@@ -4,4 +4,5 @@
obj-$(CONFIG_QCOM_EMAC) += qcom-emac.o
-qcom-emac-objs := emac.o emac-mac.o emac-phy.o emac-sgmii.o
+qcom-emac-objs := emac.o emac-mac.o emac-phy.o emac-sgmii.o \
+ emac-sgmii-fsm9900.o emac-sgmii-qdf2432.o
new file mode 100644
@@ -0,0 +1,245 @@
+/* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. FSM9900 EMAC SGMII Controller driver.
+ */
+
+#include <linux/iopoll.h>
+#include "emac.h"
+
+/* EMAC_QSERDES register offsets */
+#define EMAC_QSERDES_COM_SYS_CLK_CTRL 0x0000
+#define EMAC_QSERDES_COM_PLL_CNTRL 0x0014
+#define EMAC_QSERDES_COM_PLL_IP_SETI 0x0018
+#define EMAC_QSERDES_COM_PLL_CP_SETI 0x0024
+#define EMAC_QSERDES_COM_PLL_IP_SETP 0x0028
+#define EMAC_QSERDES_COM_PLL_CP_SETP 0x002c
+#define EMAC_QSERDES_COM_SYSCLK_EN_SEL 0x0038
+#define EMAC_QSERDES_COM_RESETSM_CNTRL 0x0040
+#define EMAC_QSERDES_COM_PLLLOCK_CMP1 0x0044
+#define EMAC_QSERDES_COM_PLLLOCK_CMP2 0x0048
+#define EMAC_QSERDES_COM_PLLLOCK_CMP3 0x004c
+#define EMAC_QSERDES_COM_PLLLOCK_CMP_EN 0x0050
+#define EMAC_QSERDES_COM_DEC_START1 0x0064
+#define EMAC_QSERDES_COM_DIV_FRAC_START1 0x0098
+#define EMAC_QSERDES_COM_DIV_FRAC_START2 0x009c
+#define EMAC_QSERDES_COM_DIV_FRAC_START3 0x00a0
+#define EMAC_QSERDES_COM_DEC_START2 0x00a4
+#define EMAC_QSERDES_COM_PLL_CRCTRL 0x00ac
+#define EMAC_QSERDES_COM_RESET_SM 0x00bc
+#define EMAC_QSERDES_TX_BIST_MODE_LANENO 0x0100
+#define EMAC_QSERDES_TX_TX_EMP_POST1_LVL 0x0108
+#define EMAC_QSERDES_TX_TX_DRV_LVL 0x010c
+#define EMAC_QSERDES_TX_LANE_MODE 0x0150
+#define EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN 0x0170
+#define EMAC_QSERDES_RX_CDR_CONTROL 0x0200
+#define EMAC_QSERDES_RX_CDR_CONTROL2 0x0210
+#define EMAC_QSERDES_RX_RX_EQ_GAIN12 0x0230
+
+/* EMAC_SGMII register offsets */
+#define EMAC_SGMII_PHY_SERDES_START 0x0000
+#define EMAC_SGMII_PHY_CMN_PWR_CTRL 0x0004
+#define EMAC_SGMII_PHY_RX_PWR_CTRL 0x0008
+#define EMAC_SGMII_PHY_TX_PWR_CTRL 0x000C
+#define EMAC_SGMII_PHY_LANE_CTRL1 0x0018
+#define EMAC_SGMII_PHY_CDR_CTRL0 0x0058
+#define EMAC_SGMII_PHY_POW_DWN_CTRL0 0x0080
+#define EMAC_SGMII_PHY_INTERRUPT_MASK 0x00b4
+
+#define PLL_IPSETI(x) ((x) & 0x3f)
+
+#define PLL_CPSETI(x) ((x) & 0xff)
+
+#define PLL_IPSETP(x) ((x) & 0x3f)
+
+#define PLL_CPSETP(x) ((x) & 0x1f)
+
+#define PLL_RCTRL(x) (((x) & 0xf) << 4)
+#define PLL_CCTRL(x) ((x) & 0xf)
+
+#define LANE_MODE(x) ((x) & 0x1f)
+
+#define SYSCLK_CM BIT(4)
+#define SYSCLK_AC_COUPLE BIT(3)
+
+#define OCP_EN BIT(5)
+#define PLL_DIV_FFEN BIT(2)
+#define PLL_DIV_ORD BIT(1)
+
+#define SYSCLK_SEL_CMOS BIT(3)
+
+#define FRQ_TUNE_MODE BIT(4)
+
+#define PLLLOCK_CMP_EN BIT(0)
+
+#define DEC_START1_MUX BIT(7)
+#define DEC_START1(x) ((x) & 0x7f)
+
+#define DIV_FRAC_START_MUX BIT(7)
+#define DIV_FRAC_START(x) ((x) & 0x7f)
+
+#define DIV_FRAC_START3_MUX BIT(4)
+#define DIV_FRAC_START3(x) ((x) & 0xf)
+
+#define DEC_START2_MUX BIT(1)
+#define DEC_START2 BIT(0)
+
+#define READY BIT(5)
+
+#define TX_EMP_POST1_LVL_MUX BIT(5)
+#define TX_EMP_POST1_LVL(x) ((x) & 0x1f)
+
+#define TX_DRV_LVL_MUX BIT(4)
+#define TX_DRV_LVL(x) ((x) & 0xf)
+
+#define EMP_EN_MUX BIT(1)
+#define EMP_EN BIT(0)
+
+#define SECONDORDERENABLE BIT(6)
+#define FIRSTORDER_THRESH(x) (((x) & 0x7) << 3)
+#define SECONDORDERGAIN(x) ((x) & 0x7)
+
+#define RX_EQ_GAIN2(x) (((x) & 0xf) << 4)
+#define RX_EQ_GAIN1(x) ((x) & 0xf)
+
+#define SERDES_START BIT(0)
+
+#define BIAS_EN BIT(6)
+#define PLL_EN BIT(5)
+#define SYSCLK_EN BIT(4)
+#define CLKBUF_L_EN BIT(3)
+#define PLL_TXCLK_EN BIT(1)
+#define PLL_RXCLK_EN BIT(0)
+
+#define L0_RX_SIGDET_EN BIT(7)
+#define L0_RX_TERM_MODE(x) (((x) & 3) << 4)
+#define L0_RX_I_EN BIT(1)
+
+#define L0_TX_EN BIT(5)
+#define L0_CLKBUF_EN BIT(4)
+#define L0_TRAN_BIAS_EN BIT(1)
+
+#define L0_RX_EQUALIZE_ENABLE BIT(6)
+#define L0_RESET_TSYNC_EN BIT(4)
+#define L0_DRV_LVL(x) ((x) & 0xf)
+
+#define PWRDN_B BIT(0)
+#define CDR_MAX_CNT(x) ((x) & 0xff)
+
+#define PLLLOCK_CMP(x) ((x) & 0xff)
+
+#define SERDES_START_WAIT_TIMES 100
+
+struct emac_reg_write {
+ unsigned int offset;
+ u32 val;
+};
+
+static void emac_reg_write_all(void __iomem *base,
+ const struct emac_reg_write *itr, size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; ++itr, ++i)
+ writel(itr->val, base + itr->offset);
+}
+
+static const struct emac_reg_write physical_coding_sublayer_programming_v1[] = {
+ {EMAC_SGMII_PHY_CDR_CTRL0, CDR_MAX_CNT(15)},
+ {EMAC_SGMII_PHY_POW_DWN_CTRL0, PWRDN_B},
+ {EMAC_SGMII_PHY_CMN_PWR_CTRL,
+ BIAS_EN | SYSCLK_EN | CLKBUF_L_EN | PLL_TXCLK_EN | PLL_RXCLK_EN},
+ {EMAC_SGMII_PHY_TX_PWR_CTRL, L0_TX_EN | L0_CLKBUF_EN | L0_TRAN_BIAS_EN},
+ {EMAC_SGMII_PHY_RX_PWR_CTRL,
+ L0_RX_SIGDET_EN | L0_RX_TERM_MODE(1) | L0_RX_I_EN},
+ {EMAC_SGMII_PHY_CMN_PWR_CTRL,
+ BIAS_EN | PLL_EN | SYSCLK_EN | CLKBUF_L_EN | PLL_TXCLK_EN |
+ PLL_RXCLK_EN},
+ {EMAC_SGMII_PHY_LANE_CTRL1,
+ L0_RX_EQUALIZE_ENABLE | L0_RESET_TSYNC_EN | L0_DRV_LVL(15)},
+};
+
+static const struct emac_reg_write sysclk_refclk_setting[] = {
+ {EMAC_QSERDES_COM_SYSCLK_EN_SEL, SYSCLK_SEL_CMOS},
+ {EMAC_QSERDES_COM_SYS_CLK_CTRL, SYSCLK_CM | SYSCLK_AC_COUPLE},
+};
+
+static const struct emac_reg_write pll_setting[] = {
+ {EMAC_QSERDES_COM_PLL_IP_SETI, PLL_IPSETI(1)},
+ {EMAC_QSERDES_COM_PLL_CP_SETI, PLL_CPSETI(59)},
+ {EMAC_QSERDES_COM_PLL_IP_SETP, PLL_IPSETP(10)},
+ {EMAC_QSERDES_COM_PLL_CP_SETP, PLL_CPSETP(9)},
+ {EMAC_QSERDES_COM_PLL_CRCTRL, PLL_RCTRL(15) | PLL_CCTRL(11)},
+ {EMAC_QSERDES_COM_PLL_CNTRL, OCP_EN | PLL_DIV_FFEN | PLL_DIV_ORD},
+ {EMAC_QSERDES_COM_DEC_START1, DEC_START1_MUX | DEC_START1(2)},
+ {EMAC_QSERDES_COM_DEC_START2, DEC_START2_MUX | DEC_START2},
+ {EMAC_QSERDES_COM_DIV_FRAC_START1,
+ DIV_FRAC_START_MUX | DIV_FRAC_START(85)},
+ {EMAC_QSERDES_COM_DIV_FRAC_START2,
+ DIV_FRAC_START_MUX | DIV_FRAC_START(42)},
+ {EMAC_QSERDES_COM_DIV_FRAC_START3,
+ DIV_FRAC_START3_MUX | DIV_FRAC_START3(3)},
+ {EMAC_QSERDES_COM_PLLLOCK_CMP1, PLLLOCK_CMP(43)},
+ {EMAC_QSERDES_COM_PLLLOCK_CMP2, PLLLOCK_CMP(104)},
+ {EMAC_QSERDES_COM_PLLLOCK_CMP3, PLLLOCK_CMP(0)},
+ {EMAC_QSERDES_COM_PLLLOCK_CMP_EN, PLLLOCK_CMP_EN},
+ {EMAC_QSERDES_COM_RESETSM_CNTRL, FRQ_TUNE_MODE},
+};
+
+static const struct emac_reg_write cdr_setting[] = {
+ {EMAC_QSERDES_RX_CDR_CONTROL,
+ SECONDORDERENABLE | FIRSTORDER_THRESH(3) | SECONDORDERGAIN(2)},
+ {EMAC_QSERDES_RX_CDR_CONTROL2,
+ SECONDORDERENABLE | FIRSTORDER_THRESH(3) | SECONDORDERGAIN(4)},
+};
+
+static const struct emac_reg_write tx_rx_setting[] = {
+ {EMAC_QSERDES_TX_BIST_MODE_LANENO, 0},
+ {EMAC_QSERDES_TX_TX_DRV_LVL, TX_DRV_LVL_MUX | TX_DRV_LVL(15)},
+ {EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN, EMP_EN_MUX | EMP_EN},
+ {EMAC_QSERDES_TX_TX_EMP_POST1_LVL,
+ TX_EMP_POST1_LVL_MUX | TX_EMP_POST1_LVL(1)},
+ {EMAC_QSERDES_RX_RX_EQ_GAIN12, RX_EQ_GAIN2(15) | RX_EQ_GAIN1(15)},
+ {EMAC_QSERDES_TX_LANE_MODE, LANE_MODE(8)},
+};
+
+int emac_sgmii_init_fsm9900(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ unsigned int i;
+
+ emac_reg_write_all(phy->base, physical_coding_sublayer_programming_v1,
+ ARRAY_SIZE(physical_coding_sublayer_programming_v1));
+ emac_reg_write_all(phy->base, sysclk_refclk_setting,
+ ARRAY_SIZE(sysclk_refclk_setting));
+ emac_reg_write_all(phy->base, pll_setting, ARRAY_SIZE(pll_setting));
+ emac_reg_write_all(phy->base, cdr_setting, ARRAY_SIZE(cdr_setting));
+ emac_reg_write_all(phy->base, tx_rx_setting, ARRAY_SIZE(tx_rx_setting));
+
+ /* Power up the Ser/Des engine */
+ writel(SERDES_START, phy->base + EMAC_SGMII_PHY_SERDES_START);
+
+ for (i = 0; i < SERDES_START_WAIT_TIMES; i++) {
+ if (readl(phy->base + EMAC_QSERDES_COM_RESET_SM) & READY)
+ break;
+ usleep_range(100, 200);
+ }
+
+ if (i == SERDES_START_WAIT_TIMES) {
+ netdev_err(adpt->netdev, "error: ser/des failed to start\n");
+ return -EIO;
+ }
+ /* Mask out all the SGMII Interrupt */
+ writel(0, phy->base + EMAC_SGMII_PHY_INTERRUPT_MASK);
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,210 @@
+/* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. QDF2432 EMAC SGMII Controller driver.
+ */
+
+#include <linux/iopoll.h>
+#include "emac.h"
+
+/* EMAC_SGMII register offsets */
+#define EMAC_SGMII_PHY_TX_PWR_CTRL 0x000C
+#define EMAC_SGMII_PHY_LANE_CTRL1 0x0018
+#define EMAC_SGMII_PHY_CDR_CTRL0 0x0058
+#define EMAC_SGMII_PHY_POW_DWN_CTRL0 0x0080
+#define EMAC_SGMII_PHY_RESET_CTRL 0x00a8
+#define EMAC_SGMII_PHY_INTERRUPT_MASK 0x00b4
+
+/* SGMII digital lane registers */
+#define EMAC_SGMII_LN_DRVR_CTRL0 0x000C
+#define EMAC_SGMII_LN_DRVR_TAP_EN 0x0018
+#define EMAC_SGMII_LN_TX_MARGINING 0x001C
+#define EMAC_SGMII_LN_TX_PRE 0x0020
+#define EMAC_SGMII_LN_TX_POST 0x0024
+#define EMAC_SGMII_LN_TX_BAND_MODE 0x0060
+#define EMAC_SGMII_LN_LANE_MODE 0x0064
+#define EMAC_SGMII_LN_PARALLEL_RATE 0x0078
+#define EMAC_SGMII_LN_CML_CTRL_MODE0 0x00B8
+#define EMAC_SGMII_LN_MIXER_CTRL_MODE0 0x00D0
+#define EMAC_SGMII_LN_VGA_INITVAL 0x0134
+#define EMAC_SGMII_LN_UCDR_FO_GAIN_MODE0 0x017C
+#define EMAC_SGMII_LN_UCDR_SO_GAIN_MODE0 0x0188
+#define EMAC_SGMII_LN_UCDR_SO_CONFIG 0x0194
+#define EMAC_SGMII_LN_RX_BAND 0x019C
+#define EMAC_SGMII_LN_RX_RCVR_PATH1_MODE0 0x01B8
+#define EMAC_SGMII_LN_RSM_CONFIG 0x01F0
+#define EMAC_SGMII_LN_SIGDET_ENABLES 0x0224
+#define EMAC_SGMII_LN_SIGDET_CNTRL 0x0228
+#define EMAC_SGMII_LN_SIGDET_DEGLITCH_CNTRL 0x022C
+#define EMAC_SGMII_LN_RX_EN_SIGNAL 0x02A0
+#define EMAC_SGMII_LN_RX_MISC_CNTRL0 0x02AC
+#define EMAC_SGMII_LN_DRVR_LOGIC_CLKDIV 0x02BC
+
+/* SGMII digital lane register values */
+#define UCDR_STEP_BY_TWO_MODE0 BIT(7)
+#define UCDR_xO_GAIN_MODE(x) ((x) & 0x7f)
+#define UCDR_ENABLE BIT(6)
+#define UCDR_SO_SATURATION(x) ((x) & 0x3f)
+
+#define SIGDET_LP_BYP_PS4 BIT(7)
+#define SIGDET_EN_PS0_TO_PS2 BIT(6)
+
+#define TXVAL_VALID_INIT BIT(4)
+#define KR_PCIGEN3_MODE BIT(0)
+
+#define MAIN_EN BIT(0)
+
+#define TX_MARGINING_MUX BIT(6)
+#define TX_MARGINING(x) ((x) & 0x3f)
+
+#define TX_PRE_MUX BIT(6)
+
+#define TX_POST_MUX BIT(6)
+
+#define CML_GEAR_MODE(x) (((x) & 7) << 3)
+#define CML2CMOS_IBOOST_MODE(x) ((x) & 7)
+
+#define MIXER_LOADB_MODE(x) (((x) & 0xf) << 2)
+#define MIXER_DATARATE_MODE(x) ((x) & 3)
+
+#define VGA_THRESH_DFE(x) ((x) & 0x3f)
+
+#define SIGDET_LP_BYP_PS0_TO_PS2 BIT(5)
+#define SIGDET_FLT_BYP BIT(0)
+
+#define SIGDET_LVL(x) (((x) & 0xf) << 4)
+
+#define SIGDET_DEGLITCH_CTRL(x) (((x) & 0xf) << 1)
+
+#define DRVR_LOGIC_CLK_EN BIT(4)
+#define DRVR_LOGIC_CLK_DIV(x) ((x) & 0xf)
+
+#define PARALLEL_RATE_MODE0(x) ((x) & 0x3)
+
+#define BAND_MODE0(x) ((x) & 0x3)
+
+#define LANE_MODE(x) ((x) & 0x1f)
+
+#define CDR_PD_SEL_MODE0(x) (((x) & 0x3) << 5)
+#define BYPASS_RSM_SAMP_CAL BIT(1)
+#define BYPASS_RSM_DLL_CAL BIT(0)
+
+#define L0_RX_EQUALIZE_ENABLE BIT(6)
+
+#define PWRDN_B BIT(0)
+
+#define CDR_MAX_CNT(x) ((x) & 0xff)
+
+#define SERDES_START_WAIT_TIMES 100
+
+struct emac_reg_write {
+ unsigned int offset;
+ u32 val;
+};
+
+static void emac_reg_write_all(void __iomem *base,
+ const struct emac_reg_write *itr, size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; ++itr, ++i)
+ writel(itr->val, base + itr->offset);
+}
+
+static const struct emac_reg_write sgmii_laned[] = {
+ /* CDR Settings */
+ {EMAC_SGMII_LN_UCDR_FO_GAIN_MODE0,
+ UCDR_STEP_BY_TWO_MODE0 | UCDR_xO_GAIN_MODE(10)},
+ {EMAC_SGMII_LN_UCDR_SO_GAIN_MODE0, UCDR_xO_GAIN_MODE(0)},
+ {EMAC_SGMII_LN_UCDR_SO_CONFIG, UCDR_ENABLE | UCDR_SO_SATURATION(12)},
+
+ /* TX/RX Settings */
+ {EMAC_SGMII_LN_RX_EN_SIGNAL, SIGDET_LP_BYP_PS4 | SIGDET_EN_PS0_TO_PS2},
+
+ {EMAC_SGMII_LN_DRVR_CTRL0, TXVAL_VALID_INIT | KR_PCIGEN3_MODE},
+ {EMAC_SGMII_LN_DRVR_TAP_EN, MAIN_EN},
+ {EMAC_SGMII_LN_TX_MARGINING, TX_MARGINING_MUX | TX_MARGINING(25)},
+ {EMAC_SGMII_LN_TX_PRE, TX_PRE_MUX},
+ {EMAC_SGMII_LN_TX_POST, TX_POST_MUX},
+
+ {EMAC_SGMII_LN_CML_CTRL_MODE0,
+ CML_GEAR_MODE(1) | CML2CMOS_IBOOST_MODE(1)},
+ {EMAC_SGMII_LN_MIXER_CTRL_MODE0,
+ MIXER_LOADB_MODE(12) | MIXER_DATARATE_MODE(1)},
+ {EMAC_SGMII_LN_VGA_INITVAL, VGA_THRESH_DFE(31)},
+ {EMAC_SGMII_LN_SIGDET_ENABLES,
+ SIGDET_LP_BYP_PS0_TO_PS2 | SIGDET_FLT_BYP},
+ {EMAC_SGMII_LN_SIGDET_CNTRL, SIGDET_LVL(8)},
+
+ {EMAC_SGMII_LN_SIGDET_DEGLITCH_CNTRL, SIGDET_DEGLITCH_CTRL(4)},
+ {EMAC_SGMII_LN_RX_MISC_CNTRL0, 0},
+ {EMAC_SGMII_LN_DRVR_LOGIC_CLKDIV,
+ DRVR_LOGIC_CLK_EN | DRVR_LOGIC_CLK_DIV(4)},
+
+ {EMAC_SGMII_LN_PARALLEL_RATE, PARALLEL_RATE_MODE0(1)},
+ {EMAC_SGMII_LN_TX_BAND_MODE, BAND_MODE0(2)},
+ {EMAC_SGMII_LN_RX_BAND, BAND_MODE0(3)},
+ {EMAC_SGMII_LN_LANE_MODE, LANE_MODE(26)},
+ {EMAC_SGMII_LN_RX_RCVR_PATH1_MODE0, CDR_PD_SEL_MODE0(3)},
+ {EMAC_SGMII_LN_RSM_CONFIG, BYPASS_RSM_SAMP_CAL | BYPASS_RSM_DLL_CAL},
+};
+
+static const struct emac_reg_write physical_coding_sublayer_programming[] = {
+ {EMAC_SGMII_PHY_POW_DWN_CTRL0, PWRDN_B},
+ {EMAC_SGMII_PHY_CDR_CTRL0, CDR_MAX_CNT(15)},
+ {EMAC_SGMII_PHY_TX_PWR_CTRL, 0},
+ {EMAC_SGMII_PHY_LANE_CTRL1, L0_RX_EQUALIZE_ENABLE},
+};
+
+int emac_sgmii_init_qdf2432(struct emac_adapter *adpt)
+{
+ struct emac_phy *phy = &adpt->phy;
+ void __iomem *phy_regs = phy->base;
+ void __iomem *laned = phy->digital;
+ unsigned int i;
+ u32 lnstatus;
+
+ /* PCS lane-x init */
+ emac_reg_write_all(phy->base, physical_coding_sublayer_programming,
+ ARRAY_SIZE(physical_coding_sublayer_programming));
+
+ /* SGMII lane-x init */
+ emac_reg_write_all(phy->digital, sgmii_laned, ARRAY_SIZE(sgmii_laned));
+
+ /* Power up PCS and start reset lane state machine */
+
+ writel(0, phy_regs + EMAC_SGMII_PHY_RESET_CTRL);
+ writel(1, laned + SGMII_LN_RSM_START);
+
+ /* Wait for c_ready assertion */
+ for (i = 0; i < SERDES_START_WAIT_TIMES; i++) {
+ lnstatus = readl(phy_regs + SGMII_PHY_LN_LANE_STATUS);
+ if (lnstatus & BIT(1))
+ break;
+ usleep_range(100, 200);
+ }
+
+ if (i == SERDES_START_WAIT_TIMES) {
+ netdev_err(adpt->netdev, "SGMII failed to start\n");
+ return -EIO;
+ }
+
+ /* Disable digital and SERDES loopback */
+ writel(0, phy_regs + SGMII_PHY_LN_BIST_GEN0);
+ writel(0, phy_regs + SGMII_PHY_LN_BIST_GEN2);
+ writel(0, phy_regs + SGMII_PHY_LN_CDR_CTRL1);
+
+ /* Mask out all the SGMII Interrupt */
+ writel(0, phy_regs + EMAC_SGMII_PHY_INTERRUPT_MASK);
+
+ return 0;
+}
@@ -20,448 +20,33 @@
#include "emac-mac.h"
#include "emac-sgmii.h"
-/* EMAC_QSERDES register offsets */
-#define EMAC_QSERDES_COM_SYS_CLK_CTRL 0x000000
-#define EMAC_QSERDES_COM_PLL_CNTRL 0x000014
-#define EMAC_QSERDES_COM_PLL_IP_SETI 0x000018
-#define EMAC_QSERDES_COM_PLL_CP_SETI 0x000024
-#define EMAC_QSERDES_COM_PLL_IP_SETP 0x000028
-#define EMAC_QSERDES_COM_PLL_CP_SETP 0x00002c
-#define EMAC_QSERDES_COM_SYSCLK_EN_SEL 0x000038
-#define EMAC_QSERDES_COM_RESETSM_CNTRL 0x000040
-#define EMAC_QSERDES_COM_PLLLOCK_CMP1 0x000044
-#define EMAC_QSERDES_COM_PLLLOCK_CMP2 0x000048
-#define EMAC_QSERDES_COM_PLLLOCK_CMP3 0x00004c
-#define EMAC_QSERDES_COM_PLLLOCK_CMP_EN 0x000050
-#define EMAC_QSERDES_COM_DEC_START1 0x000064
-#define EMAC_QSERDES_COM_DIV_FRAC_START1 0x000098
-#define EMAC_QSERDES_COM_DIV_FRAC_START2 0x00009c
-#define EMAC_QSERDES_COM_DIV_FRAC_START3 0x0000a0
-#define EMAC_QSERDES_COM_DEC_START2 0x0000a4
-#define EMAC_QSERDES_COM_PLL_CRCTRL 0x0000ac
-#define EMAC_QSERDES_COM_RESET_SM 0x0000bc
-#define EMAC_QSERDES_TX_BIST_MODE_LANENO 0x000100
-#define EMAC_QSERDES_TX_TX_EMP_POST1_LVL 0x000108
-#define EMAC_QSERDES_TX_TX_DRV_LVL 0x00010c
-#define EMAC_QSERDES_TX_LANE_MODE 0x000150
-#define EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN 0x000170
-#define EMAC_QSERDES_RX_CDR_CONTROL 0x000200
-#define EMAC_QSERDES_RX_CDR_CONTROL2 0x000210
-#define EMAC_QSERDES_RX_RX_EQ_GAIN12 0x000230
-
/* EMAC_SGMII register offsets */
-#define EMAC_SGMII_PHY_SERDES_START 0x000000
-#define EMAC_SGMII_PHY_CMN_PWR_CTRL 0x000004
-#define EMAC_SGMII_PHY_RX_PWR_CTRL 0x000008
-#define EMAC_SGMII_PHY_TX_PWR_CTRL 0x00000C
-#define EMAC_SGMII_PHY_LANE_CTRL1 0x000018
-#define EMAC_SGMII_PHY_AUTONEG_CFG2 0x000048
-#define EMAC_SGMII_PHY_CDR_CTRL0 0x000058
-#define EMAC_SGMII_PHY_SPEED_CFG1 0x000074
-#define EMAC_SGMII_PHY_POW_DWN_CTRL0 0x000080
-#define EMAC_SGMII_PHY_RESET_CTRL 0x0000a8
-#define EMAC_SGMII_PHY_IRQ_CMD 0x0000ac
-#define EMAC_SGMII_PHY_INTERRUPT_CLEAR 0x0000b0
-#define EMAC_SGMII_PHY_INTERRUPT_MASK 0x0000b4
-#define EMAC_SGMII_PHY_INTERRUPT_STATUS 0x0000b8
-#define EMAC_SGMII_PHY_RX_CHK_STATUS 0x0000d4
-#define EMAC_SGMII_PHY_AUTONEG0_STATUS 0x0000e0
-#define EMAC_SGMII_PHY_AUTONEG1_STATUS 0x0000e4
-
-/* EMAC_QSERDES_COM_PLL_IP_SETI */
-#define PLL_IPSETI(x) ((x) & 0x3f)
-
-/* EMAC_QSERDES_COM_PLL_CP_SETI */
-#define PLL_CPSETI(x) ((x) & 0xff)
-
-/* EMAC_QSERDES_COM_PLL_IP_SETP */
-#define PLL_IPSETP(x) ((x) & 0x3f)
-
-/* EMAC_QSERDES_COM_PLL_CP_SETP */
-#define PLL_CPSETP(x) ((x) & 0x1f)
-
-/* EMAC_QSERDES_COM_PLL_CRCTRL */
-#define PLL_RCTRL(x) (((x) & 0xf) << 4)
-#define PLL_CCTRL(x) ((x) & 0xf)
-
-/* SGMII v2 PHY registers per lane */
-#define EMAC_SGMII_PHY_LN_OFFSET 0x0400
-
-/* SGMII v2 digital lane registers */
-#define EMAC_SGMII_LN_DRVR_CTRL0 0x00C
-#define EMAC_SGMII_LN_DRVR_TAP_EN 0x018
-#define EMAC_SGMII_LN_TX_MARGINING 0x01C
-#define EMAC_SGMII_LN_TX_PRE 0x020
-#define EMAC_SGMII_LN_TX_POST 0x024
-#define EMAC_SGMII_LN_TX_BAND_MODE 0x060
-#define EMAC_SGMII_LN_LANE_MODE 0x064
-#define EMAC_SGMII_LN_PARALLEL_RATE 0x078
-#define EMAC_SGMII_LN_CML_CTRL_MODE0 0x0B8
-#define EMAC_SGMII_LN_MIXER_CTRL_MODE0 0x0D0
-#define EMAC_SGMII_LN_VGA_INITVAL 0x134
-#define EMAC_SGMII_LN_UCDR_FO_GAIN_MODE0 0x17C
-#define EMAC_SGMII_LN_UCDR_SO_GAIN_MODE0 0x188
-#define EMAC_SGMII_LN_UCDR_SO_CONFIG 0x194
-#define EMAC_SGMII_LN_RX_BAND 0x19C
-#define EMAC_SGMII_LN_RX_RCVR_PATH1_MODE0 0x1B8
-#define EMAC_SGMII_LN_RSM_CONFIG 0x1F0
-#define EMAC_SGMII_LN_SIGDET_ENABLES 0x224
-#define EMAC_SGMII_LN_SIGDET_CNTRL 0x228
-#define EMAC_SGMII_LN_SIGDET_DEGLITCH_CNTRL 0x22C
-#define EMAC_SGMII_LN_RX_EN_SIGNAL 0x2A0
-#define EMAC_SGMII_LN_RX_MISC_CNTRL0 0x2AC
-#define EMAC_SGMII_LN_DRVR_LOGIC_CLKDIV 0x2BC
-
-/* SGMII v2 digital lane register values */
-#define UCDR_STEP_BY_TWO_MODE0 BIT(7)
-#define UCDR_xO_GAIN_MODE(x) ((x) & 0x7f)
-#define UCDR_ENABLE BIT(6)
-#define UCDR_SO_SATURATION(x) ((x) & 0x3f)
-#define SIGDET_LP_BYP_PS4 BIT(7)
-#define SIGDET_EN_PS0_TO_PS2 BIT(6)
-#define EN_ACCOUPLEVCM_SW_MUX BIT(5)
-#define EN_ACCOUPLEVCM_SW BIT(4)
-#define RX_SYNC_EN BIT(3)
-#define RXTERM_HIGHZ_PS5 BIT(2)
-#define SIGDET_EN_PS3 BIT(1)
-#define EN_ACCOUPLE_VCM_PS3 BIT(0)
-#define UFS_MODE BIT(5)
-#define TXVAL_VALID_INIT BIT(4)
-#define TXVAL_VALID_MUX BIT(3)
-#define TXVAL_VALID BIT(2)
-#define USB3P1_MODE BIT(1)
-#define KR_PCIGEN3_MODE BIT(0)
-#define PRE_EN BIT(3)
-#define POST_EN BIT(2)
-#define MAIN_EN_MUX BIT(1)
-#define MAIN_EN BIT(0)
-#define TX_MARGINING_MUX BIT(6)
-#define TX_MARGINING(x) ((x) & 0x3f)
-#define TX_PRE_MUX BIT(6)
-#define TX_PRE(x) ((x) & 0x3f)
-#define TX_POST_MUX BIT(6)
-#define TX_POST(x) ((x) & 0x3f)
-#define CML_GEAR_MODE(x) (((x) & 7) << 3)
-#define CML2CMOS_IBOOST_MODE(x) ((x) & 7)
-#define MIXER_LOADB_MODE(x) (((x) & 0xf) << 2)
-#define MIXER_DATARATE_MODE(x) ((x) & 3)
-#define VGA_THRESH_DFE(x) ((x) & 0x3f)
-#define SIGDET_LP_BYP_PS0_TO_PS2 BIT(5)
-#define SIGDET_LP_BYP_MUX BIT(4)
-#define SIGDET_LP_BYP BIT(3)
-#define SIGDET_EN_MUX BIT(2)
-#define SIGDET_EN BIT(1)
-#define SIGDET_FLT_BYP BIT(0)
-#define SIGDET_LVL(x) (((x) & 0xf) << 4)
-#define SIGDET_BW_CTRL(x) ((x) & 0xf)
-#define SIGDET_DEGLITCH_CTRL(x) (((x) & 0xf) << 1)
-#define SIGDET_DEGLITCH_BYP BIT(0)
-#define INVERT_PCS_RX_CLK BIT(7)
-#define PWM_EN BIT(6)
-#define RXBIAS_SEL(x) (((x) & 0x3) << 4)
-#define EBDAC_SIGN BIT(3)
-#define EDAC_SIGN BIT(2)
-#define EN_AUXTAP1SIGN_INVERT BIT(1)
-#define EN_DAC_CHOPPING BIT(0)
-#define DRVR_LOGIC_CLK_EN BIT(4)
-#define DRVR_LOGIC_CLK_DIV(x) ((x) & 0xf)
-#define PARALLEL_RATE_MODE2(x) (((x) & 0x3) << 4)
-#define PARALLEL_RATE_MODE1(x) (((x) & 0x3) << 2)
-#define PARALLEL_RATE_MODE0(x) ((x) & 0x3)
-#define BAND_MODE2(x) (((x) & 0x3) << 4)
-#define BAND_MODE1(x) (((x) & 0x3) << 2)
-#define BAND_MODE0(x) ((x) & 0x3)
-#define LANE_SYNC_MODE BIT(5)
-#define LANE_MODE(x) ((x) & 0x1f)
-#define CDR_PD_SEL_MODE0(x) (((x) & 0x3) << 5)
-#define EN_DLL_MODE0 BIT(4)
-#define EN_IQ_DCC_MODE0 BIT(3)
-#define EN_IQCAL_MODE0 BIT(2)
-#define EN_QPATH_MODE0 BIT(1)
-#define EN_EPATH_MODE0 BIT(0)
-#define FORCE_TSYNC_ACK BIT(7)
-#define FORCE_CMN_ACK BIT(6)
-#define FORCE_CMN_READY BIT(5)
-#define EN_RCLK_DEGLITCH BIT(4)
-#define BYPASS_RSM_CDR_RESET BIT(3)
-#define BYPASS_RSM_TSYNC BIT(2)
-#define BYPASS_RSM_SAMP_CAL BIT(1)
-#define BYPASS_RSM_DLL_CAL BIT(0)
-
-/* EMAC_QSERDES_COM_SYS_CLK_CTRL */
-#define SYSCLK_CM BIT(4)
-#define SYSCLK_AC_COUPLE BIT(3)
-
-/* EMAC_QSERDES_COM_PLL_CNTRL */
-#define OCP_EN BIT(5)
-#define PLL_DIV_FFEN BIT(2)
-#define PLL_DIV_ORD BIT(1)
-
-/* EMAC_QSERDES_COM_SYSCLK_EN_SEL */
-#define SYSCLK_SEL_CMOS BIT(3)
-
-/* EMAC_QSERDES_COM_RESETSM_CNTRL */
-#define FRQ_TUNE_MODE BIT(4)
-
-/* EMAC_QSERDES_COM_PLLLOCK_CMP_EN */
-#define PLLLOCK_CMP_EN BIT(0)
-
-/* EMAC_QSERDES_COM_DEC_START1 */
-#define DEC_START1_MUX BIT(7)
-#define DEC_START1(x) ((x) & 0x7f)
-
-/* EMAC_QSERDES_COM_DIV_FRAC_START1 * EMAC_QSERDES_COM_DIV_FRAC_START2 */
-#define DIV_FRAC_START_MUX BIT(7)
-#define DIV_FRAC_START(x) ((x) & 0x7f)
-
-/* EMAC_QSERDES_COM_DIV_FRAC_START3 */
-#define DIV_FRAC_START3_MUX BIT(4)
-#define DIV_FRAC_START3(x) ((x) & 0xf)
-
-/* EMAC_QSERDES_COM_DEC_START2 */
-#define DEC_START2_MUX BIT(1)
-#define DEC_START2 BIT(0)
-
-/* EMAC_QSERDES_COM_RESET_SM */
-#define READY BIT(5)
-
-/* EMAC_QSERDES_TX_TX_EMP_POST1_LVL */
-#define TX_EMP_POST1_LVL_MUX BIT(5)
-#define TX_EMP_POST1_LVL(x) ((x) & 0x1f)
-#define TX_EMP_POST1_LVL_BMSK 0x1f
-#define TX_EMP_POST1_LVL_SHFT 0
-
-/* EMAC_QSERDES_TX_TX_DRV_LVL */
-#define TX_DRV_LVL_MUX BIT(4)
-#define TX_DRV_LVL(x) ((x) & 0xf)
-
-/* EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN */
-#define EMP_EN_MUX BIT(1)
-#define EMP_EN BIT(0)
-
-/* EMAC_QSERDES_RX_CDR_CONTROL & EMAC_QSERDES_RX_CDR_CONTROL2 */
-#define HBW_PD_EN BIT(7)
-#define SECONDORDERENABLE BIT(6)
-#define FIRSTORDER_THRESH(x) (((x) & 0x7) << 3)
-#define SECONDORDERGAIN(x) ((x) & 0x7)
-
-/* EMAC_QSERDES_RX_RX_EQ_GAIN12 */
-#define RX_EQ_GAIN2(x) (((x) & 0xf) << 4)
-#define RX_EQ_GAIN1(x) ((x) & 0xf)
-
-/* EMAC_SGMII_PHY_SERDES_START */
-#define SERDES_START BIT(0)
-
-/* EMAC_SGMII_PHY_CMN_PWR_CTRL */
-#define BIAS_EN BIT(6)
-#define PLL_EN BIT(5)
-#define SYSCLK_EN BIT(4)
-#define CLKBUF_L_EN BIT(3)
-#define PLL_TXCLK_EN BIT(1)
-#define PLL_RXCLK_EN BIT(0)
-
-/* EMAC_SGMII_PHY_RX_PWR_CTRL */
-#define L0_RX_SIGDET_EN BIT(7)
-#define L0_RX_TERM_MODE(x) (((x) & 3) << 4)
-#define L0_RX_I_EN BIT(1)
-
-/* EMAC_SGMII_PHY_TX_PWR_CTRL */
-#define L0_TX_EN BIT(5)
-#define L0_CLKBUF_EN BIT(4)
-#define L0_TRAN_BIAS_EN BIT(1)
-
-/* EMAC_SGMII_PHY_LANE_CTRL1 */
-#define L0_RX_EQUALIZE_ENABLE BIT(6)
-#define L0_RESET_TSYNC_EN BIT(4)
-#define L0_DRV_LVL(x) ((x) & 0xf)
-
-/* EMAC_SGMII_PHY_AUTONEG_CFG2 */
+#define EMAC_SGMII_PHY_AUTONEG_CFG2 0x0048
+#define EMAC_SGMII_PHY_SPEED_CFG1 0x0074
+#define EMAC_SGMII_PHY_IRQ_CMD 0x00ac
+#define EMAC_SGMII_PHY_INTERRUPT_CLEAR 0x00b0
+#define EMAC_SGMII_PHY_INTERRUPT_STATUS 0x00b8
+
#define FORCE_AN_TX_CFG BIT(5)
#define FORCE_AN_RX_CFG BIT(4)
#define AN_ENABLE BIT(0)
-/* EMAC_SGMII_PHY_SPEED_CFG1 */
#define DUPLEX_MODE BIT(4)
#define SPDMODE_1000 BIT(1)
#define SPDMODE_100 BIT(0)
#define SPDMODE_10 0
-#define SPDMODE_BMSK 3
-#define SPDMODE_SHFT 0
-
-/* EMAC_SGMII_PHY_POW_DWN_CTRL0 */
-#define PWRDN_B BIT(0)
-#define CDR_MAX_CNT(x) ((x) & 0xff)
-
-/* EMAC_QSERDES_TX_BIST_MODE_LANENO */
-#define BIST_LANE_NUMBER(x) (((x) & 3) << 5)
-#define BISTMODE(x) ((x) & 0x1f)
-
-/* EMAC_QSERDES_COM_PLLLOCK_CMPx */
-#define PLLLOCK_CMP(x) ((x) & 0xff)
-/* EMAC_SGMII_PHY_RESET_CTRL */
-#define PHY_SW_RESET BIT(0)
-
-/* EMAC_SGMII_PHY_IRQ_CMD */
#define IRQ_GLOBAL_CLEAR BIT(0)
-/* EMAC_SGMII_PHY_INTERRUPT_MASK */
#define DECODE_CODE_ERR BIT(7)
#define DECODE_DISP_ERR BIT(6)
-#define PLL_UNLOCK BIT(5)
-#define AN_ILLEGAL_TERM BIT(4)
-#define SYNC_FAIL BIT(3)
-#define AN_START BIT(2)
-#define AN_END BIT(1)
-#define AN_REQUEST BIT(0)
#define SGMII_PHY_IRQ_CLR_WAIT_TIME 10
-#define SGMII_PHY_INTERRUPT_ERR (\
- DECODE_CODE_ERR |\
- DECODE_DISP_ERR)
-
-#define SGMII_ISR_AN_MASK (\
- AN_REQUEST |\
- AN_START |\
- AN_END |\
- AN_ILLEGAL_TERM |\
- PLL_UNLOCK |\
- SYNC_FAIL)
-
-#define SGMII_ISR_MASK (\
- SGMII_PHY_INTERRUPT_ERR |\
- SGMII_ISR_AN_MASK)
-
-/* SGMII TX_CONFIG */
-#define TXCFG_LINK 0x8000
-#define TXCFG_MODE_BMSK 0x1c00
-#define TXCFG_1000_FULL 0x1800
-#define TXCFG_100_FULL 0x1400
-#define TXCFG_100_HALF 0x0400
-#define TXCFG_10_FULL 0x1000
-#define TXCFG_10_HALF 0x0000
+#define SGMII_PHY_INTERRUPT_ERR (DECODE_CODE_ERR | DECODE_DISP_ERR)
#define SERDES_START_WAIT_TIMES 100
-struct emac_reg_write {
- unsigned int offset;
- u32 val;
-};
-
-static void emac_reg_write_all(void __iomem *base,
- const struct emac_reg_write *itr, size_t size)
-{
- size_t i;
-
- for (i = 0; i < size; ++itr, ++i)
- writel(itr->val, base + itr->offset);
-}
-
-static const struct emac_reg_write physical_coding_sublayer_programming_v1[] = {
- {EMAC_SGMII_PHY_CDR_CTRL0, CDR_MAX_CNT(15)},
- {EMAC_SGMII_PHY_POW_DWN_CTRL0, PWRDN_B},
- {EMAC_SGMII_PHY_CMN_PWR_CTRL,
- BIAS_EN | SYSCLK_EN | CLKBUF_L_EN | PLL_TXCLK_EN | PLL_RXCLK_EN},
- {EMAC_SGMII_PHY_TX_PWR_CTRL, L0_TX_EN | L0_CLKBUF_EN | L0_TRAN_BIAS_EN},
- {EMAC_SGMII_PHY_RX_PWR_CTRL,
- L0_RX_SIGDET_EN | L0_RX_TERM_MODE(1) | L0_RX_I_EN},
- {EMAC_SGMII_PHY_CMN_PWR_CTRL,
- BIAS_EN | PLL_EN | SYSCLK_EN | CLKBUF_L_EN | PLL_TXCLK_EN |
- PLL_RXCLK_EN},
- {EMAC_SGMII_PHY_LANE_CTRL1,
- L0_RX_EQUALIZE_ENABLE | L0_RESET_TSYNC_EN | L0_DRV_LVL(15)},
-};
-
-static const struct emac_reg_write sysclk_refclk_setting[] = {
- {EMAC_QSERDES_COM_SYSCLK_EN_SEL, SYSCLK_SEL_CMOS},
- {EMAC_QSERDES_COM_SYS_CLK_CTRL, SYSCLK_CM | SYSCLK_AC_COUPLE},
-};
-
-static const struct emac_reg_write pll_setting[] = {
- {EMAC_QSERDES_COM_PLL_IP_SETI, PLL_IPSETI(1)},
- {EMAC_QSERDES_COM_PLL_CP_SETI, PLL_CPSETI(59)},
- {EMAC_QSERDES_COM_PLL_IP_SETP, PLL_IPSETP(10)},
- {EMAC_QSERDES_COM_PLL_CP_SETP, PLL_CPSETP(9)},
- {EMAC_QSERDES_COM_PLL_CRCTRL, PLL_RCTRL(15) | PLL_CCTRL(11)},
- {EMAC_QSERDES_COM_PLL_CNTRL, OCP_EN | PLL_DIV_FFEN | PLL_DIV_ORD},
- {EMAC_QSERDES_COM_DEC_START1, DEC_START1_MUX | DEC_START1(2)},
- {EMAC_QSERDES_COM_DEC_START2, DEC_START2_MUX | DEC_START2},
- {EMAC_QSERDES_COM_DIV_FRAC_START1,
- DIV_FRAC_START_MUX | DIV_FRAC_START(85)},
- {EMAC_QSERDES_COM_DIV_FRAC_START2,
- DIV_FRAC_START_MUX | DIV_FRAC_START(42)},
- {EMAC_QSERDES_COM_DIV_FRAC_START3,
- DIV_FRAC_START3_MUX | DIV_FRAC_START3(3)},
- {EMAC_QSERDES_COM_PLLLOCK_CMP1, PLLLOCK_CMP(43)},
- {EMAC_QSERDES_COM_PLLLOCK_CMP2, PLLLOCK_CMP(104)},
- {EMAC_QSERDES_COM_PLLLOCK_CMP3, PLLLOCK_CMP(0)},
- {EMAC_QSERDES_COM_PLLLOCK_CMP_EN, PLLLOCK_CMP_EN},
- {EMAC_QSERDES_COM_RESETSM_CNTRL, FRQ_TUNE_MODE},
-};
-
-static const struct emac_reg_write cdr_setting[] = {
- {EMAC_QSERDES_RX_CDR_CONTROL,
- SECONDORDERENABLE | FIRSTORDER_THRESH(3) | SECONDORDERGAIN(2)},
- {EMAC_QSERDES_RX_CDR_CONTROL2,
- SECONDORDERENABLE | FIRSTORDER_THRESH(3) | SECONDORDERGAIN(4)},
-};
-
-static const struct emac_reg_write tx_rx_setting[] = {
- {EMAC_QSERDES_TX_BIST_MODE_LANENO, 0},
- {EMAC_QSERDES_TX_TX_DRV_LVL, TX_DRV_LVL_MUX | TX_DRV_LVL(15)},
- {EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN, EMP_EN_MUX | EMP_EN},
- {EMAC_QSERDES_TX_TX_EMP_POST1_LVL,
- TX_EMP_POST1_LVL_MUX | TX_EMP_POST1_LVL(1)},
- {EMAC_QSERDES_RX_RX_EQ_GAIN12, RX_EQ_GAIN2(15) | RX_EQ_GAIN1(15)},
- {EMAC_QSERDES_TX_LANE_MODE, LANE_MODE(8)},
-};
-
-static const struct emac_reg_write sgmii_v2_laned[] = {
- /* CDR Settings */
- {EMAC_SGMII_LN_UCDR_FO_GAIN_MODE0,
- UCDR_STEP_BY_TWO_MODE0 | UCDR_xO_GAIN_MODE(10)},
- {EMAC_SGMII_LN_UCDR_SO_GAIN_MODE0, UCDR_xO_GAIN_MODE(0)},
- {EMAC_SGMII_LN_UCDR_SO_CONFIG, UCDR_ENABLE | UCDR_SO_SATURATION(12)},
-
- /* TX/RX Settings */
- {EMAC_SGMII_LN_RX_EN_SIGNAL, SIGDET_LP_BYP_PS4 | SIGDET_EN_PS0_TO_PS2},
-
- {EMAC_SGMII_LN_DRVR_CTRL0, TXVAL_VALID_INIT | KR_PCIGEN3_MODE},
- {EMAC_SGMII_LN_DRVR_TAP_EN, MAIN_EN},
- {EMAC_SGMII_LN_TX_MARGINING, TX_MARGINING_MUX | TX_MARGINING(25)},
- {EMAC_SGMII_LN_TX_PRE, TX_PRE_MUX},
- {EMAC_SGMII_LN_TX_POST, TX_POST_MUX},
-
- {EMAC_SGMII_LN_CML_CTRL_MODE0,
- CML_GEAR_MODE(1) | CML2CMOS_IBOOST_MODE(1)},
- {EMAC_SGMII_LN_MIXER_CTRL_MODE0,
- MIXER_LOADB_MODE(12) | MIXER_DATARATE_MODE(1)},
- {EMAC_SGMII_LN_VGA_INITVAL, VGA_THRESH_DFE(31)},
- {EMAC_SGMII_LN_SIGDET_ENABLES,
- SIGDET_LP_BYP_PS0_TO_PS2 | SIGDET_FLT_BYP},
- {EMAC_SGMII_LN_SIGDET_CNTRL, SIGDET_LVL(8)},
-
- {EMAC_SGMII_LN_SIGDET_DEGLITCH_CNTRL, SIGDET_DEGLITCH_CTRL(4)},
- {EMAC_SGMII_LN_RX_MISC_CNTRL0, 0},
- {EMAC_SGMII_LN_DRVR_LOGIC_CLKDIV,
- DRVR_LOGIC_CLK_EN | DRVR_LOGIC_CLK_DIV(4)},
-
- {EMAC_SGMII_LN_PARALLEL_RATE, PARALLEL_RATE_MODE0(1)},
- {EMAC_SGMII_LN_TX_BAND_MODE, BAND_MODE0(2)},
- {EMAC_SGMII_LN_RX_BAND, BAND_MODE0(3)},
- {EMAC_SGMII_LN_LANE_MODE, LANE_MODE(26)},
- {EMAC_SGMII_LN_RX_RCVR_PATH1_MODE0, CDR_PD_SEL_MODE0(3)},
- {EMAC_SGMII_LN_RSM_CONFIG, BYPASS_RSM_SAMP_CAL | BYPASS_RSM_DLL_CAL},
-};
-
-static const struct emac_reg_write physical_coding_sublayer_programming_v2[] = {
- {EMAC_SGMII_PHY_POW_DWN_CTRL0, PWRDN_B},
- {EMAC_SGMII_PHY_CDR_CTRL0, CDR_MAX_CNT(15)},
- {EMAC_SGMII_PHY_TX_PWR_CTRL, 0},
- {EMAC_SGMII_PHY_LANE_CTRL1, L0_RX_EQUALIZE_ENABLE},
-};
-
static int emac_sgmii_link_init(struct emac_adapter *adpt)
{
struct phy_device *phydev = adpt->phydev;
@@ -536,98 +121,6 @@ static int emac_sgmii_irq_clear(struct emac_adapter *adpt, u32 irq_bits)
return 0;
}
-int emac_sgmii_init_v1(struct emac_adapter *adpt)
-{
- struct emac_phy *phy = &adpt->phy;
- unsigned int i;
- int ret;
-
- ret = emac_sgmii_link_init(adpt);
- if (ret)
- return ret;
-
- emac_reg_write_all(phy->base, physical_coding_sublayer_programming_v1,
- ARRAY_SIZE(physical_coding_sublayer_programming_v1));
- emac_reg_write_all(phy->base, sysclk_refclk_setting,
- ARRAY_SIZE(sysclk_refclk_setting));
- emac_reg_write_all(phy->base, pll_setting, ARRAY_SIZE(pll_setting));
- emac_reg_write_all(phy->base, cdr_setting, ARRAY_SIZE(cdr_setting));
- emac_reg_write_all(phy->base, tx_rx_setting,
- ARRAY_SIZE(tx_rx_setting));
-
- /* Power up the Ser/Des engine */
- writel(SERDES_START, phy->base + EMAC_SGMII_PHY_SERDES_START);
-
- for (i = 0; i < SERDES_START_WAIT_TIMES; i++) {
- if (readl(phy->base + EMAC_QSERDES_COM_RESET_SM) & READY)
- break;
- usleep_range(100, 200);
- }
-
- if (i == SERDES_START_WAIT_TIMES) {
- netdev_err(adpt->netdev, "error: ser/des failed to start\n");
- return -EIO;
- }
- /* Mask out all the SGMII Interrupt */
- writel(0, phy->base + EMAC_SGMII_PHY_INTERRUPT_MASK);
-
- emac_sgmii_irq_clear(adpt, SGMII_PHY_INTERRUPT_ERR);
-
- return 0;
-}
-
-int emac_sgmii_init_v2(struct emac_adapter *adpt)
-{
- struct emac_phy *phy = &adpt->phy;
- void __iomem *phy_regs = phy->base;
- void __iomem *laned = phy->digital;
- unsigned int i;
- u32 lnstatus;
- int ret;
-
- ret = emac_sgmii_link_init(adpt);
- if (ret)
- return ret;
-
- /* PCS lane-x init */
- emac_reg_write_all(phy->base, physical_coding_sublayer_programming_v2,
- ARRAY_SIZE(physical_coding_sublayer_programming_v2));
-
- /* SGMII lane-x init */
- emac_reg_write_all(phy->digital,
- sgmii_v2_laned, ARRAY_SIZE(sgmii_v2_laned));
-
- /* Power up PCS and start reset lane state machine */
-
- writel(0, phy_regs + EMAC_SGMII_PHY_RESET_CTRL);
- writel(1, laned + SGMII_LN_RSM_START);
-
- /* Wait for c_ready assertion */
- for (i = 0; i < SERDES_START_WAIT_TIMES; i++) {
- lnstatus = readl(phy_regs + SGMII_PHY_LN_LANE_STATUS);
- if (lnstatus & BIT(1))
- break;
- usleep_range(100, 200);
- }
-
- if (i == SERDES_START_WAIT_TIMES) {
- netdev_err(adpt->netdev, "SGMII failed to start\n");
- return -EIO;
- }
-
- /* Disable digital and SERDES loopback */
- writel(0, phy_regs + SGMII_PHY_LN_BIST_GEN0);
- writel(0, phy_regs + SGMII_PHY_LN_BIST_GEN2);
- writel(0, phy_regs + SGMII_PHY_LN_CDR_CTRL1);
-
- /* Mask out all the SGMII Interrupt */
- writel(0, phy_regs + EMAC_SGMII_PHY_INTERRUPT_MASK);
-
- emac_sgmii_irq_clear(adpt, SGMII_PHY_INTERRUPT_ERR);
-
- return 0;
-}
-
static void emac_sgmii_reset_prepare(struct emac_adapter *adpt)
{
struct emac_phy *phy = &adpt->phy;
@@ -651,16 +144,19 @@ void emac_sgmii_reset(struct emac_adapter *adpt)
{
int ret;
- clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 19200000);
emac_sgmii_reset_prepare(adpt);
+ ret = emac_sgmii_link_init(adpt);
+ if (ret) {
+ netdev_err(adpt->netdev, "unsupported link speed\n");
+ return;
+ }
+
ret = adpt->phy.initialize(adpt);
if (ret)
netdev_err(adpt->netdev,
"could not reinitialize internal PHY (error=%i)\n",
ret);
-
- clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 125000000);
}
static int emac_sgmii_acpi_match(struct device *dev, void *data)
@@ -668,7 +164,7 @@ static int emac_sgmii_acpi_match(struct device *dev, void *data)
static const struct acpi_device_id match_table[] = {
{
.id = "QCOM8071",
- .driver_data = (kernel_ulong_t)emac_sgmii_init_v2,
+ .driver_data = (kernel_ulong_t)emac_sgmii_init_qdf2432,
},
{}
};
@@ -684,11 +180,11 @@ static int emac_sgmii_acpi_match(struct device *dev, void *data)
static const struct of_device_id emac_sgmii_dt_match[] = {
{
.compatible = "qcom,fsm9900-emac-sgmii",
- .data = emac_sgmii_init_v1,
+ .data = emac_sgmii_init_fsm9900,
},
{
.compatible = "qcom,qdf2432-emac-sgmii",
- .data = emac_sgmii_init_v2,
+ .data = emac_sgmii_init_qdf2432,
},
{}
};
@@ -760,6 +256,8 @@ int emac_sgmii_config(struct platform_device *pdev, struct emac_adapter *adpt)
if (ret)
goto error;
+ emac_sgmii_irq_clear(adpt, SGMII_PHY_INTERRUPT_ERR);
+
/* We've remapped the addresses, so we don't need the device any
* more. of_find_device_by_node() says we should release it.
*/
@@ -16,9 +16,10 @@
struct emac_adapter;
struct platform_device;
-int emac_sgmii_init_v1(struct emac_adapter *adpt);
-int emac_sgmii_init_v2(struct emac_adapter *adpt);
int emac_sgmii_config(struct platform_device *pdev, struct emac_adapter *adpt);
void emac_sgmii_reset(struct emac_adapter *adpt);
+int emac_sgmii_init_fsm9900(struct emac_adapter *adpt);
+int emac_sgmii_init_qdf2432(struct emac_adapter *adpt);
+
#endif
The internal PHY of the EMAC differs on each SOC, and the list will only continue to grow. By separating the code into individual files, we can add support for more SOCs more cleanly. Note: The internal PHY is also sometimes called the SGMII device. We also stop referring to the various PHY variations by version number, so no more "v2", "v3", etc. Instead, the devices are named after the SOC they are, which is in sync with the device tree property names. Future patches will probably rearrange more code among the files. Signed-off-by: Timur Tabi <timur@codeaurora.org> --- drivers/net/ethernet/qualcomm/emac/Makefile | 3 +- .../ethernet/qualcomm/emac/emac-sgmii-fsm9900.c | 245 ++++++++++ .../ethernet/qualcomm/emac/emac-sgmii-qdf2432.c | 210 ++++++++ drivers/net/ethernet/qualcomm/emac/emac-sgmii.c | 538 +-------------------- drivers/net/ethernet/qualcomm/emac/emac-sgmii.h | 5 +- 5 files changed, 478 insertions(+), 523 deletions(-) create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii-fsm9900.c create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii-qdf2432.c