[V2,1/2] pinctrl: tegra: Add DT binding for io pads control

Submitted by Laxman Dewangan on Nov. 9, 2016, 1:06 p.m.

Details

Message ID 1478696782-11657-2-git-send-email-ldewangan@nvidia.com
State New
Headers show

Commit Message

Laxman Dewangan Nov. 9, 2016, 1:06 p.m.
NVIDIA Tegra124 and later SoCs support the multi-voltage level and
low power state of some of its IO pads. The IO pads can work in
the voltage of the 1.8V and 3.3V of IO voltage from IO power rail
sources. When IO interfaces are not used then IO pads can be
configure in low power state to reduce the power consumption from
that IO pads.

On Tegra124, the voltage level of IO power rail source is auto
detected by hardware(SoC) and hence it is only require to configure
in low power mode if IO pads are not used.

On T210 onwards, the auto-detection of voltage level from IO power
rail is removed from SoC and hence SW need to configure the PMC
register explicitly to set proper voltage in IO pads based on
IO rail power source voltage.

Add DT binding document for detailing the DT properties for
configuring IO pads voltage levels and its power state.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>

---
Changes from V1:
 The DT binding document is modified to explain the regulator handle
 for different IOs and how can it be passed from the DT.
---
 .../bindings/pinctrl/nvidia,tegra-io-pad.txt       | 126 +++++++++++++++++++++
 1 file changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt

Comments

Rob Herring Nov. 14, 2016, 7:34 p.m.
On Wed, Nov 09, 2016 at 06:36:21PM +0530, Laxman Dewangan wrote:
> NVIDIA Tegra124 and later SoCs support the multi-voltage level and
> low power state of some of its IO pads. The IO pads can work in
> the voltage of the 1.8V and 3.3V of IO voltage from IO power rail
> sources. When IO interfaces are not used then IO pads can be
> configure in low power state to reduce the power consumption from
> that IO pads.
> 
> On Tegra124, the voltage level of IO power rail source is auto
> detected by hardware(SoC) and hence it is only require to configure
> in low power mode if IO pads are not used.
> 
> On T210 onwards, the auto-detection of voltage level from IO power
> rail is removed from SoC and hence SW need to configure the PMC
> register explicitly to set proper voltage in IO pads based on
> IO rail power source voltage.
> 
> Add DT binding document for detailing the DT properties for
> configuring IO pads voltage levels and its power state.
> 
> Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
> 
> ---
> Changes from V1:
>  The DT binding document is modified to explain the regulator handle
>  for different IOs and how can it be passed from the DT.
> ---
>  .../bindings/pinctrl/nvidia,tegra-io-pad.txt       | 126 +++++++++++++++++++++
>  1 file changed, 126 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt
> new file mode 100644
> index 0000000..6ca961f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt
> @@ -0,0 +1,126 @@
> +NVIDIA Tegra PMC IO pad controller
> +
> +NVIDIA Tegra124 and later SoCs support the multi-voltage level and
> +low power state of some of its IO pads. When IO interface are not
> +used then IO pads can be configure in low power state to reduce
> +the power from that IO pads. The IO pads can work in the voltage
> +of the 1.8V and 3.3V of IO voltage from power rail sources.
> +
> +On Tegra124, the voltage of IO power rail source is auto detected by
> +SoC and hence it is only require to configure in low power mode if
> +IO pads are not used.
> +
> +On T210 onwards, the HW based auto-detection for IO voltage is removed
> +and hence SW need to configure the PMC register explicitly, to set proper
> +voltage in IO pads, based on IO rail power source voltage.
> +
> +The voltage configurations and low power state of IO pads should be done
> +in boot if it is not going to change other wise dynamically based on IO
> +rail voltage on that IO pads and usage of IO pads

s/other wise/otherwise/

The end of the sentence is not clear and missing a period.

> +
> +The DT property of the io pads must be under the node of pmc i.e.
> +pmc@7000e400 for Tegra124 onwards.

s/io/IO/

> +
> +Please refer to <pinctrl-bindings.txt> in this directory for details of the
> +common pinctrl bindings used by client devices, including the meaning of the
> +phrase "pin configuration node".
> +
> +Tegra's pin configuration nodes act as a container for an arbitrary number of
> +subnodes. Each of these subnodes represents some desired configuration for an
> +IO pads, or a list of IO pads. This configuration can include the voltage and
> +power enable/disable control
> +
> +The name of each subnode is not important; all subnodes should be enumerated
> +and processed purely based on their content. Each subnode only affects those
> +parameters that are explicitly listed. Unspecified is represented as an absent
> +property,
> +
> +See the TRM to determine which properties and values apply to each IO pads.
> +
> +Required subnode-properties:
> +==========================
> +- pins : An array of strings. Each string contains the name of an IO pads. Valid
> +	 values for these names are listed below.
> +
> +Optional subnode-properties:
> +==========================
> +Following properties are supported from generic pin configuration explained
> +in <dt-bindings/pinctrl/pinctrl-binding.txt>.
> +low-power-enable:		enable low power mode.
> +low-power-disable:		disable low power mode.
> +
> +Valid values for pin for T124 are:
> +	audio, bb, cam, comp, csia, csib, csie, dsi, dsib, dsic, dsid, hdmi,
> +	hsic, hv, lvds, mipi-bias, nand, pex-bias, pex-clk1, pex-clk2,
> +	pex-ctrl, sdmmc1, sdmmc3, sdmmc4, sys-ddc, uart, usb0, usb1, usb2,
> +	usb-bias
> +
> +Valid values for pin for T210 are:
> +	audio, audio-hv, cam, csia, csib, csic, csid, csie, csif,
> +	dbg, debug-nonao, dmic, dp, dsi, dsib, dsic, dsid, emmc, emmc2,
> +	gpio, hdmi, hsic, lvds, mipi-bias, pex-bias, pex-clk1, pex-clk2,
> +	pex-ctrl, sdmmc1, sdmmc3, spi, spi-hv, uart, usb-bias, usb0,
> +	usb1, usb2, usb3.
> +
> +To find out the IO rail voltage for setting the voltage of IO pad by SW,
> +the regulator supply handle must provided from the DT and it is explained
> +in the regulator DT binding document
> +	<devicetree/bindings/regulator/regulator.txt>.
> +For example, for GPIO rail the supply name is vddio-gpio and regulator
> +handle is supplied from DT as
> +	vddio-gpio-supply = <&regulator_xyz>;
> +
> +For T210, following IO pads support the 1.8V/3.3V and the corresponding
> +io voltage pin names are as follows:
> +	audio -> vddio-audio
> +	audio-hv -> vddio-audio-hv
> +	cam ->vddio-cam
> +	dbg -> vddio-dbg
> +	dmic -> vddio-dmic
> +	gpio -> vddio-gpio
> +	pex-ctrl -> vddio-pex-ctrl
> +	sdmmc1 -> vddio-sdmmc1
> +	sdmmc3 -> vddio-sdmmc3
> +	spi -> vddio-spi
> +	spi-hv -> vddio-spi-hv
> +	uart -> vddio-uart
> +
> +Example:
> +	i2c@7000d000 {
> +		pmic@3c {
> +			regulators {
> +				vddio_sdmmc1: ldo2 {
> +					/* Regulator entries for LDO2 */
> +				};
> +
> +				vdd_cam: ldo3 {
> +					/* Regulator entries for LDO3 */
> +				};
> +			};
> +		};
> +	};
> +
> +	pmc@7000e400 {
> +		vddio-cam = <&vdd_cam>;

Missing -supply.

> +		vddio-sdmmc1-supply = <&vddio_sdmmc1>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&tegra_io_pad_volt_default>;
> +		tegra_io_pad_volt_default: common {
> +			audio-hv {
> +				pins = "audio-hv";
> +				low-power-disable;
> +			};
> +
> +			gpio {
> +				pins = "gpio";
> +				low-power-disable;
> +			};
> +
> +			audio {
> +				pins = "audio", "dmic", "sdmmc3";

What's the purpose of grouping these?

> +				low-power-enable;
> +			};
> +		};
> +
> +	};
> -- 
> 2.1.4
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Laxman Dewangan Nov. 15, 2016, 11:45 a.m.
On Tuesday 15 November 2016 01:04 AM, Rob Herring wrote:
> On Wed, Nov 09, 2016 at 06:36:21PM +0530, Laxman Dewangan wrote:
> +
> +			audio {
> +				pins = "audio", "dmic", "sdmmc3";
> What's the purpose of grouping these?

Just to show that multiple IO pads can be provided here as this is from 
pinctrl dt binding.

--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Jon Hunter Nov. 15, 2016, 6:48 p.m.
On 09/11/16 13:06, Laxman Dewangan wrote:
> NVIDIA Tegra124 and later SoCs support the multi-voltage level and
> low power state of some of its IO pads. The IO pads can work in
> the voltage of the 1.8V and 3.3V of IO voltage from IO power rail
> sources. When IO interfaces are not used then IO pads can be
> configure in low power state to reduce the power consumption from
> that IO pads.
> 
> On Tegra124, the voltage level of IO power rail source is auto
> detected by hardware(SoC) and hence it is only require to configure
> in low power mode if IO pads are not used.
> 
> On T210 onwards, the auto-detection of voltage level from IO power
> rail is removed from SoC and hence SW need to configure the PMC
> register explicitly to set proper voltage in IO pads based on
> IO rail power source voltage.
> 
> Add DT binding document for detailing the DT properties for
> configuring IO pads voltage levels and its power state.
> 
> Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
> 
> ---
> Changes from V1:
>  The DT binding document is modified to explain the regulator handle
>  for different IOs and how can it be passed from the DT.
> ---
>  .../bindings/pinctrl/nvidia,tegra-io-pad.txt       | 126 +++++++++++++++++++++
>  1 file changed, 126 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt
> new file mode 100644
> index 0000000..6ca961f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt
> @@ -0,0 +1,126 @@
> +NVIDIA Tegra PMC IO pad controller
> +
> +NVIDIA Tegra124 and later SoCs support the multi-voltage level and
> +low power state of some of its IO pads. When IO interface are not
> +used then IO pads can be configure in low power state to reduce
> +the power from that IO pads. The IO pads can work in the voltage
> +of the 1.8V and 3.3V of IO voltage from power rail sources.

The last sentence is a bit unclear and does not sound correct. I am not
sure if you are missing the word 'range' somewhere or if you are trying
to say it must be either 1.8V or 3.3V. Looks like you have the same
sentence on the changelog too.

Cheers
Jon
Laxman Dewangan Nov. 21, 2016, 9:16 a.m.
On Wednesday 16 November 2016 12:18 AM, Jon Hunter wrote:
> On 09/11/16 13:06, Laxman Dewangan wrote:
>> +NVIDIA Tegra124 and later SoCs support the multi-voltage level and
>> +low power state of some of its IO pads. When IO interface are not
>> +used then IO pads can be configure in low power state to reduce
>> +the power from that IO pads. The IO pads can work in the voltage
>> +of the 1.8V and 3.3V of IO voltage from power rail sources.
> The last sentence is a bit unclear and does not sound correct. I am not
> sure if you are missing the word 'range' somewhere or if you are trying
> to say it must be either 1.8V or 3.3V. Looks like you have the same
> sentence on the changelog too.
The IO pads are designed to work in two different voltage rail 1.8V 
(nominal) and 3.3V (nominal) for interfacing.
However, the tolerances of the IO pads are:

1.8 V nominal is (1.62V, 1.98V)
3.3 V nominal is (2.97V,3.63V)

--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Patch hide | download patch | download mbox

diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt
new file mode 100644
index 0000000..6ca961f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra-io-pad.txt
@@ -0,0 +1,126 @@ 
+NVIDIA Tegra PMC IO pad controller
+
+NVIDIA Tegra124 and later SoCs support the multi-voltage level and
+low power state of some of its IO pads. When IO interface are not
+used then IO pads can be configure in low power state to reduce
+the power from that IO pads. The IO pads can work in the voltage
+of the 1.8V and 3.3V of IO voltage from power rail sources.
+
+On Tegra124, the voltage of IO power rail source is auto detected by
+SoC and hence it is only require to configure in low power mode if
+IO pads are not used.
+
+On T210 onwards, the HW based auto-detection for IO voltage is removed
+and hence SW need to configure the PMC register explicitly, to set proper
+voltage in IO pads, based on IO rail power source voltage.
+
+The voltage configurations and low power state of IO pads should be done
+in boot if it is not going to change other wise dynamically based on IO
+rail voltage on that IO pads and usage of IO pads
+
+The DT property of the io pads must be under the node of pmc i.e.
+pmc@7000e400 for Tegra124 onwards.
+
+Please refer to <pinctrl-bindings.txt> in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Tegra's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for an
+IO pads, or a list of IO pads. This configuration can include the voltage and
+power enable/disable control
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content. Each subnode only affects those
+parameters that are explicitly listed. Unspecified is represented as an absent
+property,
+
+See the TRM to determine which properties and values apply to each IO pads.
+
+Required subnode-properties:
+==========================
+- pins : An array of strings. Each string contains the name of an IO pads. Valid
+	 values for these names are listed below.
+
+Optional subnode-properties:
+==========================
+Following properties are supported from generic pin configuration explained
+in <dt-bindings/pinctrl/pinctrl-binding.txt>.
+low-power-enable:		enable low power mode.
+low-power-disable:		disable low power mode.
+
+Valid values for pin for T124 are:
+	audio, bb, cam, comp, csia, csib, csie, dsi, dsib, dsic, dsid, hdmi,
+	hsic, hv, lvds, mipi-bias, nand, pex-bias, pex-clk1, pex-clk2,
+	pex-ctrl, sdmmc1, sdmmc3, sdmmc4, sys-ddc, uart, usb0, usb1, usb2,
+	usb-bias
+
+Valid values for pin for T210 are:
+	audio, audio-hv, cam, csia, csib, csic, csid, csie, csif,
+	dbg, debug-nonao, dmic, dp, dsi, dsib, dsic, dsid, emmc, emmc2,
+	gpio, hdmi, hsic, lvds, mipi-bias, pex-bias, pex-clk1, pex-clk2,
+	pex-ctrl, sdmmc1, sdmmc3, spi, spi-hv, uart, usb-bias, usb0,
+	usb1, usb2, usb3.
+
+To find out the IO rail voltage for setting the voltage of IO pad by SW,
+the regulator supply handle must provided from the DT and it is explained
+in the regulator DT binding document
+	<devicetree/bindings/regulator/regulator.txt>.
+For example, for GPIO rail the supply name is vddio-gpio and regulator
+handle is supplied from DT as
+	vddio-gpio-supply = <&regulator_xyz>;
+
+For T210, following IO pads support the 1.8V/3.3V and the corresponding
+io voltage pin names are as follows:
+	audio -> vddio-audio
+	audio-hv -> vddio-audio-hv
+	cam ->vddio-cam
+	dbg -> vddio-dbg
+	dmic -> vddio-dmic
+	gpio -> vddio-gpio
+	pex-ctrl -> vddio-pex-ctrl
+	sdmmc1 -> vddio-sdmmc1
+	sdmmc3 -> vddio-sdmmc3
+	spi -> vddio-spi
+	spi-hv -> vddio-spi-hv
+	uart -> vddio-uart
+
+Example:
+	i2c@7000d000 {
+		pmic@3c {
+			regulators {
+				vddio_sdmmc1: ldo2 {
+					/* Regulator entries for LDO2 */
+				};
+
+				vdd_cam: ldo3 {
+					/* Regulator entries for LDO3 */
+				};
+			};
+		};
+	};
+
+	pmc@7000e400 {
+		vddio-cam = <&vdd_cam>;
+		vddio-sdmmc1-supply = <&vddio_sdmmc1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tegra_io_pad_volt_default>;
+		tegra_io_pad_volt_default: common {
+			audio-hv {
+				pins = "audio-hv";
+				low-power-disable;
+			};
+
+			gpio {
+				pins = "gpio";
+				low-power-disable;
+			};
+
+			audio {
+				pins = "audio", "dmic", "sdmmc3";
+				low-power-enable;
+			};
+		};
+
+	};