diff mbox

[U-Boot,v6] mx6sx: Add initial support for Samtec VIN|ING 2000 board

Message ID 1480432420.2233.4.camel@googlemail.com
State Awaiting Upstream
Delegated to: Stefano Babic
Headers show

Commit Message

Christoph Fritz Nov. 29, 2016, 3:13 p.m. UTC 
This patch adds initial support for Samtec VIN|ING 2000 board.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
---
Changes since v1:
 - add more comments (enet phy init)
 - fix layout style e.g. multi-line-comments
 - use pinmux macros
 - use helper funcs clrsetbits_le32() and wait_for_bit()
 - make some functions static
 - drop board_ehci_hcd_init() and board_phy_config()
 - simplify environment
Changes since v2:
 - adapt error handling in board_eth_init() and read_adc()
 - purge unused macros
 - use config_distro_bootcmd as environment
 - fix CONFIG_PWM_IMX undef handling
Changes since v3:
 - fix comment spelling
 - use u32
 - rearrange if condition
Changes since v4:
 - use parent error codes
 - rename config string to TARGET_SAMTEC_VINING_2000
Changes since v5:
 - simplify board_eth_init() error message

 arch/arm/cpu/armv7/mx6/Kconfig         |   7 +
 board/samtec/vining_2000/Kconfig       |  12 +
 board/samtec/vining_2000/MAINTAINERS   |   6 +
 board/samtec/vining_2000/Makefile      |   6 +
 board/samtec/vining_2000/imximage.cfg  | 132 +++++++++
 board/samtec/vining_2000/vining_2000.c | 517 +++++++++++++++++++++++++++++++++
 configs/vining_2000_defconfig          |  31 ++
 include/configs/vining_2000.h          | 123 ++++++++
 8 files changed, 834 insertions(+)
 create mode 100644 board/samtec/vining_2000/Kconfig
 create mode 100644 board/samtec/vining_2000/MAINTAINERS
 create mode 100644 board/samtec/vining_2000/Makefile
 create mode 100644 board/samtec/vining_2000/imximage.cfg
 create mode 100644 board/samtec/vining_2000/vining_2000.c
 create mode 100644 configs/vining_2000_defconfig
 create mode 100644 include/configs/vining_2000.h

Comments

Stefano Babic Nov. 29, 2016, 3:21 p.m. UTC | #1 
On 29/11/2016 16:13, Christoph Fritz wrote:
> This patch adds initial support for Samtec VIN|ING 2000 board.
> 
> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
> ---
> Changes since v1:
>  - add more comments (enet phy init)
>  - fix layout style e.g. multi-line-comments
>  - use pinmux macros
>  - use helper funcs clrsetbits_le32() and wait_for_bit()
>  - make some functions static
>  - drop board_ehci_hcd_init() and board_phy_config()
>  - simplify environment
> Changes since v2:
>  - adapt error handling in board_eth_init() and read_adc()
>  - purge unused macros
>  - use config_distro_bootcmd as environment
>  - fix CONFIG_PWM_IMX undef handling
> Changes since v3:
>  - fix comment spelling
>  - use u32
>  - rearrange if condition
> Changes since v4:
>  - use parent error codes
>  - rename config string to TARGET_SAMTEC_VINING_2000
> Changes since v5:
>  - simplify board_eth_init() error message
> 
>  arch/arm/cpu/armv7/mx6/Kconfig         |   7 +
>  board/samtec/vining_2000/Kconfig       |  12 +
>  board/samtec/vining_2000/MAINTAINERS   |   6 +
>  board/samtec/vining_2000/Makefile      |   6 +
>  board/samtec/vining_2000/imximage.cfg  | 132 +++++++++
>  board/samtec/vining_2000/vining_2000.c | 517 +++++++++++++++++++++++++++++++++
>  configs/vining_2000_defconfig          |  31 ++
>  include/configs/vining_2000.h          | 123 ++++++++
>  8 files changed, 834 insertions(+)
>  create mode 100644 board/samtec/vining_2000/Kconfig
>  create mode 100644 board/samtec/vining_2000/MAINTAINERS
>  create mode 100644 board/samtec/vining_2000/Makefile
>  create mode 100644 board/samtec/vining_2000/imximage.cfg
>  create mode 100644 board/samtec/vining_2000/vining_2000.c
>  create mode 100644 configs/vining_2000_defconfig
>  create mode 100644 include/configs/vining_2000.h
> 
> diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
> index 762a581..057b8cd 100644
> --- a/arch/arm/cpu/armv7/mx6/Kconfig
> +++ b/arch/arm/cpu/armv7/mx6/Kconfig
> @@ -192,6 +192,12 @@ config TARGET_UDOO
>  	bool "udoo"
>  	select SUPPORT_SPL
>  
> +config TARGET_SAMTEC_VINING_2000
> +	bool "samtec VIN|ING 2000"
> +	select MX6SX
> +	select DM
> +	select DM_THERMAL
> +
>  config TARGET_WANDBOARD
>  	bool "wandboard"
>  	select SUPPORT_SPL
> @@ -247,6 +253,7 @@ source "board/freescale/mx6ullevk/Kconfig"
>  source "board/phytec/pcm058/Kconfig"
>  source "board/gateworks/gw_ventana/Kconfig"
>  source "board/kosagi/novena/Kconfig"
> +source "board/samtec/vining_2000/Kconfig"
>  source "board/seco/Kconfig"
>  source "board/solidrun/mx6cuboxi/Kconfig"
>  source "board/technexion/pico-imx6ul/Kconfig"
> diff --git a/board/samtec/vining_2000/Kconfig b/board/samtec/vining_2000/Kconfig
> new file mode 100644
> index 0000000..3447c27
> --- /dev/null
> +++ b/board/samtec/vining_2000/Kconfig
> @@ -0,0 +1,12 @@
> +if TARGET_SAMTEC_VINING_2000
> +
> +config SYS_BOARD
> +	default "vining_2000"
> +
> +config SYS_VENDOR
> +	default "samtec"
> +
> +config SYS_CONFIG_NAME
> +	default "vining_2000"
> +
> +endif
> diff --git a/board/samtec/vining_2000/MAINTAINERS b/board/samtec/vining_2000/MAINTAINERS
> new file mode 100644
> index 0000000..027e527
> --- /dev/null
> +++ b/board/samtec/vining_2000/MAINTAINERS
> @@ -0,0 +1,6 @@
> +VINING_2000 BOARD
> +M:	Ingo Schroeck <open-source@samtec.de>
> +S:	Maintained
> +F:	board/samtec/vining_2000/
> +F:	include/configs/vining_2000.h
> +F:	configs/vining_2000_defconfig
> diff --git a/board/samtec/vining_2000/Makefile b/board/samtec/vining_2000/Makefile
> new file mode 100644
> index 0000000..1b32f66
> --- /dev/null
> +++ b/board/samtec/vining_2000/Makefile
> @@ -0,0 +1,6 @@
> +# (C) Copyright 2016 samtec automotive software & electronics gmbh
> +#
> +# SPDX-License-Identifier:	GPL-2.0+
> +#
> +
> +obj-y  := vining_2000.o
> diff --git a/board/samtec/vining_2000/imximage.cfg b/board/samtec/vining_2000/imximage.cfg
> new file mode 100644
> index 0000000..4133dda
> --- /dev/null
> +++ b/board/samtec/vining_2000/imximage.cfg
> @@ -0,0 +1,132 @@
> +/*
> + * Copyright (C) 2016 samtec automotive software & electronics gmbh
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#define __ASSEMBLY__
> +#include <config.h>
> +
> +/* image version */
> +
> +IMAGE_VERSION 2
> +
> +/*
> + * Boot Device : one of
> + * spi/sd/nand/onenand, qspi/nor
> + */
> +
> +BOOT_FROM	sd
> +
> +/*
> + * Device Configuration Data (DCD)
> + *
> + * Each entry must have the format:
> + * Addr-type           Address        Value
> + *
> + * where:
> + *	Addr-type register length (1,2 or 4 bytes)
> + *	Address	  absolute address of the register
> + *	value	  value to be stored in the register
> + */
> +
> +/* Enable all clocks */
> +DATA 4 0x020c4068 0xffffffff
> +DATA 4 0x020c406c 0xffffffff
> +DATA 4 0x020c4070 0xffffffff
> +DATA 4 0x020c4074 0xffffffff
> +DATA 4 0x020c4078 0xffffffff
> +DATA 4 0x020c407c 0xffffffff
> +DATA 4 0x020c4080 0xffffffff
> +DATA 4 0x020c4084 0xffffffff
> +
> +/* IOMUX - DDR IO Type */
> +DATA 4 0x020e0618 0x000c0000
> +DATA 4 0x020e05fc 0x00000000
> +
> +/* Clock */
> +DATA 4 0x020e032c 0x00000030
> +
> +/* Address */
> +DATA 4 0x020e0300 0x00000028
> +DATA 4 0x020e02fc 0x00000028
> +DATA 4 0x020e05f4 0x00000028
> +
> +/* Control */
> +DATA 4 0x020e0340 0x00000028
> +
> +DATA 4 0x020e0320 0x00000000
> +DATA 4 0x020e0310 0x00000028
> +DATA 4 0x020e0314 0x00000028
> +DATA 4 0x020e0614 0x00000028
> +
> +/* Data Strobe */
> +DATA 4 0x020e05f8 0x00020000
> +DATA 4 0x020e0330 0x00000028
> +DATA 4 0x020e0334 0x00000028
> +DATA 4 0x020e0338 0x00000028
> +DATA 4 0x020e033c 0x00000028
> +
> +/* Data */
> +DATA 4 0x020e0608 0x00020000
> +DATA 4 0x020e060c 0x00000028
> +DATA 4 0x020e0610 0x00000028
> +DATA 4 0x020e061c 0x00000028
> +DATA 4 0x020e0620 0x00000028
> +DATA 4 0x020e02ec 0x00000028
> +DATA 4 0x020e02f0 0x00000028
> +DATA 4 0x020e02f4 0x00000028
> +DATA 4 0x020e02f8 0x00000028
> +
> +/* Calibrations - ZQ */
> +DATA 4 0x021b0800 0xa1390003
> +
> +/* Write leveling */
> +DATA 4 0x021b080c 0x00290025
> +DATA 4 0x021b0810 0x00210022
> +
> +/* DQS Read Gate */
> +DATA 4 0x021b083c 0x4142013a
> +DATA 4 0x021b0840 0x012e0123
> +
> +/* Read/Write Delay */
> +DATA 4 0x021b0848 0x43474949
> +DATA 4 0x021b0850 0x38383c38
> +
> +/* Read data bit delay */
> +DATA 4 0x021b081c 0x33333333
> +DATA 4 0x021b0820 0x33333333
> +DATA 4 0x021b0824 0x33333333
> +DATA 4 0x021b0828 0x33333333
> +
> +/* Complete calibration by forced measurement */
> +DATA 4 0x021b08b8 0x00000800
> +
> +/* MMDC init - DDR3, 64-bit mode, only MMDC0 is initiated */
> +DATA 4 0x021b0004 0x0002002d
> +DATA 4 0x021b0008 0x00333040
> +DATA 4 0x021b000c 0x676b52f2
> +DATA 4 0x021b0010 0x926e8b63
> +DATA 4 0x021b0014 0x01ff00db
> +DATA 4 0x021b0018 0x00011740
> +DATA 4 0x021b001c 0x00008000
> +DATA 4 0x021b002c 0x000026d2
> +DATA 4 0x021b0030 0x006b1023
> +DATA 4 0x021b0040 0x0000005f
> +DATA 4 0x021b0000 0x84190000
> +
> +/* Initialize MT41K256M16HA-125 - MR2 */
> +DATA 4 0x021b001c 0x02008032
> +/* MR3 */
> +DATA 4 0x021b001c 0x00008033
> +/* MR1 */
> +DATA 4 0x021b001c 0x00048031
> +/* MR0 */
> +DATA 4 0x021b001c 0x15108030
> +/* DDR device ZQ calibration */
> +DATA 4 0x021b001c 0x04008040
> +
> +/* Final DDR setup, before operation start */
> +DATA 4 0x021b0020 0x00007800
> +DATA 4 0x021b0818 0x00022227
> +DATA 4 0x021b001c 0x00000000
> diff --git a/board/samtec/vining_2000/vining_2000.c b/board/samtec/vining_2000/vining_2000.c
> new file mode 100644
> index 0000000..c92f37c
> --- /dev/null
> +++ b/board/samtec/vining_2000/vining_2000.c
> @@ -0,0 +1,517 @@
> +/*
> + * Copyright (C) 2016 samtec automotive software & electronics gmbh
> + *
> + * Author: Christoph Fritz <chf.fritz@googlemail.com>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#include <asm/arch/clock.h>
> +#include <asm/arch/crm_regs.h>
> +#include <asm/arch/iomux.h>
> +#include <asm/arch/imx-regs.h>
> +#include <asm/arch/mx6-pins.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/gpio.h>
> +#include <asm/imx-common/iomux-v3.h>
> +#include <asm/io.h>
> +#include <asm/imx-common/mxc_i2c.h>
> +#include <linux/sizes.h>
> +#include <common.h>
> +#include <fsl_esdhc.h>
> +#include <mmc.h>
> +#include <i2c.h>
> +#include <miiphy.h>
> +#include <netdev.h>
> +#include <power/pmic.h>
> +#include <power/pfuze100_pmic.h>
> +#include <usb.h>
> +#include <usb/ehci-ci.h>
> +#include <pwm.h>
> +#include <wait_bit.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#define UART_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
> +	PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |	\
> +	PAD_CTL_SRE_FAST)
> +
> +#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PKE |	\
> +	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm |		\
> +	PAD_CTL_SRE_FAST)
> +
> +#define ENET_CLK_PAD_CTRL  PAD_CTL_DSE_34ohm
> +
> +#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE |			\
> +	PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_HIGH |		\
> +	PAD_CTL_SRE_FAST)
> +
> +#define I2C_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
> +	PAD_CTL_PKE | PAD_CTL_ODE | PAD_CTL_SPEED_MED |		\
> +	PAD_CTL_DSE_40ohm)
> +
> +#define USDHC_CLK_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_SPEED_MED |	\
> +	PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST)
> +
> +#define USDHC_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP |	\
> +	PAD_CTL_PKE |  PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm |	\
> +	PAD_CTL_SRE_FAST)
> +
> +#define GPIO_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
> +	PAD_CTL_PKE)
> +
> +int dram_init(void)
> +{
> +	gd->ram_size = imx_ddr_size();
> +
> +	return 0;
> +}
> +
> +static iomux_v3_cfg_t const uart1_pads[] = {
> +	MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
> +	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
> +};
> +
> +static iomux_v3_cfg_t const usdhc2_pads[] = {
> +	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
> +	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_LCD1_VSYNC__GPIO3_IO_28 | MUX_PAD_CTRL(GPIO_PAD_CTRL),
> +};
> +
> +static iomux_v3_cfg_t const usdhc4_pads[] = {
> +	MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
> +	MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +	MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +};
> +
> +static iomux_v3_cfg_t const fec1_pads[] = {
> +	MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
> +	MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
> +	MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
> +	MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
> +	MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> +	MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> +	MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
> +	MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
> +	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL) |
> +		MUX_MODE_SION,
> +	/* LAN8720 PHY Reset */
> +	MX6_PAD_RGMII1_TD3__GPIO5_IO_9 | MUX_PAD_CTRL(NO_PAD_CTRL),
> +};
> +
> +static iomux_v3_cfg_t const pwm_led_pads[] = {
> +	MX6_PAD_RGMII2_RD2__PWM2_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* green */
> +	MX6_PAD_RGMII2_TD2__PWM6_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* red */
> +	MX6_PAD_RGMII2_RD3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* blue */
> +};
> +
> +static void setup_iomux_uart(void)
> +{
> +	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
> +}
> +
> +#define PHY_RESET IMX_GPIO_NR(5, 9)
> +
> +int board_eth_init(bd_t *bis)
> +{
> +	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
> +	int ret;
> +	unsigned char eth1addr[6];
> +
> +	/* just to get secound mac address */
> +	imx_get_mac_from_fuse(1, eth1addr);
> +	if (!getenv("eth1addr") && is_valid_ethaddr(eth1addr))
> +		eth_setenv_enetaddr("eth1addr", eth1addr);
> +
> +	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
> +
> +	/*
> +	 * Generate phy reference clock via pin IOMUX ENET_REF_CLK1/2 by erasing
> +	 * ENET1/2_TX_CLK_DIR gpr1[14:13], so that reference clock is driven by
> +	 * ref_enetpll0/1 and enable ENET1/2_TX_CLK output driver.
> +	 */
> +	clrsetbits_le32(&iomuxc_regs->gpr[1],
> +			IOMUX_GPR1_FEC1_CLOCK_MUX2_SEL_MASK |
> +			IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK,
> +			IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK |
> +			IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
> +
> +	ret = enable_fec_anatop_clock(0, ENET_50MHZ);
> +	if (ret)
> +		goto eth_fail;
> +
> +	/* reset phy */
> +	gpio_direction_output(PHY_RESET, 0);
> +	mdelay(16);
> +	gpio_set_value(PHY_RESET, 1);
> +	mdelay(1);
> +
> +	ret = fecmxc_initialize_multi(bis, 0, CONFIG_FEC_MXC_PHYADDR,
> +					IMX_FEC_BASE);
> +	if (ret)
> +		goto eth_fail;
> +
> +	return ret;
> +
> +eth_fail:
> +	printf("FEC MXC: %s:failed (%i)\n", __func__, ret);
> +	gpio_set_value(PHY_RESET, 0);
> +	return ret;
> +}
> +
> +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
> +/* I2C1 for PMIC */
> +static struct i2c_pads_info i2c_pad_info1 = {
> +	.scl = {
> +		.i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
> +		.gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
> +		.gp = IMX_GPIO_NR(1, 0),
> +	},
> +	.sda = {
> +		.i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
> +		.gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
> +		.gp = IMX_GPIO_NR(1, 1),
> +	},
> +};
> +
> +static struct pmic *pfuze_init(unsigned char i2cbus)
> +{
> +	struct pmic *p;
> +	int ret;
> +	u32 reg;
> +
> +	ret = power_pfuze100_init(i2cbus);
> +	if (ret)
> +		return NULL;
> +
> +	p = pmic_get("PFUZE100");
> +	ret = pmic_probe(p);
> +	if (ret)
> +		return NULL;
> +
> +	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
> +	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
> +
> +	/* Set SW1AB stanby volage to 0.975V */
> +	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
> +	reg &= ~SW1x_STBY_MASK;
> +	reg |= SW1x_0_975V;
> +	pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
> +
> +	/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
> +	pmic_reg_read(p, PFUZE100_SW1ABCONF, &reg);
> +	reg &= ~SW1xCONF_DVSSPEED_MASK;
> +	reg |= SW1xCONF_DVSSPEED_4US;
> +	pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
> +
> +	/* Set SW1C standby voltage to 0.975V */
> +	pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
> +	reg &= ~SW1x_STBY_MASK;
> +	reg |= SW1x_0_975V;
> +	pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
> +
> +	/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
> +	pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
> +	reg &= ~SW1xCONF_DVSSPEED_MASK;
> +	reg |= SW1xCONF_DVSSPEED_4US;
> +	pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
> +
> +	return p;
> +}
> +
> +static int pfuze_mode_init(struct pmic *p, u32 mode)
> +{
> +	unsigned char offset, i, switch_num;
> +	u32 id;
> +	int ret;
> +
> +	pmic_reg_read(p, PFUZE100_DEVICEID, &id);
> +	id = id & 0xf;
> +
> +	if (id == 0) {
> +		switch_num = 6;
> +		offset = PFUZE100_SW1CMODE;
> +	} else if (id == 1) {
> +		switch_num = 4;
> +		offset = PFUZE100_SW2MODE;
> +	} else {
> +		printf("Not supported, id=%d\n", id);
> +		return -EINVAL;
> +	}
> +
> +	ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
> +	if (ret < 0) {
> +		printf("Set SW1AB mode error!\n");
> +		return ret;
> +	}
> +
> +	for (i = 0; i < switch_num - 1; i++) {
> +		ret = pmic_reg_write(p, offset + i * SWITCH_SIZE, mode);
> +		if (ret < 0) {
> +			printf("Set switch 0x%x mode error!\n",
> +			       offset + i * SWITCH_SIZE);
> +			return ret;
> +		}
> +	}
> +
> +	return ret;
> +}
> +
> +int power_init_board(void)
> +{
> +	struct pmic *p;
> +	int ret;
> +
> +	p = pfuze_init(I2C_PMIC);
> +	if (!p)
> +		return -ENODEV;
> +
> +	ret = pfuze_mode_init(p, APS_PFM);
> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +#ifdef CONFIG_USB_EHCI_MX6
> +static iomux_v3_cfg_t const usb_otg_pads[] = {
> +	/* OGT1 */
> +	MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
> +	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
> +	/* OTG2 */
> +	MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
> +};
> +
> +static void setup_iomux_usb(void)
> +{
> +	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
> +					 ARRAY_SIZE(usb_otg_pads));
> +}
> +
> +int board_usb_phy_mode(int port)
> +{
> +	if (port == 1)
> +		return USB_INIT_HOST;
> +	else
> +		return usb_phy_mode(port);
> +}
> +#endif
> +
> +#ifdef CONFIG_PWM_IMX
> +static int set_pwm_leds(void)
> +{
> +	int ret;
> +
> +	imx_iomux_v3_setup_multiple_pads(pwm_led_pads,
> +					 ARRAY_SIZE(pwm_led_pads));
> +	/* enable backlight PWM 2, green LED */
> +	ret = pwm_init(1, 0, 0);
> +	if (ret)
> +		goto error;
> +	/* duty cycle 200ns, period: 8000ns */
> +	ret = pwm_config(1, 200, 8000);
> +	if (ret)
> +		goto error;
> +	ret = pwm_enable(1);
> +	if (ret)
> +		goto error;
> +
> +	/* enable backlight PWM 1, blue LED */
> +	ret = pwm_init(0, 0, 0);
> +	if (ret)
> +		goto error;
> +	/* duty cycle 200ns, period: 8000ns */
> +	ret = pwm_config(0, 200, 8000);
> +	if (ret)
> +		goto error;
> +	ret = pwm_enable(0);
> +	if (ret)
> +		goto error;
> +
> +	/* enable backlight PWM 6, red LED */
> +	ret = pwm_init(5, 0, 0);
> +	if (ret)
> +		goto error;
> +	/* duty cycle 200ns, period: 8000ns */
> +	ret = pwm_config(5, 200, 8000);
> +	if (ret)
> +		goto error;
> +	ret = pwm_enable(5);
> +
> +error:
> +	return ret;
> +}
> +#else
> +static int set_pwm_leds(void)
> +{
> +	return 0;
> +}
> +#endif
> +
> +#define ADCx_HC0        0x00
> +#define ADCx_HS         0x08
> +#define ADCx_HS_C0      BIT(0)
> +#define ADCx_R0         0x0c
> +#define ADCx_CFG        0x14
> +#define ADCx_CFG_SWMODE 0x308
> +#define ADCx_GC         0x18
> +#define ADCx_GC_CAL     BIT(7)
> +
> +static int read_adc(u32 *val)
> +{
> +	int ret;
> +	void __iomem *b = map_physmem(ADC1_BASE_ADDR, 0x100, MAP_NOCACHE);
> +
> +	/* use software mode */
> +	writel(ADCx_CFG_SWMODE, b + ADCx_CFG);
> +
> +	/* start auto calibration */
> +	setbits_le32(b + ADCx_GC, ADCx_GC_CAL);
> +	ret = wait_for_bit("ADC", b + ADCx_GC, ADCx_GC_CAL, ADCx_GC_CAL, 10, 0);
> +	if (ret)
> +		goto adc_exit;
> +
> +	/* start conversion */
> +	writel(0, b + ADCx_HC0);
> +
> +	/* wait for conversion */
> +	ret = wait_for_bit("ADC", b + ADCx_HS, ADCx_HS_C0, ADCx_HS_C0, 10, 0);
> +	if (ret)
> +		goto adc_exit;
> +
> +	/* read result */
> +	*val = readl(b + ADCx_R0);
> +
> +adc_exit:
> +	if (ret)
> +		printf("ADC failure (ret=%i)\n", ret);
> +	unmap_physmem(b, MAP_NOCACHE);
> +	return ret;
> +}
> +
> +#define VAL_UPPER	2498
> +#define VAL_LOWER	1550
> +
> +static int set_pin_state(void)
> +{
> +	u32 val;
> +	int ret;
> +
> +	ret = read_adc(&val);
> +	if (ret)
> +		return ret;
> +
> +	if (val >= VAL_UPPER)
> +		setenv("pin_state", "connected");
> +	else if (val < VAL_UPPER && val > VAL_LOWER)
> +		setenv("pin_state", "open");
> +	else
> +		setenv("pin_state", "button");
> +
> +	return ret;
> +}
> +
> +int board_late_init(void)
> +{
> +	int ret;
> +
> +	ret = set_pwm_leds();
> +	if (ret)
> +		return ret;
> +
> +	ret = set_pin_state();
> +
> +	return ret;
> +}
> +
> +int board_early_init_f(void)
> +{
> +	setup_iomux_uart();
> +
> +	setup_iomux_usb();
> +
> +	return 0;
> +}
> +
> +static struct fsl_esdhc_cfg usdhc_cfg[2] = {
> +	{USDHC4_BASE_ADDR, 0, 8},
> +	{USDHC2_BASE_ADDR, 0, 4},
> +};
> +
> +#define USDHC2_CD_GPIO IMX_GPIO_NR(3, 28)
> +
> +int board_mmc_getcd(struct mmc *mmc)
> +{
> +	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
> +
> +	if (cfg->esdhc_base == USDHC4_BASE_ADDR)
> +		return 1;
> +	if (cfg->esdhc_base == USDHC2_BASE_ADDR)
> +		return !gpio_get_value(USDHC2_CD_GPIO);
> +
> +	return -EINVAL;
> +}
> +
> +int board_mmc_init(bd_t *bis)
> +{
> +	int ret;
> +
> +	/*
> +	 * According to the board_mmc_init() the following map is done:
> +	 * (U-Boot device node)    (Physical Port)
> +	 * mmc0                    USDHC4
> +	 * mmc1                    USDHC2
> +	 */
> +	imx_iomux_v3_setup_multiple_pads(
> +		usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
> +	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
> +
> +	imx_iomux_v3_setup_multiple_pads(
> +		usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
> +	gpio_direction_input(USDHC2_CD_GPIO);
> +	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
> +
> +	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
> +	if (ret) {
> +		printf("Warning: failed to initialize USDHC4\n");
> +		return ret;
> +	}
> +
> +	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
> +	if (ret) {
> +		printf("Warning: failed to initialize USDHC2\n");
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +int board_init(void)
> +{
> +	/* Address of boot parameters */
> +	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
> +
> +#ifdef CONFIG_SYS_I2C_MXC
> +	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
> +#endif
> +
> +	return 0;
> +}
> +
> +int checkboard(void)
> +{
> +	puts("Board: VIN|ING 2000\n");
> +
> +	return 0;
> +}
> diff --git a/configs/vining_2000_defconfig b/configs/vining_2000_defconfig
> new file mode 100644
> index 0000000..b1f64f1
> --- /dev/null
> +++ b/configs/vining_2000_defconfig
> @@ -0,0 +1,31 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_MX6=y
> +CONFIG_TARGET_SAMTEC_VINING_2000=y
> +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/samtec/vining_2000/imximage.cfg"
> +CONFIG_BOOTDELAY=0
> +CONFIG_CONSOLE_MUX is not set
> +CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> +CONFIG_HUSH_PARSER=y
> +CONFIG_CMD_BOOTZ=y
> +# CONFIG_CMD_IMLS is not set
> +# CONFIG_CMD_FLASH is not set
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_GPIO=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_DHCP=y
> +CONFIG_CMD_MII=y
> +CONFIG_CMD_PING=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_EXT2=y
> +CONFIG_CMD_EXT4=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_CMD_FAT=y
> +CONFIG_CMD_FS_GENERIC=y
> +CONFIG_PCI=y
> +CONFIG_USB=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_OF_LIBFDT=y
> +CONFIG_MXC_USB_OTG_HACTIVE=y
> diff --git a/include/configs/vining_2000.h b/include/configs/vining_2000.h
> new file mode 100644
> index 0000000..235574d
> --- /dev/null
> +++ b/include/configs/vining_2000.h
> @@ -0,0 +1,123 @@
> +/*
> + * Copyright (C) 2016 samtec automotive software & electronics gmbh
> + *
> + * Configuration settings for the Samtec VIN|ING 2000 board.
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#include "mx6_common.h"
> +
> +#ifdef CONFIG_SPL
> +#include "imx6_spl.h"
> +#endif
> +
> +/* Size of malloc() pool */
> +#define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
> +
> +#define CONFIG_BOARD_EARLY_INIT_F
> +
> +#define CONFIG_MXC_UART
> +#define CONFIG_MXC_UART_BASE		UART1_BASE
> +
> +#define BOOT_TARGET_DEVICES(func) \
> +	func(MMC, mmc, 0) \
> +	func(MMC, mmc, 1) \
> +	func(USB, usb, 0) \
> +	func(PXE, pxe, na) \
> +	func(DHCP, dhcp, na)
> +#include <config_distro_bootcmd.h>
> +
> +/* Miscellaneous configurable options */
> +#define CONFIG_SYS_MEMTEST_START	0x80000000
> +#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)
> +
> +#define CONFIG_STACKSIZE		SZ_128K
> +
> +/* Physical Memory Map */
> +#define CONFIG_NR_DRAM_BANKS		1
> +#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
> +
> +#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
> +#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
> +#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
> +
> +#define CONFIG_SYS_INIT_SP_OFFSET \
> +	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SYS_INIT_SP_ADDR \
> +	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> +
> +/* MMC Configuration */
> +#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC4_BASE_ADDR
> +
> +/* I2C Configs */
> +#define CONFIG_SYS_I2C
> +#define CONFIG_SYS_I2C_MXC
> +#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
> +#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
> +#define CONFIG_SYS_I2C_SPEED		  100000
> +
> +/* PMIC */
> +#define CONFIG_POWER
> +#define CONFIG_POWER_I2C
> +#define CONFIG_POWER_PFUZE100
> +#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
> +
> +/* Network */
> +#define CONFIG_FEC_MXC
> +#define CONFIG_MII
> +
> +#define IMX_FEC_BASE			ENET_BASE_ADDR
> +#define CONFIG_FEC_MXC_PHYADDR          0x0
> +
> +#define CONFIG_FEC_XCV_TYPE             RMII
> +#define CONFIG_ETHPRIME                 "FEC"
> +
> +#define CONFIG_PHYLIB
> +#define CONFIG_PHY_ATHEROS
> +
> +#ifdef CONFIG_CMD_USB
> +#define CONFIG_USB_EHCI
> +#define CONFIG_USB_EHCI_MX6
> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
> +#define CONFIG_USB_HOST_ETHER
> +#define CONFIG_USB_ETHER_ASIX
> +#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
> +#define CONFIG_MXC_USB_FLAGS   0
> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
> +#endif
> +
> +#define CONFIG_CMD_PCI
> +#ifdef CONFIG_CMD_PCI
> +#define CONFIG_PCI_SCAN_SHOW
> +#define CONFIG_PCIE_IMX
> +#define CONFIG_PCIE_IMX_PERST_GPIO	IMX_GPIO_NR(4, 6)
> +#endif
> +
> +#define CONFIG_IMX_THERMAL
> +
> +#define CONFIG_PWM_IMX
> +#define CONFIG_IMX6_PWM_PER_CLK 66000000
> +#define CONFIG_BOARD_LATE_INIT
> +
> +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> +#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
> +#define CONFIG_ENV_SIZE			SZ_8K
> +#define CONFIG_ENV_OFFSET_REDUND	(9 * SZ_64K)
> +#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
> +#define CONFIG_ENV_IS_IN_MMC
> +
> +#ifdef CONFIG_ENV_IS_IN_MMC
> +#define CONFIG_SUPPORT_EMMC_BOOT
> +#define CONFIG_EFI_PARTITION
> +#define CONFIG_DOS_PARTITION
> +#define CONFIG_SUPPORT_EMMC_RPMB
> +#define CONFIG_SYS_MMC_ENV_DEV		0 /* USDHC4 eMMC */
> +/* 0=user, 1=boot0, 2=boot1, * 4..7=general0..3. */
> +#define CONFIG_SYS_MMC_ENV_PART		1 /* boot0 */
> +#endif
> +
> +#endif				/* __CONFIG_H */
> 

Reviewed-by: Stefano Babic <sbabic@denx.de>

Best regards,
Stefano Babic
Marek Vasut Nov. 29, 2016, 5:24 p.m. UTC | #2 
On 11/29/2016 04:21 PM, Stefano Babic wrote:
> On 29/11/2016 16:13, Christoph Fritz wrote:
>> This patch adds initial support for Samtec VIN|ING 2000 board.
>>
>> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
>> ---
>> Changes since v1:
>>  - add more comments (enet phy init)
>>  - fix layout style e.g. multi-line-comments
>>  - use pinmux macros
>>  - use helper funcs clrsetbits_le32() and wait_for_bit()
>>  - make some functions static
>>  - drop board_ehci_hcd_init() and board_phy_config()
>>  - simplify environment
>> Changes since v2:
>>  - adapt error handling in board_eth_init() and read_adc()
>>  - purge unused macros
>>  - use config_distro_bootcmd as environment
>>  - fix CONFIG_PWM_IMX undef handling
>> Changes since v3:
>>  - fix comment spelling
>>  - use u32
>>  - rearrange if condition
>> Changes since v4:
>>  - use parent error codes
>>  - rename config string to TARGET_SAMTEC_VINING_2000
>> Changes since v5:
>>  - simplify board_eth_init() error message
>>
>>  arch/arm/cpu/armv7/mx6/Kconfig         |   7 +
>>  board/samtec/vining_2000/Kconfig       |  12 +
>>  board/samtec/vining_2000/MAINTAINERS   |   6 +
>>  board/samtec/vining_2000/Makefile      |   6 +
>>  board/samtec/vining_2000/imximage.cfg  | 132 +++++++++
>>  board/samtec/vining_2000/vining_2000.c | 517 +++++++++++++++++++++++++++++++++
>>  configs/vining_2000_defconfig          |  31 ++
>>  include/configs/vining_2000.h          | 123 ++++++++
>>  8 files changed, 834 insertions(+)
>>  create mode 100644 board/samtec/vining_2000/Kconfig
>>  create mode 100644 board/samtec/vining_2000/MAINTAINERS
>>  create mode 100644 board/samtec/vining_2000/Makefile
>>  create mode 100644 board/samtec/vining_2000/imximage.cfg
>>  create mode 100644 board/samtec/vining_2000/vining_2000.c
>>  create mode 100644 configs/vining_2000_defconfig
>>  create mode 100644 include/configs/vining_2000.h
>>
>> diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
>> index 762a581..057b8cd 100644
>> --- a/arch/arm/cpu/armv7/mx6/Kconfig
>> +++ b/arch/arm/cpu/armv7/mx6/Kconfig
>> @@ -192,6 +192,12 @@ config TARGET_UDOO
>>  	bool "udoo"
>>  	select SUPPORT_SPL
>>  
>> +config TARGET_SAMTEC_VINING_2000
>> +	bool "samtec VIN|ING 2000"
>> +	select MX6SX
>> +	select DM
>> +	select DM_THERMAL
>> +
>>  config TARGET_WANDBOARD
>>  	bool "wandboard"
>>  	select SUPPORT_SPL
>> @@ -247,6 +253,7 @@ source "board/freescale/mx6ullevk/Kconfig"
>>  source "board/phytec/pcm058/Kconfig"
>>  source "board/gateworks/gw_ventana/Kconfig"
>>  source "board/kosagi/novena/Kconfig"
>> +source "board/samtec/vining_2000/Kconfig"
>>  source "board/seco/Kconfig"
>>  source "board/solidrun/mx6cuboxi/Kconfig"
>>  source "board/technexion/pico-imx6ul/Kconfig"
>> diff --git a/board/samtec/vining_2000/Kconfig b/board/samtec/vining_2000/Kconfig
>> new file mode 100644
>> index 0000000..3447c27
>> --- /dev/null
>> +++ b/board/samtec/vining_2000/Kconfig
>> @@ -0,0 +1,12 @@
>> +if TARGET_SAMTEC_VINING_2000
>> +
>> +config SYS_BOARD
>> +	default "vining_2000"
>> +
>> +config SYS_VENDOR
>> +	default "samtec"
>> +
>> +config SYS_CONFIG_NAME
>> +	default "vining_2000"
>> +
>> +endif
>> diff --git a/board/samtec/vining_2000/MAINTAINERS b/board/samtec/vining_2000/MAINTAINERS
>> new file mode 100644
>> index 0000000..027e527
>> --- /dev/null
>> +++ b/board/samtec/vining_2000/MAINTAINERS
>> @@ -0,0 +1,6 @@
>> +VINING_2000 BOARD
>> +M:	Ingo Schroeck <open-source@samtec.de>
>> +S:	Maintained
>> +F:	board/samtec/vining_2000/
>> +F:	include/configs/vining_2000.h
>> +F:	configs/vining_2000_defconfig
>> diff --git a/board/samtec/vining_2000/Makefile b/board/samtec/vining_2000/Makefile
>> new file mode 100644
>> index 0000000..1b32f66
>> --- /dev/null
>> +++ b/board/samtec/vining_2000/Makefile
>> @@ -0,0 +1,6 @@
>> +# (C) Copyright 2016 samtec automotive software & electronics gmbh
>> +#
>> +# SPDX-License-Identifier:	GPL-2.0+
>> +#
>> +
>> +obj-y  := vining_2000.o
>> diff --git a/board/samtec/vining_2000/imximage.cfg b/board/samtec/vining_2000/imximage.cfg
>> new file mode 100644
>> index 0000000..4133dda
>> --- /dev/null
>> +++ b/board/samtec/vining_2000/imximage.cfg
>> @@ -0,0 +1,132 @@
>> +/*
>> + * Copyright (C) 2016 samtec automotive software & electronics gmbh
>> + *
>> + * SPDX-License-Identifier:	GPL-2.0+
>> + */
>> +
>> +#define __ASSEMBLY__
>> +#include <config.h>
>> +
>> +/* image version */
>> +
>> +IMAGE_VERSION 2
>> +
>> +/*
>> + * Boot Device : one of
>> + * spi/sd/nand/onenand, qspi/nor
>> + */
>> +
>> +BOOT_FROM	sd
>> +
>> +/*
>> + * Device Configuration Data (DCD)
>> + *
>> + * Each entry must have the format:
>> + * Addr-type           Address        Value
>> + *
>> + * where:
>> + *	Addr-type register length (1,2 or 4 bytes)
>> + *	Address	  absolute address of the register
>> + *	value	  value to be stored in the register
>> + */
>> +
>> +/* Enable all clocks */
>> +DATA 4 0x020c4068 0xffffffff
>> +DATA 4 0x020c406c 0xffffffff
>> +DATA 4 0x020c4070 0xffffffff
>> +DATA 4 0x020c4074 0xffffffff
>> +DATA 4 0x020c4078 0xffffffff
>> +DATA 4 0x020c407c 0xffffffff
>> +DATA 4 0x020c4080 0xffffffff
>> +DATA 4 0x020c4084 0xffffffff
>> +
>> +/* IOMUX - DDR IO Type */
>> +DATA 4 0x020e0618 0x000c0000
>> +DATA 4 0x020e05fc 0x00000000
>> +
>> +/* Clock */
>> +DATA 4 0x020e032c 0x00000030
>> +
>> +/* Address */
>> +DATA 4 0x020e0300 0x00000028
>> +DATA 4 0x020e02fc 0x00000028
>> +DATA 4 0x020e05f4 0x00000028
>> +
>> +/* Control */
>> +DATA 4 0x020e0340 0x00000028
>> +
>> +DATA 4 0x020e0320 0x00000000
>> +DATA 4 0x020e0310 0x00000028
>> +DATA 4 0x020e0314 0x00000028
>> +DATA 4 0x020e0614 0x00000028
>> +
>> +/* Data Strobe */
>> +DATA 4 0x020e05f8 0x00020000
>> +DATA 4 0x020e0330 0x00000028
>> +DATA 4 0x020e0334 0x00000028
>> +DATA 4 0x020e0338 0x00000028
>> +DATA 4 0x020e033c 0x00000028
>> +
>> +/* Data */
>> +DATA 4 0x020e0608 0x00020000
>> +DATA 4 0x020e060c 0x00000028
>> +DATA 4 0x020e0610 0x00000028
>> +DATA 4 0x020e061c 0x00000028
>> +DATA 4 0x020e0620 0x00000028
>> +DATA 4 0x020e02ec 0x00000028
>> +DATA 4 0x020e02f0 0x00000028
>> +DATA 4 0x020e02f4 0x00000028
>> +DATA 4 0x020e02f8 0x00000028
>> +
>> +/* Calibrations - ZQ */
>> +DATA 4 0x021b0800 0xa1390003
>> +
>> +/* Write leveling */
>> +DATA 4 0x021b080c 0x00290025
>> +DATA 4 0x021b0810 0x00210022
>> +
>> +/* DQS Read Gate */
>> +DATA 4 0x021b083c 0x4142013a
>> +DATA 4 0x021b0840 0x012e0123
>> +
>> +/* Read/Write Delay */
>> +DATA 4 0x021b0848 0x43474949
>> +DATA 4 0x021b0850 0x38383c38
>> +
>> +/* Read data bit delay */
>> +DATA 4 0x021b081c 0x33333333
>> +DATA 4 0x021b0820 0x33333333
>> +DATA 4 0x021b0824 0x33333333
>> +DATA 4 0x021b0828 0x33333333
>> +
>> +/* Complete calibration by forced measurement */
>> +DATA 4 0x021b08b8 0x00000800
>> +
>> +/* MMDC init - DDR3, 64-bit mode, only MMDC0 is initiated */
>> +DATA 4 0x021b0004 0x0002002d
>> +DATA 4 0x021b0008 0x00333040
>> +DATA 4 0x021b000c 0x676b52f2
>> +DATA 4 0x021b0010 0x926e8b63
>> +DATA 4 0x021b0014 0x01ff00db
>> +DATA 4 0x021b0018 0x00011740
>> +DATA 4 0x021b001c 0x00008000
>> +DATA 4 0x021b002c 0x000026d2
>> +DATA 4 0x021b0030 0x006b1023
>> +DATA 4 0x021b0040 0x0000005f
>> +DATA 4 0x021b0000 0x84190000
>> +
>> +/* Initialize MT41K256M16HA-125 - MR2 */
>> +DATA 4 0x021b001c 0x02008032
>> +/* MR3 */
>> +DATA 4 0x021b001c 0x00008033
>> +/* MR1 */
>> +DATA 4 0x021b001c 0x00048031
>> +/* MR0 */
>> +DATA 4 0x021b001c 0x15108030
>> +/* DDR device ZQ calibration */
>> +DATA 4 0x021b001c 0x04008040
>> +
>> +/* Final DDR setup, before operation start */
>> +DATA 4 0x021b0020 0x00007800
>> +DATA 4 0x021b0818 0x00022227
>> +DATA 4 0x021b001c 0x00000000
>> diff --git a/board/samtec/vining_2000/vining_2000.c b/board/samtec/vining_2000/vining_2000.c
>> new file mode 100644
>> index 0000000..c92f37c
>> --- /dev/null
>> +++ b/board/samtec/vining_2000/vining_2000.c
>> @@ -0,0 +1,517 @@
>> +/*
>> + * Copyright (C) 2016 samtec automotive software & electronics gmbh
>> + *
>> + * Author: Christoph Fritz <chf.fritz@googlemail.com>
>> + *
>> + * SPDX-License-Identifier:	GPL-2.0+
>> + */
>> +
>> +#include <asm/arch/clock.h>
>> +#include <asm/arch/crm_regs.h>
>> +#include <asm/arch/iomux.h>
>> +#include <asm/arch/imx-regs.h>
>> +#include <asm/arch/mx6-pins.h>
>> +#include <asm/arch/sys_proto.h>
>> +#include <asm/gpio.h>
>> +#include <asm/imx-common/iomux-v3.h>
>> +#include <asm/io.h>
>> +#include <asm/imx-common/mxc_i2c.h>
>> +#include <linux/sizes.h>
>> +#include <common.h>
>> +#include <fsl_esdhc.h>
>> +#include <mmc.h>
>> +#include <i2c.h>
>> +#include <miiphy.h>
>> +#include <netdev.h>
>> +#include <power/pmic.h>
>> +#include <power/pfuze100_pmic.h>
>> +#include <usb.h>
>> +#include <usb/ehci-ci.h>
>> +#include <pwm.h>
>> +#include <wait_bit.h>
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +#define UART_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
>> +	PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |	\
>> +	PAD_CTL_SRE_FAST)
>> +
>> +#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PKE |	\
>> +	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm |		\
>> +	PAD_CTL_SRE_FAST)
>> +
>> +#define ENET_CLK_PAD_CTRL  PAD_CTL_DSE_34ohm
>> +
>> +#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE |			\
>> +	PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_HIGH |		\
>> +	PAD_CTL_SRE_FAST)
>> +
>> +#define I2C_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
>> +	PAD_CTL_PKE | PAD_CTL_ODE | PAD_CTL_SPEED_MED |		\
>> +	PAD_CTL_DSE_40ohm)
>> +
>> +#define USDHC_CLK_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_SPEED_MED |	\
>> +	PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST)
>> +
>> +#define USDHC_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP |	\
>> +	PAD_CTL_PKE |  PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm |	\
>> +	PAD_CTL_SRE_FAST)
>> +
>> +#define GPIO_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
>> +	PAD_CTL_PKE)
>> +
>> +int dram_init(void)
>> +{
>> +	gd->ram_size = imx_ddr_size();
>> +
>> +	return 0;
>> +}
>> +
>> +static iomux_v3_cfg_t const uart1_pads[] = {
>> +	MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
>> +	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
>> +};
>> +
>> +static iomux_v3_cfg_t const usdhc2_pads[] = {
>> +	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
>> +	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_LCD1_VSYNC__GPIO3_IO_28 | MUX_PAD_CTRL(GPIO_PAD_CTRL),
>> +};
>> +
>> +static iomux_v3_cfg_t const usdhc4_pads[] = {
>> +	MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
>> +	MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +	MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>> +};
>> +
>> +static iomux_v3_cfg_t const fec1_pads[] = {
>> +	MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
>> +	MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
>> +	MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>> +	MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>> +	MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>> +	MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>> +	MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>> +	MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
>> +	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL) |
>> +		MUX_MODE_SION,
>> +	/* LAN8720 PHY Reset */
>> +	MX6_PAD_RGMII1_TD3__GPIO5_IO_9 | MUX_PAD_CTRL(NO_PAD_CTRL),
>> +};
>> +
>> +static iomux_v3_cfg_t const pwm_led_pads[] = {
>> +	MX6_PAD_RGMII2_RD2__PWM2_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* green */
>> +	MX6_PAD_RGMII2_TD2__PWM6_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* red */
>> +	MX6_PAD_RGMII2_RD3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* blue */
>> +};
>> +
>> +static void setup_iomux_uart(void)
>> +{
>> +	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
>> +}
>> +
>> +#define PHY_RESET IMX_GPIO_NR(5, 9)
>> +
>> +int board_eth_init(bd_t *bis)
>> +{
>> +	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
>> +	int ret;
>> +	unsigned char eth1addr[6];
>> +
>> +	/* just to get secound mac address */
>> +	imx_get_mac_from_fuse(1, eth1addr);
>> +	if (!getenv("eth1addr") && is_valid_ethaddr(eth1addr))
>> +		eth_setenv_enetaddr("eth1addr", eth1addr);
>> +
>> +	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
>> +
>> +	/*
>> +	 * Generate phy reference clock via pin IOMUX ENET_REF_CLK1/2 by erasing
>> +	 * ENET1/2_TX_CLK_DIR gpr1[14:13], so that reference clock is driven by
>> +	 * ref_enetpll0/1 and enable ENET1/2_TX_CLK output driver.
>> +	 */
>> +	clrsetbits_le32(&iomuxc_regs->gpr[1],
>> +			IOMUX_GPR1_FEC1_CLOCK_MUX2_SEL_MASK |
>> +			IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK,
>> +			IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK |
>> +			IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
>> +
>> +	ret = enable_fec_anatop_clock(0, ENET_50MHZ);
>> +	if (ret)
>> +		goto eth_fail;
>> +
>> +	/* reset phy */
>> +	gpio_direction_output(PHY_RESET, 0);
>> +	mdelay(16);
>> +	gpio_set_value(PHY_RESET, 1);
>> +	mdelay(1);
>> +
>> +	ret = fecmxc_initialize_multi(bis, 0, CONFIG_FEC_MXC_PHYADDR,
>> +					IMX_FEC_BASE);
>> +	if (ret)
>> +		goto eth_fail;
>> +
>> +	return ret;
>> +
>> +eth_fail:
>> +	printf("FEC MXC: %s:failed (%i)\n", __func__, ret);
>> +	gpio_set_value(PHY_RESET, 0);
>> +	return ret;
>> +}
>> +
>> +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
>> +/* I2C1 for PMIC */
>> +static struct i2c_pads_info i2c_pad_info1 = {
>> +	.scl = {
>> +		.i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
>> +		.gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
>> +		.gp = IMX_GPIO_NR(1, 0),
>> +	},
>> +	.sda = {
>> +		.i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
>> +		.gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
>> +		.gp = IMX_GPIO_NR(1, 1),
>> +	},
>> +};
>> +
>> +static struct pmic *pfuze_init(unsigned char i2cbus)
>> +{
>> +	struct pmic *p;
>> +	int ret;
>> +	u32 reg;
>> +
>> +	ret = power_pfuze100_init(i2cbus);
>> +	if (ret)
>> +		return NULL;
>> +
>> +	p = pmic_get("PFUZE100");
>> +	ret = pmic_probe(p);
>> +	if (ret)
>> +		return NULL;
>> +
>> +	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
>> +	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
>> +
>> +	/* Set SW1AB stanby volage to 0.975V */
>> +	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
>> +	reg &= ~SW1x_STBY_MASK;
>> +	reg |= SW1x_0_975V;
>> +	pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
>> +
>> +	/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
>> +	pmic_reg_read(p, PFUZE100_SW1ABCONF, &reg);
>> +	reg &= ~SW1xCONF_DVSSPEED_MASK;
>> +	reg |= SW1xCONF_DVSSPEED_4US;
>> +	pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
>> +
>> +	/* Set SW1C standby voltage to 0.975V */
>> +	pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
>> +	reg &= ~SW1x_STBY_MASK;
>> +	reg |= SW1x_0_975V;
>> +	pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
>> +
>> +	/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
>> +	pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
>> +	reg &= ~SW1xCONF_DVSSPEED_MASK;
>> +	reg |= SW1xCONF_DVSSPEED_4US;
>> +	pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
>> +
>> +	return p;
>> +}
>> +
>> +static int pfuze_mode_init(struct pmic *p, u32 mode)
>> +{
>> +	unsigned char offset, i, switch_num;
>> +	u32 id;
>> +	int ret;
>> +
>> +	pmic_reg_read(p, PFUZE100_DEVICEID, &id);
>> +	id = id & 0xf;
>> +
>> +	if (id == 0) {
>> +		switch_num = 6;
>> +		offset = PFUZE100_SW1CMODE;
>> +	} else if (id == 1) {
>> +		switch_num = 4;
>> +		offset = PFUZE100_SW2MODE;
>> +	} else {
>> +		printf("Not supported, id=%d\n", id);
>> +		return -EINVAL;
>> +	}
>> +
>> +	ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
>> +	if (ret < 0) {
>> +		printf("Set SW1AB mode error!\n");
>> +		return ret;
>> +	}
>> +
>> +	for (i = 0; i < switch_num - 1; i++) {
>> +		ret = pmic_reg_write(p, offset + i * SWITCH_SIZE, mode);
>> +		if (ret < 0) {
>> +			printf("Set switch 0x%x mode error!\n",
>> +			       offset + i * SWITCH_SIZE);
>> +			return ret;
>> +		}
>> +	}
>> +
>> +	return ret;
>> +}
>> +
>> +int power_init_board(void)
>> +{
>> +	struct pmic *p;
>> +	int ret;
>> +
>> +	p = pfuze_init(I2C_PMIC);
>> +	if (!p)
>> +		return -ENODEV;
>> +
>> +	ret = pfuze_mode_init(p, APS_PFM);
>> +	if (ret < 0)
>> +		return ret;
>> +
>> +	return 0;
>> +}
>> +
>> +#ifdef CONFIG_USB_EHCI_MX6
>> +static iomux_v3_cfg_t const usb_otg_pads[] = {
>> +	/* OGT1 */
>> +	MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
>> +	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
>> +	/* OTG2 */
>> +	MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
>> +};
>> +
>> +static void setup_iomux_usb(void)
>> +{
>> +	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
>> +					 ARRAY_SIZE(usb_otg_pads));
>> +}
>> +
>> +int board_usb_phy_mode(int port)
>> +{
>> +	if (port == 1)
>> +		return USB_INIT_HOST;
>> +	else
>> +		return usb_phy_mode(port);
>> +}
>> +#endif
>> +
>> +#ifdef CONFIG_PWM_IMX
>> +static int set_pwm_leds(void)
>> +{
>> +	int ret;
>> +
>> +	imx_iomux_v3_setup_multiple_pads(pwm_led_pads,
>> +					 ARRAY_SIZE(pwm_led_pads));
>> +	/* enable backlight PWM 2, green LED */
>> +	ret = pwm_init(1, 0, 0);
>> +	if (ret)
>> +		goto error;
>> +	/* duty cycle 200ns, period: 8000ns */
>> +	ret = pwm_config(1, 200, 8000);
>> +	if (ret)
>> +		goto error;
>> +	ret = pwm_enable(1);
>> +	if (ret)
>> +		goto error;
>> +
>> +	/* enable backlight PWM 1, blue LED */
>> +	ret = pwm_init(0, 0, 0);
>> +	if (ret)
>> +		goto error;
>> +	/* duty cycle 200ns, period: 8000ns */
>> +	ret = pwm_config(0, 200, 8000);
>> +	if (ret)
>> +		goto error;
>> +	ret = pwm_enable(0);
>> +	if (ret)
>> +		goto error;
>> +
>> +	/* enable backlight PWM 6, red LED */
>> +	ret = pwm_init(5, 0, 0);
>> +	if (ret)
>> +		goto error;
>> +	/* duty cycle 200ns, period: 8000ns */
>> +	ret = pwm_config(5, 200, 8000);
>> +	if (ret)
>> +		goto error;
>> +	ret = pwm_enable(5);
>> +
>> +error:
>> +	return ret;
>> +}
>> +#else
>> +static int set_pwm_leds(void)
>> +{
>> +	return 0;
>> +}
>> +#endif
>> +
>> +#define ADCx_HC0        0x00
>> +#define ADCx_HS         0x08
>> +#define ADCx_HS_C0      BIT(0)
>> +#define ADCx_R0         0x0c
>> +#define ADCx_CFG        0x14
>> +#define ADCx_CFG_SWMODE 0x308
>> +#define ADCx_GC         0x18
>> +#define ADCx_GC_CAL     BIT(7)
>> +
>> +static int read_adc(u32 *val)
>> +{
>> +	int ret;
>> +	void __iomem *b = map_physmem(ADC1_BASE_ADDR, 0x100, MAP_NOCACHE);
>> +
>> +	/* use software mode */
>> +	writel(ADCx_CFG_SWMODE, b + ADCx_CFG);
>> +
>> +	/* start auto calibration */
>> +	setbits_le32(b + ADCx_GC, ADCx_GC_CAL);
>> +	ret = wait_for_bit("ADC", b + ADCx_GC, ADCx_GC_CAL, ADCx_GC_CAL, 10, 0);
>> +	if (ret)
>> +		goto adc_exit;
>> +
>> +	/* start conversion */
>> +	writel(0, b + ADCx_HC0);
>> +
>> +	/* wait for conversion */
>> +	ret = wait_for_bit("ADC", b + ADCx_HS, ADCx_HS_C0, ADCx_HS_C0, 10, 0);
>> +	if (ret)
>> +		goto adc_exit;
>> +
>> +	/* read result */
>> +	*val = readl(b + ADCx_R0);
>> +
>> +adc_exit:
>> +	if (ret)
>> +		printf("ADC failure (ret=%i)\n", ret);
>> +	unmap_physmem(b, MAP_NOCACHE);
>> +	return ret;
>> +}
>> +
>> +#define VAL_UPPER	2498
>> +#define VAL_LOWER	1550
>> +
>> +static int set_pin_state(void)
>> +{
>> +	u32 val;
>> +	int ret;
>> +
>> +	ret = read_adc(&val);
>> +	if (ret)
>> +		return ret;
>> +
>> +	if (val >= VAL_UPPER)
>> +		setenv("pin_state", "connected");
>> +	else if (val < VAL_UPPER && val > VAL_LOWER)
>> +		setenv("pin_state", "open");
>> +	else
>> +		setenv("pin_state", "button");
>> +
>> +	return ret;
>> +}
>> +
>> +int board_late_init(void)
>> +{
>> +	int ret;
>> +
>> +	ret = set_pwm_leds();
>> +	if (ret)
>> +		return ret;
>> +
>> +	ret = set_pin_state();
>> +
>> +	return ret;
>> +}
>> +
>> +int board_early_init_f(void)
>> +{
>> +	setup_iomux_uart();
>> +
>> +	setup_iomux_usb();
>> +
>> +	return 0;
>> +}
>> +
>> +static struct fsl_esdhc_cfg usdhc_cfg[2] = {
>> +	{USDHC4_BASE_ADDR, 0, 8},
>> +	{USDHC2_BASE_ADDR, 0, 4},
>> +};
>> +
>> +#define USDHC2_CD_GPIO IMX_GPIO_NR(3, 28)
>> +
>> +int board_mmc_getcd(struct mmc *mmc)
>> +{
>> +	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
>> +
>> +	if (cfg->esdhc_base == USDHC4_BASE_ADDR)
>> +		return 1;
>> +	if (cfg->esdhc_base == USDHC2_BASE_ADDR)
>> +		return !gpio_get_value(USDHC2_CD_GPIO);
>> +
>> +	return -EINVAL;
>> +}
>> +
>> +int board_mmc_init(bd_t *bis)
>> +{
>> +	int ret;
>> +
>> +	/*
>> +	 * According to the board_mmc_init() the following map is done:
>> +	 * (U-Boot device node)    (Physical Port)
>> +	 * mmc0                    USDHC4
>> +	 * mmc1                    USDHC2
>> +	 */
>> +	imx_iomux_v3_setup_multiple_pads(
>> +		usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
>> +	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
>> +
>> +	imx_iomux_v3_setup_multiple_pads(
>> +		usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
>> +	gpio_direction_input(USDHC2_CD_GPIO);
>> +	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
>> +
>> +	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
>> +	if (ret) {
>> +		printf("Warning: failed to initialize USDHC4\n");
>> +		return ret;
>> +	}
>> +
>> +	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
>> +	if (ret) {
>> +		printf("Warning: failed to initialize USDHC2\n");
>> +		return ret;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +int board_init(void)
>> +{
>> +	/* Address of boot parameters */
>> +	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
>> +
>> +#ifdef CONFIG_SYS_I2C_MXC
>> +	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
>> +#endif
>> +
>> +	return 0;
>> +}
>> +
>> +int checkboard(void)
>> +{
>> +	puts("Board: VIN|ING 2000\n");
>> +
>> +	return 0;
>> +}
>> diff --git a/configs/vining_2000_defconfig b/configs/vining_2000_defconfig
>> new file mode 100644
>> index 0000000..b1f64f1
>> --- /dev/null
>> +++ b/configs/vining_2000_defconfig
>> @@ -0,0 +1,31 @@
>> +CONFIG_ARM=y
>> +CONFIG_ARCH_MX6=y
>> +CONFIG_TARGET_SAMTEC_VINING_2000=y
>> +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/samtec/vining_2000/imximage.cfg"
>> +CONFIG_BOOTDELAY=0
>> +CONFIG_CONSOLE_MUX is not set
>> +CONFIG_SYS_CONSOLE_IS_IN_ENV=y
>> +CONFIG_HUSH_PARSER=y
>> +CONFIG_CMD_BOOTZ=y
>> +# CONFIG_CMD_IMLS is not set
>> +# CONFIG_CMD_FLASH is not set
>> +CONFIG_CMD_MMC=y
>> +CONFIG_CMD_I2C=y
>> +CONFIG_CMD_USB=y
>> +CONFIG_CMD_GPIO=y
>> +# CONFIG_CMD_SETEXPR is not set
>> +CONFIG_CMD_DHCP=y
>> +CONFIG_CMD_MII=y
>> +CONFIG_CMD_PING=y
>> +CONFIG_CMD_CACHE=y
>> +CONFIG_CMD_TIME=y
>> +CONFIG_CMD_EXT2=y
>> +CONFIG_CMD_EXT4=y
>> +CONFIG_CMD_EXT4_WRITE=y
>> +CONFIG_CMD_FAT=y
>> +CONFIG_CMD_FS_GENERIC=y
>> +CONFIG_PCI=y
>> +CONFIG_USB=y
>> +CONFIG_USB_STORAGE=y
>> +CONFIG_OF_LIBFDT=y
>> +CONFIG_MXC_USB_OTG_HACTIVE=y
>> diff --git a/include/configs/vining_2000.h b/include/configs/vining_2000.h
>> new file mode 100644
>> index 0000000..235574d
>> --- /dev/null
>> +++ b/include/configs/vining_2000.h
>> @@ -0,0 +1,123 @@
>> +/*
>> + * Copyright (C) 2016 samtec automotive software & electronics gmbh
>> + *
>> + * Configuration settings for the Samtec VIN|ING 2000 board.
>> + *
>> + * SPDX-License-Identifier:	GPL-2.0+
>> + */
>> +
>> +#ifndef __CONFIG_H
>> +#define __CONFIG_H
>> +
>> +#include "mx6_common.h"
>> +
>> +#ifdef CONFIG_SPL
>> +#include "imx6_spl.h"
>> +#endif
>> +
>> +/* Size of malloc() pool */
>> +#define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
>> +
>> +#define CONFIG_BOARD_EARLY_INIT_F
>> +
>> +#define CONFIG_MXC_UART
>> +#define CONFIG_MXC_UART_BASE		UART1_BASE
>> +
>> +#define BOOT_TARGET_DEVICES(func) \
>> +	func(MMC, mmc, 0) \
>> +	func(MMC, mmc, 1) \
>> +	func(USB, usb, 0) \
>> +	func(PXE, pxe, na) \
>> +	func(DHCP, dhcp, na)
>> +#include <config_distro_bootcmd.h>
>> +
>> +/* Miscellaneous configurable options */
>> +#define CONFIG_SYS_MEMTEST_START	0x80000000
>> +#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)
>> +
>> +#define CONFIG_STACKSIZE		SZ_128K
>> +
>> +/* Physical Memory Map */
>> +#define CONFIG_NR_DRAM_BANKS		1
>> +#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
>> +
>> +#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
>> +#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
>> +#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
>> +
>> +#define CONFIG_SYS_INIT_SP_OFFSET \
>> +	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
>> +#define CONFIG_SYS_INIT_SP_ADDR \
>> +	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
>> +
>> +/* MMC Configuration */
>> +#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC4_BASE_ADDR
>> +
>> +/* I2C Configs */
>> +#define CONFIG_SYS_I2C
>> +#define CONFIG_SYS_I2C_MXC
>> +#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
>> +#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
>> +#define CONFIG_SYS_I2C_SPEED		  100000
>> +
>> +/* PMIC */
>> +#define CONFIG_POWER
>> +#define CONFIG_POWER_I2C
>> +#define CONFIG_POWER_PFUZE100
>> +#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
>> +
>> +/* Network */
>> +#define CONFIG_FEC_MXC
>> +#define CONFIG_MII
>> +
>> +#define IMX_FEC_BASE			ENET_BASE_ADDR
>> +#define CONFIG_FEC_MXC_PHYADDR          0x0
>> +
>> +#define CONFIG_FEC_XCV_TYPE             RMII
>> +#define CONFIG_ETHPRIME                 "FEC"
>> +
>> +#define CONFIG_PHYLIB
>> +#define CONFIG_PHY_ATHEROS
>> +
>> +#ifdef CONFIG_CMD_USB
>> +#define CONFIG_USB_EHCI
>> +#define CONFIG_USB_EHCI_MX6
>> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
>> +#define CONFIG_USB_HOST_ETHER
>> +#define CONFIG_USB_ETHER_ASIX
>> +#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
>> +#define CONFIG_MXC_USB_FLAGS   0
>> +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
>> +#endif
>> +
>> +#define CONFIG_CMD_PCI
>> +#ifdef CONFIG_CMD_PCI
>> +#define CONFIG_PCI_SCAN_SHOW
>> +#define CONFIG_PCIE_IMX
>> +#define CONFIG_PCIE_IMX_PERST_GPIO	IMX_GPIO_NR(4, 6)
>> +#endif
>> +
>> +#define CONFIG_IMX_THERMAL
>> +
>> +#define CONFIG_PWM_IMX
>> +#define CONFIG_IMX6_PWM_PER_CLK 66000000
>> +#define CONFIG_BOARD_LATE_INIT
>> +
>> +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
>> +#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
>> +#define CONFIG_ENV_SIZE			SZ_8K
>> +#define CONFIG_ENV_OFFSET_REDUND	(9 * SZ_64K)
>> +#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
>> +#define CONFIG_ENV_IS_IN_MMC
>> +
>> +#ifdef CONFIG_ENV_IS_IN_MMC
>> +#define CONFIG_SUPPORT_EMMC_BOOT
>> +#define CONFIG_EFI_PARTITION
>> +#define CONFIG_DOS_PARTITION
>> +#define CONFIG_SUPPORT_EMMC_RPMB
>> +#define CONFIG_SYS_MMC_ENV_DEV		0 /* USDHC4 eMMC */
>> +/* 0=user, 1=boot0, 2=boot1, * 4..7=general0..3. */
>> +#define CONFIG_SYS_MMC_ENV_PART		1 /* boot0 */
>> +#endif
>> +
>> +#endif				/* __CONFIG_H */
>>
> 
> Reviewed-by: Stefano Babic <sbabic@denx.de>

Acked-by: Marek Vasut <marex@denx.de>
Stefano Babic Nov. 30, 2016, 8:56 a.m. UTC | #3 
On 29/11/2016 16:13, Christoph Fritz wrote:
> This patch adds initial support for Samtec VIN|ING 2000 board.
> 
> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
> ---
> Changes since v1:
>  - add more comments (enet phy init)
>  - fix layout style e.g. multi-line-comments
>  - use pinmux macros
>  - use helper funcs clrsetbits_le32() and wait_for_bit()
>  - make some functions static
>  - drop board_ehci_hcd_init() and board_phy_config()
>  - simplify environment
> Changes since v2:
>  - adapt error handling in board_eth_init() and read_adc()
>  - purge unused macros
>  - use config_distro_bootcmd as environment
>  - fix CONFIG_PWM_IMX undef handling
> Changes since v3:
>  - fix comment spelling
>  - use u32
>  - rearrange if condition
> Changes since v4:
>  - use parent error codes
>  - rename config string to TARGET_SAMTEC_VINING_2000
> Changes since v5:
>  - simplify board_eth_init() error message
> 
>  arch/arm/cpu/armv7/mx6/Kconfig         |   7 +
>  board/samtec/vining_2000/Kconfig       |  12 +
>  board/samtec/vining_2000/MAINTAINERS   |   6 +
>  board/samtec/vining_2000/Makefile      |   6 +
>  board/samtec/vining_2000/imximage.cfg  | 132 +++++++++
>  board/samtec/vining_2000/vining_2000.c | 517 +++++++++++++++++++++++++++++++++
>  configs/vining_2000_defconfig          |  31 ++
>  include/configs/vining_2000.h          | 123 ++++++++
>  8 files changed, 834 insertions(+)
>  create mode 100644 board/samtec/vining_2000/Kconfig
>  create mode 100644 board/samtec/vining_2000/MAINTAINERS
>  create mode 100644 board/samtec/vining_2000/Makefile
>  create mode 100644 board/samtec/vining_2000/imximage.cfg
>  create mode 100644 board/samtec/vining_2000/vining_2000.c
>  create mode 100644 configs/vining_2000_defconfig
>  create mode 100644 include/configs/vining_2000.h
> 
> diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
> index 762a581..057b8cd 100644

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic
diff mbox

Patch

diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index 762a581..057b8cd 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -192,6 +192,12 @@  config TARGET_UDOO
 	bool "udoo"
 	select SUPPORT_SPL
 
+config TARGET_SAMTEC_VINING_2000
+	bool "samtec VIN|ING 2000"
+	select MX6SX
+	select DM
+	select DM_THERMAL
+
 config TARGET_WANDBOARD
 	bool "wandboard"
 	select SUPPORT_SPL
@@ -247,6 +253,7 @@  source "board/freescale/mx6ullevk/Kconfig"
 source "board/phytec/pcm058/Kconfig"
 source "board/gateworks/gw_ventana/Kconfig"
 source "board/kosagi/novena/Kconfig"
+source "board/samtec/vining_2000/Kconfig"
 source "board/seco/Kconfig"
 source "board/solidrun/mx6cuboxi/Kconfig"
 source "board/technexion/pico-imx6ul/Kconfig"
diff --git a/board/samtec/vining_2000/Kconfig b/board/samtec/vining_2000/Kconfig
new file mode 100644
index 0000000..3447c27
--- /dev/null
+++ b/board/samtec/vining_2000/Kconfig
@@ -0,0 +1,12 @@ 
+if TARGET_SAMTEC_VINING_2000
+
+config SYS_BOARD
+	default "vining_2000"
+
+config SYS_VENDOR
+	default "samtec"
+
+config SYS_CONFIG_NAME
+	default "vining_2000"
+
+endif
diff --git a/board/samtec/vining_2000/MAINTAINERS b/board/samtec/vining_2000/MAINTAINERS
new file mode 100644
index 0000000..027e527
--- /dev/null
+++ b/board/samtec/vining_2000/MAINTAINERS
@@ -0,0 +1,6 @@ 
+VINING_2000 BOARD
+M:	Ingo Schroeck <open-source@samtec.de>
+S:	Maintained
+F:	board/samtec/vining_2000/
+F:	include/configs/vining_2000.h
+F:	configs/vining_2000_defconfig
diff --git a/board/samtec/vining_2000/Makefile b/board/samtec/vining_2000/Makefile
new file mode 100644
index 0000000..1b32f66
--- /dev/null
+++ b/board/samtec/vining_2000/Makefile
@@ -0,0 +1,6 @@ 
+# (C) Copyright 2016 samtec automotive software & electronics gmbh
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := vining_2000.o
diff --git a/board/samtec/vining_2000/imximage.cfg b/board/samtec/vining_2000/imximage.cfg
new file mode 100644
index 0000000..4133dda
--- /dev/null
+++ b/board/samtec/vining_2000/imximage.cfg
@@ -0,0 +1,132 @@ 
+/*
+ * Copyright (C) 2016 samtec automotive software & electronics gmbh
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+BOOT_FROM	sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+/* Enable all clocks */
+DATA 4 0x020c4068 0xffffffff
+DATA 4 0x020c406c 0xffffffff
+DATA 4 0x020c4070 0xffffffff
+DATA 4 0x020c4074 0xffffffff
+DATA 4 0x020c4078 0xffffffff
+DATA 4 0x020c407c 0xffffffff
+DATA 4 0x020c4080 0xffffffff
+DATA 4 0x020c4084 0xffffffff
+
+/* IOMUX - DDR IO Type */
+DATA 4 0x020e0618 0x000c0000
+DATA 4 0x020e05fc 0x00000000
+
+/* Clock */
+DATA 4 0x020e032c 0x00000030
+
+/* Address */
+DATA 4 0x020e0300 0x00000028
+DATA 4 0x020e02fc 0x00000028
+DATA 4 0x020e05f4 0x00000028
+
+/* Control */
+DATA 4 0x020e0340 0x00000028
+
+DATA 4 0x020e0320 0x00000000
+DATA 4 0x020e0310 0x00000028
+DATA 4 0x020e0314 0x00000028
+DATA 4 0x020e0614 0x00000028
+
+/* Data Strobe */
+DATA 4 0x020e05f8 0x00020000
+DATA 4 0x020e0330 0x00000028
+DATA 4 0x020e0334 0x00000028
+DATA 4 0x020e0338 0x00000028
+DATA 4 0x020e033c 0x00000028
+
+/* Data */
+DATA 4 0x020e0608 0x00020000
+DATA 4 0x020e060c 0x00000028
+DATA 4 0x020e0610 0x00000028
+DATA 4 0x020e061c 0x00000028
+DATA 4 0x020e0620 0x00000028
+DATA 4 0x020e02ec 0x00000028
+DATA 4 0x020e02f0 0x00000028
+DATA 4 0x020e02f4 0x00000028
+DATA 4 0x020e02f8 0x00000028
+
+/* Calibrations - ZQ */
+DATA 4 0x021b0800 0xa1390003
+
+/* Write leveling */
+DATA 4 0x021b080c 0x00290025
+DATA 4 0x021b0810 0x00210022
+
+/* DQS Read Gate */
+DATA 4 0x021b083c 0x4142013a
+DATA 4 0x021b0840 0x012e0123
+
+/* Read/Write Delay */
+DATA 4 0x021b0848 0x43474949
+DATA 4 0x021b0850 0x38383c38
+
+/* Read data bit delay */
+DATA 4 0x021b081c 0x33333333
+DATA 4 0x021b0820 0x33333333
+DATA 4 0x021b0824 0x33333333
+DATA 4 0x021b0828 0x33333333
+
+/* Complete calibration by forced measurement */
+DATA 4 0x021b08b8 0x00000800
+
+/* MMDC init - DDR3, 64-bit mode, only MMDC0 is initiated */
+DATA 4 0x021b0004 0x0002002d
+DATA 4 0x021b0008 0x00333040
+DATA 4 0x021b000c 0x676b52f2
+DATA 4 0x021b0010 0x926e8b63
+DATA 4 0x021b0014 0x01ff00db
+DATA 4 0x021b0018 0x00011740
+DATA 4 0x021b001c 0x00008000
+DATA 4 0x021b002c 0x000026d2
+DATA 4 0x021b0030 0x006b1023
+DATA 4 0x021b0040 0x0000005f
+DATA 4 0x021b0000 0x84190000
+
+/* Initialize MT41K256M16HA-125 - MR2 */
+DATA 4 0x021b001c 0x02008032
+/* MR3 */
+DATA 4 0x021b001c 0x00008033
+/* MR1 */
+DATA 4 0x021b001c 0x00048031
+/* MR0 */
+DATA 4 0x021b001c 0x15108030
+/* DDR device ZQ calibration */
+DATA 4 0x021b001c 0x04008040
+
+/* Final DDR setup, before operation start */
+DATA 4 0x021b0020 0x00007800
+DATA 4 0x021b0818 0x00022227
+DATA 4 0x021b001c 0x00000000
diff --git a/board/samtec/vining_2000/vining_2000.c b/board/samtec/vining_2000/vining_2000.c
new file mode 100644
index 0000000..c92f37c
--- /dev/null
+++ b/board/samtec/vining_2000/vining_2000.c
@@ -0,0 +1,517 @@ 
+/*
+ * Copyright (C) 2016 samtec automotive software & electronics gmbh
+ *
+ * Author: Christoph Fritz <chf.fritz@googlemail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/io.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <linux/sizes.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+#include <pwm.h>
+#include <wait_bit.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
+	PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |	\
+	PAD_CTL_SRE_FAST)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PKE |	\
+	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm |		\
+	PAD_CTL_SRE_FAST)
+
+#define ENET_CLK_PAD_CTRL  PAD_CTL_DSE_34ohm
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE |			\
+	PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_HIGH |		\
+	PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
+	PAD_CTL_PKE | PAD_CTL_ODE | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm)
+
+#define USDHC_CLK_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_SPEED_MED |	\
+	PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST)
+
+#define USDHC_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP |	\
+	PAD_CTL_PKE |  PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm |	\
+	PAD_CTL_SRE_FAST)
+
+#define GPIO_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
+	PAD_CTL_PKE)
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
+	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_LCD1_VSYNC__GPIO3_IO_28 | MUX_PAD_CTRL(GPIO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
+	MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL) |
+		MUX_MODE_SION,
+	/* LAN8720 PHY Reset */
+	MX6_PAD_RGMII1_TD3__GPIO5_IO_9 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const pwm_led_pads[] = {
+	MX6_PAD_RGMII2_RD2__PWM2_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* green */
+	MX6_PAD_RGMII2_TD2__PWM6_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* red */
+	MX6_PAD_RGMII2_RD3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* blue */
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#define PHY_RESET IMX_GPIO_NR(5, 9)
+
+int board_eth_init(bd_t *bis)
+{
+	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+	unsigned char eth1addr[6];
+
+	/* just to get secound mac address */
+	imx_get_mac_from_fuse(1, eth1addr);
+	if (!getenv("eth1addr") && is_valid_ethaddr(eth1addr))
+		eth_setenv_enetaddr("eth1addr", eth1addr);
+
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+
+	/*
+	 * Generate phy reference clock via pin IOMUX ENET_REF_CLK1/2 by erasing
+	 * ENET1/2_TX_CLK_DIR gpr1[14:13], so that reference clock is driven by
+	 * ref_enetpll0/1 and enable ENET1/2_TX_CLK output driver.
+	 */
+	clrsetbits_le32(&iomuxc_regs->gpr[1],
+			IOMUX_GPR1_FEC1_CLOCK_MUX2_SEL_MASK |
+			IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK,
+			IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK |
+			IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+
+	ret = enable_fec_anatop_clock(0, ENET_50MHZ);
+	if (ret)
+		goto eth_fail;
+
+	/* reset phy */
+	gpio_direction_output(PHY_RESET, 0);
+	mdelay(16);
+	gpio_set_value(PHY_RESET, 1);
+	mdelay(1);
+
+	ret = fecmxc_initialize_multi(bis, 0, CONFIG_FEC_MXC_PHYADDR,
+					IMX_FEC_BASE);
+	if (ret)
+		goto eth_fail;
+
+	return ret;
+
+eth_fail:
+	printf("FEC MXC: %s:failed (%i)\n", __func__, ret);
+	gpio_set_value(PHY_RESET, 0);
+	return ret;
+}
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C1 for PMIC */
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
+		.gp = IMX_GPIO_NR(1, 0),
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
+		.gp = IMX_GPIO_NR(1, 1),
+	},
+};
+
+static struct pmic *pfuze_init(unsigned char i2cbus)
+{
+	struct pmic *p;
+	int ret;
+	u32 reg;
+
+	ret = power_pfuze100_init(i2cbus);
+	if (ret)
+		return NULL;
+
+	p = pmic_get("PFUZE100");
+	ret = pmic_probe(p);
+	if (ret)
+		return NULL;
+
+	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
+	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
+
+	/* Set SW1AB stanby volage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
+	reg &= ~SW1x_STBY_MASK;
+	reg |= SW1x_0_975V;
+	pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
+
+	/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PFUZE100_SW1ABCONF, &reg);
+	reg &= ~SW1xCONF_DVSSPEED_MASK;
+	reg |= SW1xCONF_DVSSPEED_4US;
+	pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
+
+	/* Set SW1C standby voltage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
+	reg &= ~SW1x_STBY_MASK;
+	reg |= SW1x_0_975V;
+	pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
+
+	/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
+	reg &= ~SW1xCONF_DVSSPEED_MASK;
+	reg |= SW1xCONF_DVSSPEED_4US;
+	pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
+
+	return p;
+}
+
+static int pfuze_mode_init(struct pmic *p, u32 mode)
+{
+	unsigned char offset, i, switch_num;
+	u32 id;
+	int ret;
+
+	pmic_reg_read(p, PFUZE100_DEVICEID, &id);
+	id = id & 0xf;
+
+	if (id == 0) {
+		switch_num = 6;
+		offset = PFUZE100_SW1CMODE;
+	} else if (id == 1) {
+		switch_num = 4;
+		offset = PFUZE100_SW2MODE;
+	} else {
+		printf("Not supported, id=%d\n", id);
+		return -EINVAL;
+	}
+
+	ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
+	if (ret < 0) {
+		printf("Set SW1AB mode error!\n");
+		return ret;
+	}
+
+	for (i = 0; i < switch_num - 1; i++) {
+		ret = pmic_reg_write(p, offset + i * SWITCH_SIZE, mode);
+		if (ret < 0) {
+			printf("Set switch 0x%x mode error!\n",
+			       offset + i * SWITCH_SIZE);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+int power_init_board(void)
+{
+	struct pmic *p;
+	int ret;
+
+	p = pfuze_init(I2C_PMIC);
+	if (!p)
+		return -ENODEV;
+
+	ret = pfuze_mode_init(p, APS_PFM);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+#ifdef CONFIG_USB_EHCI_MX6
+static iomux_v3_cfg_t const usb_otg_pads[] = {
+	/* OGT1 */
+	MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* OTG2 */
+	MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
+};
+
+static void setup_iomux_usb(void)
+{
+	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
+					 ARRAY_SIZE(usb_otg_pads));
+}
+
+int board_usb_phy_mode(int port)
+{
+	if (port == 1)
+		return USB_INIT_HOST;
+	else
+		return usb_phy_mode(port);
+}
+#endif
+
+#ifdef CONFIG_PWM_IMX
+static int set_pwm_leds(void)
+{
+	int ret;
+
+	imx_iomux_v3_setup_multiple_pads(pwm_led_pads,
+					 ARRAY_SIZE(pwm_led_pads));
+	/* enable backlight PWM 2, green LED */
+	ret = pwm_init(1, 0, 0);
+	if (ret)
+		goto error;
+	/* duty cycle 200ns, period: 8000ns */
+	ret = pwm_config(1, 200, 8000);
+	if (ret)
+		goto error;
+	ret = pwm_enable(1);
+	if (ret)
+		goto error;
+
+	/* enable backlight PWM 1, blue LED */
+	ret = pwm_init(0, 0, 0);
+	if (ret)
+		goto error;
+	/* duty cycle 200ns, period: 8000ns */
+	ret = pwm_config(0, 200, 8000);
+	if (ret)
+		goto error;
+	ret = pwm_enable(0);
+	if (ret)
+		goto error;
+
+	/* enable backlight PWM 6, red LED */
+	ret = pwm_init(5, 0, 0);
+	if (ret)
+		goto error;
+	/* duty cycle 200ns, period: 8000ns */
+	ret = pwm_config(5, 200, 8000);
+	if (ret)
+		goto error;
+	ret = pwm_enable(5);
+
+error:
+	return ret;
+}
+#else
+static int set_pwm_leds(void)
+{
+	return 0;
+}
+#endif
+
+#define ADCx_HC0        0x00
+#define ADCx_HS         0x08
+#define ADCx_HS_C0      BIT(0)
+#define ADCx_R0         0x0c
+#define ADCx_CFG        0x14
+#define ADCx_CFG_SWMODE 0x308
+#define ADCx_GC         0x18
+#define ADCx_GC_CAL     BIT(7)
+
+static int read_adc(u32 *val)
+{
+	int ret;
+	void __iomem *b = map_physmem(ADC1_BASE_ADDR, 0x100, MAP_NOCACHE);
+
+	/* use software mode */
+	writel(ADCx_CFG_SWMODE, b + ADCx_CFG);
+
+	/* start auto calibration */
+	setbits_le32(b + ADCx_GC, ADCx_GC_CAL);
+	ret = wait_for_bit("ADC", b + ADCx_GC, ADCx_GC_CAL, ADCx_GC_CAL, 10, 0);
+	if (ret)
+		goto adc_exit;
+
+	/* start conversion */
+	writel(0, b + ADCx_HC0);
+
+	/* wait for conversion */
+	ret = wait_for_bit("ADC", b + ADCx_HS, ADCx_HS_C0, ADCx_HS_C0, 10, 0);
+	if (ret)
+		goto adc_exit;
+
+	/* read result */
+	*val = readl(b + ADCx_R0);
+
+adc_exit:
+	if (ret)
+		printf("ADC failure (ret=%i)\n", ret);
+	unmap_physmem(b, MAP_NOCACHE);
+	return ret;
+}
+
+#define VAL_UPPER	2498
+#define VAL_LOWER	1550
+
+static int set_pin_state(void)
+{
+	u32 val;
+	int ret;
+
+	ret = read_adc(&val);
+	if (ret)
+		return ret;
+
+	if (val >= VAL_UPPER)
+		setenv("pin_state", "connected");
+	else if (val < VAL_UPPER && val > VAL_LOWER)
+		setenv("pin_state", "open");
+	else
+		setenv("pin_state", "button");
+
+	return ret;
+}
+
+int board_late_init(void)
+{
+	int ret;
+
+	ret = set_pwm_leds();
+	if (ret)
+		return ret;
+
+	ret = set_pin_state();
+
+	return ret;
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	setup_iomux_usb();
+
+	return 0;
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+	{USDHC4_BASE_ADDR, 0, 8},
+	{USDHC2_BASE_ADDR, 0, 4},
+};
+
+#define USDHC2_CD_GPIO IMX_GPIO_NR(3, 28)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+	if (cfg->esdhc_base == USDHC4_BASE_ADDR)
+		return 1;
+	if (cfg->esdhc_base == USDHC2_BASE_ADDR)
+		return !gpio_get_value(USDHC2_CD_GPIO);
+
+	return -EINVAL;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    USDHC4
+	 * mmc1                    USDHC2
+	 */
+	imx_iomux_v3_setup_multiple_pads(
+		usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+
+	imx_iomux_v3_setup_multiple_pads(
+		usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+	gpio_direction_input(USDHC2_CD_GPIO);
+	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+
+	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+	if (ret) {
+		printf("Warning: failed to initialize USDHC4\n");
+		return ret;
+	}
+
+	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
+	if (ret) {
+		printf("Warning: failed to initialize USDHC2\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_SYS_I2C_MXC
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+#endif
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: VIN|ING 2000\n");
+
+	return 0;
+}
diff --git a/configs/vining_2000_defconfig b/configs/vining_2000_defconfig
new file mode 100644
index 0000000..b1f64f1
--- /dev/null
+++ b/configs/vining_2000_defconfig
@@ -0,0 +1,31 @@ 
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_SAMTEC_VINING_2000=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/samtec/vining_2000/imximage.cfg"
+CONFIG_BOOTDELAY=0
+CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_PCI=y
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
diff --git a/include/configs/vining_2000.h b/include/configs/vining_2000.h
new file mode 100644
index 0000000..235574d
--- /dev/null
+++ b/include/configs/vining_2000.h
@@ -0,0 +1,123 @@ 
+/*
+ * Copyright (C) 2016 samtec automotive software & electronics gmbh
+ *
+ * Configuration settings for the Samtec VIN|ING 2000 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "mx6_common.h"
+
+#ifdef CONFIG_SPL
+#include "imx6_spl.h"
+#endif
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 0) \
+	func(MMC, mmc, 1) \
+	func(USB, usb, 0) \
+	func(PXE, pxe, na) \
+	func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)
+
+#define CONFIG_STACKSIZE		SZ_128K
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* MMC Configuration */
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC4_BASE_ADDR
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED		  100000
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
+
+/* Network */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR          0x0
+
+#define CONFIG_FEC_XCV_TYPE             RMII
+#define CONFIG_ETHPRIME                 "FEC"
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS   0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#endif
+
+#define CONFIG_CMD_PCI
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCIE_IMX
+#define CONFIG_PCIE_IMX_PERST_GPIO	IMX_GPIO_NR(4, 6)
+#endif
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_PWM_IMX
+#define CONFIG_IMX6_PWM_PER_CLK 66000000
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
+#define CONFIG_ENV_SIZE			SZ_8K
+#define CONFIG_ENV_OFFSET_REDUND	(9 * SZ_64K)
+#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
+#define CONFIG_ENV_IS_IN_MMC
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SUPPORT_EMMC_BOOT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_EMMC_RPMB
+#define CONFIG_SYS_MMC_ENV_DEV		0 /* USDHC4 eMMC */
+/* 0=user, 1=boot0, 2=boot1, * 4..7=general0..3. */
+#define CONFIG_SYS_MMC_ENV_PART		1 /* boot0 */
+#endif
+
+#endif				/* __CONFIG_H */