@@ -17,6 +17,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/of_gpio.h>
+#include <linux/of_pci.h>
#include <linux/pci.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
@@ -63,11 +64,14 @@
#define LINK_UP BIT(16)
#define DRA7XX_CPU_TO_BUS_ADDR 0x0FFFFFFF
+#define EXP_CAP_ID_OFFSET 0x70
+
struct dra7xx_pcie {
struct pcie_port pp;
void __iomem *base; /* DT ti_conf */
int phy_count; /* DT phy-names count */
struct phy **phy;
+ int link_gen;
};
#define to_dra7xx_pcie(x) container_of((x), struct dra7xx_pcie, pp)
@@ -96,12 +100,33 @@ static int dra7xx_pcie_establish_link(struct dra7xx_pcie *dra7xx)
struct pcie_port *pp = &dra7xx->pp;
struct device *dev = pp->dev;
u32 reg;
+ u32 exp_cap_off = EXP_CAP_ID_OFFSET;
if (dw_pcie_link_up(pp)) {
dev_err(dev, "link is already up\n");
return 0;
}
+ if (dra7xx->link_gen == 1) {
+ dw_pcie_cfg_read(pp->dbi_base + exp_cap_off + PCI_EXP_LNKCAP,
+ 4, ®);
+ if ((reg & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_2_5GB) {
+ reg &= ~((u32)PCI_EXP_LNKCAP_SLS);
+ reg |= PCI_EXP_LNKCAP_SLS_2_5GB;
+ dw_pcie_cfg_write(pp->dbi_base + exp_cap_off +
+ PCI_EXP_LNKCAP, 4, reg);
+ }
+
+ dw_pcie_cfg_read(pp->dbi_base + exp_cap_off + PCI_EXP_LNKCTL2,
+ 2, ®);
+ if ((reg & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_2_5GB) {
+ reg &= ~((u32)PCI_EXP_LNKCAP_SLS);
+ reg |= PCI_EXP_LNKCAP_SLS_2_5GB;
+ dw_pcie_cfg_write(pp->dbi_base + exp_cap_off +
+ PCI_EXP_LNKCTL2, 2, reg);
+ }
+ }
+
reg = dra7xx_pcie_readl(dra7xx, PCIECTRL_DRA7XX_CONF_DEVICE_CMD);
reg |= LTSSM_EN;
dra7xx_pcie_writel(dra7xx, PCIECTRL_DRA7XX_CONF_DEVICE_CMD, reg);
@@ -397,6 +422,10 @@ static int __init dra7xx_pcie_probe(struct platform_device *pdev)
reg &= ~LTSSM_EN;
dra7xx_pcie_writel(dra7xx, PCIECTRL_DRA7XX_CONF_DEVICE_CMD, reg);
+ dra7xx->link_gen = of_pci_get_max_link_speed(np);
+ if (dra7xx->link_gen < 0 || dra7xx->link_gen > 2)
+ dra7xx->link_gen = 2;
+
ret = dra7xx_add_pcie_port(dra7xx, pdev);
if (ret < 0)
goto err_gpio;
PCIe in AM57x/DRA7x devices is by default configured to work in GEN2 mode. However there may be situations when working in GEN1 mode is desired. One example is limitation i925 (PCIe GEN2 mode not supported at junction temperatures < 0C). Add support to force Root Complex to work in GEN1 mode if so desired, but don't force GEN1 mode on any board just yet. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- drivers/pci/controller/pci-dra7xx.c | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+)