diff mbox

[U-Boot,v2] armv8: ls2080aqds: Add support for SD boot

Message ID 1488450949-7987-2-git-send-email-santan.kumar@nxp.com
State Deferred
Headers show

Commit Message

Santan Kumar March 2, 2017, 10:35 a.m. UTC 
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
---
Changes for v2:
 Rebased to latest codebase

Depends on
 York MMU patches: 
	http://patchwork.ozlabs.org/bundle/yorksun/Rewrite_MMU/ 
 For correct type of image creation: 
 	https://patchwork.ozlabs.org/patch/671466/

 arch/arm/cpu/armv8/fsl-layerscape/cpu.c            |  6 +--
 .../cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c    |  6 +--
 board/freescale/ls2080a/ls2080a.c                  |  6 +--
 board/freescale/ls2080aqds/eth.c                   |  8 +---
 board/freescale/ls2080aqds/ls2080aqds.c            |  4 +-
 configs/ls2080aqds_sdcard_defconfig                | 53 ++++++++++++++++++++++
 include/configs/ls2080a_common.h                   |  2 +
 include/configs/ls2080aqds.h                       | 13 +++++-
 8 files changed, 80 insertions(+), 18 deletions(-)
 create mode 100644 configs/ls2080aqds_sdcard_defconfig

Comments

Tom Rini March 2, 2017, 1:46 p.m. UTC | #1 
On Thu, Mar 02, 2017 at 04:05:49PM +0530, Santan Kumar wrote:

A little here please.

> Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
[snip]
> diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
> index ae72939..d63208b 100644
> --- a/include/configs/ls2080a_common.h
> +++ b/include/configs/ls2080a_common.h
> @@ -230,6 +230,8 @@ unsigned long long get_qixis_addr(void);
>  #define CONFIG_SPL_NAND_SUPPORT
>  #define CONFIG_SYS_NAND_U_BOOT_DST	0x80400000
>  #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
> +#elif defined(CONFIG_SD_BOOT)
> +#define CONFIG_SPL_MMC_SUPPORT

This is in Kconfig.

> @@ -165,12 +169,14 @@ unsigned long get_board_ddr_clk(void);
>  #define QIXIS_LBMAP_DFLTBANK		0x00
>  #define QIXIS_LBMAP_ALTBANK		0x04
>  #define QIXIS_LBMAP_NAND		0x09
> +#define QIXIS_LBMAP_SD			0x00
>  #define QIXIS_LBMAP_QSPI		0x0f
>  #define QIXIS_RST_CTL_RESET		0x31
>  #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
>  #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
>  #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
>  #define QIXIS_RCW_SRC_NAND		0x107
> +#define QIXIS_RCW_SRC_SD		0x40
>  #define QIXIS_RCW_SRC_QSPI		0x62
>  #define	QIXIS_RST_FORCE_MEM		0x01

All of this needs to get moved out of the config header file.  Please
make a note to add this to your TODO list, thanks.
diff mbox

Patch

diff --git a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
index 17258a7..d9e2a90 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
@@ -435,7 +435,7 @@  int cpu_eth_init(bd_t *bis)
 {
 	int error = 0;
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 	error = fsl_mc_ldpaa_init(bis);
 #endif
 #ifdef CONFIG_FMAN_ENET
@@ -571,7 +571,7 @@  phys_size_t board_reserve_ram_top(phys_size_t ram_size)
 {
 	phys_size_t ram_top = ram_size;
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 	/* The start address of MC reserved memory needs to be aligned. */
 	ram_top -= mc_get_dram_block_size();
 	ram_top &= ~(CONFIG_SYS_MC_RSV_MEM_ALIGN - 1);
@@ -686,7 +686,7 @@  void dram_init_banksize(void)
 	}
 #endif	/* CONFIG_SYS_MEM_RESERVE_SECURE */
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 	/* Assign memory for MC */
 #ifdef CONFIG_SYS_DDR_BLOCK3_BASE
 	if (gd->bd->bi_dram[2].size >=
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c
index 7faa86c..10d7f47 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c
@@ -18,7 +18,7 @@  static u8 serdes1_prtcl_map[SERDES_PRCTL_COUNT];
 static u8 serdes2_prtcl_map[SERDES_PRCTL_COUNT];
 #endif
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 int xfi_dpmac[XFI8 + 1];
 int sgmii_dpmac[SGMII16 + 1];
 #endif
@@ -103,7 +103,7 @@  void serdes_init(u32 sd, u32 sd_addr, u32 sd_prctl_mask, u32 sd_prctl_shift,
 			debug("Unknown SerDes lane protocol %d\n", lane_prtcl);
 		else {
 			serdes_prtcl_map[lane_prtcl] = 1;
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 			switch (lane_prtcl) {
 			case QSGMII_A:
 				wriop_init_dpmac(sd, 5, (int)lane_prtcl);
@@ -152,7 +152,7 @@  void serdes_init(u32 sd, u32 sd_addr, u32 sd_prctl_mask, u32 sd_prctl_shift,
 
 void fsl_serdes_init(void)
 {
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 	int i , j;
 
 	for (i = XFI1, j = 1; i <= XFI8; i++, j++)
diff --git a/board/freescale/ls2080a/ls2080a.c b/board/freescale/ls2080a/ls2080a.c
index ace5bf6..cff468b 100644
--- a/board/freescale/ls2080a/ls2080a.c
+++ b/board/freescale/ls2080a/ls2080a.c
@@ -64,13 +64,13 @@  int board_eth_init(bd_t *bis)
 	error = smc91111_initialize(0, CONFIG_SMC91111_BASE);
 #endif
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 	error = cpu_eth_init(bis);
 #endif
 	return error;
 }
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 void fdt_fixup_board_enet(void *fdt)
 {
 	int offset;
@@ -128,7 +128,7 @@  int ft_board_setup(void *blob, bd_t *bd)
 
 	fdt_fixup_memory_banks(blob, base, size, 2);
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 	fdt_fixup_board_enet(blob);
 #endif
 
diff --git a/board/freescale/ls2080aqds/eth.c b/board/freescale/ls2080aqds/eth.c
index 59361e9..302ff76 100644
--- a/board/freescale/ls2080aqds/eth.c
+++ b/board/freescale/ls2080aqds/eth.c
@@ -22,7 +22,7 @@ 
 
 #define MC_BOOT_ENV_VAR "mcinitcmd"
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
  /* - In LS2080A there are only 16 SERDES lanes, spread across 2 SERDES banks.
  *   Bank 1 -> Lanes A, B, C, D, E, F, G, H
  *   Bank 2 -> Lanes A,B, C, D, E, F, G, H
@@ -834,8 +834,8 @@  void ls2080a_handle_phy_interface_xsgmii(int i)
 int board_eth_init(bd_t *bis)
 {
 	int error;
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 	char *mc_boot_env_var;
-#ifdef CONFIG_FSL_MC_ENET
 	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
 	int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
 				FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK)
@@ -918,7 +918,3 @@  int board_eth_init(bd_t *bis)
 	error = pci_eth_init(bis);
 	return error;
 }
-
-#ifdef CONFIG_FSL_MC_ENET
-
-#endif
diff --git a/board/freescale/ls2080aqds/ls2080aqds.c b/board/freescale/ls2080aqds/ls2080aqds.c
index 291df4c..2ed8b42 100644
--- a/board/freescale/ls2080aqds/ls2080aqds.c
+++ b/board/freescale/ls2080aqds/ls2080aqds.c
@@ -264,7 +264,7 @@  int arch_misc_init(void)
 }
 #endif
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 void fdt_fixup_board_enet(void *fdt)
 {
 	int offset;
@@ -320,7 +320,7 @@  int ft_board_setup(void *blob, bd_t *bd)
 
 	fsl_fdt_fixup_dr_usb(blob, bd);
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 	fdt_fixup_board_enet(blob);
 #endif
 
diff --git a/configs/ls2080aqds_sdcard_defconfig b/configs/ls2080aqds_sdcard_defconfig
new file mode 100644
index 0000000..874d49e
--- /dev/null
+++ b/configs/ls2080aqds_sdcard_defconfig
@@ -0,0 +1,53 @@ 
+CONFIG_ARM=y
+CONFIG_TARGET_LS2080AQDS=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_ENV_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds"
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4, LS2080A"
+CONFIG_SD_BOOT=y
+CONFIG_BOOTDELAY=10
+CONFIG_SPL=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8b0
+CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_E1000=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_LAYERSCAPE=y
+CONFIG_SYS_NS16550=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_STORAGE=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
index ae72939..d63208b 100644
--- a/include/configs/ls2080a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -230,6 +230,8 @@  unsigned long long get_qixis_addr(void);
 #define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SYS_NAND_U_BOOT_DST	0x80400000
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_SPL_MMC_SUPPORT
 #endif
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x00100000
 #define CONFIG_SYS_SPL_MALLOC_START	0x80200000
diff --git a/include/configs/ls2080aqds.h b/include/configs/ls2080aqds.h
index 93f6b51..3ae97e9 100644
--- a/include/configs/ls2080aqds.h
+++ b/include/configs/ls2080aqds.h
@@ -116,7 +116,9 @@  unsigned long get_board_ddr_clk(void);
 					 CONFIG_SYS_FLASH_BASE + 0x40000000}
 #endif
 
+#ifndef CONFIG_FSL_QSPI
 #define CONFIG_NAND_FSL_IFC
+#endif
 #define CONFIG_SYS_NAND_MAX_ECCPOS	256
 #define CONFIG_SYS_NAND_MAX_OOBFREE	2
 
@@ -151,10 +153,12 @@  unsigned long get_board_ddr_clk(void);
 					FTIM2_NAND_TWHRE(0x1e))
 #define CONFIG_SYS_NAND_FTIM3		0x0
 
+#ifndef CONFIG_FSL_QSPI
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND
+#endif
 
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
 
@@ -165,12 +169,14 @@  unsigned long get_board_ddr_clk(void);
 #define QIXIS_LBMAP_DFLTBANK		0x00
 #define QIXIS_LBMAP_ALTBANK		0x04
 #define QIXIS_LBMAP_NAND		0x09
+#define QIXIS_LBMAP_SD			0x00
 #define QIXIS_LBMAP_QSPI		0x0f
 #define QIXIS_RST_CTL_RESET		0x31
 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
 #define QIXIS_RCW_SRC_NAND		0x107
+#define QIXIS_RCW_SRC_SD		0x40
 #define QIXIS_RCW_SRC_QSPI		0x62
 #define	QIXIS_RST_FORCE_MEM		0x01
 
@@ -234,6 +240,11 @@  unsigned long get_board_ddr_clk(void);
 #define CONFIG_SPL_PAD_TO		0x20000
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 * 1024)
 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(640 * 1024)
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_ENV_OFFSET		0x200000
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_SIZE			0x20000
 #endif
 #else
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
@@ -391,7 +402,7 @@  unsigned long get_board_ddr_clk(void);
 #endif /* CONFIG_SECURE_BOOT */
 
 
-#ifdef CONFIG_FSL_MC_ENET
+#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
 #define CONFIG_FSL_MEMAC
 #define	CONFIG_PHYLIB
 #define CONFIG_PHYLIB_10G