[v3,1/2] mtd: spi-nor: Added spi-nor reset function

Submitted by Kamal Dasu on Feb. 10, 2017, 9:49 p.m.

Details

Message ID 1486763369-31969-2-git-send-email-kdasu.kdev@gmail.com
State Superseded
Delegated to: Cyrille Pitchen
Headers show

Commit Message

Kamal Dasu Feb. 10, 2017, 9:49 p.m.
Refactored spi_nor_scan() code to add spi_nor_init() function that
programs the spi-nor flash to:
1) remove flash protection if applicable
2) set read mode to quad mode if configured such
3) set the address width based on the flash size and vendor

On pm resume spi-nor flash may need to be reconfigured after power
reset, there is no need to go through a full spi_nor_scan(), flash
device driver needs to call spi_nor_reset() to reprogram the flash
to its probed state.

Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>

Conflicts:
	drivers/mtd/spi-nor/spi-nor.c
---
 drivers/mtd/spi-nor/spi-nor.c | 72 +++++++++++++++++++++++++++----------------
 include/linux/mtd/spi-nor.h   | 21 ++++++++++++-
 2 files changed, 65 insertions(+), 28 deletions(-)

Comments

Marek Vasut Feb. 11, 2017, 12:10 p.m.
On 02/10/2017 10:49 PM, Kamal Dasu wrote:
> Refactored spi_nor_scan() code to add spi_nor_init() function that
> programs the spi-nor flash to:
> 1) remove flash protection if applicable
> 2) set read mode to quad mode if configured such
> 3) set the address width based on the flash size and vendor
> 
> On pm resume spi-nor flash may need to be reconfigured after power
> reset, there is no need to go through a full spi_nor_scan(), flash
> device driver needs to call spi_nor_reset() to reprogram the flash
                                      ^^^^^
                                           _init() ? or _setup() ?

> to its probed state.
> 
> Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
> 
> Conflicts:
> 	drivers/mtd/spi-nor/spi-nor.c
> ---
>  drivers/mtd/spi-nor/spi-nor.c | 72 +++++++++++++++++++++++++++----------------
>  include/linux/mtd/spi-nor.h   | 21 ++++++++++++-
>  2 files changed, 65 insertions(+), 28 deletions(-)
> 
> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
> index 70e52ff..2bf7f4f 100644
> --- a/drivers/mtd/spi-nor/spi-nor.c
> +++ b/drivers/mtd/spi-nor/spi-nor.c
> @@ -1526,6 +1526,44 @@ static int s3an_nor_scan(const struct flash_info *info, struct spi_nor *nor)
>  	return 0;
>  }
>  
> +int spi_nor_init(struct spi_nor *nor)
> +{
> +	int ret = 0;
> +	const struct flash_info *info = nor->info;
> +	struct device *dev = nor->dev;
> +
> +	/*
> +	 * Atmel, SST, Intel/Numonyx, and others serial NOR tend to power up
> +	 * with the software protection bits set
> +	 */
> +
> +	if (JEDEC_MFR(info) == SNOR_MFR_ATMEL ||
> +	    JEDEC_MFR(info) == SNOR_MFR_INTEL ||
> +	    JEDEC_MFR(info) == SNOR_MFR_SST ||
> +	    info->flags & SPI_NOR_HAS_LOCK) {
> +		write_enable(nor);
> +		write_sr(nor, 0);
> +		spi_nor_wait_till_ready(nor);
> +	}
> +
> +	if (nor->flash_read == SPI_NOR_QUAD) {
> +		ret = set_quad_mode(nor, info);
> +		if (ret) {
> +			dev_err(dev, "quad mode not supported\n");
> +			return ret;
> +		}
> +	}
> +
> +	if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
> +	    info->flags & SPI_NOR_4B_OPCODES)
> +		spi_nor_set_4byte_opcodes(nor, info);
> +	else
> +		set_4byte(nor, info, 1);
> +
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(spi_nor_init);
> +
>  int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
>  {
>  	const struct flash_info *info = NULL;
> @@ -1571,6 +1609,7 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
>  		}
>  	}
>  
> +	nor->info = info;
>  	mutex_init(&nor->lock);
>  
>  	/*
> @@ -1581,20 +1620,6 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
>  	if (info->flags & SPI_S3AN)
>  		nor->flags |=  SNOR_F_READY_XSR_RDY;
>  
> -	/*
> -	 * Atmel, SST, Intel/Numonyx, and others serial NOR tend to power up
> -	 * with the software protection bits set
> -	 */
> -
> -	if (JEDEC_MFR(info) == SNOR_MFR_ATMEL ||
> -	    JEDEC_MFR(info) == SNOR_MFR_INTEL ||
> -	    JEDEC_MFR(info) == SNOR_MFR_SST ||
> -	    info->flags & SPI_NOR_HAS_LOCK) {
> -		write_enable(nor);
> -		write_sr(nor, 0);
> -		spi_nor_wait_till_ready(nor);
> -	}
> -
>  	if (!mtd->name)
>  		mtd->name = dev_name(dev);
>  	mtd->priv = nor;
> @@ -1669,11 +1694,6 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
>  
>  	/* Quad/Dual-read mode takes precedence over fast/normal */
>  	if (mode == SPI_NOR_QUAD && info->flags & SPI_NOR_QUAD_READ) {
> -		ret = set_quad_mode(nor, info);
> -		if (ret) {
> -			dev_err(dev, "quad mode not supported\n");
> -			return ret;
> -		}
>  		nor->flash_read = SPI_NOR_QUAD;
>  	} else if (mode == SPI_NOR_DUAL && info->flags & SPI_NOR_DUAL_READ) {
>  		nor->flash_read = SPI_NOR_DUAL;
> @@ -1702,17 +1722,11 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
>  
>  	if (info->addr_width)
>  		nor->addr_width = info->addr_width;
> -	else if (mtd->size > 0x1000000) {
> +	else if (mtd->size > 0x1000000)
>  		/* enable 4-byte addressing if the device exceeds 16MiB */
>  		nor->addr_width = 4;
> -		if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
> -		    info->flags & SPI_NOR_4B_OPCODES)
> -			spi_nor_set_4byte_opcodes(nor, info);
> -		else
> -			set_4byte(nor, info, 1);
> -	} else {
> +	else
>  		nor->addr_width = 3;
> -	}
>  
>  	if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
>  		dev_err(dev, "address width is too large: %u\n",
> @@ -1728,6 +1742,10 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
>  			return ret;
>  	}
>  
> +	ret = spi_nor_init(nor);
> +	if (ret)
> +		return ret;
> +
>  	dev_info(dev, "%s (%lld Kbytes)\n", info->name,
>  			(long long)mtd->size >> 10);
>  
> diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
> index f2a7180..945b4d4 100644
> --- a/include/linux/mtd/spi-nor.h
> +++ b/include/linux/mtd/spi-nor.h
> @@ -143,6 +143,8 @@ enum spi_nor_option_flags {
>  	SNOR_F_READY_XSR_RDY	= BIT(4),
>  };
>  
> +struct flash_info;
> +
>  /**
>   * struct spi_nor - Structure for defining a the SPI NOR layer
>   * @mtd:		point to a mtd_info structure
> @@ -176,6 +178,7 @@ enum spi_nor_option_flags {
>   * @priv:		the private data
>   */
>  struct spi_nor {
> +	const struct flash_info *info;

New entry is not documented (see the comment above the struct), also it
shouldn't be at the top IMO , just put it at the bottom or at some more
sensible location.

>  	struct mtd_info		mtd;
>  	struct mutex		lock;
>  	struct device		*dev;
> @@ -220,12 +223,28 @@ static inline struct device_node *spi_nor_get_flash_node(struct spi_nor *nor)
>  }
>  
>  /**
> + * spi_nor_init() - reset scan the SPI NOR

The description really doesn't match what the function does, no ?

> + * @nor:	the spi_nor structure
> + *
> + * The drivers uses this function to initialize the SPI NOR flash device to
> + * its scanned state, it shall use all nor information set on poweron
> + * for the read mode, address width and remove protection for certain spi-nor
> + * manufacturers. This would be needed to be called for flash devices that are
> + * reset during power management.

Doesn't this function just init the SPI NOR to state selected by Linux ?

> + * The chip type name can be provided through the @name parameter.
> + *
> + * Return: 0 for success, others for failure.
> + */
> +int spi_nor_init(struct spi_nor *nor);
> +
> +/**
>   * spi_nor_scan() - scan the SPI NOR
>   * @nor:	the spi_nor structure
>   * @name:	the chip type name
>   * @mode:	the read mode supported by the driver
>   *
> - * The drivers can use this fuction to scan the SPI NOR.
> + * The drivers can use this function to scan the SPI NOR.
>   * In the scanning, it will try to get all the necessary information to
>   * fill the mtd_info{} and the spi_nor{}.
>   *
>

Patch hide | download patch | download mbox

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 70e52ff..2bf7f4f 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -1526,6 +1526,44 @@  static int s3an_nor_scan(const struct flash_info *info, struct spi_nor *nor)
 	return 0;
 }
 
+int spi_nor_init(struct spi_nor *nor)
+{
+	int ret = 0;
+	const struct flash_info *info = nor->info;
+	struct device *dev = nor->dev;
+
+	/*
+	 * Atmel, SST, Intel/Numonyx, and others serial NOR tend to power up
+	 * with the software protection bits set
+	 */
+
+	if (JEDEC_MFR(info) == SNOR_MFR_ATMEL ||
+	    JEDEC_MFR(info) == SNOR_MFR_INTEL ||
+	    JEDEC_MFR(info) == SNOR_MFR_SST ||
+	    info->flags & SPI_NOR_HAS_LOCK) {
+		write_enable(nor);
+		write_sr(nor, 0);
+		spi_nor_wait_till_ready(nor);
+	}
+
+	if (nor->flash_read == SPI_NOR_QUAD) {
+		ret = set_quad_mode(nor, info);
+		if (ret) {
+			dev_err(dev, "quad mode not supported\n");
+			return ret;
+		}
+	}
+
+	if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
+	    info->flags & SPI_NOR_4B_OPCODES)
+		spi_nor_set_4byte_opcodes(nor, info);
+	else
+		set_4byte(nor, info, 1);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(spi_nor_init);
+
 int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 {
 	const struct flash_info *info = NULL;
@@ -1571,6 +1609,7 @@  int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 		}
 	}
 
+	nor->info = info;
 	mutex_init(&nor->lock);
 
 	/*
@@ -1581,20 +1620,6 @@  int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 	if (info->flags & SPI_S3AN)
 		nor->flags |=  SNOR_F_READY_XSR_RDY;
 
-	/*
-	 * Atmel, SST, Intel/Numonyx, and others serial NOR tend to power up
-	 * with the software protection bits set
-	 */
-
-	if (JEDEC_MFR(info) == SNOR_MFR_ATMEL ||
-	    JEDEC_MFR(info) == SNOR_MFR_INTEL ||
-	    JEDEC_MFR(info) == SNOR_MFR_SST ||
-	    info->flags & SPI_NOR_HAS_LOCK) {
-		write_enable(nor);
-		write_sr(nor, 0);
-		spi_nor_wait_till_ready(nor);
-	}
-
 	if (!mtd->name)
 		mtd->name = dev_name(dev);
 	mtd->priv = nor;
@@ -1669,11 +1694,6 @@  int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 
 	/* Quad/Dual-read mode takes precedence over fast/normal */
 	if (mode == SPI_NOR_QUAD && info->flags & SPI_NOR_QUAD_READ) {
-		ret = set_quad_mode(nor, info);
-		if (ret) {
-			dev_err(dev, "quad mode not supported\n");
-			return ret;
-		}
 		nor->flash_read = SPI_NOR_QUAD;
 	} else if (mode == SPI_NOR_DUAL && info->flags & SPI_NOR_DUAL_READ) {
 		nor->flash_read = SPI_NOR_DUAL;
@@ -1702,17 +1722,11 @@  int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 
 	if (info->addr_width)
 		nor->addr_width = info->addr_width;
-	else if (mtd->size > 0x1000000) {
+	else if (mtd->size > 0x1000000)
 		/* enable 4-byte addressing if the device exceeds 16MiB */
 		nor->addr_width = 4;
-		if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
-		    info->flags & SPI_NOR_4B_OPCODES)
-			spi_nor_set_4byte_opcodes(nor, info);
-		else
-			set_4byte(nor, info, 1);
-	} else {
+	else
 		nor->addr_width = 3;
-	}
 
 	if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
 		dev_err(dev, "address width is too large: %u\n",
@@ -1728,6 +1742,10 @@  int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 			return ret;
 	}
 
+	ret = spi_nor_init(nor);
+	if (ret)
+		return ret;
+
 	dev_info(dev, "%s (%lld Kbytes)\n", info->name,
 			(long long)mtd->size >> 10);
 
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index f2a7180..945b4d4 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -143,6 +143,8 @@  enum spi_nor_option_flags {
 	SNOR_F_READY_XSR_RDY	= BIT(4),
 };
 
+struct flash_info;
+
 /**
  * struct spi_nor - Structure for defining a the SPI NOR layer
  * @mtd:		point to a mtd_info structure
@@ -176,6 +178,7 @@  enum spi_nor_option_flags {
  * @priv:		the private data
  */
 struct spi_nor {
+	const struct flash_info *info;
 	struct mtd_info		mtd;
 	struct mutex		lock;
 	struct device		*dev;
@@ -220,12 +223,28 @@  static inline struct device_node *spi_nor_get_flash_node(struct spi_nor *nor)
 }
 
 /**
+ * spi_nor_init() - reset scan the SPI NOR
+ * @nor:	the spi_nor structure
+ *
+ * The drivers uses this function to initialize the SPI NOR flash device to
+ * its scanned state, it shall use all nor information set on poweron
+ * for the read mode, address width and remove protection for certain spi-nor
+ * manufacturers. This would be needed to be called for flash devices that are
+ * reset during power management.
+ *
+ * The chip type name can be provided through the @name parameter.
+ *
+ * Return: 0 for success, others for failure.
+ */
+int spi_nor_init(struct spi_nor *nor);
+
+/**
  * spi_nor_scan() - scan the SPI NOR
  * @nor:	the spi_nor structure
  * @name:	the chip type name
  * @mode:	the read mode supported by the driver
  *
- * The drivers can use this fuction to scan the SPI NOR.
+ * The drivers can use this function to scan the SPI NOR.
  * In the scanning, it will try to get all the necessary information to
  * fill the mtd_info{} and the spi_nor{}.
  *