@@ -155,6 +155,13 @@ config TARGET_MX6CUBOXI
select BOARD_LATE_INIT
select SUPPORT_SPL
+config TARGET_MX6LOGICPD
+ bool "mx6logicpd"
+ select BOARD_EARLY_INIT_F
+ select BOARD_LATE_INIT
+ select DM
+ select DM_THERMAL
+
config TARGET_MX6QARM2
bool "mx6qarm2"
@@ -404,6 +411,7 @@ source "board/gateworks/gw_ventana/Kconfig"
source "board/kosagi/novena/Kconfig"
source "board/samtec/vining_2000/Kconfig"
source "board/liebherr/mccmon6/Kconfig"
+source "board/logicpd/imx6/Kconfig"
source "board/seco/Kconfig"
source "board/solidrun/mx6cuboxi/Kconfig"
source "board/technexion/pico-imx6ul/Kconfig"
new file mode 100644
@@ -0,0 +1,12 @@
+if TARGET_MX6LOGICPD
+
+config SYS_BOARD
+ default "imx6"
+
+config SYS_VENDOR
+ default "logicpd"
+
+config SYS_CONFIG_NAME
+ default "imx6_logic"
+
+endif
new file mode 100644
@@ -0,0 +1,6 @@
+MX6LOGICPD BOARD
+M: Adam Ford <aford173@gmail.com>
+S: Maintained
+F: board/logicpd/imx6/
+F: include/configs/imx6_logic.h
+F: configs/imx6q_logic_defconfig
new file mode 100644
@@ -0,0 +1,11 @@
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := imx6logic.o
+obj-$(CONFIG_POWER_PFUZE100) += ../../freescale/common/pfuze.o
+
new file mode 100644
@@ -0,0 +1,37 @@
+U-Boot for LogicPD i.MX6 Development Kit
+----------------------------------------
+
+This file contains information for the port of U-Boot to the Logic PD Development kit.
+
+Logic PD has an i.MX6 System On Module (SOM) and a correspondong development
+board. SOM has a built-in microSD socket, DDR and NAND flash. The development kit has
+an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
+
+On the intial release, the SOM came with an i.MX6D and i.MX6Q.
+
+For more details about Logic PD i.MX6 Development kit, visit:
+https://www.logicpd.com/
+
+Building U-Boot for Logic PD Development Kit
+--------------------------------------------
+To build U-Boot for the Dual and Quad variants:
+
+ make imx6q_logic_defconfig
+ make u-boot.imx ARCH=arm CROSS_COMPILE=arm-linux-
+
+
+Flashing U-Boot into the SD card
+--------------------------------
+
+See README.imximage for details on booting from SD
+
+Flashing U-Boot into NAND
+-------------------------
+Once in Linux with MTD support for the NAND on /dev/mtd0, program U-Boot with the following:
+with:
+
+ kobs-ng init -v -x u-boot.imx
+
+Additional Support Documentation can be found at:
+https://support.logicpd.com/
+
new file mode 100644
@@ -0,0 +1,343 @@
+/*
+ * Copyright (C) 2017 Logic PD, Inc.
+ *
+ * Author: Adam Ford <aford173@gmail.com>
+ *
+ * Based on SabreSD by Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <linux/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include "../../freescale/common/pfuze.h"
+#include <asm/arch/mx6-ddr.h>
+#include <usb.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define NAND_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL ( \
+ PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_60ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_SLOW)
+
+#define EPDC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define I2C_PMIC 2
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+ return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart2_pads[] = {
+ MX6_PAD_SD4_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD4_DAT5__UART2_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD4_DAT6__UART2_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD4_DAT7__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart3_pads[] = {
+ MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_EB3__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_RX_ER__ENET_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ /* LAN8710A PHY Reset */
+ MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
+ /* LAN8710A nINT Signal */
+ MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+ struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+ /* Set GPIO_16 as ENET_REF_CLK_OUT */
+ setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
+
+ /* Ensure nINT is input */
+ gpio_direction_input(IMX_GPIO_NR(4, 7));
+
+ /* Reset LAN8710A PHY */
+ gpio_direction_output(IMX_GPIO_NR(4, 9) , 0);
+ udelay(150);
+ gpio_set_value(IMX_GPIO_NR(4, 9), 1);
+ mdelay(50);
+}
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+ MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+
+static struct i2c_pads_info i2c_pad_info3 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ .gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ .gp = IMX_GPIO_NR(3, 17)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ .gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ .gp = IMX_GPIO_NR(3, 18)
+ }
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+ imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+ imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
+}
+
+static iomux_v3_cfg_t const pmic_pads[] = {
+ MX6_PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_pmic_pins(void)
+{
+ imx_iomux_v3_setup_multiple_pads(pmic_pads, ARRAY_SIZE(pmic_pads));
+}
+
+static iomux_v3_cfg_t const nand_pads[] = {
+ MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+};
+
+static void setup_nand_pins(void)
+{
+ imx_iomux_v3_setup_multiple_pads(nand_pads, ARRAY_SIZE(nand_pads));
+}
+
+
+struct fsl_esdhc_cfg usdhc_cfg[] = {
+ {USDHC1_BASE_ADDR},
+ {USDHC2_BASE_ADDR},
+};
+
+#define USDHC1_CD_GPIO IMX_GPIO_NR(6, 16)
+#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
+
+int board_mmc_get_env_dev(int devno)
+{
+ return devno - 1;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = !gpio_get_value(USDHC1_CD_GPIO);
+ break;
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int ret;
+ int i;
+
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-Boot device node) (Physical Port)
+ * mmc0 SOM
+ * mmc1 Baseboard
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+ gpio_direction_input(USDHC1_CD_GPIO);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+ gpio_direction_input(USDHC2_CD_GPIO);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers");
+ printf("(%d) then supported by the board (%d)\n",
+ i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+ return -EINVAL;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret)
+ return ret;
+ }
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+ return 1;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ setup_iomux_enet();
+ return cpu_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+ setup_pmic_pins();
+ setup_nand_pins();
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+ enable_fec_anatop_clock(0, ENET_50MHZ);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, &i2c_pad_info3);
+ return 0;
+}
+
+int power_init_board(void)
+{
+ struct pmic *p;
+
+ p = pfuze_common_init(I2C_PMIC);
+ if (!p)
+ return -ENODEV;
+
+ return pfuze_mode_init(p, APS_PFM);
+}
+
+static const struct boot_mode board_boot_modes[] = {
+ /* 4 bit bus width */
+ /* 4 bit bus width */
+ {"sd1", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+ {"sd2", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+ {NULL, 0},
+};
+
+
+int board_late_init(void)
+{
+ add_board_boot_modes(board_boot_modes);
+ setenv("board_name", "imx6logic");
+
+ if (is_mx6dq()) {
+ setenv("board_rev", "MX6DQ");
+ setenv("fdt_file", "imx6q-logicpd.dtb");
+ }
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: Logic PD i.MX6 SOM\n");
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) 2017 Logic PD, Inc.
+ * Adam Ford <aford173@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#include <asm/imx-common/imximage.cfg>
+
+/* image version */
+IMAGE_VERSION 2
+
+BOOT_OFFSET FLASH_OFFSET_STANDARD
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+#include "asm/arch-mx6/mx6-ddr.h"
+#include "asm/arch-mx6/iomux.h"
+#include "asm/arch-mx6/crm_regs.h"
+
+DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000C0000
+DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000
+DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00000030
+DATA 4, MX6_IOM_DRAM_CAS, 0x00000030
+DATA 4, MX6_IOM_DRAM_RAS, 0x00000030
+DATA 4, MX6_IOM_GRP_ADDDS, 0x00000030
+DATA 4, MX6_IOM_DRAM_RESET, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDBA2, 0x00000000
+DATA 4, MX6_IOM_DRAM_SDODT0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDODT1, 0x00000030
+DATA 4, MX6_IOM_GRP_CTLDS, 0x00000030
+DATA 4, MX6_IOM_DDRMODE_CTL, 0x00020000
+DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000030
+DATA 4, MX6_IOM_GRP_DDRMODE, 0x00020000
+DATA 4, MX6_IOM_GRP_B0DS, 0x00000030
+DATA 4, MX6_IOM_GRP_B1DS, 0x00000030
+DATA 4, MX6_IOM_GRP_B2DS, 0x00000030
+DATA 4, MX6_IOM_GRP_B3DS, 0x00000030
+DATA 4, MX6_IOM_DRAM_DQM0, 0x00000030
+DATA 4, MX6_IOM_DRAM_DQM1, 0x00000030
+DATA 4, MX6_IOM_DRAM_DQM2, 0x00000030
+DATA 4, MX6_IOM_DRAM_DQM3, 0x00000030
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
+DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xA1390003
+DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x002D003A
+DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x0038002B
+DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x03340338
+DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x0334032C
+DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x4036383C
+DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x2E384038
+DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800
+DATA 4, MX6_MMDC_P0_MDPDC, 0x00020036
+DATA 4, MX6_MMDC_P0_MDOTC, 0x09444040
+DATA 4, MX6_MMDC_P0_MDCFG0, 0xB8BE7955
+DATA 4, MX6_MMDC_P0_MDCFG1, 0xFF328F64
+DATA 4, MX6_MMDC_P0_MDCFG2, 0x01FF00DB
+DATA 4, MX6_MMDC_P0_MDMISC, 0x00011740
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
+DATA 4, MX6_MMDC_P0_MDRWD, 0x000026D2
+DATA 4, MX6_MMDC_P0_MDOR, 0x00BE1023
+DATA 4, MX6_MMDC_P0_MDASP, 0x00000047
+DATA 4, MX6_MMDC_P0_MDCTL, 0x85190000
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00888032
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008031
+DATA 4, MX6_MMDC_P0_MDSCR, 0x19408030
+DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040
+DATA 4, MX6_MMDC_P0_MDREF, 0x00007800
+DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00000007
+DATA 4, MX6_MMDC_P0_MDPDC, 0x00025576
+DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000
+
+/* set the default clock gate to save power */
+DATA 4, CCM_CCGR0, 0x00C03F3F
+DATA 4, CCM_CCGR1, 0x0030FC03
+DATA 4, CCM_CCGR2, 0x0FFFC000
+DATA 4, CCM_CCGR3, 0x3FF00000
+DATA 4, CCM_CCGR4, 0xFFFFF300
+DATA 4, CCM_CCGR5, 0x0F0000F3
+DATA 4, CCM_CCGR6, 0x00000FFF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4 MX6_IOMUXC_GPR4 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4 MX6_IOMUXC_GPR6 0x007F007F
+DATA 4 MX6_IOMUXC_GPR7 0x007F007F
new file mode 100644
@@ -0,0 +1,30 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_MX6LOGICPD=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/logicpd/imx6/mx6q_2x_MT41K512M16HA.cfg,MX6Q"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="i.MX6 Logic # "
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_NAND_MXS=y
+CONFIG_DISPLAY_CPUINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_OF_LIBFDT=y
new file mode 100644
@@ -0,0 +1,198 @@
+/*
+ * Copyright (C) 2017 Logic PD, Inc.
+ *
+ * Configuration settings for the LogicPD i.MX6 SOM.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __IMX6LOGIC_CONFIG_H
+#define __IMX6LOGIC_CONFIG_H
+
+#define CONFIG_MXC_UART_BASE UART1_BASE
+#define CONSOLE_DEV "ttymxc0"
+
+#include <config_distro_defaults.h>
+#include "mx6_common.h"
+
+#define CONFIG_IMX_THERMAL
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
+
+#define CONFIG_MXC_UART
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* Dev kit SD card */
+
+/* Ethernet Configs */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 0
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+
+/* Command definition */
+#define CONFIG_CMD_BMODE
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=zImage\0" \
+ "bootm_size=0x10000000\0" \
+ "fdt_addr_r=0x18000000\0" \
+ "fdt_addr=0x18000000\0" \
+ "ramdisk_addr_r=0x13000000\0" \
+ "ramdiskaddr=0x13000000\0" \
+ "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
+ "ramdisk_file=rootfs.cpio.uboot\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "console=" CONSOLE_DEV "\0" \
+ "mmcdev=1\0" \
+ "mmcpart=1\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "nandroot=ubi0:rootfs rootfstype=ubifs\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate}" \
+ " root=${mmcroot} ${mtdparts}\0" \
+ "nandargs=setenv bootargs console=${console},${baudrate}" \
+ " ubi.mtd=fs root=${nandroot} ${mtdparts}\0" \
+ "ramargs=setenv bootargs console=${console},${baudrate}" \
+ " root=/dev/ram rw ${mtdparts}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...;" \
+ " source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image};" \
+ " setenv kernelsize ${filesize}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "loadramdisk=fatload mmc ${mmcdev}:${mmcpart} ${ramdiskaddr} ${ramdisk_file};" \
+ " setenv ramdisksize ${filesize}\0" \
+ "mmcboot=echo Booting from mmc...; run mmcargs; run loadimage;" \
+ " run loadfdt; bootz ${loadaddr} - ${fdt_addr}\0" \
+ "mmcramboot=run ramargs; run loadimage;" \
+ " run loadfdt; run loadramdisk;" \
+ " bootz ${loadaddr} ${ramdiskaddr} ${fdt_addr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ " run nandargs;" \
+ " nand read ${loadaddr} kernel ${kernelsize};" \
+ " nand read ${fdt_addr} dtb;" \
+ " bootz ${loadaddr} - ${fdt_addr}\0" \
+ "nandramboot=echo Booting RAMdisk from nand ...; " \
+ " nand read ${ramdiskaddr} fs ${ramdisksize};" \
+ " nand read ${loadaddr} kernel ${kernelsize};" \
+ " nand read ${fdt_addr} dtb;" \
+ " run ramargs;" \
+ " bootz ${loadaddr} ${ramdiskaddr} ${fdt_addr}\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs" \
+ " ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0" \
+ "autoboot=mmc dev ${mmcdev};" \
+ "if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+#define CONFIG_BOOTCOMMAND \
+ "run autoboot"
+
+#define CONFIG_ARP_TIMEOUT 200UL
+
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END 0x10010000
+#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
+
+#define CONFIG_STACKSIZE (128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* Environment organization */
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x400000
+#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
+
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_MXC_I2C2
+#define CONFIG_SYS_I2C_MXC_I2C3
+#define CONFIG_SYS_I2C_SPEED 400000
+#define CONFIG_SYS_I2C_SLAVE 0x8
+
+/* NAND flash command */
+
+#define CONFIG_CMD_NAND_TRIMFFS
+
+/* NAND stuff */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
+
+/* MTD device */
+# define CONFIG_MTD_DEVICE
+# define CONFIG_CMD_MTDPARTS
+# define CONFIG_MTD_PARTITIONS
+# define MTDIDS_DEFAULT "nand0=gpmi-nand"
+# define MTDPARTS_DEFAULT "mtdparts=gpmi-nand:4m(uboot)," \
+ "1m(env),16m(kernel),1m(dtb),-(fs)"
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
+
+#endif /* __IMX6LOGIC_CONFIG_H */
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The SOM has a built-in microSD socket, DDR and NAND flash. The development kit has an SMSC Ethernet PHY, serial debug port and a variety of peripherals. This have been verified to boot the i.MX6Q version over either SD on the development kit or NAND built into the SOM. Signed-off-by: Adam Ford <aford173@gmail.com> --- Changes in V2: - Alphabetize the modified Kconfig file - Clean up README file. - Elminate fdt_high and initrd_high and add bootm_size - Changed MTDPARTS_DEFAULT to increase the kernel size to 16MB - Cleaned up the mx6q_2x_MT41K512M16HA.cfg to include headers, replace hard-coded addresses with human-readable ones, and remove dead code - Updated mx6q_2x_MT41K512M16HA.cfg to use BOOT_OFFSET since SD and NAND have the same offset - Removed 'ifdef' references that were always true. - Removed CPU references that didn't exist. - And made local variables static - Add reference to worked used to derrive this code