@@ -1,3 +1,5 @@
+source "drivers/net/phy/Kconfig"
+
config DM_ETH
bool "Enable Driver Model for Ethernet drivers"
depends on DM
@@ -8,32 +10,6 @@ config DM_ETH
This is currently implemented in net/eth.c
Look in include/net.h for details.
-config PHYLIB
- bool "Ethernet PHY (physical media interface) support"
- help
- Enable Ethernet PHY (physical media interface) support.
-
-config RTL8211X_PHY_FORCE_MASTER
- bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
- depends on PHYLIB
- help
- Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
- This can work around link stability and data corruption issues on gigabit
- links which can occur in slave mode on certain PHYs, e.g. on the
- RTL8211C(L).
-
- Please note that two directly connected devices (i.e. via crossover cable)
- will not be able to establish a link between each other if they both force
- master mode. Multiple devices forcing master mode when connected by a
- network switch do not pose a problem as the switch configures its affected
- ports into slave mode.
-
- This option only affects gigabit links. If you must establish a direct
- connection between two devices which both force master mode, try forcing
- the link speed to 100MBit/s.
-
- If unsure, say N.
-
menuconfig NETDEVICES
bool "Network device support"
depends on NET
new file mode 100644
@@ -0,0 +1,90 @@
+
+config BITBANGMII
+ bool "Bit-banged ethernet MII management channel support"
+
+config MV88E6352_SWITCH
+ bool "Marvell 88E6352 switch support"
+
+menuconfig PHYLIB
+ bool "Ethernet PHY (physical media interface) support"
+ help
+ Enable Ethernet PHY (physical media interface) support.
+
+if PHYLIB
+
+config MV88E61XX_SWITCH
+ bool "Marvel MV88E61xx Ethernet switch PHY support."
+
+config PHYLIB_10G
+ bool "Generic 10G PHY support"
+
+config PHY_AQUANTIA
+ bool "Aquantia Ethernet PHYs support"
+
+config PHY_ATHEROS
+ bool "Atheros Ethernet PHYs support"
+
+config PHY_BROADCOM
+ bool "Broadcom Ethernet PHYs support"
+
+config PHY_CORTINA
+ bool "Cortina Ethernet PHYs support"
+
+config PHY_DAVICOM
+ bool "Davicom Ethernet PHYs support"
+
+config PHY_ET1011C
+ bool "LSI TruePHY ET1011C support"
+
+config PHY_LXT
+ bool "LXT971 Ethernet PHY support"
+
+config PHY_MARVELL
+ bool "Marvell Ethernet PHYs support"
+
+config PHY_MICREL
+ bool "Micrel Ethernet PHYs support"
+
+config PHY_NATSEMI
+ bool "National Semiconductor Ethernet PHYs support"
+
+config PHY_REALTEK
+ bool "Realtek Ethernet PHYs support"
+
+config RTL8211X_PHY_FORCE_MASTER
+ bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
+ depends on PHY_REALTEK
+ help
+ Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
+ This can work around link stability and data corruption issues on gigabit
+ links which can occur in slave mode on certain PHYs, e.g. on the
+ RTL8211C(L).
+
+ Please note that two directly connected devices (i.e. via crossover cable)
+ will not be able to establish a link between each other if they both force
+ master mode. Multiple devices forcing master mode when connected by a
+ network switch do not pose a problem as the switch configures its affected
+ ports into slave mode.
+
+ This option only affects gigabit links. If you must establish a direct
+ connection between two devices which both force master mode, try forcing
+ the link speed to 100MBit/s.
+
+ If unsure, say N.
+
+config PHY_SMSC
+ bool "Microchip(SMSC) Ethernet PHYs support"
+
+config PHY_TERANETICS
+ bool "Teranetics Ethernet PHYs support"
+
+config PHY_TI
+ bool "Texas Instruments Ethernet PHYs support"
+
+config PHY_VITESSE
+ bool "Vitesse Ethernet PHYs support"
+
+config PHY_XILINX
+ bool "Xilinx Ethernet PHYs support"
+
+endif #PHYLIB
Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> --- drivers/net/Kconfig | 28 ++------------- drivers/net/phy/Kconfig | 90 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 92 insertions(+), 26 deletions(-) create mode 100644 drivers/net/phy/Kconfig