[U-Boot,v1] cmd: sspi: Add an additional argument to set the bus frequency

diff --git a/cmd/spi.c b/cmd/spi.c
index f16ef9a..b495b87 100644
--- a/cmd/spi.c
+++ b/cmd/spi.c
@@ -36,51 +36,52 @@ 
 static unsigned int	bus;
 static unsigned int	cs;
 static unsigned int	mode;
+static unsigned int     hz;
 static int   		bitlen;
 static uchar 		dout[MAX_SPI_BYTES];
 static uchar 		din[MAX_SPI_BYTES];
 
-static int do_spi_xfer(int bus, int cs)
+static int do_spi_xfer(int bus, int cs, unsigned int hz)
 {
 	struct spi_slave *slave;
 	int ret = 0;
 
 #ifdef CONFIG_DM_SPI
 	char name[30], *str;
 	struct udevice *dev;
 
 	snprintf(name, sizeof(name), "generic_%d:%d", bus, cs);
 	str = strdup(name);
 	if (!str)
 		return -ENOMEM;
-	ret = spi_get_bus_and_cs(bus, cs, 1000000, mode, "spi_generic_drv",
+	ret = spi_get_bus_and_cs(bus, cs, hz, mode, "spi_generic_drv",
 				 str, &dev, &slave);
 	if (ret)
 		return ret;
 #else
-	slave = spi_setup_slave(bus, cs, 1000000, mode);
+	slave = spi_setup_slave(bus, cs, hz, mode);
 	if (!slave) {
 		printf("Invalid device %d:%d\n", bus, cs);
 		return -EINVAL;
 	}
 #endif
 
 	ret = spi_claim_bus(slave);
 	if (ret)
 		goto done;
 	ret = spi_xfer(slave, bitlen, dout, din,
 		       SPI_XFER_BEGIN | SPI_XFER_END);
 #ifndef CONFIG_DM_SPI
 	/* We don't get an error code in this case */
 	if (ret)
 		ret = -EIO;
 #endif
 	if (ret) {
 		printf("Error %d during SPI transaction\n", ret);
 	} else {
 		int j;
 
 		for (j = 0; j < ((bitlen + 7) / 8); j++)
 			printf("%02X", din[j]);
 		printf("\n");
 	}
@@ -107,70 +108,73 @@  done:
 int do_spi (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 {
 	char  *cp = 0;
 	uchar tmp;
 	int   j;
 
 	/*
 	 * We use the last specified parameters, unless new ones are
 	 * entered.
 	 */
 
 	if ((flag & CMD_FLAG_REPEAT) == 0)
 	{
 		if (argc >= 2) {
 			mode = CONFIG_DEFAULT_SPI_MODE;
 			bus = simple_strtoul(argv[1], &cp, 10);
 			if (*cp == ':') {
 				cs = simple_strtoul(cp+1, &cp, 10);
 			} else {
 				cs = bus;
 				bus = CONFIG_DEFAULT_SPI_BUS;
 			}
 			if (*cp == '.')
 				mode = simple_strtoul(cp+1, NULL, 10);
 		}
 		if (argc >= 3)
 			bitlen = simple_strtoul(argv[2], NULL, 10);
 		if (argc >= 4) {
 			cp = argv[3];
 			for(j = 0; *cp; j++, cp++) {
 				tmp = *cp - '0';
 				if(tmp > 9)
 					tmp -= ('A' - '0') - 10;
 				if(tmp > 15)
 					tmp -= ('a' - 'A');
 				if(tmp > 15) {
 					printf("Hex conversion error on %c\n", *cp);
 					return 1;
 				}
 				if((j % 2) == 0)
 					dout[j / 2] = (tmp << 4);
 				else
 					dout[j / 2] |= tmp;
 			}
 		}
+		if (argc >= 5)
+			hz = simple_strtoul(argv[4], NULL, 10);
 	}
 
 	if ((bitlen < 0) || (bitlen >  (MAX_SPI_BYTES * 8))) {
 		printf("Invalid bitlen %d\n", bitlen);
 		return 1;
 	}
 
-	if (do_spi_xfer(bus, cs))
+	if (do_spi_xfer(bus, cs, hz))
 		return 1;
 
 	return 0;
 }
 
 /***************************************************/
 
 U_BOOT_CMD(
-	sspi,	5,	1,	do_spi,
+	sspi,	6,	1,	do_spi,
 	"SPI utility command",
-	"[<bus>:]<cs>[.<mode>] <bit_len> <dout> - Send and receive bits\n"
+	"[<bus>:]<cs>[.<mode>] <bit_len> <dout> [<hz>] - Send and receive bits\n"
 	"<bus>     - Identifies the SPI bus\n"
 	"<cs>      - Identifies the chip select\n"
 	"<mode>    - Identifies the SPI mode to use\n"
 	"<bit_len> - Number of bits to send (base 10)\n"
-	"<dout>    - Hexadecimal string that gets sent"
+	"<dout>    - Hexadecimal string that gets sent\n"
+	"[<clk>]   - Bus clock in Hz"
 );