Message ID | 1484928317-19964-3-git-send-email-patrice.chotard@st.com |
---|---|
State | Superseded |
Delegated to: | Tom Rini |
Headers | show |
On Fri, Jan 20, 2017 at 5:05 PM, <patrice.chotard@st.com> wrote: > From: Patrice Chotard <patrice.chotard@st.com> Hi Patrice, just some minor issue in the commit message > This board is a 96Board based on STMicrolectronics > STiH410 soc: s/STMicrolectronics/STMicroelectronics/ s/soc/SoC/ maybe rework the whole sentence as: This is a 96Board compliant board based on ... > - 1GB DDR > - On-Board USB combo WiFi/Bluetooth RTL8723BU > with PCB soldered antenna > - Ethernet 1000-BaseT > - Sata s/Sata/SATA/ > - HDMI > - 2 x USB2 type A USB2.0 ? > - micro USB2 type AB maybe "1x USB2.0 type micro-AB" ? > - SD card slot > - High speed connector (SD/I2C/USB interfaces) > - Slow speed connector (UART/I2C/GPIO/SPI/PCM interfaces) According to 96Board spec, it is named "low speed connector" or "low speed expansion connector". Antonio > > Signed-off-by: Patrice Chotard <patrice.chotard@st.com> > --- > board/st/stih410-b2260/Kconfig | 19 +++++++++++++ > board/st/stih410-b2260/MAINTAINERS | 6 ++++ > board/st/stih410-b2260/Makefile | 8 ++++++ > board/st/stih410-b2260/board.c | 28 +++++++++++++++++++ > include/configs/stih410-b2260.h | 56 ++++++++++++++++++++++++++++++++++++++ > 5 files changed, 117 insertions(+) > create mode 100644 board/st/stih410-b2260/Kconfig > create mode 100644 board/st/stih410-b2260/MAINTAINERS > create mode 100644 board/st/stih410-b2260/Makefile > create mode 100644 board/st/stih410-b2260/board.c > create mode 100644 include/configs/stih410-b2260.h > > diff --git a/board/st/stih410-b2260/Kconfig b/board/st/stih410-b2260/Kconfig > new file mode 100644 > index 0000000..590add0 > --- /dev/null > +++ b/board/st/stih410-b2260/Kconfig > @@ -0,0 +1,19 @@ > +if TARGET_STIH410_B2260 > + > +config SYS_BOARD > + string > + default "stih410-b2260" > + > +config SYS_VENDOR > + string > + default "st" > + > +config SYS_SOC > + string > + default "stih410" > + > +config SYS_CONFIG_NAME > + string > + default "stih410-b2260" > + > +endif > diff --git a/board/st/stih410-b2260/MAINTAINERS b/board/st/stih410-b2260/MAINTAINERS > new file mode 100644 > index 0000000..e78c69a > --- /dev/null > +++ b/board/st/stih410-b2260/MAINTAINERS > @@ -0,0 +1,6 @@ > +STIH410-B2260 BOARD > +M: Patrice Chotard <patrice.chotard@st.com> > +S: Maintained > +F: board/st/stih410-b2260/ > +F: include/configs/stih410-b2260.h > +F: configs/stih410-b2260_defconfig > diff --git a/board/st/stih410-b2260/Makefile b/board/st/stih410-b2260/Makefile > new file mode 100644 > index 0000000..68a7903 > --- /dev/null > +++ b/board/st/stih410-b2260/Makefile > @@ -0,0 +1,8 @@ > +# > +# (C) Copyright 2017 > +# Patrice Chotard, <patrice.chotard@st.com> > +# > +# SPDX-License-Identifier: GPL-2.0+ > +# > + > +obj-y = board.o > diff --git a/board/st/stih410-b2260/board.c b/board/st/stih410-b2260/board.c > new file mode 100644 > index 0000000..0c06bca > --- /dev/null > +++ b/board/st/stih410-b2260/board.c > @@ -0,0 +1,28 @@ > +/* > + * Board init file for STiH410-B2260 > + * > + * (C) Copyright 2017 Patrice Chotard <patrice.chotard@st.com> > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#include <common.h> > + > +DECLARE_GLOBAL_DATA_PTR; > + > +int dram_init(void) > +{ > + gd->ram_size = PHYS_SDRAM_1_SIZE; > + return 0; > +} > + > +void dram_init_banksize(void) > +{ > + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; > + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; > +} > + > +int board_init(void) > +{ > + return 0; > +} > diff --git a/include/configs/stih410-b2260.h b/include/configs/stih410-b2260.h > new file mode 100644 > index 0000000..78103c6 > --- /dev/null > +++ b/include/configs/stih410-b2260.h > @@ -0,0 +1,56 @@ > +/* > + * (C) Copyright 2017 > + * Patrice Chotard, <patrice.chotard@st.com> > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#ifndef __CONFIG_H > +#define __CONFIG_H > + > +/* ram memory-related information */ > +#define CONFIG_NR_DRAM_BANKS 1 > +#define PHYS_SDRAM_1 0x40000000 > +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 > +#define PHYS_SDRAM_1_SIZE 0x3FE00000 > +#define CONFIG_SYS_TEXT_BASE 0x7D600000 > +#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM_1 /* default load addr */ > + > +#define CONFIG_BAUDRATE 115200 > + > +#define CONFIG_SYS_HZ_CLOCK 1000000000 /* 1 GHz */ > + > +/* Libraries */ > +#define CONFIG_MD5 > + > +#define CONFIG_BOOTARGS \ > + "console=ttyS0,115200 earlyprintk consoleblank=0 ignore_loglevel" > + > +/* Environment */ > +#define CONFIG_EXTRA_ENV_SETTINGS \ > + "board= B2260" \ > + "load_addr= #CONFIG_SYS_LOAD_ADDR \0" > + > +#define CONFIG_ENV_IS_NOWHERE > +#define CONFIG_ENV_SIZE 0x4000 > +#define CONFIG_SYS_NO_FLASH > + > +/* Extra Commands */ > +#define CONFIG_CMD_ASKENV > + > +/* Size of malloc() pool */ > +#define CONFIG_SYS_MALLOC_LEN 0x1800000 > +#define CONFIG_SYS_GBL_DATA_SIZE 1024 /* Global data structures */ > +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - \ > + CONFIG_SYS_MALLOC_LEN - \ > + CONFIG_SYS_GBL_DATA_SIZE) > + > +/* Monitor Command Prompt */ > +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ > + > +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ > +#define CONFIG_SYS_MAX_FLASH_BANKS 1 > + > +#define CONFIG_SKIP_LOWLEVEL_INIT > + > +#endif /* __CONFIG_H */ > -- > 1.9.1 > > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot
Hi Antonio On 02/02/2017 10:02 AM, Antonio Borneo wrote: > On Fri, Jan 20, 2017 at 5:05 PM, <patrice.chotard@st.com> wrote: >> From: Patrice Chotard <patrice.chotard@st.com> > > Hi Patrice, > > just some minor issue in the commit message > >> This board is a 96Board based on STMicrolectronics >> STiH410 soc: > > s/STMicrolectronics/STMicroelectronics/ > s/soc/SoC/ i will fix it > > maybe rework the whole sentence as: > This is a 96Board compliant board based on ... Ok > >> - 1GB DDR >> - On-Board USB combo WiFi/Bluetooth RTL8723BU >> with PCB soldered antenna >> - Ethernet 1000-BaseT >> - Sata > > s/Sata/SATA/ Ok > >> - HDMI >> - 2 x USB2 type A > > USB2.0 ? I will fix it > >> - micro USB2 type AB > > maybe "1x USB2.0 type micro-AB" ? Ok > >> - SD card slot >> - High speed connector (SD/I2C/USB interfaces) >> - Slow speed connector (UART/I2C/GPIO/SPI/PCM interfaces) > > According to 96Board spec, it is named "low speed connector" or "low > speed expansion connector". I will fix it > > Antonio Thanks for reviewing > >> >> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> >> --- >> board/st/stih410-b2260/Kconfig | 19 +++++++++++++ >> board/st/stih410-b2260/MAINTAINERS | 6 ++++ >> board/st/stih410-b2260/Makefile | 8 ++++++ >> board/st/stih410-b2260/board.c | 28 +++++++++++++++++++ >> include/configs/stih410-b2260.h | 56 ++++++++++++++++++++++++++++++++++++++ >> 5 files changed, 117 insertions(+) >> create mode 100644 board/st/stih410-b2260/Kconfig >> create mode 100644 board/st/stih410-b2260/MAINTAINERS >> create mode 100644 board/st/stih410-b2260/Makefile >> create mode 100644 board/st/stih410-b2260/board.c >> create mode 100644 include/configs/stih410-b2260.h >> >> diff --git a/board/st/stih410-b2260/Kconfig b/board/st/stih410-b2260/Kconfig >> new file mode 100644 >> index 0000000..590add0 >> --- /dev/null >> +++ b/board/st/stih410-b2260/Kconfig >> @@ -0,0 +1,19 @@ >> +if TARGET_STIH410_B2260 >> + >> +config SYS_BOARD >> + string >> + default "stih410-b2260" >> + >> +config SYS_VENDOR >> + string >> + default "st" >> + >> +config SYS_SOC >> + string >> + default "stih410" >> + >> +config SYS_CONFIG_NAME >> + string >> + default "stih410-b2260" >> + >> +endif >> diff --git a/board/st/stih410-b2260/MAINTAINERS b/board/st/stih410-b2260/MAINTAINERS >> new file mode 100644 >> index 0000000..e78c69a >> --- /dev/null >> +++ b/board/st/stih410-b2260/MAINTAINERS >> @@ -0,0 +1,6 @@ >> +STIH410-B2260 BOARD >> +M: Patrice Chotard <patrice.chotard@st.com> >> +S: Maintained >> +F: board/st/stih410-b2260/ >> +F: include/configs/stih410-b2260.h >> +F: configs/stih410-b2260_defconfig >> diff --git a/board/st/stih410-b2260/Makefile b/board/st/stih410-b2260/Makefile >> new file mode 100644 >> index 0000000..68a7903 >> --- /dev/null >> +++ b/board/st/stih410-b2260/Makefile >> @@ -0,0 +1,8 @@ >> +# >> +# (C) Copyright 2017 >> +# Patrice Chotard, <patrice.chotard@st.com> >> +# >> +# SPDX-License-Identifier: GPL-2.0+ >> +# >> + >> +obj-y = board.o >> diff --git a/board/st/stih410-b2260/board.c b/board/st/stih410-b2260/board.c >> new file mode 100644 >> index 0000000..0c06bca >> --- /dev/null >> +++ b/board/st/stih410-b2260/board.c >> @@ -0,0 +1,28 @@ >> +/* >> + * Board init file for STiH410-B2260 >> + * >> + * (C) Copyright 2017 Patrice Chotard <patrice.chotard@st.com> >> + * >> + * SPDX-License-Identifier: GPL-2.0+ >> + */ >> + >> +#include <common.h> >> + >> +DECLARE_GLOBAL_DATA_PTR; >> + >> +int dram_init(void) >> +{ >> + gd->ram_size = PHYS_SDRAM_1_SIZE; >> + return 0; >> +} >> + >> +void dram_init_banksize(void) >> +{ >> + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; >> + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; >> +} >> + >> +int board_init(void) >> +{ >> + return 0; >> +} >> diff --git a/include/configs/stih410-b2260.h b/include/configs/stih410-b2260.h >> new file mode 100644 >> index 0000000..78103c6 >> --- /dev/null >> +++ b/include/configs/stih410-b2260.h >> @@ -0,0 +1,56 @@ >> +/* >> + * (C) Copyright 2017 >> + * Patrice Chotard, <patrice.chotard@st.com> >> + * >> + * SPDX-License-Identifier: GPL-2.0+ >> + */ >> + >> +#ifndef __CONFIG_H >> +#define __CONFIG_H >> + >> +/* ram memory-related information */ >> +#define CONFIG_NR_DRAM_BANKS 1 >> +#define PHYS_SDRAM_1 0x40000000 >> +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 >> +#define PHYS_SDRAM_1_SIZE 0x3FE00000 >> +#define CONFIG_SYS_TEXT_BASE 0x7D600000 >> +#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM_1 /* default load addr */ >> + >> +#define CONFIG_BAUDRATE 115200 >> + >> +#define CONFIG_SYS_HZ_CLOCK 1000000000 /* 1 GHz */ >> + >> +/* Libraries */ >> +#define CONFIG_MD5 >> + >> +#define CONFIG_BOOTARGS \ >> + "console=ttyS0,115200 earlyprintk consoleblank=0 ignore_loglevel" >> + >> +/* Environment */ >> +#define CONFIG_EXTRA_ENV_SETTINGS \ >> + "board= B2260" \ >> + "load_addr= #CONFIG_SYS_LOAD_ADDR \0" >> + >> +#define CONFIG_ENV_IS_NOWHERE >> +#define CONFIG_ENV_SIZE 0x4000 >> +#define CONFIG_SYS_NO_FLASH >> + >> +/* Extra Commands */ >> +#define CONFIG_CMD_ASKENV >> + >> +/* Size of malloc() pool */ >> +#define CONFIG_SYS_MALLOC_LEN 0x1800000 >> +#define CONFIG_SYS_GBL_DATA_SIZE 1024 /* Global data structures */ >> +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - \ >> + CONFIG_SYS_MALLOC_LEN - \ >> + CONFIG_SYS_GBL_DATA_SIZE) >> + >> +/* Monitor Command Prompt */ >> +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ >> + >> +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ >> +#define CONFIG_SYS_MAX_FLASH_BANKS 1 >> + >> +#define CONFIG_SKIP_LOWLEVEL_INIT >> + >> +#endif /* __CONFIG_H */ >> -- >> 1.9.1 >> >> _______________________________________________ >> U-Boot mailing list >> U-Boot@lists.denx.de >> http://lists.denx.de/mailman/listinfo/u-boot
diff --git a/board/st/stih410-b2260/Kconfig b/board/st/stih410-b2260/Kconfig new file mode 100644 index 0000000..590add0 --- /dev/null +++ b/board/st/stih410-b2260/Kconfig @@ -0,0 +1,19 @@ +if TARGET_STIH410_B2260 + +config SYS_BOARD + string + default "stih410-b2260" + +config SYS_VENDOR + string + default "st" + +config SYS_SOC + string + default "stih410" + +config SYS_CONFIG_NAME + string + default "stih410-b2260" + +endif diff --git a/board/st/stih410-b2260/MAINTAINERS b/board/st/stih410-b2260/MAINTAINERS new file mode 100644 index 0000000..e78c69a --- /dev/null +++ b/board/st/stih410-b2260/MAINTAINERS @@ -0,0 +1,6 @@ +STIH410-B2260 BOARD +M: Patrice Chotard <patrice.chotard@st.com> +S: Maintained +F: board/st/stih410-b2260/ +F: include/configs/stih410-b2260.h +F: configs/stih410-b2260_defconfig diff --git a/board/st/stih410-b2260/Makefile b/board/st/stih410-b2260/Makefile new file mode 100644 index 0000000..68a7903 --- /dev/null +++ b/board/st/stih410-b2260/Makefile @@ -0,0 +1,8 @@ +# +# (C) Copyright 2017 +# Patrice Chotard, <patrice.chotard@st.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y = board.o diff --git a/board/st/stih410-b2260/board.c b/board/st/stih410-b2260/board.c new file mode 100644 index 0000000..0c06bca --- /dev/null +++ b/board/st/stih410-b2260/board.c @@ -0,0 +1,28 @@ +/* + * Board init file for STiH410-B2260 + * + * (C) Copyright 2017 Patrice Chotard <patrice.chotard@st.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> + +DECLARE_GLOBAL_DATA_PTR; + +int dram_init(void) +{ + gd->ram_size = PHYS_SDRAM_1_SIZE; + return 0; +} + +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; +} + +int board_init(void) +{ + return 0; +} diff --git a/include/configs/stih410-b2260.h b/include/configs/stih410-b2260.h new file mode 100644 index 0000000..78103c6 --- /dev/null +++ b/include/configs/stih410-b2260.h @@ -0,0 +1,56 @@ +/* + * (C) Copyright 2017 + * Patrice Chotard, <patrice.chotard@st.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* ram memory-related information */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM_1 0x40000000 +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define PHYS_SDRAM_1_SIZE 0x3FE00000 +#define CONFIG_SYS_TEXT_BASE 0x7D600000 +#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM_1 /* default load addr */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_HZ_CLOCK 1000000000 /* 1 GHz */ + +/* Libraries */ +#define CONFIG_MD5 + +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk consoleblank=0 ignore_loglevel" + +/* Environment */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "board= B2260" \ + "load_addr= #CONFIG_SYS_LOAD_ADDR \0" + +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_SYS_NO_FLASH + +/* Extra Commands */ +#define CONFIG_CMD_ASKENV + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN 0x1800000 +#define CONFIG_SYS_GBL_DATA_SIZE 1024 /* Global data structures */ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - \ + CONFIG_SYS_MALLOC_LEN - \ + CONFIG_SYS_GBL_DATA_SIZE) + +/* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 + +#define CONFIG_SKIP_LOWLEVEL_INIT + +#endif /* __CONFIG_H */