| Message ID | 20170124182642.29396-1-marek.vasut@gmail.com |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
On Tue, Jan 24, 2017 at 07:26:41PM +0100, Marek Vasut wrote: > Add DT bindings for the Renesas RCar GyroADC block. This block is > a simple 4/8-channel ADC which samples 12/15/24 bits of data every > cycle from all channels. > > Signed-off-by: Marek Vasut <marek.vasut@gmail.com> > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > Cc: Simon Horman <horms+renesas@verge.net.au> > Cc: Jonathan Cameron <jic23@kernel.org> > Cc: linux-renesas-soc@vger.kernel.org > Cc: Wolfram Sang <wsa@the-dreams.de> > Cc: Rob Herring <robh@kernel.org> > Cc: devicetree@vger.kernel.org > --- > V8: - Sync the version with the 2/2 driver patch > - Drop status prop from example > - Add GyroADC block description > - Enumerate the compatible string values > - Make subnodes mandatory > --- > .../bindings/iio/adc/renesas,gyroadc.txt | 99 ++++++++++++++++++++++ > 1 file changed, 99 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt > > diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt > new file mode 100644 > index 000000000000..7f9b3bd120a9 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt > @@ -0,0 +1,99 @@ > +* Renesas RCar GyroADC device driver > + > +The GyroADC block is a reduced SPI block with up to 8 chipselect lines, > +which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs > +are sampled by the GyroADC block in a round-robin fashion and the result > +presented in the GyroADC registers. > + > +Required properties: > +- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc". > + The <soc-specific> should be one of: > + renesas,r8a7791-gyroadc - for the GyroADC block present > + in r8a7791 SoC > + renesas,r8a7792-gyroadc - for the GyroADC with interrupt > + block present in r8a7792 SoC > +- reg: Address and length of the register set for the device > +- clocks: References to all the clocks specified in the clock-names > + property as specified in > + Documentation/devicetree/bindings/clock/clock-bindings.txt. > +- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block > + clock, the "if" is the interface clock. > +- power-domains: Must contain a reference to the PM domain, if available. > +- #address-cells: Should be <1> (setting for the subnodes) for all ADCs > + except for "fujitsu,mb88101a". Should be <0> (setting for > + only subnode) for "fujitsu,mb88101a". > +- #size-cells: Should be <0> (setting for the subnodes) > + > +Sub-nodes: > +You must define subnode(s) which select the connected ADC type and reference > +voltage for the GyroADC channels. > + > +Required properties for subnodes: > +- compatible: Should be either of: > + "fujitsu,mb88101a" > + - Fujitsu MB88101A compatible mode, > + 12bit sampling, up to 4 channels can be sampled in > + round-robin fashion. One Fujitsu chip supplies four > + GyroADC channels with data as it contains four ADCs > + on the chip and thus for 4-channel operation, single > + MB88101A is required. The Cx chipselect lines of the > + MB88101A connect directly to two CHS lines of the > + GyroADC, no demuxer is required. The data out line > + of each MB88101A connects to a shared input pin of > + the GyroADC. > + "ti,adcs7476" or "ti,adc121" or "adi,ad7476" > + - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, > + 15bit sampling, up to 8 channels can be sampled in > + round-robin fashion. One TI/ADI chip supplies single > + ADC channel with data, thus for 8-channel operation, > + 8 chips are required. A 3:8 chipselect demuxer is > + required to connect the nCS line of the TI/ADI chips > + to the GyroADC, while MISO line of each TI/ADI ADC > + connects to a shared input pin of the GyroADC. > + "maxim,max1162" or "maxim,max11100" > + - Maxim MAX1162 / Maxim MAX11100 compatible mode, > + 16bit sampling, up to 8 channels can be sampled in > + round-robin fashion. One Maxim chip supplies single > + ADC channel with data, thus for 8-channel operation, > + 8 chips are required. A 3:8 chipselect demuxer is > + required to connect the nCS line of the MAX chips > + to the GyroADC, while MISO line of each Maxim ADC > + connects to a shared input pin of the GyroADC. > +- reg: Should be the number of the analog input. Should be present > + for all ADCs except "fujitsu,mb88101a". > +- vref-supply: Reference to the channel reference voltage regulator. > + > +Example: > + vref_max1162: regulator-vref-max1162 { > + compatible = "regulator-fixed"; > + > + regulator-name = "MAX1162 Vref"; > + regulator-min-microvolt = <4096000>; > + regulator-max-microvolt = <4096000>; > + }; > + > + &adc { This wouldn't actually work unless you include something that defines '&adc'. Make this adc@e6e54000. With that, Acked-by: Rob Herring <robh@kernel.org> > + compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; > + reg = <0 0xe6e54000 0 64>; > + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>; > + clock-names = "fck", "if"; > + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; > + > + pinctrl-0 = <&adc_pins>; > + pinctrl-names = "default"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + adc@0 { > + reg = <0>; > + compatible = "maxim,max1162"; > + vref-supply = <&vref_max1162>; > + }; > + > + adc@1 { > + reg = <1>; > + compatible = "maxim,max1162"; > + vref-supply = <&vref_max1162>; > + }; > + }; > -- > 2.11.0 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 01/27/2017 11:26 PM, Rob Herring wrote: > On Tue, Jan 24, 2017 at 07:26:41PM +0100, Marek Vasut wrote: >> Add DT bindings for the Renesas RCar GyroADC block. This block is >> a simple 4/8-channel ADC which samples 12/15/24 bits of data every >> cycle from all channels. >> >> Signed-off-by: Marek Vasut <marek.vasut@gmail.com> >> Cc: Geert Uytterhoeven <geert+renesas@glider.be> >> Cc: Simon Horman <horms+renesas@verge.net.au> >> Cc: Jonathan Cameron <jic23@kernel.org> >> Cc: linux-renesas-soc@vger.kernel.org >> Cc: Wolfram Sang <wsa@the-dreams.de> >> Cc: Rob Herring <robh@kernel.org> >> Cc: devicetree@vger.kernel.org >> --- >> V8: - Sync the version with the 2/2 driver patch >> - Drop status prop from example >> - Add GyroADC block description >> - Enumerate the compatible string values >> - Make subnodes mandatory >> --- >> .../bindings/iio/adc/renesas,gyroadc.txt | 99 ++++++++++++++++++++++ >> 1 file changed, 99 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt >> >> diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt >> new file mode 100644 >> index 000000000000..7f9b3bd120a9 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt >> @@ -0,0 +1,99 @@ >> +* Renesas RCar GyroADC device driver >> + >> +The GyroADC block is a reduced SPI block with up to 8 chipselect lines, >> +which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs >> +are sampled by the GyroADC block in a round-robin fashion and the result >> +presented in the GyroADC registers. >> + >> +Required properties: >> +- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc". >> + The <soc-specific> should be one of: >> + renesas,r8a7791-gyroadc - for the GyroADC block present >> + in r8a7791 SoC >> + renesas,r8a7792-gyroadc - for the GyroADC with interrupt >> + block present in r8a7792 SoC >> +- reg: Address and length of the register set for the device >> +- clocks: References to all the clocks specified in the clock-names >> + property as specified in >> + Documentation/devicetree/bindings/clock/clock-bindings.txt. >> +- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block >> + clock, the "if" is the interface clock. >> +- power-domains: Must contain a reference to the PM domain, if available. >> +- #address-cells: Should be <1> (setting for the subnodes) for all ADCs >> + except for "fujitsu,mb88101a". Should be <0> (setting for >> + only subnode) for "fujitsu,mb88101a". >> +- #size-cells: Should be <0> (setting for the subnodes) >> + >> +Sub-nodes: >> +You must define subnode(s) which select the connected ADC type and reference >> +voltage for the GyroADC channels. >> + >> +Required properties for subnodes: >> +- compatible: Should be either of: >> + "fujitsu,mb88101a" >> + - Fujitsu MB88101A compatible mode, >> + 12bit sampling, up to 4 channels can be sampled in >> + round-robin fashion. One Fujitsu chip supplies four >> + GyroADC channels with data as it contains four ADCs >> + on the chip and thus for 4-channel operation, single >> + MB88101A is required. The Cx chipselect lines of the >> + MB88101A connect directly to two CHS lines of the >> + GyroADC, no demuxer is required. The data out line >> + of each MB88101A connects to a shared input pin of >> + the GyroADC. >> + "ti,adcs7476" or "ti,adc121" or "adi,ad7476" >> + - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, >> + 15bit sampling, up to 8 channels can be sampled in >> + round-robin fashion. One TI/ADI chip supplies single >> + ADC channel with data, thus for 8-channel operation, >> + 8 chips are required. A 3:8 chipselect demuxer is >> + required to connect the nCS line of the TI/ADI chips >> + to the GyroADC, while MISO line of each TI/ADI ADC >> + connects to a shared input pin of the GyroADC. >> + "maxim,max1162" or "maxim,max11100" >> + - Maxim MAX1162 / Maxim MAX11100 compatible mode, >> + 16bit sampling, up to 8 channels can be sampled in >> + round-robin fashion. One Maxim chip supplies single >> + ADC channel with data, thus for 8-channel operation, >> + 8 chips are required. A 3:8 chipselect demuxer is >> + required to connect the nCS line of the MAX chips >> + to the GyroADC, while MISO line of each Maxim ADC >> + connects to a shared input pin of the GyroADC. >> +- reg: Should be the number of the analog input. Should be present >> + for all ADCs except "fujitsu,mb88101a". >> +- vref-supply: Reference to the channel reference voltage regulator. >> + >> +Example: >> + vref_max1162: regulator-vref-max1162 { >> + compatible = "regulator-fixed"; >> + >> + regulator-name = "MAX1162 Vref"; >> + regulator-min-microvolt = <4096000>; >> + regulator-max-microvolt = <4096000>; >> + }; >> + >> + &adc { > > This wouldn't actually work unless you include something that defines > '&adc'. Make this adc@e6e54000. Fixed > With that, > > Acked-by: Rob Herring <robh@kernel.org> Cool, thanks
diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt new file mode 100644 index 000000000000..7f9b3bd120a9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt @@ -0,0 +1,99 @@ +* Renesas RCar GyroADC device driver + +The GyroADC block is a reduced SPI block with up to 8 chipselect lines, +which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs +are sampled by the GyroADC block in a round-robin fashion and the result +presented in the GyroADC registers. + +Required properties: +- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc". + The <soc-specific> should be one of: + renesas,r8a7791-gyroadc - for the GyroADC block present + in r8a7791 SoC + renesas,r8a7792-gyroadc - for the GyroADC with interrupt + block present in r8a7792 SoC +- reg: Address and length of the register set for the device +- clocks: References to all the clocks specified in the clock-names + property as specified in + Documentation/devicetree/bindings/clock/clock-bindings.txt. +- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block + clock, the "if" is the interface clock. +- power-domains: Must contain a reference to the PM domain, if available. +- #address-cells: Should be <1> (setting for the subnodes) for all ADCs + except for "fujitsu,mb88101a". Should be <0> (setting for + only subnode) for "fujitsu,mb88101a". +- #size-cells: Should be <0> (setting for the subnodes) + +Sub-nodes: +You must define subnode(s) which select the connected ADC type and reference +voltage for the GyroADC channels. + +Required properties for subnodes: +- compatible: Should be either of: + "fujitsu,mb88101a" + - Fujitsu MB88101A compatible mode, + 12bit sampling, up to 4 channels can be sampled in + round-robin fashion. One Fujitsu chip supplies four + GyroADC channels with data as it contains four ADCs + on the chip and thus for 4-channel operation, single + MB88101A is required. The Cx chipselect lines of the + MB88101A connect directly to two CHS lines of the + GyroADC, no demuxer is required. The data out line + of each MB88101A connects to a shared input pin of + the GyroADC. + "ti,adcs7476" or "ti,adc121" or "adi,ad7476" + - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, + 15bit sampling, up to 8 channels can be sampled in + round-robin fashion. One TI/ADI chip supplies single + ADC channel with data, thus for 8-channel operation, + 8 chips are required. A 3:8 chipselect demuxer is + required to connect the nCS line of the TI/ADI chips + to the GyroADC, while MISO line of each TI/ADI ADC + connects to a shared input pin of the GyroADC. + "maxim,max1162" or "maxim,max11100" + - Maxim MAX1162 / Maxim MAX11100 compatible mode, + 16bit sampling, up to 8 channels can be sampled in + round-robin fashion. One Maxim chip supplies single + ADC channel with data, thus for 8-channel operation, + 8 chips are required. A 3:8 chipselect demuxer is + required to connect the nCS line of the MAX chips + to the GyroADC, while MISO line of each Maxim ADC + connects to a shared input pin of the GyroADC. +- reg: Should be the number of the analog input. Should be present + for all ADCs except "fujitsu,mb88101a". +- vref-supply: Reference to the channel reference voltage regulator. + +Example: + vref_max1162: regulator-vref-max1162 { + compatible = "regulator-fixed"; + + regulator-name = "MAX1162 Vref"; + regulator-min-microvolt = <4096000>; + regulator-max-microvolt = <4096000>; + }; + + &adc { + compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; + reg = <0 0xe6e54000 0 64>; + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>; + clock-names = "fck", "if"; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + + pinctrl-0 = <&adc_pins>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + reg = <0>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + + adc@1 { + reg = <1>; + compatible = "maxim,max1162"; + vref-supply = <&vref_max1162>; + }; + };
Add DT bindings for the Renesas RCar GyroADC block. This block is a simple 4/8-channel ADC which samples 12/15/24 bits of data every cycle from all channels. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Simon Horman <horms+renesas@verge.net.au> Cc: Jonathan Cameron <jic23@kernel.org> Cc: linux-renesas-soc@vger.kernel.org Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Rob Herring <robh@kernel.org> Cc: devicetree@vger.kernel.org --- V8: - Sync the version with the 2/2 driver patch - Drop status prop from example - Add GyroADC block description - Enumerate the compatible string values - Make subnodes mandatory --- .../bindings/iio/adc/renesas,gyroadc.txt | 99 ++++++++++++++++++++++ 1 file changed, 99 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt