Patchwork [U-Boot,v3,ARM] at91: Add support for taskit AT91SAM9G20 boards

login
register
mail settings
Submitter Achim Ehrlich
Date April 20, 2010, 3:12 p.m.
Message ID <1271776361-31003-1-git-send-email-aehrlich@taskit.de>
Download mbox | patch
Permalink /patch/71772/
State Changes Requested
Delegated to: Reinhard Meyer
Headers show

Comments

Achim Ehrlich - April 20, 2010, 3:12 p.m.
This adds support for the AT91SAM9G20 boards by taskit GmbH.
Both boards, Stamp9G20 and PortuxG20, are integrated in one file.
PortuxG20 is basically a SBC built around Stam9G20.

Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
---
 MAINTAINERS                        |    5 +
 MAKEALL                            |    1 +
 Makefile                           |    4 +
 board/taskit/stamp9G20/Makefile    |   50 +++++++++
 board/taskit/stamp9G20/config.mk   |    1 +
 board/taskit/stamp9G20/stamp9G20.c |  199 ++++++++++++++++++++++++++++++++++++
 include/configs/stamp9G20.h        |  183 +++++++++++++++++++++++++++++++++
 7 files changed, 443 insertions(+), 0 deletions(-)
 create mode 100644 board/taskit/stamp9G20/Makefile
 create mode 100644 board/taskit/stamp9G20/config.mk
 create mode 100644 board/taskit/stamp9G20/stamp9G20.c
 create mode 100644 include/configs/stamp9G20.h
Achim Ehrlich - May 20, 2010, 7:12 a.m.
Hello Tom,

are there still objections to our patch or has it just got forgotten?

Kind regards


Achim
Reinhard Meyer - Aug. 20, 2010, 12:05 p.m.
Dear Achim Ehrlich,

> are there still objections to our patch or has it just got forgotten?

Just not dealt with (#error: no custodian) :)

Can you please rebase,
and use boards.cfg instead of global Makefile?

Best Regards,
Reinhard

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 0658bc3..2052d74 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -136,6 +136,11 @@  Jon Diekema <jon.diekema@smiths-aerospace.com>
 
 	sbc8260		MPC8260
 
+Achim Ehrlich <aehrlich@taskit.de>
+
+	Stamp9G20	AT91SAM9G20
+	PortuxG20	AT91SAM9G20
+
 Dirk Eibach <eibach@gdsys.de>
 
 	devconcenter	PPC460EX
diff --git a/MAKEALL b/MAKEALL
index a88c31e..3102085 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -671,6 +671,7 @@  LIST_at91="			\
 	pm9261			\
 	pm9263			\
 	SBC35_A9G20		\
+	stamp9G20		\
 	TNY_A9260		\
 	TNY_A9G20		\
 "
diff --git a/Makefile b/Makefile
index 4532550..9480e99 100644
--- a/Makefile
+++ b/Makefile
@@ -2883,6 +2883,10 @@  TNY_A9260_config	:	unconfig
 	@echo "#define CONFIG_$(@:_config=) 1" >$(obj)include/config.h
 	@$(MKCONFIG) -a tny_a9260 arm arm926ejs tny_a9260 calao at91
 
+portuxG20_config \
+stamp9G20_config	:	unconfig
+	@$(MKCONFIG) -t $(@:_config=) stamp9G20 arm arm926ejs stamp9G20 taskit at91
+
 ########################################################################
 ## ARM Integrator boards - see doc/README-integrator for more info.
 integratorap_config	\
diff --git a/board/taskit/stamp9G20/Makefile b/board/taskit/stamp9G20/Makefile
new file mode 100644
index 0000000..191fb8e
--- /dev/null
+++ b/board/taskit/stamp9G20/Makefile
@@ -0,0 +1,50 @@ 
+#
+# (C) Copyright 2010
+# Achim Ehrlich, taskit GmbH, aehrlich@taskit.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS-y	+= stamp9G20.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/taskit/stamp9G20/config.mk b/board/taskit/stamp9G20/config.mk
new file mode 100644
index 0000000..ff2cfd1
--- /dev/null
+++ b/board/taskit/stamp9G20/config.mk
@@ -0,0 +1 @@ 
+TEXT_BASE = 0x23f00000
diff --git a/board/taskit/stamp9G20/stamp9G20.c b/board/taskit/stamp9G20/stamp9G20.c
new file mode 100644
index 0000000..6beb1cd
--- /dev/null
+++ b/board/taskit/stamp9G20/stamp9G20.c
@@ -0,0 +1,199 @@ 
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ * 
+ * (C) Copyright 2010
+ * Achim Ehrlich <aehrlich@taskit.de>
+ * taskit GmbH <www.taskit.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/at91sam9260.h>
+#include <asm/arch/at91_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/at91_pio.h>
+#include <asm/arch/io.h>
+#include <asm/arch/hardware.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
+#include <net.h>
+#endif
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+#ifdef CONFIG_CMD_NAND
+static void stamp9G20_nand_hw_init(void)
+{
+	unsigned long csa;
+	at91_smc_t 	*smc 	= (at91_smc_t *) AT91_SMC_BASE;
+	at91_matrix_t 	*matrix = (at91_matrix_t *) AT91_MATRIX_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+
+	/* Enable CS3 */
+	csa = readl(&matrix->csa) | AT91_MATRIX_CSA_EBI_CS3A;
+	writel(csa, &matrix->csa);
+
+	/* Configure SMC CS3 for NAND/SmartMedia */
+	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+		AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+		&smc->cs[3].setup);
+
+	writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
+		AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
+		&smc->cs[3].pulse);
+
+	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+		&smc->cs[3].cycle);
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+		AT91_SMC_MODE_EXNW_DISABLE | AT91_SMC_MODE_DBW_8 |
+		AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode);
+
+	writel(1 << AT91SAM9260_ID_PIOC, &pmc->pcer);
+
+	/* Configure RDY/BSY */
+	at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+
+	/* Enable NandFlash */
+	at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+}
+#endif
+
+#ifdef CONFIG_MACB
+static void stamp9G20_macb_hw_init(void)
+{
+	unsigned long 	erstl;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pio_t	*pio	= (at91_pio_t *) AT91_PIO_BASE;
+	at91_rstc_t	*rstc	= (at91_rstc_t *) AT91_RSTC_BASE;
+	
+	/* Enable MACB Chip, this is the enable PIN on Stamp Adaptor*/
+	at91_set_pio_output(CONFIG_SYS_PHY_ENABLE_PIN, 0);
+
+	/* Enable clock */
+	writel(1 << AT91SAM9260_ID_EMAC, &pmc->pcer);
+
+	/*
+	 * Disable pull-up on:
+	 *	RXDV (PA17) => PHY normal mode (not Test mode)
+	 *	ERX0 (PA14) => PHY ADDR0
+	 *	ERX1 (PA15) => PHY ADDR1
+	 *	ERX2 (PA25) => PHY ADDR2
+	 *	ERX3 (PA26) => PHY ADDR3
+	 *	ECRS (PA28) => PHY ADDR4  => PHYADDR = 0x0
+	 *
+	 * PHY has internal pull-down
+	 */
+	writel((1 << 14) | (1 << 15) | (1 << 17) |
+			(1 << 25), &pio->pioa.pudr);
+
+	erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
+
+	/* Need to reset PHY -> 500ms reset */
+	writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(0x0D) |
+		AT91_RSTC_MR_URSTEN, &rstc->mr);
+
+	writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
+	/* Wait for end hardware reset */
+	while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL))
+		;
+
+	/* Restore NRST value */
+	writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN, &rstc->mr);
+
+	/* Re-enable pull-up */
+	writel((1 << 14) | (1 << 15) | (1 << 17) |
+			(1 << 25), &pio->pioa.puer);
+
+	at91_macb_hw_init();
+}
+#endif
+
+int board_init(void)
+{
+	/* Enable Ctrlc */
+	console_init_f();
+
+#ifdef CONFIG_MK_portuxG20
+	gd->bd->bi_arch_number = MACH_TYPE_PORTUXG20;
+#else
+	gd->bd->bi_arch_number = MACH_TYPE_STAMP9G20;
+#endif
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_MK_portuxG20
+	at91_set_pio_output(CONFIG_SYS_RS232_ENABLE_PIN, 1);
+	at91_set_pio_output(CONFIG_SYS_LED_RED_PIN, 1);
+#endif
+
+	at91_serial_hw_init();
+#ifdef CONFIG_CMD_NAND
+	stamp9G20_nand_hw_init();
+#endif
+#ifdef CONFIG_HAS_DATAFLASH
+	at91_spi0_hw_init((1 << 0) || (1 << 1));
+#endif
+#ifdef CONFIG_MACB
+	stamp9G20_macb_hw_init();
+#endif
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE
+			, CONFIG_SYS_SDRAM_SIZE);
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+#ifdef CONFIG_MACB
+	/*
+	 * Initialize ethernet HW addr prior to starting Linux,
+	 * needed for nfsroot
+	 */
+	eth_init(gd->bd);
+#endif
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_MACB
+	rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x00);
+#endif
+	return rc;
+}
diff --git a/include/configs/stamp9G20.h b/include/configs/stamp9G20.h
new file mode 100644
index 0000000..262a5de
--- /dev/null
+++ b/include/configs/stamp9G20.h
@@ -0,0 +1,183 @@ 
+/*
+ * (C) 2010 Achim Ehrlich <aehrlich@taskit.de>
+ * taskit GmbH <www.taskit.de>
+ *
+ * Configuation settings for the Stamp9G20 CPU module.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_ARM926EJS	1
+#define CONFIG_AT91SAM9G20	1
+#define CONFIG_ARCH_CPU_INIT
+#undef CONFIG_USE_IRQ
+/* ARM asynchronous clock */
+/* 18.432 MHz crystal */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	18432000
+/* 1ms resolution */
+#define CONFIG_SYS_HZ		1000
+
+/* enable passing of ATAGs */
+#define CONFIG_CMDLINE_TAG	1
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG	1
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_SKIP_RELOCATE_UBOOT
+
+/* pad the watchdog */
+
+#define CONFIG_AT91SAM9_WATCHDOG
+#define CONFIG_HW_WATCHDOG
+
+/*
+ * Hardware drivers
+ */
+
+#define CONFIG_AT91_GPIO
+#define CONFIG_SYS_LED_RED_PIN		AT91_PIO_PORTC, 5
+#define CONFIG_ATMEL_USART		1
+#define CONFIG_SYS_RS232_ENABLE_PIN	AT91_PIO_PORTC, 9
+
+/* USART 3 is DBGU */
+#define CONFIG_USART3		1
+
+#define CONFIG_BOOTDELAY	3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE	1
+#define CONFIG_BOOTP_BOOTPATH		1
+#define CONFIG_BOOTP_GATEWAY		1
+#define CONFIG_BOOTP_HOSTNAME		1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_PING		1
+#define CONFIG_CMD_DHCP		1
+#define CONFIG_CMD_NAND		1
+#define CONFIG_CMD_USB		1
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		0x20000000
+#define CONFIG_SYS_SDRAM_SIZE		0x08000000
+
+/* DataFlash */
+#undef CONFIG_ATMEL_DATAFLASH_SPI
+#undef CONFIG_HAS_DATAFLASH
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE		1
+#define CONFIG_SYS_NAND_BASE			0x40000000
+#define CONFIG_SYS_NAND_DBW_8			1
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE		(1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE		(1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN		AT91_PIO_PORTC, 14
+#define CONFIG_SYS_NAND_READY_PIN		AT91_PIO_PORTC, 13
+/* needed for nand_util.c */
+#define CONFIG_SYS_64BIT_VSPRINTF
+#endif
+
+/* NOR flash - no real flash on this board */
+#define CONFIG_SYS_NO_FLASH		1
+
+/* Ethernet */
+#define CONFIG_MACB			1
+#define CONFIG_RMII			1
+#define CONFIG_NET_MULTI		1
+#define CONFIG_NET_RETRY_COUNT		20
+#define CONFIG_RESET_PHY_R		1
+#define CONFIG_SYS_PHY_ENABLE_PIN	AT91_PIO_PORTA, 26
+
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_OHCI_NEW		1
+#define CONFIG_DOS_PARTITION		1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT	1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE	0x00500000
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"at91sam9260"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
+#define CONFIG_USB_STORAGE		1
+#define CONFIG_CMD_FAT			1
+
+#define CONFIG_SYS_LOAD_ADDR		0x22000000
+
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		0x23e00000
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND	1
+#define CONFIG_ENV_OFFSET		0x60000
+#define CONFIG_ENV_OFFSET_REDUND	0x80000
+#define CONFIG_ENV_SIZE		0x20000		/* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND	"run sdboot"
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"mtdparts=mtdparts=atmel_nand:128k(bootstrap)ro,"		\
+				"256k(uboot)ro,128k(env1)ro,"		\
+				"128k(env2)ro,2M(linux),-(root)rw\0" 	\
+	"sdboot=setenv bootargs ${basicargs} mem=${ramsize} "		\
+		"${mtdparts} root=/dev/mmcblk0p1 rootdelay=1; "		\
+		"nand read 0x22000000 0xA0000 0x200000; "		\
+		"bootm 22000000\0"					\
+	"flashboot=setenv bootargs ${basicargs} ${mtdparts} "		\
+		"root=/dev/mtdblock5 rootfstype=jffs2; "		\
+		"nand read 0x22000000 0xA0000 0x200000; "		\
+		"bootm 22000000\0"					\
+	"ramsize=64M\0"							\
+	"basicargs=console=ttyS0,115200\0"				\
+	""
+
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
+
+#define CONFIG_SYS_PROMPT	"U-Boot> "
+#define CONFIG_SYS_CBSIZE	256
+#define CONFIG_SYS_MAXARGS	16
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP	1
+#define CONFIG_CMDLINE_EDITING	1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN	ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
+#define CONFIG_SYS_GBL_DATA_SIZE 128	/* 128 bytes for initial data */
+
+#define CONFIG_STACKSIZE	(32*1024)	/* regular stack */
+
+#ifdef CONFIG_USE_IRQ
+#error CONFIG_USE_IRQ not supported
+#endif
+
+#endif