diff mbox

[v4] net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause

Message ID 1481138451-28144-1-git-send-email-timur@codeaurora.org
State Accepted, archived
Delegated to: David Miller
Headers show

Commit Message

Timur Tabi Dec. 7, 2016, 7:20 p.m. UTC 
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case.  During
autonegotiation, the PHYs will determine whether to enable pause
frame support.

Pause frames are a feature that is supported by the MAC.  It is the MAC
that generates the frames and that processes them.  The PHY can only be
configured to allow them to pass through.

This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").

So the new process is:

1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported.  This indicates that
the PHY supports pause frames.

2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.

3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause,  If the bits are set, then it enables the corresponding
features in the MAC.  The algorithm is:

	if (phydev->pause)
		The MAC should be programmed to receive and honor
                pause frames it receives, i.e. enable receive flow control.

	if (phydev->pause != phydev->asym_pause)
		The MAC should be programmed to transmit pause
		frames when needed, i.e. enable transmit flow control.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
---

v4:
  added dp83848 driver
  removed extraneous line in phy_device

v3:
  set bits only if the PHY driver doesn't set them


 drivers/net/phy/bcm-cygnus.c |  3 +--
 drivers/net/phy/bcm7xxx.c    |  6 ++----
 drivers/net/phy/broadcom.c   | 42 ++++++++++++++----------------------------
 drivers/net/phy/dp83848.c    |  4 +---
 drivers/net/phy/icplus.c     |  6 ++----
 drivers/net/phy/intel-xway.c | 24 ++++++++----------------
 drivers/net/phy/micrel.c     | 30 ++++++++++++------------------
 drivers/net/phy/microchip.c  |  3 +--
 drivers/net/phy/national.c   |  2 +-
 drivers/net/phy/phy_device.c | 19 +++++++++++++++++++
 drivers/net/phy/smsc.c       | 18 ++++++------------
 11 files changed, 67 insertions(+), 90 deletions(-)

Comments

David Miller Dec. 9, 2016, 2:23 a.m. UTC | #1 
Florian, please review this patch.

Thanks.
David Miller Dec. 11, 2016, 4:31 a.m. UTC | #2 
From: Timur Tabi <timur@codeaurora.org>
Date: Wed,  7 Dec 2016 13:20:51 -0600

> Instead of having individual PHY drivers set the SUPPORTED_Pause and
> SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
> unless there is a hardware erratum or other special case.  During
> autonegotiation, the PHYs will determine whether to enable pause
> frame support.
> 
> Pause frames are a feature that is supported by the MAC.  It is the MAC
> that generates the frames and that processes them.  The PHY can only be
> configured to allow them to pass through.
> 
> This commit also effectively reverts the recently applied c7a61319
> ("net: phy: dp83848: Support ethernet pause frames").
> 
> So the new process is:
> 
> 1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
> and SUPPORTED_AsymPause bits in phydev->supported.  This indicates that
> the PHY supports pause frames.
> 
> 2) The MAC driver checks phydev->supported before it calls phy_start().
> If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
> sets those bits in phydev->advertising, if it wants to enable pause
> frame support.
> 
> 3) When the link state changes, the MAC driver checks phydev->pause and
> phydev->asym_pause,  If the bits are set, then it enables the corresponding
> features in the MAC.  The algorithm is:
> 
> 	if (phydev->pause)
> 		The MAC should be programmed to receive and honor
>                 pause frames it receives, i.e. enable receive flow control.
> 
> 	if (phydev->pause != phydev->asym_pause)
> 		The MAC should be programmed to transmit pause
> 		frames when needed, i.e. enable transmit flow control.
> 
> Signed-off-by: Timur Tabi <timur@codeaurora.org>

Applied.
Florian Fainelli Dec. 11, 2016, 7:45 p.m. UTC | #3 
Le 12/07/16 à 11:20, Timur Tabi a écrit :
> Instead of having individual PHY drivers set the SUPPORTED_Pause and
> SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
> unless there is a hardware erratum or other special case.  During
> autonegotiation, the PHYs will determine whether to enable pause
> frame support.
> 
> Pause frames are a feature that is supported by the MAC.  It is the MAC
> that generates the frames and that processes them.  The PHY can only be
> configured to allow them to pass through.
> 
> This commit also effectively reverts the recently applied c7a61319
> ("net: phy: dp83848: Support ethernet pause frames").
> 
> So the new process is:
> 
> 1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
> and SUPPORTED_AsymPause bits in phydev->supported.  This indicates that
> the PHY supports pause frames.
> 
> 2) The MAC driver checks phydev->supported before it calls phy_start().
> If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
> sets those bits in phydev->advertising, if it wants to enable pause
> frame support.
> 
> 3) When the link state changes, the MAC driver checks phydev->pause and
> phydev->asym_pause,  If the bits are set, then it enables the corresponding
> features in the MAC.  The algorithm is:
> 
> 	if (phydev->pause)
> 		The MAC should be programmed to receive and honor
>                 pause frames it receives, i.e. enable receive flow control.
> 
> 	if (phydev->pause != phydev->asym_pause)
> 		The MAC should be programmed to transmit pause
> 		frames when needed, i.e. enable transmit flow control.
> 
> Signed-off-by: Timur Tabi <timur@codeaurora.org>

This is already applied but:

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>

Thanks!
diff mbox

Patch

diff --git a/drivers/net/phy/bcm-cygnus.c b/drivers/net/phy/bcm-cygnus.c
index 196400c..3fe8cc5 100644
--- a/drivers/net/phy/bcm-cygnus.c
+++ b/drivers/net/phy/bcm-cygnus.c
@@ -134,8 +134,7 @@  static int bcm_cygnus_resume(struct phy_device *phydev)
 	.phy_id        = PHY_ID_BCM_CYGNUS,
 	.phy_id_mask   = 0xfffffff0,
 	.name          = "Broadcom Cygnus PHY",
-	.features      = PHY_GBIT_FEATURES |
-			SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features      = PHY_GBIT_FEATURES,
 	.config_init   = bcm_cygnus_config_init,
 	.config_aneg   = genphy_config_aneg,
 	.read_status   = genphy_read_status,
diff --git a/drivers/net/phy/bcm7xxx.c b/drivers/net/phy/bcm7xxx.c
index aae00bd..264b085 100644
--- a/drivers/net/phy/bcm7xxx.c
+++ b/drivers/net/phy/bcm7xxx.c
@@ -386,8 +386,7 @@  static int bcm7xxx_28nm_probe(struct phy_device *phydev)
 	.phy_id		= (_oui),					\
 	.phy_id_mask	= 0xfffffff0,					\
 	.name		= _name,					\
-	.features	= PHY_GBIT_FEATURES |				\
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,	\
+	.features	= PHY_GBIT_FEATURES,				\
 	.flags		= PHY_IS_INTERNAL,				\
 	.config_init	= bcm7xxx_28nm_config_init,			\
 	.config_aneg	= genphy_config_aneg,				\
@@ -406,8 +405,7 @@  static int bcm7xxx_28nm_probe(struct phy_device *phydev)
 	.phy_id         = (_oui),					\
 	.phy_id_mask    = 0xfffffff0,					\
 	.name           = _name,					\
-	.features       = PHY_BASIC_FEATURES |				\
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,	\
+	.features       = PHY_BASIC_FEATURES,				\
 	.flags          = PHY_IS_INTERNAL,				\
 	.config_init    = bcm7xxx_config_init,				\
 	.config_aneg    = genphy_config_aneg,				\
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 409b365..4223e35 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -525,8 +525,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM5411,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5411",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -537,8 +536,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM5421,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5421",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -549,8 +547,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM5461,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5461",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -561,8 +558,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM54612E,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM54612E",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= bcm54612e_config_aneg,
@@ -573,8 +569,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM54616S,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM54616S",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -585,8 +580,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM5464,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5464",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -597,8 +591,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM5481,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5481",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= bcm5481_config_aneg,
@@ -609,8 +602,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id         = PHY_ID_BCM54810,
 	.phy_id_mask    = 0xfffffff0,
 	.name           = "Broadcom BCM54810",
-	.features       = PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features       = PHY_GBIT_FEATURES,
 	.flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init    = bcm54xx_config_init,
 	.config_aneg    = bcm5481_config_aneg,
@@ -621,8 +613,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM5482,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5482",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm5482_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -633,8 +624,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM50610,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM50610",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -645,8 +635,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM50610M,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM50610M",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -657,8 +646,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM57780,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM57780",
-	.features	= PHY_GBIT_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= bcm54xx_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -669,8 +657,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCMAC131,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCMAC131",
-	.features	= PHY_BASIC_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= brcm_fet_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -681,8 +668,7 @@  static int brcm_fet_config_intr(struct phy_device *phydev)
 	.phy_id		= PHY_ID_BCM5241,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5241",
-	.features	= PHY_BASIC_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= brcm_fet_config_init,
 	.config_aneg	= genphy_config_aneg,
diff --git a/drivers/net/phy/dp83848.c b/drivers/net/phy/dp83848.c
index 320d0dc..800b39f 100644
--- a/drivers/net/phy/dp83848.c
+++ b/drivers/net/phy/dp83848.c
@@ -88,9 +88,7 @@  static int dp83848_config_intr(struct phy_device *phydev)
 		.phy_id		= _id,				\
 		.phy_id_mask	= 0xfffffff0,			\
 		.name		= _name,			\
-		.features	= (PHY_BASIC_FEATURES |		\
-				   SUPPORTED_Pause |		\
-				   SUPPORTED_Asym_Pause),	\
+		.features	= PHY_BASIC_FEATURES,		\
 		.flags		= PHY_HAS_INTERRUPT,		\
 								\
 		.soft_reset	= genphy_soft_reset,		\
diff --git a/drivers/net/phy/icplus.c b/drivers/net/phy/icplus.c
index e5f251b..22b51f0 100644
--- a/drivers/net/phy/icplus.c
+++ b/drivers/net/phy/icplus.c
@@ -225,8 +225,7 @@  static int ip101a_g_ack_interrupt(struct phy_device *phydev)
 	.phy_id		= 0x02430d90,
 	.name		= "ICPlus IP1001",
 	.phy_id_mask	= 0x0ffffff0,
-	.features	= PHY_GBIT_FEATURES | SUPPORTED_Pause |
-			  SUPPORTED_Asym_Pause,
+	.features	= PHY_GBIT_FEATURES,
 	.config_init	= &ip1001_config_init,
 	.config_aneg	= &genphy_config_aneg,
 	.read_status	= &genphy_read_status,
@@ -236,8 +235,7 @@  static int ip101a_g_ack_interrupt(struct phy_device *phydev)
 	.phy_id		= 0x02430c54,
 	.name		= "ICPlus IP101A/G",
 	.phy_id_mask	= 0x0ffffff0,
-	.features	= PHY_BASIC_FEATURES | SUPPORTED_Pause |
-			  SUPPORTED_Asym_Pause,
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_INTERRUPT,
 	.ack_interrupt	= ip101a_g_ack_interrupt,
 	.config_init	= &ip101a_g_config_init,
diff --git a/drivers/net/phy/intel-xway.c b/drivers/net/phy/intel-xway.c
index c300ab5..b1fd7bb 100644
--- a/drivers/net/phy/intel-xway.c
+++ b/drivers/net/phy/intel-xway.c
@@ -239,8 +239,7 @@  static int xway_gphy_config_intr(struct phy_device *phydev)
 		.phy_id		= PHY_ID_PHY11G_1_3,
 		.phy_id_mask	= 0xffffffff,
 		.name		= "Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3",
-		.features	= (PHY_GBIT_FEATURES | SUPPORTED_Pause |
-				   SUPPORTED_Asym_Pause),
+		.features	= PHY_GBIT_FEATURES,
 		.flags		= PHY_HAS_INTERRUPT,
 		.config_init	= xway_gphy_config_init,
 		.config_aneg	= xway_gphy14_config_aneg,
@@ -254,8 +253,7 @@  static int xway_gphy_config_intr(struct phy_device *phydev)
 		.phy_id		= PHY_ID_PHY22F_1_3,
 		.phy_id_mask	= 0xffffffff,
 		.name		= "Intel XWAY PHY22F (PEF 7061) v1.3",
-		.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
-				   SUPPORTED_Asym_Pause),
+		.features	= PHY_BASIC_FEATURES,
 		.flags		= PHY_HAS_INTERRUPT,
 		.config_init	= xway_gphy_config_init,
 		.config_aneg	= xway_gphy14_config_aneg,
@@ -269,8 +267,7 @@  static int xway_gphy_config_intr(struct phy_device *phydev)
 		.phy_id		= PHY_ID_PHY11G_1_4,
 		.phy_id_mask	= 0xffffffff,
 		.name		= "Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.4",
-		.features	= (PHY_GBIT_FEATURES | SUPPORTED_Pause |
-				   SUPPORTED_Asym_Pause),
+		.features	= PHY_GBIT_FEATURES,
 		.flags		= PHY_HAS_INTERRUPT,
 		.config_init	= xway_gphy_config_init,
 		.config_aneg	= xway_gphy14_config_aneg,
@@ -284,8 +281,7 @@  static int xway_gphy_config_intr(struct phy_device *phydev)
 		.phy_id		= PHY_ID_PHY22F_1_4,
 		.phy_id_mask	= 0xffffffff,
 		.name		= "Intel XWAY PHY22F (PEF 7061) v1.4",
-		.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
-				   SUPPORTED_Asym_Pause),
+		.features	= PHY_BASIC_FEATURES,
 		.flags		= PHY_HAS_INTERRUPT,
 		.config_init	= xway_gphy_config_init,
 		.config_aneg	= xway_gphy14_config_aneg,
@@ -299,8 +295,7 @@  static int xway_gphy_config_intr(struct phy_device *phydev)
 		.phy_id		= PHY_ID_PHY11G_1_5,
 		.phy_id_mask	= 0xffffffff,
 		.name		= "Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6",
-		.features	= (PHY_GBIT_FEATURES | SUPPORTED_Pause |
-				   SUPPORTED_Asym_Pause),
+		.features	= PHY_GBIT_FEATURES,
 		.flags		= PHY_HAS_INTERRUPT,
 		.config_init	= xway_gphy_config_init,
 		.config_aneg	= genphy_config_aneg,
@@ -314,8 +309,7 @@  static int xway_gphy_config_intr(struct phy_device *phydev)
 		.phy_id		= PHY_ID_PHY22F_1_5,
 		.phy_id_mask	= 0xffffffff,
 		.name		= "Intel XWAY PHY22F (PEF 7061) v1.5 / v1.6",
-		.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
-				   SUPPORTED_Asym_Pause),
+		.features	= PHY_BASIC_FEATURES,
 		.flags		= PHY_HAS_INTERRUPT,
 		.config_init	= xway_gphy_config_init,
 		.config_aneg	= genphy_config_aneg,
@@ -329,8 +323,7 @@  static int xway_gphy_config_intr(struct phy_device *phydev)
 		.phy_id		= PHY_ID_PHY11G_VR9,
 		.phy_id_mask	= 0xffffffff,
 		.name		= "Intel XWAY PHY11G (xRX integrated)",
-		.features	= (PHY_GBIT_FEATURES | SUPPORTED_Pause |
-				   SUPPORTED_Asym_Pause),
+		.features	= PHY_GBIT_FEATURES,
 		.flags		= PHY_HAS_INTERRUPT,
 		.config_init	= xway_gphy_config_init,
 		.config_aneg	= genphy_config_aneg,
@@ -344,8 +337,7 @@  static int xway_gphy_config_intr(struct phy_device *phydev)
 		.phy_id		= PHY_ID_PHY22F_VR9,
 		.phy_id_mask	= 0xffffffff,
 		.name		= "Intel XWAY PHY22F (xRX integrated)",
-		.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
-				   SUPPORTED_Asym_Pause),
+		.features	= PHY_BASIC_FEATURES,
 		.flags		= PHY_HAS_INTERRUPT,
 		.config_init	= xway_gphy_config_init,
 		.config_aneg	= genphy_config_aneg,
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index ea92d52..9a77289 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -790,7 +790,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KS8737,
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	.name		= "Micrel KS8737",
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ks8737_type,
 	.config_init	= kszphy_config_init,
@@ -807,8 +807,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ8021,
 	.phy_id_mask	= 0x00ffffff,
 	.name		= "Micrel KSZ8021 or KSZ8031",
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
-			   SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ksz8021_type,
 	.probe		= kszphy_probe,
@@ -826,8 +825,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ8031,
 	.phy_id_mask	= 0x00ffffff,
 	.name		= "Micrel KSZ8031",
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
-			   SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ksz8021_type,
 	.probe		= kszphy_probe,
@@ -845,8 +843,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ8041,
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	.name		= "Micrel KSZ8041",
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
-				| SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ksz8041_type,
 	.probe		= kszphy_probe,
@@ -864,8 +861,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ8041RNLI,
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	.name		= "Micrel KSZ8041RNLI",
-	.features	= PHY_BASIC_FEATURES |
-			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ksz8041_type,
 	.probe		= kszphy_probe,
@@ -883,8 +879,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ8051,
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	.name		= "Micrel KSZ8051",
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
-				| SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ksz8051_type,
 	.probe		= kszphy_probe,
@@ -902,7 +897,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ8001,
 	.name		= "Micrel KSZ8001 or KS8721",
 	.phy_id_mask	= 0x00fffffc,
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ksz8041_type,
 	.probe		= kszphy_probe,
@@ -920,7 +915,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ8081,
 	.name		= "Micrel KSZ8081 or KSZ8091",
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ksz8081_type,
 	.probe		= kszphy_probe,
@@ -938,7 +933,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ8061,
 	.name		= "Micrel KSZ8061",
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= kszphy_config_init,
 	.config_aneg	= genphy_config_aneg,
@@ -954,7 +949,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ9021,
 	.phy_id_mask	= 0x000ffffe,
 	.name		= "Micrel KSZ9021 Gigabit PHY",
-	.features	= (PHY_GBIT_FEATURES | SUPPORTED_Pause),
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ksz9021_type,
 	.config_init	= ksz9021_config_init,
@@ -973,7 +968,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ9031,
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	.name		= "Micrel KSZ9031 Gigabit PHY",
-	.features	= (PHY_GBIT_FEATURES | SUPPORTED_Pause),
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.driver_data	= &ksz9021_type,
 	.config_init	= ksz9031_config_init,
@@ -990,7 +985,6 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ8873MLL,
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	.name		= "Micrel KSZ8873MLL Switch",
-	.features	= (SUPPORTED_Pause | SUPPORTED_Asym_Pause),
 	.flags		= PHY_HAS_MAGICANEG,
 	.config_init	= kszphy_config_init,
 	.config_aneg	= ksz8873mll_config_aneg,
@@ -1004,7 +998,7 @@  static int kszphy_probe(struct phy_device *phydev)
 	.phy_id		= PHY_ID_KSZ886X,
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	.name		= "Micrel KSZ886X Switch",
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 	.config_init	= kszphy_config_init,
 	.config_aneg	= genphy_config_aneg,
diff --git a/drivers/net/phy/microchip.c b/drivers/net/phy/microchip.c
index 12825a5..324fbf6 100644
--- a/drivers/net/phy/microchip.c
+++ b/drivers/net/phy/microchip.c
@@ -146,8 +146,7 @@  static int lan88xx_config_aneg(struct phy_device *phydev)
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Microchip LAN88xx",
 
-	.features	= (PHY_GBIT_FEATURES |
-			   SUPPORTED_Pause | SUPPORTED_Asym_Pause),
+	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG,
 
 	.probe		= lan88xx_probe,
diff --git a/drivers/net/phy/national.c b/drivers/net/phy/national.c
index 2a1b490..2addf1d 100644
--- a/drivers/net/phy/national.c
+++ b/drivers/net/phy/national.c
@@ -133,7 +133,7 @@  static int ns_config_init(struct phy_device *phydev)
 	.phy_id = DP83865_PHY_ID,
 	.phy_id_mask = 0xfffffff0,
 	.name = "NatSemi DP83865",
-	.features = PHY_GBIT_FEATURES | SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.features = PHY_GBIT_FEATURES,
 	.flags = PHY_HAS_INTERRUPT,
 	.config_init = ns_config_init,
 	.config_aneg = genphy_config_aneg,
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index aeaf1bc..416640d 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1662,6 +1662,25 @@  static int phy_probe(struct device *dev)
 	 */
 	of_set_phy_eee_broken(phydev);
 
+	/* The Pause Frame bits indicate that the PHY can support passing
+	 * pause frames. During autonegotiation, the PHYs will determine if
+	 * they should allow pause frames to pass.  The MAC driver should then
+	 * use that result to determine whether to enable flow control via
+	 * pause frames.
+	 *
+	 * Normally, PHY drivers should not set the Pause bits, and instead
+	 * allow phylib to do that.  However, there may be some situations
+	 * (e.g. hardware erratum) where the driver wants to set only one
+	 * of these bits.
+	 */
+	if (phydrv->features & (SUPPORTED_Pause | SUPPORTED_Asym_Pause)) {
+		phydev->supported &= ~(SUPPORTED_Pause | SUPPORTED_Asym_Pause);
+		phydev->supported |= phydrv->features &
+				     (SUPPORTED_Pause | SUPPORTED_Asym_Pause);
+	} else {
+		phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
+	}
+
 	/* Set the state to READY by default */
 	phydev->state = PHY_READY;
 
diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c
index b62c4aa..fb32eaf 100644
--- a/drivers/net/phy/smsc.c
+++ b/drivers/net/phy/smsc.c
@@ -168,8 +168,7 @@  static int smsc_phy_probe(struct phy_device *phydev)
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "SMSC LAN83C185",
 
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
-				| SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG,
 
 	.probe		= smsc_phy_probe,
@@ -191,8 +190,7 @@  static int smsc_phy_probe(struct phy_device *phydev)
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "SMSC LAN8187",
 
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
-				| SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG,
 
 	.probe		= smsc_phy_probe,
@@ -214,8 +212,7 @@  static int smsc_phy_probe(struct phy_device *phydev)
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "SMSC LAN8700",
 
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
-				| SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG,
 
 	.probe		= smsc_phy_probe,
@@ -237,8 +234,7 @@  static int smsc_phy_probe(struct phy_device *phydev)
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "SMSC LAN911x Internal PHY",
 
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
-				| SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG,
 
 	.probe		= smsc_phy_probe,
@@ -259,8 +255,7 @@  static int smsc_phy_probe(struct phy_device *phydev)
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "SMSC LAN8710/LAN8720",
 
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
-				| SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG,
 
 	.probe		= smsc_phy_probe,
@@ -282,8 +277,7 @@  static int smsc_phy_probe(struct phy_device *phydev)
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "SMSC LAN8740",
 
-	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
-				| SUPPORTED_Asym_Pause),
+	.features	= PHY_BASIC_FEATURES,
 	.flags		= PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG,
 
 	.probe		= smsc_phy_probe,