@@ -26,3 +26,5 @@ connected flash properties
select (n_ss_out).
- tslch-ns : Delay in master reference clocks between setting
n_ss_out low and first bit transfer
+- sample-edge-rising : Data outputs from flash memory will be sampled on the
+ rising edge. Default is falling edge.
@@ -39,8 +39,10 @@ static int cadence_spi_write_speed(struct udevice *bus, uint hz)
/* Calibration sequence to determine the read data capture delay register */
static int spi_calibration(struct udevice *bus, uint hz)
{
+ struct cadence_spi_platdata *plat = bus->platdata;
struct cadence_spi_priv *priv = dev_get_priv(bus);
void *base = priv->regbase;
+ bool edge = plat->sample_edge_rising;
u8 opcode_rdid = 0x9F;
unsigned int idcode = 0, temp = 0;
int err = 0, i, range_lo = -1, range_hi = -1;
@@ -49,7 +51,7 @@ static int spi_calibration(struct udevice *bus, uint hz)
cadence_spi_write_speed(bus, 1000000);
/* configure the read data capture delay register to 0 */
- cadence_qspi_apb_readdata_capture(base, 1, 0);
+ cadence_qspi_apb_readdata_capture(base, true, edge, 0);
/* Enable QSPI */
cadence_qspi_apb_controller_enable(base);
@@ -69,7 +71,7 @@ static int spi_calibration(struct udevice *bus, uint hz)
cadence_qspi_apb_controller_disable(base);
/* reconfigure the read data capture delay register */
- cadence_qspi_apb_readdata_capture(base, 1, i);
+ cadence_qspi_apb_readdata_capture(base, true, edge, i);
/* Enable back QSPI */
cadence_qspi_apb_controller_enable(base);
@@ -105,7 +107,8 @@ static int spi_calibration(struct udevice *bus, uint hz)
cadence_qspi_apb_controller_disable(base);
/* configure the final value for read data capture delay register */
- cadence_qspi_apb_readdata_capture(base, 1, (range_hi + range_lo) / 2);
+ cadence_qspi_apb_readdata_capture(base, true, edge,
+ (range_hi + range_lo) / 2);
debug("SF: Read data capture delay calibrated to %i (%i - %i)\n",
(range_hi + range_lo) / 2, range_lo, range_hi);
@@ -298,6 +301,7 @@ static int cadence_spi_ofdata_to_platdata(struct udevice *bus)
plat->regbase = (void *)data[0];
plat->ahbbase = (void *)data[2];
+ plat->sram_size = fdtdec_get_int(blob, node, "sram-size", 128);
/* All other paramters are embedded in the child node */
subnode = fdt_first_subnode(blob, node);
@@ -317,7 +321,8 @@ static int cadence_spi_ofdata_to_platdata(struct udevice *bus)
plat->tsd2d_ns = fdtdec_get_int(blob, subnode, "tsd2d-ns", 255);
plat->tchsh_ns = fdtdec_get_int(blob, subnode, "tchsh-ns", 20);
plat->tslch_ns = fdtdec_get_int(blob, subnode, "tslch-ns", 20);
- plat->sram_size = fdtdec_get_int(blob, node, "sram-size", 128);
+ plat->sample_edge_rising = fdtdec_get_bool(blob, subnode,
+ "sample-edge-rising");
debug("%s: regbase=%p ahbbase=%p max-frequency=%d page-size=%d\n",
__func__, plat->regbase, plat->ahbbase, plat->max_hz,
@@ -26,6 +26,7 @@ struct cadence_spi_platdata {
u32 tchsh_ns;
u32 tslch_ns;
u32 sram_size;
+ bool sample_edge_rising;
};
struct cadence_spi_priv {
@@ -73,6 +74,6 @@ void cadence_qspi_apb_delay(void *reg_base,
unsigned int tchsh_ns, unsigned int tslch_ns);
void cadence_qspi_apb_enter_xip(void *reg_base, char xip_dummy);
void cadence_qspi_apb_readdata_capture(void *reg_base,
- unsigned int bypass, unsigned int delay);
+ bool bypass, bool edge, unsigned int delay);
#endif /* __CADENCE_QSPI_H__ */
@@ -98,6 +98,7 @@
#define CQSPI_REG_RD_DATA_CAPTURE_BYPASS BIT(0)
#define CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB 1
#define CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK 0xF
+#define CQSPI_REG_RD_DATA_CAPTURE_EDGE BIT(5)
#define CQSPI_REG_SIZE 0x14
#define CQSPI_REG_SIZE_ADDRESS_LSB 0
@@ -237,7 +238,7 @@ static unsigned int cadence_qspi_wait_idle(void *reg_base)
}
void cadence_qspi_apb_readdata_capture(void *reg_base,
- unsigned int bypass, unsigned int delay)
+ bool bypass, bool edge, unsigned int delay)
{
unsigned int reg;
cadence_qspi_apb_controller_disable(reg_base);
@@ -249,6 +250,11 @@ void cadence_qspi_apb_readdata_capture(void *reg_base,
else
reg &= ~CQSPI_REG_RD_DATA_CAPTURE_BYPASS;
+ if (edge)
+ reg |= CQSPI_REG_RD_DATA_CAPTURE_EDGE;
+ else
+ reg &= ~CQSPI_REG_RD_DATA_CAPTURE_EDGE;
+
reg &= ~(CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK
<< CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB);
Whilst at it, move the code to read the "sram-size" property into the other code that reads properties from the node, rather than the SF subnode. Also change the code to use a bool for the bypass arg. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> --- v2: Change name of DT prop and provide details of what it does. Whilst at it, move the code to read the "sram-size" property into the other code that reads properties from the node, rather than the SF subnode. Also changed the code to use a bool for the bypass arg. Note: I didn't explicitly state that the prop is optional as all of the props listed in that section are optional. --- doc/device-tree-bindings/spi/spi-cadence.txt | 2 ++ drivers/spi/cadence_qspi.c | 13 +++++++++---- drivers/spi/cadence_qspi.h | 3 ++- drivers/spi/cadence_qspi_apb.c | 8 +++++++- 4 files changed, 20 insertions(+), 6 deletions(-)