * (ecc_size + ecc_bytes);
+ len = ecc_bytes;
+
+ if (pos >= writesize)
+ pos += bbm_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ memcpy(dma_buf + pos, oob, len);
+ oob += len;
+ if (len < ecc_bytes) {
+ len = ecc_bytes - len;
+ memcpy(dma_buf + writesize + bbm_skip, oob,
+ len);
+ oob += len;
+ }
+ }
- memcpy(buf, denali->buf.buf, mtd->writesize);
- memcpy(chip->oob_poi, denali->buf.buf + mtd->writesize, mtd->oobsize);
+ /* OOB free */
+ len = oobsize - (oob - chip->oob_poi);
+ memcpy(dma_buf + size - len, oob, len);
+ }
- return 0;
+ return denali_data_xfer(denali, dma_buf, size, page, 1, 1);
}
-static uint8_t denali_read_byte(struct mtd_info *mtd)
+static int denali_write_page(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required, int page)
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
- uint8_t result = 0xff;
- if (denali->buf.head < denali->buf.tail)
- result = denali->buf.buf[denali->buf.head++];
-
- return result;
+ return denali_data_xfer(denali, (void *)buf, mtd->writesize,
+ page, 0, 1);
}
static void denali_select_chip(struct mtd_info *mtd, int chip)
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
- spin_lock_irq(&denali->irq_lock);
denali->flash_bank = chip;
- spin_unlock_irq(&denali->irq_lock);
}
static int denali_waitfunc(struct mtd_info *mtd, struct nand_chip *chip)
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
- int status = denali->status;
+ uint32_t irq_status;
- denali->status = 0;
+ /* R/B# pin transitioned from low to high? */
+ irq_status = denali_wait_for_irq(denali, INTR__INT_ACT);
- return status;
+ return irq_status & INTR__INT_ACT ? 0 : NAND_STATUS_FAIL;
}
static int denali_erase(struct mtd_info *mtd, int page)
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
-
uint32_t cmd, irq_status;
- clear_interrupts(denali);
+ denali_reset_irq(denali);
/* setup page read request for access type */
cmd = MODE_10 | BANK(denali->flash_bank) | page;
index_addr(denali, cmd, 0x1);
/* wait for erase to complete or failure to occur */
- irq_status = wait_for_irq(denali, INTR__ERASE_COMP | INTR__ERASE_FAIL);
+ irq_status = denali_wait_for_irq(denali,
+ INTR__ERASE_COMP | INTR__ERASE_FAIL);
- return irq_status & INTR__ERASE_FAIL ? NAND_STATUS_FAIL : PASS;
+ return irq_status & INTR__ERASE_COMP ? 0 : NAND_STATUS_FAIL;
}
-static void denali_cmdfunc(struct mtd_info *mtd, unsigned int cmd, int col,
- int page)
+#define DIV_ROUND_DOWN_ULL(ll, d) \
+ ({ unsigned long long _tmp = (ll); do_div(_tmp, d); _tmp; })
+
+static int denali_setup_data_interface(struct mtd_info *mtd,
+ const struct nand_data_interface *conf,
+ bool check_only)
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
- uint32_t addr, id;
+ const struct nand_sdr_timings *timings;
+ unsigned long t_clk;
+ int acc_clks, re_2_we, re_2_re, we_2_re, addr_2_data;
+ int rdwr_en_lo, rdwr_en_hi, rdwr_en_lo_hi, cs_setup;
+ int addr_2_data_mask;
+ uint32_t tmp;
+
+ timings = nand_get_sdr_timings(conf);
+ if (IS_ERR(timings))
+ return PTR_ERR(timings);
+
+ /* clk_x period in picoseconds */
+ t_clk = DIV_ROUND_DOWN_ULL(1000000000000ULL, denali->clk_x_rate);
+ if (!t_clk)
+ return -EINVAL;
+
+ if (check_only)
+ return 0;
+
+ /* tREA -> ACC_CLKS */
+ acc_clks = DIV_ROUND_UP(timings->tREA_max, t_clk);
+ acc_clks = min_t(int, acc_clks, ACC_CLKS__VALUE);
+
+ tmp = ioread32(denali->flash_reg + ACC_CLKS);
+ tmp &= ~ACC_CLKS__VALUE;
+ tmp |= acc_clks;
+ iowrite32(tmp, denali->flash_reg + ACC_CLKS);
+
+ /* tRWH -> RE_2_WE */
+ re_2_we = DIV_ROUND_UP(timings->tRHW_min, t_clk);
+ re_2_we = min_t(int, re_2_we, RE_2_WE__VALUE);
+
+ tmp = ioread32(denali->flash_reg + RE_2_WE);
+ tmp &= ~RE_2_WE__VALUE;
+ tmp |= re_2_we;
+ iowrite32(tmp, denali->flash_reg + RE_2_WE);
+
+ /* tRHZ -> RE_2_RE */
+ re_2_re = DIV_ROUND_UP(timings->tRHZ_max, t_clk);
+ re_2_re = min_t(int, re_2_re, RE_2_RE__VALUE);
+
+ tmp = ioread32(denali->flash_reg + RE_2_RE);
+ tmp &= ~RE_2_RE__VALUE;
+ tmp |= re_2_re;
+ iowrite32(tmp, denali->flash_reg + RE_2_RE);
+
+ /* tWHR -> WE_2_RE */
+ we_2_re = DIV_ROUND_UP(timings->tWHR_min, t_clk);
+ we_2_re = min_t(int, we_2_re, TWHR2_AND_WE_2_RE__WE_2_RE);
+
+ tmp = ioread32(denali->flash_reg + TWHR2_AND_WE_2_RE);
+ tmp &= ~TWHR2_AND_WE_2_RE__WE_2_RE;
+ tmp |= we_2_re;
+ iowrite32(tmp, denali->flash_reg + TWHR2_AND_WE_2_RE);
+
+ /* tADL -> ADDR_2_DATA */
+
+ /* for older versions, ADDR_2_DATA is only 6 bit wide */
+ addr_2_data_mask = TCWAW_AND_ADDR_2_DATA__ADDR_2_DATA;
+ if (denali->revision < 0x0501)
+ addr_2_data_mask >>= 1;
+
+ addr_2_data = DIV_ROUND_UP(timings->tADL_min, t_clk);
+ addr_2_data = min_t(int, addr_2_data, addr_2_data_mask);
+
+ tmp = ioread32(denali->flash_reg + TCWAW_AND_ADDR_2_DATA);
+ tmp &= ~addr_2_data_mask;
+ tmp |= addr_2_data;
+ iowrite32(tmp, denali->flash_reg + TCWAW_AND_ADDR_2_DATA);
+
+ /* tREH, tWH -> RDWR_EN_HI_CNT */
+ rdwr_en_hi = DIV_ROUND_UP(max(timings->tREH_min, timings->tWH_min),
+ t_clk);
+ rdwr_en_hi = min_t(int, rdwr_en_hi, RDWR_EN_HI_CNT__VALUE);
+
+ tmp = ioread32(denali->flash_reg + RDWR_EN_HI_CNT);
+ tmp &= ~RDWR_EN_HI_CNT__VALUE;
+ tmp |= rdwr_en_hi;
+ iowrite32(tmp, denali->flash_reg + RDWR_EN_HI_CNT);
+
+ /* tRP, tWP -> RDWR_EN_LO_CNT */
+ rdwr_en_lo = DIV_ROUND_UP(max(timings->tRP_min, timings->tWP_min),
+ t_clk);
+ rdwr_en_lo_hi = DIV_ROUND_UP(max(timings->tRC_min, timings->tWC_min),
+ t_clk);
+ rdwr_en_lo_hi = max(rdwr_en_lo_hi, DENALI_CLK_X_MULT);
+ rdwr_en_lo = max(rdwr_en_lo, rdwr_en_lo_hi - rdwr_en_hi);
+ rdwr_en_lo = min_t(int, rdwr_en_lo, RDWR_EN_LO_CNT__VALUE);
+
+ tmp = ioread32(denali->flash_reg + RDWR_EN_LO_CNT);
+ tmp &= ~RDWR_EN_LO_CNT__VALUE;
+ tmp |= rdwr_en_lo;
+ iowrite32(tmp, denali->flash_reg + RDWR_EN_LO_CNT);
+
+ /* tCS, tCEA -> CS_SETUP_CNT */
+ cs_setup = max3((int)DIV_ROUND_UP(timings->tCS_min, t_clk) - rdwr_en_lo,
+ (int)DIV_ROUND_UP(timings->tCEA_max, t_clk) - acc_clks,
+ 0);
+ cs_setup = min_t(int, cs_setup, CS_SETUP_CNT__VALUE);
+
+ tmp = ioread32(denali->flash_reg + CS_SETUP_CNT);
+ tmp &= ~CS_SETUP_CNT__VALUE;
+ tmp |= cs_setup;
+ iowrite32(tmp, denali->flash_reg + CS_SETUP_CNT);
+
+ return 0;
+}
+
+static void denali_reset_banks(struct denali_nand_info *denali)
+{
+ u32 irq_status;
int i;
- switch (cmd) {
- case NAND_CMD_PAGEPROG:
- break;
- case NAND_CMD_STATUS:
- read_status(denali);
- break;
- case NAND_CMD_READID:
- case NAND_CMD_PARAM:
- reset_buf(denali);
- /*
- * sometimes ManufactureId read from register is not right
- * e.g. some of Micron MT29F32G08QAA MLC NAND chips
- * So here we send READID cmd to NAND insteand
- */
- addr = MODE_11 | BANK(denali->flash_bank);
- index_addr(denali, addr | 0, 0x90);
- index_addr(denali, addr | 1, col);
- for (i = 0; i < 8; i++) {
- index_addr_read_data(denali, addr | 2, &id);
- write_byte_to_buf(denali, id);
- }
- break;
- case NAND_CMD_READ0:
- case NAND_CMD_SEQIN:
- denali->page = page;
- break;
- case NAND_CMD_RESET:
- reset_bank(denali);
- break;
- case NAND_CMD_READOOB:
- /* TODO: Read OOB data */
- break;
- default:
- pr_err(": unsupported command received 0x%x\n", cmd);
- break;
+ for (i = 0; i < denali->max_banks; i++) {
+ denali->flash_bank = i;
+
+ denali_reset_irq(denali);
+
+ iowrite32(DEVICE_RESET__BANK(i),
+ denali->flash_reg + DEVICE_RESET);
+
+ irq_status = denali_wait_for_irq(denali,
+ INTR__RST_COMP | INTR__INT_ACT | INTR__TIME_OUT);
+ if (!(irq_status & INTR__INT_ACT))
+ break;
}
+
+ dev_dbg(denali->dev, "%d chips connected\n", i);
+ denali->max_banks = i;
}
-/* end NAND core entry points */
-/* Initialization code to bring the device up to a known good state */
static void denali_hw_init(struct denali_nand_info *denali)
{
/*
@@ -1331,7 +1173,6 @@ static void denali_hw_init(struct denali_nand_info *denali)
denali->bbtskipbytes = ioread32(denali->flash_reg +
SPARE_AREA_SKIP_BYTES);
detect_max_banks(denali);
- denali_nand_reset(denali);
iowrite32(0x0F, denali->flash_reg + RB_PIN_ENABLED);
iowrite32(CHIP_EN_DONT_CARE__FLAG,
denali->flash_reg + CHIP_ENABLE_DONT_CARE);
@@ -1341,17 +1182,25 @@ static void denali_hw_init(struct denali_nand_info *denali)
/* Should set value for these registers when init */
iowrite32(0, denali->flash_reg + TWO_ROW_ADDR_CYCLES);
iowrite32(1, denali->flash_reg + ECC_ENABLE);
- denali_nand_timing_set(denali);
- denali_irq_init(denali);
}
-/*
- * Althogh controller spec said SLC ECC is forceb to be 4bit,
- * but denali controller in MRST only support 15bit and 8bit ECC
- * correction
- */
-#define ECC_8BITS 14
-#define ECC_15BITS 26
+static int denali_calc_ecc_bytes(const struct nand_ecc_setting *setting)
+{
+ int coef;
+
+ switch (setting->step) {
+ case 512:
+ coef = 13;
+ break;
+ case 1024:
+ coef = 14;
+ break;
+ default:
+ return -ENOTSUPP;
+ }
+
+ return DIV_ROUND_UP(setting->strength * coef, 16) * 2;
+}
static int denali_ooblayout_ecc(struct mtd_info *mtd, int section,
struct mtd_oob_region *oobregion)
@@ -1388,29 +1237,6 @@ static const struct mtd_ooblayout_ops denali_ooblayout_ops = {
.free = denali_ooblayout_free,
};
-static uint8_t bbt_pattern[] = {'B', 'b', 't', '0' };
-static uint8_t mirror_pattern[] = {'1', 't', 'b', 'B' };
-
-static struct nand_bbt_descr bbt_main_descr = {
- .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
- | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
- .offs = 8,
- .len = 4,
- .veroffs = 12,
- .maxblocks = 4,
- .pattern = bbt_pattern,
-};
-
-static struct nand_bbt_descr bbt_mirror_descr = {
- .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
- | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
- .offs = 8,
- .len = 4,
- .veroffs = 12,
- .maxblocks = 4,
- .pattern = mirror_pattern,
-};
-
/* initialize driver data structures */
static void denali_drv_init(struct denali_nand_info *denali)
{
@@ -1425,12 +1251,6 @@ static void denali_drv_init(struct denali_nand_info *denali)
* element that might be access shared data (interrupt status)
*/
spin_lock_init(&denali->irq_lock);
-
- /* indicate that MTD has not selected a valid bank yet */
- denali->flash_bank = CHIP_SELECT_INVALID;
-
- /* initialize our irq_status variable to indicate no interrupts */
- denali->irq_status = 0;
}
static int denali_multidev_fixup(struct denali_nand_info *denali)
@@ -1488,29 +1308,15 @@ int denali_init(struct denali_nand_info *denali)
{
struct nand_chip *chip = &denali->nand;
struct mtd_info *mtd = nand_to_mtd(chip);
+ struct nand_ecc_engine_caps ecc_engine_caps;
int ret;
- if (denali->platform == INTEL_CE4100) {
- /*
- * Due to a silicon limitation, we can only support
- * ONFI timing mode 1 and below.
- */
- if (onfi_timing_mode < -1 || onfi_timing_mode > 1) {
- pr_err("Intel CE4100 only supports ONFI timing mode 1 or below\n");
- return -EINVAL;
- }
- }
-
- /* allocate a temporary buffer for nand_scan_ident() */
- denali->buf.buf = devm_kzalloc(denali->dev, PAGE_SIZE,
- GFP_DMA | GFP_KERNEL);
- if (!denali->buf.buf)
- return -ENOMEM;
-
mtd->dev.parent = denali->dev;
denali_hw_init(denali);
denali_drv_init(denali);
+ denali_clear_irq_all(denali);
+
/* Request IRQ after all the hardware initialization is finished */
ret = devm_request_irq(denali->dev, denali->irq, denali_isr,
IRQF_SHARED, DENALI_NAND_NAME, denali);
@@ -1519,8 +1325,11 @@ int denali_init(struct denali_nand_info *denali)
return ret;
}
- /* now that our ISR is registered, we can enable interrupts */
- denali_set_intr_modes(denali, true);
+ denali_enable_irq(denali);
+ denali_reset_banks(denali);
+
+ denali->flash_bank = CHIP_SELECT_INVALID;
+
nand_set_flash_node(chip, denali->dev->of_node);
/* Fallback to the default name if DT did not give "label" property */
if (!mtd->name)
@@ -1528,9 +1337,14 @@ int denali_init(struct denali_nand_info *denali)
/* register the driver with the NAND core subsystem */
chip->select_chip = denali_select_chip;
- chip->cmdfunc = denali_cmdfunc;
chip->read_byte = denali_read_byte;
+ chip->write_byte = denali_write_byte;
+ chip->cmd_ctrl = denali_cmd_ctrl;
+ chip->dev_ready = denali_dev_ready;
chip->waitfunc = denali_waitfunc;
+ /* clk rate info is needed for setup_data_interface */
+ if (denali->clk_x_rate)
+ chip->setup_data_interface = denali_setup_data_interface;
/*
* scan for NAND devices attached to the controller
@@ -1539,33 +1353,24 @@ int denali_init(struct denali_nand_info *denali)
*/
ret = nand_scan_ident(mtd, denali->max_banks, NULL);
if (ret)
- goto failed_req_irq;
-
- /* allocate the right size buffer now */
- devm_kfree(denali->dev, denali->buf.buf);
- denali->buf.buf = devm_kzalloc(denali->dev,
- mtd->writesize + mtd->oobsize,
- GFP_KERNEL);
- if (!denali->buf.buf) {
- ret = -ENOMEM;
- goto failed_req_irq;
- }
+ goto disable_irq;
- ret = dma_set_mask(denali->dev,
- DMA_BIT_MASK(denali->caps & DENALI_CAP_DMA_64BIT ?
- 64 : 32));
- if (ret) {
- dev_err(denali->dev, "No usable DMA configuration\n");
- goto failed_req_irq;
+ if (ioread32(denali->flash_reg + FEATURES) & FEATURES__DMA)
+ denali->dma_avail = 1;
+
+ if (denali->dma_avail) {
+ int dma_bit = denali->caps & DENALI_CAP_DMA_64BIT ? 64 : 32;
+
+ ret = dma_set_mask(denali->dev, DMA_BIT_MASK(dma_bit));
+ if (ret) {
+ dev_info(denali->dev, "Failed to set DMA mask. Disabling DMA.\n");
+ denali->dma_avail = 0;
+ }
}
- denali->buf.dma_buf = dma_map_single(denali->dev, denali->buf.buf,
- mtd->writesize + mtd->oobsize,
- DMA_BIDIRECTIONAL);
- if (dma_mapping_error(denali->dev, denali->buf.dma_buf)) {
- dev_err(denali->dev, "Failed to map DMA buffer\n");
- ret = -EIO;
- goto failed_req_irq;
+ if (denali->dma_avail) {
+ chip->options |= NAND_USE_BOUNCE_BUFFER;
+ chip->buf_align = 16;
}
/*
@@ -1574,46 +1379,74 @@ int denali_init(struct denali_nand_info *denali)
* bad block management.
*/
- /* Bad block management */
- chip->bbt_td = &bbt_main_descr;
- chip->bbt_md = &bbt_mirror_descr;
-
- /* skip the scan for now until we have OOB read and write support */
chip->bbt_options |= NAND_BBT_USE_FLASH;
- chip->options |= NAND_SKIP_BBTSCAN;
+ chip->bbt_options |= NAND_BBT_NO_OOB;
+
chip->ecc.mode = NAND_ECC_HW_SYNDROME;
/* no subpage writes on denali */
chip->options |= NAND_NO_SUBPAGE_WRITE;
+ ecc_engine_caps.ecc_settings = denali->avail_ecc_settings;
+ ecc_engine_caps.calc_ecc_bytes = denali_calc_ecc_bytes;
+ ecc_engine_caps.avail_oobsize = mtd->oobsize - denali->bbtskipbytes;
+
+ ret = -ENOTSUPP;
+
+ /* If both .size and .strength are set (by DT), we check if supported */
+ ret = nand_check_ecc_caps(mtd, chip, &ecc_engine_caps);
+ if (ret && ret != -ENODATA)
+ dev_info(denali->dev, "try to find other ECC settings\n");
+
/*
- * Denali Controller only support 15bit and 8bit ECC in MRST,
- * so just let controller do 15bit ECC for MLC and 8bit ECC for
- * SLC if possible.
- * */
- if (!nand_is_slc(chip) &&
- (mtd->oobsize > (denali->bbtskipbytes +
- ECC_15BITS * (mtd->writesize /
- ECC_SECTOR_SIZE)))) {
- /* if MLC OOB size is large enough, use 15bit ECC*/
- chip->ecc.strength = 15;
- chip->ecc.bytes = ECC_15BITS;
- iowrite32(15, denali->flash_reg + ECC_CORRECTION);
- } else if (mtd->oobsize < (denali->bbtskipbytes +
- ECC_8BITS * (mtd->writesize /
- ECC_SECTOR_SIZE))) {
- pr_err("Your NAND chip OOB is not large enough to contain 8bit ECC correction codes");
- goto failed_req_irq;
- } else {
- chip->ecc.strength = 8;
- chip->ecc.bytes = ECC_8BITS;
- iowrite32(8, denali->flash_reg + ECC_CORRECTION);
+ * We want .size and .strength closest to the chip's requirement
+ * unless NAND_ECC_MAXIMIZE is requested.
+ */
+ if (ret && !(chip->ecc.options & NAND_ECC_MAXIMIZE)) {
+ ret = nand_try_to_match_ecc_req(mtd, chip, &ecc_engine_caps);
+ if (ret)
+ dev_info(denali->dev, "try to maximize ECC setting\n");
}
+ /* The last thing we can do is to try the max ECC strength */
+ if (ret)
+ ret = nand_try_to_maximize_ecc(mtd, chip, &ecc_engine_caps);
+
+ if (ret) {
+ dev_err(denali->dev, "failed to choose ECC size/strength\n");
+ goto disable_irq;
+ }
+
+ dev_dbg(denali->dev,
+ "chosen ECC settings: step=%d, strength=%d, bytes=%d\n",
+ chip->ecc.size, chip->ecc.strength, chip->ecc.bytes);
+
+ iowrite32(MAKE_ECC_CORRECTION(chip->ecc.strength,
+ chip->ecc.strength + 1),
+ denali->flash_reg + ECC_CORRECTION);
+ iowrite32(mtd->erasesize / mtd->writesize,
+ denali->flash_reg + PAGES_PER_BLOCK);
+ iowrite32(denali->nand.options & NAND_BUSWIDTH_16 ? 1 : 0,
+ denali->flash_reg + DEVICE_WIDTH);
+ iowrite32(mtd->writesize, denali->flash_reg + DEVICE_MAIN_AREA_SIZE);
+ iowrite32(mtd->oobsize, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
+
+ iowrite32(chip->ecc.size, denali->flash_reg + CFG_DATA_BLOCK_SIZE);
+ iowrite32(chip->ecc.size, denali->flash_reg + CFG_LAST_DATA_BLOCK_SIZE);
+ /* chip->ecc.steps is set by nand_scan_tail(); not available here */
+ iowrite32(mtd->writesize / chip->ecc.size,
+ denali->flash_reg + CFG_NUM_DATA_BLOCKS);
+
mtd_set_ooblayout(mtd, &denali_ooblayout_ops);
- /* override the default read operations */
- chip->ecc.size = ECC_SECTOR_SIZE;
+ if (denali->nand.options & NAND_BUSWIDTH_16) {
+ chip->read_buf = denali_read_buf16;
+ chip->write_buf = denali_write_buf16;
+ } else {
+ chip->read_buf = denali_read_buf;
+ chip->write_buf = denali_write_buf;
+ }
+ chip->ecc.options |= NAND_ECC_CUSTOM_PAGE_ACCESS;
chip->ecc.read_page = denali_read_page;
chip->ecc.read_page_raw = denali_read_page_raw;
chip->ecc.write_page = denali_write_page;
@@ -1624,21 +1457,34 @@ int denali_init(struct denali_nand_info *denali)
ret = denali_multidev_fixup(denali);
if (ret)
- goto failed_req_irq;
+ goto disable_irq;
+
+ /*
+ * This buffer is DMA-mapped by denali_{read,write}_page_raw. Do not
+ * use devm_kmalloc() because the memory allocated by devm_ does not
+ * guarantee DMA-safe alignment.
+ */
+ denali->buf = kmalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL);
+ if (!denali->buf) {
+ ret = -ENOMEM;
+ goto disable_irq;
+ }
ret = nand_scan_tail(mtd);
if (ret)
- goto failed_req_irq;
+ goto free_buf;
ret = mtd_device_register(mtd, NULL, 0);
if (ret) {
dev_err(denali->dev, "Failed to register MTD: %d\n", ret);
- goto failed_req_irq;
+ goto free_buf;
}
return 0;
-failed_req_irq:
- denali_irq_cleanup(denali->irq, denali);
+free_buf:
+ kfree(denali->buf);
+disable_irq:
+ denali_disable_irq(denali);
return ret;
}
@@ -1656,8 +1502,9 @@ void denali_remove(struct denali_nand_info *denali)
int bufsize = mtd->writesize + mtd->oobsize;
nand_release(mtd);
- denali_irq_cleanup(denali->irq, denali);
- dma_unmap_single(denali->dev, denali->buf.dma_buf, bufsize,
+ kfree(denali->buf);
+ denali_disable_irq(denali);
+ dma_unmap_single(denali->dev, denali->dma_addr, bufsize,
DMA_BIDIRECTIONAL);
}
EXPORT_SYMBOL(denali_remove);
@@ -24,325 +24,318 @@
#include <linux/mtd/nand.h>
#define DEVICE_RESET 0x0
-#define DEVICE_RESET__BANK0 0x0001
-#define DEVICE_RESET__BANK1 0x0002
-#define DEVICE_RESET__BANK2 0x0004
-#define DEVICE_RESET__BANK3 0x0008
+#define DEVICE_RESET__BANK(bank) BIT(bank)
#define TRANSFER_SPARE_REG 0x10
-#define TRANSFER_SPARE_REG__FLAG 0x0001
+#define TRANSFER_SPARE_REG__FLAG BIT(0)
#define LOAD_WAIT_CNT 0x20
-#define LOAD_WAIT_CNT__VALUE 0xffff
+#define LOAD_WAIT_CNT__VALUE GENMASK(15, 0)
#define PROGRAM_WAIT_CNT 0x30
-#define PROGRAM_WAIT_CNT__VALUE 0xffff
+#define PROGRAM_WAIT_CNT__VALUE GENMASK(15, 0)
#define ERASE_WAIT_CNT 0x40
-#define ERASE_WAIT_CNT__VALUE 0xffff
+#define ERASE_WAIT_CNT__VALUE GENMASK(15, 0)
#define INT_MON_CYCCNT 0x50
-#define INT_MON_CYCCNT__VALUE 0xffff
+#define INT_MON_CYCCNT__VALUE GENMASK(15, 0)
#define RB_PIN_ENABLED 0x60
-#define RB_PIN_ENABLED__BANK0 0x0001
-#define RB_PIN_ENABLED__BANK1 0x0002
-#define RB_PIN_ENABLED__BANK2 0x0004
-#define RB_PIN_ENABLED__BANK3 0x0008
+#define RB_PIN_ENABLED__BANK(bank) BIT(bank)
#define MULTIPLANE_OPERATION 0x70
-#define MULTIPLANE_OPERATION__FLAG 0x0001
+#define MULTIPLANE_OPERATION__FLAG BIT(0)
#define MULTIPLANE_READ_ENABLE 0x80
-#define MULTIPLANE_READ_ENABLE__FLAG 0x0001
+#define MULTIPLANE_READ_ENABLE__FLAG BIT(0)
#define COPYBACK_DISABLE 0x90
-#define COPYBACK_DISABLE__FLAG 0x0001
+#define COPYBACK_DISABLE__FLAG BIT(0)
#define CACHE_WRITE_ENABLE 0xa0
-#define CACHE_WRITE_ENABLE__FLAG 0x0001
+#define CACHE_WRITE_ENABLE__FLAG BIT(0)
#define CACHE_READ_ENABLE 0xb0
-#define CACHE_READ_ENABLE__FLAG 0x0001
+#define CACHE_READ_ENABLE__FLAG BIT(0)
#define PREFETCH_MODE 0xc0
-#define PREFETCH_MODE__PREFETCH_EN 0x0001
-#define PREFETCH_MODE__PREFETCH_BURST_LENGTH 0xfff0
+#define PREFETCH_MODE__PREFETCH_EN BIT(0)
+#define PREFETCH_MODE__PREFETCH_BURST_LENGTH GENMASK(15, 4)
#define CHIP_ENABLE_DONT_CARE 0xd0
-#define CHIP_EN_DONT_CARE__FLAG 0x01
+#define CHIP_EN_DONT_CARE__FLAG BIT(0)
#define ECC_ENABLE 0xe0
-#define ECC_ENABLE__FLAG 0x0001
+#define ECC_ENABLE__FLAG BIT(0)
#define GLOBAL_INT_ENABLE 0xf0
-#define GLOBAL_INT_EN_FLAG 0x01
+#define GLOBAL_INT_EN_FLAG BIT(0)
-#define WE_2_RE 0x100
-#define WE_2_RE__VALUE 0x003f
+#define TWHR2_AND_WE_2_RE 0x100
+#define TWHR2_AND_WE_2_RE__WE_2_RE GENMASK(5, 0)
+#define TWHR2_AND_WE_2_RE__TWHR2 GENMASK(13, 8)
-#define ADDR_2_DATA 0x110
-#define ADDR_2_DATA__VALUE 0x003f
+#define TCWAW_AND_ADDR_2_DATA 0x110
+/* The width of ADDR_2_DATA is 6 bit for old IP, 7 bit for new IP */
+#define TCWAW_AND_ADDR_2_DATA__ADDR_2_DATA GENMASK(6, 0)
+#define TCWAW_AND_ADDR_2_DATA__TCWAW GENMASK(13, 8)
#define RE_2_WE 0x120
-#define RE_2_WE__VALUE 0x003f
+#define RE_2_WE__VALUE GENMASK(5, 0)
#define ACC_CLKS 0x130
-#define ACC_CLKS__VALUE 0x000f
+#define ACC_CLKS__VALUE GENMASK(3, 0)
#define NUMBER_OF_PLANES 0x140
-#define NUMBER_OF_PLANES__VALUE 0x0007
+#define NUMBER_OF_PLANES__VALUE GENMASK(2, 0)
#define PAGES_PER_BLOCK 0x150
-#define PAGES_PER_BLOCK__VALUE 0xffff
+#define PAGES_PER_BLOCK__VALUE GENMASK(15, 0)
#define DEVICE_WIDTH 0x160
-#define DEVICE_WIDTH__VALUE 0x0003
+#define DEVICE_WIDTH__VALUE GENMASK(1, 0)
#define DEVICE_MAIN_AREA_SIZE 0x170
-#define DEVICE_MAIN_AREA_SIZE__VALUE 0xffff
+#define DEVICE_MAIN_AREA_SIZE__VALUE GENMASK(15, 0)
#define DEVICE_SPARE_AREA_SIZE 0x180
-#define DEVICE_SPARE_AREA_SIZE__VALUE 0xffff
+#define DEVICE_SPARE_AREA_SIZE__VALUE GENMASK(15, 0)
#define TWO_ROW_ADDR_CYCLES 0x190
-#define TWO_ROW_ADDR_CYCLES__FLAG 0x0001
+#define TWO_ROW_ADDR_CYCLES__FLAG BIT(0)
#define MULTIPLANE_ADDR_RESTRICT 0x1a0
-#define MULTIPLANE_ADDR_RESTRICT__FLAG 0x0001
+#define MULTIPLANE_ADDR_RESTRICT__FLAG BIT(0)
#define ECC_CORRECTION 0x1b0
-#define ECC_CORRECTION__VALUE 0x001f
+#define ECC_CORRECTION__VALUE GENMASK(4, 0)
+#define ECC_CORRECTION__ERASE_THRESHOLD GENMASK(31, 16)
+#define MAKE_ECC_CORRECTION(val, thresh) \
+ (((val) & (ECC_CORRECTION__VALUE)) | \
+ (((thresh) << 16) & (ECC_CORRECTION__ERASE_THRESHOLD)))
#define READ_MODE 0x1c0
-#define READ_MODE__VALUE 0x000f
+#define READ_MODE__VALUE GENMASK(3, 0)
#define WRITE_MODE 0x1d0
-#define WRITE_MODE__VALUE 0x000f
+#define WRITE_MODE__VALUE GENMASK(3, 0)
#define COPYBACK_MODE 0x1e0
-#define COPYBACK_MODE__VALUE 0x000f
+#define COPYBACK_MODE__VALUE GENMASK(3, 0)
#define RDWR_EN_LO_CNT 0x1f0
-#define RDWR_EN_LO_CNT__VALUE 0x001f
+#define RDWR_EN_LO_CNT__VALUE GENMASK(4, 0)
#define RDWR_EN_HI_CNT 0x200
-#define RDWR_EN_HI_CNT__VALUE 0x001f
+#define RDWR_EN_HI_CNT__VALUE GENMASK(4, 0)
#define MAX_RD_DELAY 0x210
-#define MAX_RD_DELAY__VALUE 0x000f
+#define MAX_RD_DELAY__VALUE GENMASK(3, 0)
#define CS_SETUP_CNT 0x220
-#define CS_SETUP_CNT__VALUE 0x001f
+#define CS_SETUP_CNT__VALUE GENMASK(4, 0)
+#define CS_SETUP_CNT__TWB GENMASK(17, 12)
#define SPARE_AREA_SKIP_BYTES 0x230
-#define SPARE_AREA_SKIP_BYTES__VALUE 0x003f
+#define SPARE_AREA_SKIP_BYTES__VALUE GENMASK(5, 0)
#define SPARE_AREA_MARKER 0x240
-#define SPARE_AREA_MARKER__VALUE 0xffff
+#define SPARE_AREA_MARKER__VALUE GENMASK(15, 0)
#define DEVICES_CONNECTED 0x250
-#define DEVICES_CONNECTED__VALUE 0x0007
+#define DEVICES_CONNECTED__VALUE GENMASK(2, 0)
#define DIE_MASK 0x260
-#define DIE_MASK__VALUE 0x00ff
+#define DIE_MASK__VALUE GENMASK(7, 0)
#define FIRST_BLOCK_OF_NEXT_PLANE 0x270
-#define FIRST_BLOCK_OF_NEXT_PLANE__VALUE 0xffff
+#define FIRST_BLOCK_OF_NEXT_PLANE__VALUE GENMASK(15, 0)
#define WRITE_PROTECT 0x280
-#define WRITE_PROTECT__FLAG 0x0001
+#define WRITE_PROTECT__FLAG BIT(0)
#define RE_2_RE 0x290
-#define RE_2_RE__VALUE 0x003f
+#define RE_2_RE__VALUE GENMASK(5, 0)
#define MANUFACTURER_ID 0x300
-#define MANUFACTURER_ID__VALUE 0x00ff
+#define MANUFACTURER_ID__VALUE GENMASK(7, 0)
#define DEVICE_ID 0x310
-#define DEVICE_ID__VALUE 0x00ff
+#define DEVICE_ID__VALUE GENMASK(7, 0)
#define DEVICE_PARAM_0 0x320
-#define DEVICE_PARAM_0__VALUE 0x00ff
+#define DEVICE_PARAM_0__VALUE GENMASK(7, 0)
#define DEVICE_PARAM_1 0x330
-#define DEVICE_PARAM_1__VALUE 0x00ff
+#define DEVICE_PARAM_1__VALUE GENMASK(7, 0)
#define DEVICE_PARAM_2 0x340
-#define DEVICE_PARAM_2__VALUE 0x00ff
+#define DEVICE_PARAM_2__VALUE GENMASK(7, 0)
#define LOGICAL_PAGE_DATA_SIZE 0x350
-#define LOGICAL_PAGE_DATA_SIZE__VALUE 0xffff
+#define LOGICAL_PAGE_DATA_SIZE__VALUE GENMASK(15, 0)
#define LOGICAL_PAGE_SPARE_SIZE 0x360
-#define LOGICAL_PAGE_SPARE_SIZE__VALUE 0xffff
+#define LOGICAL_PAGE_SPARE_SIZE__VALUE GENMASK(15, 0)
#define REVISION 0x370
-#define REVISION__VALUE 0xffff
+#define REVISION__VALUE GENMASK(15, 0)
#define ONFI_DEVICE_FEATURES 0x380
-#define ONFI_DEVICE_FEATURES__VALUE 0x003f
+#define ONFI_DEVICE_FEATURES__VALUE GENMASK(5, 0)
#define ONFI_OPTIONAL_COMMANDS 0x390
-#define ONFI_OPTIONAL_COMMANDS__VALUE 0x003f
+#define ONFI_OPTIONAL_COMMANDS__VALUE GENMASK(5, 0)
#define ONFI_TIMING_MODE 0x3a0
-#define ONFI_TIMING_MODE__VALUE 0x003f
+#define ONFI_TIMING_MODE__VALUE GENMASK(5, 0)
#define ONFI_PGM_CACHE_TIMING_MODE 0x3b0
-#define ONFI_PGM_CACHE_TIMING_MODE__VALUE 0x003f
+#define ONFI_PGM_CACHE_TIMING_MODE__VALUE GENMASK(5, 0)
#define ONFI_DEVICE_NO_OF_LUNS 0x3c0
-#define ONFI_DEVICE_NO_OF_LUNS__NO_OF_LUNS 0x00ff
-#define ONFI_DEVICE_NO_OF_LUNS__ONFI_DEVICE 0x0100
+#define ONFI_DEVICE_NO_OF_LUNS__NO_OF_LUNS GENMASK(7, 0)
+#define ONFI_DEVICE_NO_OF_LUNS__ONFI_DEVICE BIT(8)
#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_L 0x3d0
-#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_L__VALUE 0xffff
+#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_L__VALUE GENMASK(15, 0)
#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_U 0x3e0
-#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_U__VALUE 0xffff
-
-#define FEATURES 0x3f0
-#define FEATURES__N_BANKS 0x0003
-#define FEATURES__ECC_MAX_ERR 0x003c
-#define FEATURES__DMA 0x0040
-#define FEATURES__CMD_DMA 0x0080
-#define FEATURES__PARTITION 0x0100
-#define FEATURES__XDMA_SIDEBAND 0x0200
-#define FEATURES__GPREG 0x0400
-#define FEATURES__INDEX_ADDR 0x0800
+#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_U__VALUE GENMASK(15, 0)
+
+#define FEATURES 0x3f0
+#define FEATURES__N_BANKS GENMASK(1, 0)
+#define FEATURES__ECC_MAX_ERR GENMASK(5, 2)
+#define FEATURES__DMA BIT(6)
+#define FEATURES__CMD_DMA BIT(7)
+#define FEATURES__PARTITION BIT(8)
+#define FEATURES__XDMA_SIDEBAND BIT(9)
+#define FEATURES__GPREG BIT(10)
+#define FEATURES__INDEX_ADDR BIT(11)
#define TRANSFER_MODE 0x400
-#define TRANSFER_MODE__VALUE 0x0003
+#define TRANSFER_MODE__VALUE GENMASK(1, 0)
-#define INTR_STATUS(__bank) (0x410 + ((__bank) * 0x50))
-#define INTR_EN(__bank) (0x420 + ((__bank) * 0x50))
+#define INTR_STATUS(bank) (0x410 + (bank) * 0x50)
+#define INTR_EN(bank) (0x420 + (bank) * 0x50)
/* bit[1:0] is used differently depending on IP version */
-#define INTR__ECC_UNCOR_ERR 0x0001 /* new IP */
-#define INTR__ECC_TRANSACTION_DONE 0x0001 /* old IP */
-#define INTR__ECC_ERR 0x0002 /* old IP */
-#define INTR__DMA_CMD_COMP 0x0004
-#define INTR__TIME_OUT 0x0008
-#define INTR__PROGRAM_FAIL 0x0010
-#define INTR__ERASE_FAIL 0x0020
-#define INTR__LOAD_COMP 0x0040
-#define INTR__PROGRAM_COMP 0x0080
-#define INTR__ERASE_COMP 0x0100
-#define INTR__PIPE_CPYBCK_CMD_COMP 0x0200
-#define INTR__LOCKED_BLK 0x0400
-#define INTR__UNSUP_CMD 0x0800
-#define INTR__INT_ACT 0x1000
-#define INTR__RST_COMP 0x2000
-#define INTR__PIPE_CMD_ERR 0x4000
-#define INTR__PAGE_XFER_INC 0x8000
-
-#define PAGE_CNT(__bank) (0x430 + ((__bank) * 0x50))
-#define ERR_PAGE_ADDR(__bank) (0x440 + ((__bank) * 0x50))
-#define ERR_BLOCK_ADDR(__bank) (0x450 + ((__bank) * 0x50))
+#define INTR__ECC_UNCOR_ERR BIT(0) /* new IP */
+#define INTR__ECC_TRANSACTION_DONE BIT(0) /* old IP */
+#define INTR__ECC_ERR BIT(1) /* old IP */
+#define INTR__DMA_CMD_COMP BIT(2)
+#define INTR__TIME_OUT BIT(3)
+#define INTR__PROGRAM_FAIL BIT(4)
+#define INTR__ERASE_FAIL BIT(5)
+#define INTR__LOAD_COMP BIT(6)
+#define INTR__PROGRAM_COMP BIT(7)
+#define INTR__ERASE_COMP BIT(8)
+#define INTR__PIPE_CPYBCK_CMD_COMP BIT(9)
+#define INTR__LOCKED_BLK BIT(10)
+#define INTR__UNSUP_CMD BIT(11)
+#define INTR__INT_ACT BIT(12)
+#define INTR__RST_COMP BIT(13)
+#define INTR__PIPE_CMD_ERR BIT(14)
+#define INTR__PAGE_XFER_INC BIT(15)
+#define INTR__ERASED_PAGE BIT(16)
+
+#define PAGE_CNT(bank) (0x430 + (bank) * 0x50)
+#define ERR_PAGE_ADDR(bank) (0x440 + (bank) * 0x50)
+#define ERR_BLOCK_ADDR(bank) (0x450 + (bank) * 0x50)
#define ECC_THRESHOLD 0x600
-#define ECC_THRESHOLD__VALUE 0x03ff
+#define ECC_THRESHOLD__VALUE GENMASK(9, 0)
#define ECC_ERROR_BLOCK_ADDRESS 0x610
-#define ECC_ERROR_BLOCK_ADDRESS__VALUE 0xffff
+#define ECC_ERROR_BLOCK_ADDRESS__VALUE GENMASK(15, 0)
#define ECC_ERROR_PAGE_ADDRESS 0x620
-#define ECC_ERROR_PAGE_ADDRESS__VALUE 0x0fff
-#define ECC_ERROR_PAGE_ADDRESS__BANK 0xf000
+#define ECC_ERROR_PAGE_ADDRESS__VALUE GENMASK(11, 0)
+#define ECC_ERROR_PAGE_ADDRESS__BANK GENMASK(15, 12)
#define ECC_ERROR_ADDRESS 0x630
-#define ECC_ERROR_ADDRESS__OFFSET 0x0fff
-#define ECC_ERROR_ADDRESS__SECTOR_NR 0xf000
+#define ECC_ERROR_ADDRESS__OFFSET GENMASK(11, 0)
+#define ECC_ERROR_ADDRESS__SECTOR_NR GENMASK(15, 12)
#define ERR_CORRECTION_INFO 0x640
-#define ERR_CORRECTION_INFO__BYTEMASK 0x00ff
-#define ERR_CORRECTION_INFO__DEVICE_NR 0x0f00
-#define ERR_CORRECTION_INFO__ERROR_TYPE 0x4000
-#define ERR_CORRECTION_INFO__LAST_ERR_INFO 0x8000
+#define ERR_CORRECTION_INFO__BYTEMASK GENMASK(7, 0)
+#define ERR_CORRECTION_INFO__DEVICE_NR GENMASK(11, 8)
+#define ERR_CORRECTION_INFO__ERROR_TYPE BIT(14)
+#define ERR_CORRECTION_INFO__LAST_ERR_INFO BIT(15)
#define ECC_COR_INFO(bank) (0x650 + (bank) / 2 * 0x10)
#define ECC_COR_INFO__SHIFT(bank) ((bank) % 2 * 8)
-#define ECC_COR_INFO__MAX_ERRORS 0x007f
-#define ECC_COR_INFO__UNCOR_ERR 0x0080
+#define ECC_COR_INFO__MAX_ERRORS GENMASK(6, 0)
+#define ECC_COR_INFO__UNCOR_ERR BIT(7)
+
+#define CFG_DATA_BLOCK_SIZE 0x6b0
+
+#define CFG_LAST_DATA_BLOCK_SIZE 0x6c0
+
+#define CFG_NUM_DATA_BLOCKS 0x6d0
+
+#define CFG_META_DATA_SIZE 0x6e0
#define DMA_ENABLE 0x700
-#define DMA_ENABLE__FLAG 0x0001
+#define DMA_ENABLE__FLAG BIT(0)
#define IGNORE_ECC_DONE 0x710
-#define IGNORE_ECC_DONE__FLAG 0x0001
+#define IGNORE_ECC_DONE__FLAG BIT(0)
#define DMA_INTR 0x720
#define DMA_INTR_EN 0x730
-#define DMA_INTR__TARGET_ERROR 0x0001
-#define DMA_INTR__DESC_COMP_CHANNEL0 0x0002
-#define DMA_INTR__DESC_COMP_CHANNEL1 0x0004
-#define DMA_INTR__DESC_COMP_CHANNEL2 0x0008
-#define DMA_INTR__DESC_COMP_CHANNEL3 0x0010
-#define DMA_INTR__MEMCOPY_DESC_COMP 0x0020
+#define DMA_INTR__TARGET_ERROR BIT(0)
+#define DMA_INTR__DESC_COMP_CHANNEL0 BIT(1)
+#define DMA_INTR__DESC_COMP_CHANNEL1 BIT(2)
+#define DMA_INTR__DESC_COMP_CHANNEL2 BIT(3)
+#define DMA_INTR__DESC_COMP_CHANNEL3 BIT(4)
+#define DMA_INTR__MEMCOPY_DESC_COMP BIT(5)
#define TARGET_ERR_ADDR_LO 0x740
-#define TARGET_ERR_ADDR_LO__VALUE 0xffff
+#define TARGET_ERR_ADDR_LO__VALUE GENMASK(15, 0)
#define TARGET_ERR_ADDR_HI 0x750
-#define TARGET_ERR_ADDR_HI__VALUE 0xffff
+#define TARGET_ERR_ADDR_HI__VALUE GENMASK(15, 0)
#define CHNL_ACTIVE 0x760
-#define CHNL_ACTIVE__CHANNEL0 0x0001
-#define CHNL_ACTIVE__CHANNEL1 0x0002
-#define CHNL_ACTIVE__CHANNEL2 0x0004
-#define CHNL_ACTIVE__CHANNEL3 0x0008
+#define CHNL_ACTIVE__CHANNEL0 BIT(0)
+#define CHNL_ACTIVE__CHANNEL1 BIT(1)
+#define CHNL_ACTIVE__CHANNEL2 BIT(2)
+#define CHNL_ACTIVE__CHANNEL3 BIT(3)
#define FAIL 1 /*failed flag*/
#define PASS 0 /*success flag*/
-#define CLK_X 5
-#define CLK_MULTI 4
-
-#define ONFI_BLOOM_TIME 1
-#define MODE5_WORKAROUND 0
-
-
#define MODE_00 0x00000000
#define MODE_01 0x04000000
#define MODE_10 0x08000000
#define MODE_11 0x0C000000
-#define ECC_SECTOR_SIZE 512
-
-struct nand_buf {
- int head;
- int tail;
- uint8_t *buf;
- dma_addr_t dma_buf;
-};
-
-#define INTEL_CE4100 1
-#define INTEL_MRST 2
-#define DT 3
-
struct denali_nand_info {
struct nand_chip nand;
+ unsigned long clk_x_rate; /* bus interface clock rate */
int flash_bank; /* currently selected chip */
- int status;
- int platform;
- struct nand_buf buf;
struct device *dev;
- int total_used_banks;
- int page;
void __iomem *flash_reg; /* Register Interface */
void __iomem *flash_mem; /* Host Data/Command Interface */
/* elements used by ISR */
struct completion complete;
spinlock_t irq_lock;
+ uint32_t irq_mask;
uint32_t irq_status;
int irq;
+ void *buf;
+ dma_addr_t dma_addr;
+ int dma_avail;
int devnum; /* represent how many nands connected */
int bbtskipbytes;
int max_banks;
unsigned int revision;
+ unsigned long ecc_strength_avail;
unsigned int caps;
+ const struct nand_ecc_setting *avail_ecc_settings;
};
#define DENALI_CAP_HW_ECC_FIXUP BIT(0)
@@ -29,13 +29,30 @@ struct denali_dt {
struct clk *clk;
};
+#define DENALI_MAX_ECC_SETTINGS 4
+
struct denali_dt_data {
unsigned int revision;
unsigned int caps;
+ struct nand_ecc_setting avail_ecc_settings[DENALI_MAX_ECC_SETTINGS];
};
static const struct denali_dt_data denali_socfpga_data = {
.caps = DENALI_CAP_HW_ECC_FIXUP,
+ .avail_ecc_settings = {{512, 8}, {512, 15}},
+};
+
+static const struct denali_dt_data denali_uniphier_v5a_data = {
+ .caps = DENALI_CAP_HW_ECC_FIXUP |
+ DENALI_CAP_DMA_64BIT,
+ .avail_ecc_settings = {{1024, 8}, {1024, 16}, {1024, 24}},
+};
+
+static const struct denali_dt_data denali_uniphier_v5b_data = {
+ .revision = 0x0501,
+ .caps = DENALI_CAP_HW_ECC_FIXUP |
+ DENALI_CAP_DMA_64BIT,
+ .avail_ecc_settings = {{1024, 8}, {1024, 16}},
};
static const struct of_device_id denali_nand_dt_ids[] = {
@@ -43,6 +60,14 @@ static const struct of_device_id denali_nand_dt_ids[] = {
.compatible = "altr,socfpga-denali-nand",
.data = &denali_socfpga_data,
},
+ {
+ .compatible = "socionext,uniphier-denali-nand-v5a",
+ .data = &denali_uniphier_v5a_data,
+ },
+ {
+ .compatible = "socionext,uniphier-denali-nand-v5b",
+ .data = &denali_uniphier_v5b_data,
+ },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, denali_nand_dt_ids);
@@ -64,9 +89,9 @@ static int denali_dt_probe(struct platform_device *pdev)
if (data) {
denali->revision = data->revision;
denali->caps = data->caps;
+ denali->avail_ecc_settings = data->avail_ecc_settings;
}
- denali->platform = DT;
denali->dev = &pdev->dev;
denali->irq = platform_get_irq(pdev, 0);
if (denali->irq < 0) {
@@ -93,6 +118,8 @@ static int denali_dt_probe(struct platform_device *pdev)
}
clk_prepare_enable(dt->clk);
+ denali->clk_x_rate = clk_get_rate(dt->clk);
+
ret = denali_init(denali);
if (ret)
goto out_disable_clk;
@@ -19,6 +19,9 @@
#define DENALI_NAND_NAME "denali-nand-pci"
+#define INTEL_CE4100 1
+#define INTEL_MRST 2
+
/* List of platforms this NAND controller has be integrated into */
static const struct pci_device_id denali_pci_ids[] = {
{ PCI_VDEVICE(INTEL, 0x0701), INTEL_CE4100 },
@@ -27,6 +30,10 @@ static const struct pci_device_id denali_pci_ids[] = {
};
MODULE_DEVICE_TABLE(pci, denali_pci_ids);
+static const struct nand_ecc_setting denali_pci_avail_ecc_settings[] = {
+ {512, 8}, {512, 15}, {/* sentinel */}
+};
+
static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
{
int ret;
@@ -45,13 +52,11 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
}
if (id->driver_data == INTEL_CE4100) {
- denali->platform = INTEL_CE4100;
mem_base = pci_resource_start(dev, 0);
mem_len = pci_resource_len(dev, 1);
csr_base = pci_resource_start(dev, 1);
csr_len = pci_resource_len(dev, 1);
} else {
- denali->platform = INTEL_MRST;
csr_base = pci_resource_start(dev, 0);
csr_len = pci_resource_len(dev, 0);
mem_base = pci_resource_start(dev, 1);
@@ -65,6 +70,8 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
pci_set_master(dev);
denali->dev = &dev->dev;
denali->irq = dev->irq;
+ denali->clk_x_rate = 200000000; /* 200 MHz */
+ denali->avail_ecc_settings = denali_pci_avail_ecc_settings;
ret = pci_request_regions(dev, DENALI_NAND_NAME);
if (ret) {
This patch shows how the previous commit is used in a driver. Please do not apply this. (This is applicable on linux next-20170418) Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> --- .../devicetree/bindings/mtd/denali-nand.txt | 17 + drivers/mtd/nand/denali.c | 1693 +++++++++----------- drivers/mtd/nand/denali.h | 297 ++-- drivers/mtd/nand/denali_dt.c | 29 +- drivers/mtd/nand/denali_pci.c | 11 +- 5 files changed, 969 insertions(+), 1078 deletions(-)