@@ -794,6 +794,10 @@ F: package/angularjs/
N: Ilias Apalodimas <apalos@gmail.com>
F: package/keepalived/
+N: Jagan Teki <jagan@amarulasolutions.com>
+F: board/engicam/
+F: configs/engicam_imx6q_icore_defconfig
+
N: James Knight <james.knight@rockwellcollins.com>
F: package/atkmm/
F: package/cairomm/
new file mode 100644
@@ -0,0 +1,46 @@
+# Minimal SD card image for the Freescale boards Template
+#
+# We mimic the .sdcard Freescale's image format:
+# * the SD card must have 1 kB free space at the beginning,
+# * U-Boot is dumped like SPL at 1K and u-boot-dtb.img at 69K offsets.
+# * a FAT partition at offset 8 MB is containing zImage/uImage and DTB files
+# * a single root filesystem partition is required (ext2, ext3 or ext4)
+#
+
+image boot.vfat {
+ vfat {
+ files = {
+ %FILES%
+ }
+ }
+ size = 16M
+}
+
+image sdcard.img {
+ hdimage {
+ }
+
+ partition SPL {
+ in-partition-table = "no"
+ image = "SPL"
+ offset = 1024
+ }
+
+ partition u-boot-dtb {
+ in-partition-table = "no"
+ image = "u-boot-dtb.img"
+ offset = 69K
+ }
+
+ partition boot {
+ partition-type = 0xC
+ bootable = "true"
+ image = "boot.vfat"
+ offset = 8M
+ }
+
+ partition rootfs {
+ partition-type = 0x83
+ image = "rootfs.ext2"
+ }
+}
new file mode 100755
@@ -0,0 +1,54 @@
+#!/usr/bin/env bash
+
+#
+# dtb_list extracts the list of DTB files from BR2_LINUX_KERNEL_INTREE_DTS_NAME
+# in ${BR_CONFIG}, then prints the corresponding list of file names for the
+# genimage configuration file
+#
+dtb_list()
+{
+ local DTB_LIST="$(sed -n 's/^BR2_LINUX_KERNEL_INTREE_DTS_NAME="\([a-z0-9 \-]*\)"$/\1/p' ${BR2_CONFIG})"
+
+ for dt in $DTB_LIST; do
+ echo -n "\"$dt.dtb\", "
+ done
+}
+
+#
+# linux_image extracts the Linux image format from BR2_LINUX_KERNEL_UIMAGE in
+# ${BR_CONFIG}, then prints the corresponding file name for the genimage
+# configuration file
+#
+linux_image()
+{
+ if grep -Eq "^BR2_LINUX_KERNEL_UIMAGE=y$" ${BR2_CONFIG}; then
+ echo "\"uImage\""
+ else
+ echo "\"zImage\""
+ fi
+}
+
+main()
+{
+ local FILES="$(dtb_list) $(linux_image)"
+ local GENIMAGE_CFG="$(mktemp --suffix genimage.cfg)"
+ local GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
+
+ sed -e "s/%FILES%/${FILES}/" \
+ board/engicam/icorem6/genimage.cfg > ${GENIMAGE_CFG}
+
+ rm -rf "${GENIMAGE_TMP}"
+
+ genimage \
+ --rootpath "${TARGET_DIR}" \
+ --tmppath "${GENIMAGE_TMP}" \
+ --inputpath "${BINARIES_DIR}" \
+ --outputpath "${BINARIES_DIR}" \
+ --config "${GENIMAGE_CFG}"
+
+ rm -f ${GENIMAGE_CFG}
+
+ exit $?
+}
+
+main $@
new file mode 100644
@@ -0,0 +1,63 @@
+**************************************
+Engicam i.CoreM6 Quad/Dual Starter Kit
+**************************************
+
+This file documents the Buildroot support for the Engicam i.CoreM6
+Quad/Dual Starter Kit boards.
+
+i.CoreM6 S/DL/D/Q:
+http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+Build
+=====
+
+First, configure Buildroot for the Engicam i.CoreM6 SD boards:
+
+ make engicam_imx6q_icore_defconfig
+
+Build all components:
+
+ make
+
+You will find the following files in output/images/:
+ - imx6q-icore.dtb
+ - rootfs.ext4
+ - rootfs.tar
+ - sdcard.img
+ - SPL
+ - u-boot-dtb.img
+ - uImage
+
+Create a bootable SD card
+=========================
+
+To determine the device associated to the SD card have a look in the
+/proc/partitions file:
+
+ cat /proc/partitions
+
+Buildroot prepares a bootable "sdcard.img" image in the output/images/
+directory, ready to be dumped on a SD card. Launch the following
+command as root:
+
+ dd if=output/images/sdcard.img of=/dev/<your-sd-device>
+
+*** WARNING! This will destroy all the card content. Use with care! ***
+
+For details about the medium image layout, see the definition in
+board/freescale/common/imx/genimage.cfg.template.
+
+Boot the i.CoreM6 boards with SD boot:
+=====================================
+
+To boot your newly created system:
+- insert the SD card in the SD slot of the board;
+- connect 3-wire RS232 serial port J28 on board, and connect with other
+ serial end or USB cable(if serial-to-usb converter used) using
+ a terminal emulator at 115200 bps, 8n1;
+- close JM3 for sd boot.
+- power on the board.
+
+Enjoy!
new file mode 100644
@@ -0,0 +1,40 @@
+BR2_arm=y
+BR2_cortex_a9=y
+BR2_ARM_ENABLE_NEON=y
+BR2_ARM_ENABLE_VFP=y
+BR2_ARM_FPU_VFPV3=y
+
+# System
+BR2_TARGET_GENERIC_GETTY_PORT="ttymxc3"
+
+# required tools to create the SD card image
+BR2_PACKAGE_HOST_DOSFSTOOLS=y
+BR2_PACKAGE_HOST_GENIMAGE=y
+BR2_PACKAGE_HOST_MTOOLS=y
+
+# Filesystem
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/engicam/icorem6/post-image.sh"
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+
+# Bootloader
+BR2_TARGET_UBOOT=y
+BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2017.01"
+BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx6q_icore_mmc"
+BR2_TARGET_UBOOT_NEEDS_DTC=y
+BR2_TARGET_UBOOT_NEEDS_OPENSSL=y
+BR2_TARGET_UBOOT_FORMAT_DTB_IMG=y
+BR2_TARGET_UBOOT_SPL=y
+BR2_TARGET_UBOOT_SPL_NAME="SPL"
+
+# Kernel
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.10"
+BR2_LINUX_KERNEL_DEFCONFIG="imx_v6_v7"
+BR2_LINUX_KERNEL_UIMAGE=y
+BR2_LINUX_KERNEL_UIMAGE_LOADADDR="0x10008000"
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx6q-icore"