diff mbox

[v8] net: emac: emac gigabit ethernet controller driver

Message ID 1470951245-13665-1-git-send-email-timur@codeaurora.org
State Changes Requested, archived
Delegated to: David Miller
Headers show

Commit Message

Timur Tabi Aug. 11, 2016, 9:34 p.m. UTC
Add supports for ethernet controller HW on Qualcomm Technologies, Inc. SoC.
This driver supports the following features:
1) Checksum offload.
2) Interrupt coalescing support.
3) SGMII phy.
4) phylib interface for external phy

Based on original work by
	Niranjana Vishwanathapura <nvishwan@codeaurora.org>
	Gilad Avidov <gavidov@codeaurora.org>

Signed-off-by: Timur Tabi <timur@codeaurora.org>
---

v8:
 - Remove "phy-version" property, use different compatible strings to
   differentiate EMAC versions instead.
 - fully unmap all DMA mappings upon any single DMA mapping error
 - add support for 32-bit DMA masks
 - Make reads/writes to hardware data structures endian-safe
 - emac_mac_stop already disables interrupts, so don't do it in emac_mac_reset
 - Set adpt->rxbuf_size only when initializing the MAC, not when changing MTU
 - Fix the calculation of the # of free descriptors required
 - Always stop the PHY before disconnecting it
 - Miscellaneous cleanups (removing unused definitions, fix typos and spacing,
   use unsized ints, etc).

v7:
 - add "phy-version" to DT docs
 - remove emac_status_bits, use mutexes instead of polling a status bit
 - test return code from dma_map_single() calls
 - use __netdev_alloc_skb_ip_align instead of dev_alloc_skb
 - add a missing free_irq on an error path
 - return an error code from emac_reinit_locked
 - support setting the MTU even when the interface is down
 - use a spinlock not a mutex in emac_get_stats64
 - don't redundantly set the ethernet device name
 - remove all hardware timestamp code, since it's incomplete
 - remove redundant 'reset' param to emac_mac_down()
 - handle queue throttling properly

v6:
 - Properly ordered local variables
 - use built-in GEN_MASK instead of BITS_MASK
 - remove redundant call to emac_rx_mode_set from emac_mac_up
 - removed emac_rfd structure, use dma_addr_t directly instead
 - removed emac_mac_speed enun, replaced with macros
 - removed superfluous phy_stop from emac_mac_down(), which prevented reloading module
 - add missing netif_napi_del
 - set the DMA mask

v5:
 - changed author to Timur, added MAINTAINERS entry
 - use phylib, replacing internal phy code
 - added support for EMAC internal SGMII v2
 - fix ~DIS_INT warning
 - update DT bindings, including removing unused properties
 - removed interrupt handler for internal sgmii
 - removed link status check handler/state (replaced with phylib)
 - removed periodic timer handler (replaced with phylib)
 - removed power management code (will be rewritten later)
 - external phy is now required, not optional
 - removed redundant EMAC_STATUS_DOWN status flag
 - removed redundant link status and speed variables
 - removed redundant status bits (vlan strip, promiscuous, loopback, etc)
 - removed useless watchdog status
 - removed command-line parameters
 - cleaned up probe messages
 - removed redundant params from emac_sgmii_link_init()
 - always call netdev_completed_queue() (per review comment)
 - fix emac_napi_rtx() (per review comment)
 - removed max_ints loop in interrupt handler
 - removed redundant mutex around phy read/write calls
 - added lock for reading emac status (per review comment)
 - generate random MAC address if it can't be read from firmware
 - replace EMAC_DMA_ADDR_HI/LO with upper/lower_32_bits
 - don't test return value from platform_get_resource (per review comment)
 - use net_warn_ratelimited (per review comment)
 - don't set the dma masks (will be set by DT or IORT code)
 - remove unused emac_tx_tpd_ts_save()
 - removed redundant local MTU variable

v4:
 - add missing ipv6 header file
 - correct compatible string
 - fix spacing in emac_reg_write arrays
 - drop unnecessary cell-index property
 - remove unsupported DT properties from docs
 - remove GPIO initialization and update docs

v3:
 - remove most of the memory barriers by using the non xxx_relaxed() api.
 - remove RSS and WOL support.
 - correct comments from physical address to dma address.
 - rearrange structs to make them packed.
 - replace polling loops with readl_poll_timeout().
 - remove unnecessary wrapper functions from phy layer.
 - add blank line before return statements.
 - set to null clocks after clk_put().
 - use module_platform_driver() and dma_set_mask_and_coherent()
 - replace long hex bitmasks with BIT() macro.

v2:
 - replace hw bit fields to macros with bitwise operations.
 - change all iterators to unsized types (int)
 - some minor code flow improvements.
 - change return type to void for functions which return value is never
   used.
 - replace instance of xxxxl_relaxed() io followed by mb() with a
   readl()/writel().

 .../devicetree/bindings/net/qcom-emac.txt          |   64 +
 MAINTAINERS                                        |    6 +
 drivers/net/ethernet/qualcomm/Kconfig              |   11 +
 drivers/net/ethernet/qualcomm/Makefile             |    2 +
 drivers/net/ethernet/qualcomm/emac/Makefile        |    7 +
 drivers/net/ethernet/qualcomm/emac/emac-mac.c      | 1532 ++++++++++++++++++++
 drivers/net/ethernet/qualcomm/emac/emac-mac.h      |  250 ++++
 drivers/net/ethernet/qualcomm/emac/emac-phy.c      |  201 +++
 drivers/net/ethernet/qualcomm/emac/emac-phy.h      |   32 +
 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c    |  693 +++++++++
 drivers/net/ethernet/qualcomm/emac/emac-sgmii.h    |   24 +
 drivers/net/ethernet/qualcomm/emac/emac.c          |  796 ++++++++++
 drivers/net/ethernet/qualcomm/emac/emac.h          |  335 +++++
 13 files changed, 3953 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/qcom-emac.txt
 create mode 100644 drivers/net/ethernet/qualcomm/emac/Makefile
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.c
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.h
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.c
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.h
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.c
 create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.h

Comments

Florian Fainelli Aug. 11, 2016, 10:45 p.m. UTC | #1
On 08/11/2016 02:34 PM, Timur Tabi wrote:
> Add supports for ethernet controller HW on Qualcomm Technologies, Inc. SoC.
> This driver supports the following features:
> 1) Checksum offload.
> 2) Interrupt coalescing support.
> 3) SGMII phy.
> 4) phylib interface for external phy

OK, so this is looking good now, just a few nits, feel free to submit as
clean up patches, would this one be accepted.

[snip]

> +Example:
> +soc {
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +	dma-ranges = <0 0 0xffffffff>;
> +
> +	emac0: ethernet@feb20000 {
> +		compatible = "qcom,fsm9900-emac";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		reg-names = "base", "csr", "ptp", "sgmii";
> +		reg =   <0xfeb20000 0x10000>,
> +			<0xfeb36000 0x1000>,
> +			<0xfeb3c000 0x4000>,
> +			<0xfeb38000 0x400>;
> +		interrupt-parent = <&emac0>;
> +		#interrupt-cells = <1>;
> +		interrupts = <76 80>;
> +		interrupt-names = "emac_core0", "sgmii_irq";
> +		phy0: ethernet-phy@0 {
> +			compatible = "qcom,fsm9900-emac-phy";
> +			reg = <0>;
> +		}

If this is an external PHY, the expectation is that it will be hanging
off a MDIO bus controller, either the MDIO bus internal to the MAC, or
an external MDIO bus (separate register range).

If such a PHY node is provided, the expectation is that your Ethernet
MAC will have a phy-handle property and a phy-mode property to specify
how to connect to this external PHY, so in your specific case, better
remove the PHY from your example, or detail further how it should be done.

> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&mdio_pins_a>;
> +	};
> +
> +	tlmm: pinctrl@fd510000 {
> +		compatible = "qcom,fsm9900-pinctrl";
> +
> +		mdio_pins_a: mdio {
> +			state {
> +				pins = "gpio123", "gpio124";
> +				function = "mdio";
> +			};
> +		};
> +	};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 952fd2a..38dabdf 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -9404,6 +9404,12 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
>  S:	Supported
>  F:	drivers/net/wireless/ath/ath10k/
>  
> +QUALCOMM EMAC GIGABIT ETHERNET DRIVER
> +M:	Timur Tabi <timur@codeaurora.org>
> +L:	netdev@vger.kernel.org
> +S:	Supported
> +F:	drivers/net/ethernet/qualcomm/emac/
> +
>  QUALCOMM HEXAGON ARCHITECTURE
>  M:	Richard Kuo <rkuo@codeaurora.org>
>  L:	linux-hexagon@vger.kernel.org
> diff --git a/drivers/net/ethernet/qualcomm/Kconfig b/drivers/net/ethernet/qualcomm/Kconfig
> index a76e380..85b599f 100644
> --- a/drivers/net/ethernet/qualcomm/Kconfig
> +++ b/drivers/net/ethernet/qualcomm/Kconfig
> @@ -24,4 +24,15 @@ config QCA7000
>  	  To compile this driver as a module, choose M here. The module
>  	  will be called qcaspi.
>  
> +config QCOM_EMAC
> +	tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
> +	select CRC32

select PHYLIB?

> +	---help---
> +	  This driver supports the Qualcomm Technologies, Inc. Gigabit
> +	  Ethernet Media Access Controller (EMAC). The controller
> +	  supports IEEE 802.3-2002, half-duplex mode at 10/100 Mb/s,
> +	  full-duplex mode at 10/100/1000Mb/s, Wake On LAN (WOL) for
> +	  low power, Receive-Side Scaling (RSS), and IEEE 1588-2008
> +	  Precision Clock Synchronization Protocol.
> +
>  endif # NET_VENDOR_QUALCOMM
> diff --git a/drivers/net/ethernet/qualcomm/Makefile b/drivers/net/ethernet/qualcomm/Makefile
> index 9da2d75..1b3a0ce 100644
> --- a/drivers/net/ethernet/qualcomm/Makefile
> +++ b/drivers/net/ethernet/qualcomm/Makefile
> @@ -4,3 +4,5 @@
>  
>  obj-$(CONFIG_QCA7000) += qcaspi.o
>  qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o
> +
> +obj-$(CONFIG_QCOM_EMAC) += emac/

Since you have a check on CONFIG_QCOM_EMAC in emac/Makefile, you could
always recurse into that directory while building (use obj-y).

> diff --git a/drivers/net/ethernet/qualcomm/emac/Makefile b/drivers/net/ethernet/qualcomm/emac/Makefile
> new file mode 100644
> index 0000000..01ee144
> --- /dev/null
> +++ b/drivers/net/ethernet/qualcomm/emac/Makefile
> @@ -0,0 +1,7 @@
> +#
> +# Makefile for the Qualcomm Technologies, Inc. EMAC Gigabit Ethernet driver
> +#
> +
> +obj-$(CONFIG_QCOM_EMAC) += qcom-emac.o

[snip]

> +
> +static void emac_adjust_link(struct net_device *netdev)
> +{
> +	struct emac_adapter *adpt = netdev_priv(netdev);
> +	struct phy_device *phydev = netdev->phydev;
> +
> +	if (phydev->link)
> +		emac_mac_start(adpt);
> +	else
> +		emac_mac_stop(adpt);

This is really excessive here, you typically don't need to completely
stop your transmitter/receiver/DMA/what have you, just reprogram the MAC
with the appropriate link speed/duplex/pause parameters.
Rob Herring Aug. 12, 2016, 6:55 p.m. UTC | #2
On Thu, Aug 11, 2016 at 04:34:05PM -0500, Timur Tabi wrote:
> Add supports for ethernet controller HW on Qualcomm Technologies, Inc. SoC.
> This driver supports the following features:
> 1) Checksum offload.
> 2) Interrupt coalescing support.
> 3) SGMII phy.
> 4) phylib interface for external phy
> 
> Based on original work by
> 	Niranjana Vishwanathapura <nvishwan@codeaurora.org>
> 	Gilad Avidov <gavidov@codeaurora.org>
> 
> Signed-off-by: Timur Tabi <timur@codeaurora.org>
> ---
> 
> v8:
>  - Remove "phy-version" property, use different compatible strings to
>    differentiate EMAC versions instead.
>  - fully unmap all DMA mappings upon any single DMA mapping error
>  - add support for 32-bit DMA masks
>  - Make reads/writes to hardware data structures endian-safe
>  - emac_mac_stop already disables interrupts, so don't do it in emac_mac_reset
>  - Set adpt->rxbuf_size only when initializing the MAC, not when changing MTU
>  - Fix the calculation of the # of free descriptors required
>  - Always stop the PHY before disconnecting it
>  - Miscellaneous cleanups (removing unused definitions, fix typos and spacing,
>    use unsized ints, etc).
> 
> v7:
>  - add "phy-version" to DT docs
>  - remove emac_status_bits, use mutexes instead of polling a status bit
>  - test return code from dma_map_single() calls
>  - use __netdev_alloc_skb_ip_align instead of dev_alloc_skb
>  - add a missing free_irq on an error path
>  - return an error code from emac_reinit_locked
>  - support setting the MTU even when the interface is down
>  - use a spinlock not a mutex in emac_get_stats64
>  - don't redundantly set the ethernet device name
>  - remove all hardware timestamp code, since it's incomplete
>  - remove redundant 'reset' param to emac_mac_down()
>  - handle queue throttling properly
> 
> v6:
>  - Properly ordered local variables
>  - use built-in GEN_MASK instead of BITS_MASK
>  - remove redundant call to emac_rx_mode_set from emac_mac_up
>  - removed emac_rfd structure, use dma_addr_t directly instead
>  - removed emac_mac_speed enun, replaced with macros
>  - removed superfluous phy_stop from emac_mac_down(), which prevented reloading module
>  - add missing netif_napi_del
>  - set the DMA mask
> 
> v5:
>  - changed author to Timur, added MAINTAINERS entry
>  - use phylib, replacing internal phy code
>  - added support for EMAC internal SGMII v2
>  - fix ~DIS_INT warning
>  - update DT bindings, including removing unused properties
>  - removed interrupt handler for internal sgmii
>  - removed link status check handler/state (replaced with phylib)
>  - removed periodic timer handler (replaced with phylib)
>  - removed power management code (will be rewritten later)
>  - external phy is now required, not optional
>  - removed redundant EMAC_STATUS_DOWN status flag
>  - removed redundant link status and speed variables
>  - removed redundant status bits (vlan strip, promiscuous, loopback, etc)
>  - removed useless watchdog status
>  - removed command-line parameters
>  - cleaned up probe messages
>  - removed redundant params from emac_sgmii_link_init()
>  - always call netdev_completed_queue() (per review comment)
>  - fix emac_napi_rtx() (per review comment)
>  - removed max_ints loop in interrupt handler
>  - removed redundant mutex around phy read/write calls
>  - added lock for reading emac status (per review comment)
>  - generate random MAC address if it can't be read from firmware
>  - replace EMAC_DMA_ADDR_HI/LO with upper/lower_32_bits
>  - don't test return value from platform_get_resource (per review comment)
>  - use net_warn_ratelimited (per review comment)
>  - don't set the dma masks (will be set by DT or IORT code)
>  - remove unused emac_tx_tpd_ts_save()
>  - removed redundant local MTU variable
> 
> v4:
>  - add missing ipv6 header file
>  - correct compatible string
>  - fix spacing in emac_reg_write arrays
>  - drop unnecessary cell-index property
>  - remove unsupported DT properties from docs
>  - remove GPIO initialization and update docs
> 
> v3:
>  - remove most of the memory barriers by using the non xxx_relaxed() api.
>  - remove RSS and WOL support.
>  - correct comments from physical address to dma address.
>  - rearrange structs to make them packed.
>  - replace polling loops with readl_poll_timeout().
>  - remove unnecessary wrapper functions from phy layer.
>  - add blank line before return statements.
>  - set to null clocks after clk_put().
>  - use module_platform_driver() and dma_set_mask_and_coherent()
>  - replace long hex bitmasks with BIT() macro.
> 
> v2:
>  - replace hw bit fields to macros with bitwise operations.
>  - change all iterators to unsized types (int)
>  - some minor code flow improvements.
>  - change return type to void for functions which return value is never
>    used.
>  - replace instance of xxxxl_relaxed() io followed by mb() with a
>    readl()/writel().
> 
>  .../devicetree/bindings/net/qcom-emac.txt          |   64 +

Acked-by: Rob Herring <robh@kernel.org>

>  MAINTAINERS                                        |    6 +
>  drivers/net/ethernet/qualcomm/Kconfig              |   11 +
>  drivers/net/ethernet/qualcomm/Makefile             |    2 +
>  drivers/net/ethernet/qualcomm/emac/Makefile        |    7 +
>  drivers/net/ethernet/qualcomm/emac/emac-mac.c      | 1532 ++++++++++++++++++++
>  drivers/net/ethernet/qualcomm/emac/emac-mac.h      |  250 ++++
>  drivers/net/ethernet/qualcomm/emac/emac-phy.c      |  201 +++
>  drivers/net/ethernet/qualcomm/emac/emac-phy.h      |   32 +
>  drivers/net/ethernet/qualcomm/emac/emac-sgmii.c    |  693 +++++++++
>  drivers/net/ethernet/qualcomm/emac/emac-sgmii.h    |   24 +
>  drivers/net/ethernet/qualcomm/emac/emac.c          |  796 ++++++++++
>  drivers/net/ethernet/qualcomm/emac/emac.h          |  335 +++++
>  13 files changed, 3953 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/qcom-emac.txt
>  create mode 100644 drivers/net/ethernet/qualcomm/emac/Makefile
>  create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.c
>  create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-mac.h
>  create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.c
>  create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-phy.h
>  create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
>  create mode 100644 drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
>  create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.c
>  create mode 100644 drivers/net/ethernet/qualcomm/emac/emac.h
Lino Sanfilippo Aug. 12, 2016, 8:22 p.m. UTC | #3
Hi,

I really dont want to be a killjoy, but...

> +		int ret;
> +
> +		skb = __netdev_alloc_skb_ip_align(adpt->netdev,
> +						  adpt->rxbuf_size, GFP_KERNEL);

This is also called in softirq context by the napi handler in which GFP_KERNEL is
not allowed.
You can either extend the refill function by one gfp_t parameter and then call it 
with GFP_KERNEL for the initial rx buffer allocation when the hw is brought up and 
then with GFP_ATOMIC for refilling in the NAPI handler. Or simply always use GFP_ATOMIC.
In the latter case the additional parameter is not needed of course and you can
use netdev_alloc_skb_ip_align() instead of __netdev_alloc_skb_ip_align().

Regards,
Lino
Timur Tabi Aug. 12, 2016, 8:39 p.m. UTC | #4
Lino Sanfilippo wrote:
> You can either extend the refill function by one gfp_t parameter and then call it
> with GFP_KERNEL for the initial rx buffer allocation when the hw is brought up and
> then with GFP_ATOMIC for refilling in the NAPI handler. Or simply always use GFP_ATOMIC.
> In the latter case the additional parameter is not needed of course and you can
> use netdev_alloc_skb_ip_align() instead of __netdev_alloc_skb_ip_align().

I will change this to use netdev_alloc_skb_ip_align().

Thanks.
Timur Tabi Aug. 17, 2016, 7:38 p.m. UTC | #5
Florian Fainelli wrote:
> On 08/11/2016 02:34 PM, Timur Tabi wrote:
>> >Add supports for ethernet controller HW on Qualcomm Technologies, Inc. SoC.
>> >This driver supports the following features:
>> >1) Checksum offload.
>> >2) Interrupt coalescing support.
>> >3) SGMII phy.
>> >4) phylib interface for external phy

> OK, so this is looking good now, just a few nits, feel free to submit as
> clean up patches, would this one be accepted.

I will post a v9.

>> >+soc {
>> >+	#address-cells = <1>;
>> >+	#size-cells = <1>;
>> >+	dma-ranges = <0 0 0xffffffff>;
>> >+
>> >+	emac0: ethernet@feb20000 {
>> >+		compatible = "qcom,fsm9900-emac";
>> >+		#address-cells = <1>;
>> >+		#size-cells = <1>;
>> >+		reg-names = "base", "csr", "ptp", "sgmii";
>> >+		reg =   <0xfeb20000 0x10000>,
>> >+			<0xfeb36000 0x1000>,
>> >+			<0xfeb3c000 0x4000>,
>> >+			<0xfeb38000 0x400>;
>> >+		interrupt-parent = <&emac0>;
>> >+		#interrupt-cells = <1>;
>> >+		interrupts = <76 80>;
>> >+		interrupt-names = "emac_core0", "sgmii_irq";
>> >+		phy0: ethernet-phy@0 {
>> >+			compatible = "qcom,fsm9900-emac-phy";
>> >+			reg = <0>;
>> >+		}

> If this is an external PHY, the expectation is that it will be hanging
> off a MDIO bus controller, either the MDIO bus internal to the MAC, or
> an external MDIO bus (separate register range).

So for starters, I forgot to delete the 'compatible' property from this 
document.  Its presence breaks of_mdiobus_child_is_phy().

> If such a PHY node is provided, the expectation is that your Ethernet
> MAC will have a phy-handle property and a phy-mode property to specify
> how to connect to this external PHY, so in your specific case, better
> remove the PHY from your example, or detail further how it should be done.

Something is odd about of_mdiobus_register().

This function scans child nodes to look for PHYs:

/* Loop over the child nodes and register a phy_device for each phy */
for_each_available_child_of_node(np, child) {
	addr = of_mdio_parse_addr(&mdio->dev, child);

And in my driver, this works.  However, later when I try to call 
of_phy_find_device(), it fails.  That's because of_phy_find_device() 
wants the np of the child node.  But the only way to get that is with a 
phy-phandle property which I need to manually parse.

So what's the point of having of_mdiobus_register() parse child nodes, 
if you need a phy-phandle pointer anyway?

>> >diff --git a/drivers/net/ethernet/qualcomm/Kconfig b/drivers/net/ethernet/qualcomm/Kconfig
>> >index a76e380..85b599f 100644
>> >--- a/drivers/net/ethernet/qualcomm/Kconfig
>> >+++ b/drivers/net/ethernet/qualcomm/Kconfig
>> >@@ -24,4 +24,15 @@ config QCA7000
>> >  	  To compile this driver as a module, choose M here. The module
>> >  	  will be called qcaspi.
>> >
>> >+config QCOM_EMAC
>> >+	tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
>> >+	select CRC32

> select PHYLIB?

Ok.

>> >diff --git a/drivers/net/ethernet/qualcomm/Makefile b/drivers/net/ethernet/qualcomm/Makefile
>> >index 9da2d75..1b3a0ce 100644
>> >--- a/drivers/net/ethernet/qualcomm/Makefile
>> >+++ b/drivers/net/ethernet/qualcomm/Makefile
>> >@@ -4,3 +4,5 @@
>> >
>> >  obj-$(CONFIG_QCA7000) += qcaspi.o
>> >  qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o
>> >+
>> >+obj-$(CONFIG_QCOM_EMAC) += emac/

> Since you have a check on CONFIG_QCOM_EMAC in emac/Makefile, you could
> always recurse into that directory while building (use obj-y).

Obviously, having "obj-$(CONFIG_QCOM_EMAC)" in both Makefiles is 
redundant, but wouldn't it make more sense to change 
"obj-$(CONFIG_QCOM_EMAC)" to "obj-y" in 
drivers/net/ethernet/qualcomm/emac/Makefile, so that I only recurse if 
necessary?

>> >+static void emac_adjust_link(struct net_device *netdev)
>> >+{
>> >+	struct emac_adapter *adpt = netdev_priv(netdev);
>> >+	struct phy_device *phydev = netdev->phydev;
>> >+
>> >+	if (phydev->link)
>> >+		emac_mac_start(adpt);
>> >+	else
>> >+		emac_mac_stop(adpt);

> This is really excessive here, you typically don't need to completely
> stop your transmitter/receiver/DMA/what have you, just reprogram the MAC
> with the appropriate link speed/duplex/pause parameters.

Yes, I realize that a lot of the reinit code in my driver is "heavy", 
and that it could be optimized for specific situations.  However, I'd 
like to save that for another patch, because it would require me to 
study the documentation and do extensive tests.

I can't tell you today whether emac_mac_start() is overkill for the 
specific link change.  For all I know, the hardware does require the TX 
to stop before changing the link speed.  Remember, the EMAC does have a 
weird double-phy (one internal, one external).
Florian Fainelli Aug. 17, 2016, 8:03 p.m. UTC | #6
On 08/17/2016 12:38 PM, Timur Tabi wrote:
>> If this is an external PHY, the expectation is that it will be hanging
>> off a MDIO bus controller, either the MDIO bus internal to the MAC, or
>> an external MDIO bus (separate register range).
> 
> So for starters, I forgot to delete the 'compatible' property from this
> document.  Its presence breaks of_mdiobus_child_is_phy().

The MDIO devices and Ethernet PHY binding should certainly be improved,
but the bulk of it is either you use ethernet-phy-ieee802.3-c22 or
ethernet-phy-ieee802.3-c45, or nothing. Else, the MDIO bus probing code
just assumes it can match a MDIO device (not specifically an Ethernet
PHY) with its compatible string.

> 
>> If such a PHY node is provided, the expectation is that your Ethernet
>> MAC will have a phy-handle property and a phy-mode property to specify
>> how to connect to this external PHY, so in your specific case, better
>> remove the PHY from your example, or detail further how it should be
>> done.
> 
> Something is odd about of_mdiobus_register().
> 
> This function scans child nodes to look for PHYs:
> 
> /* Loop over the child nodes and register a phy_device for each phy */
> for_each_available_child_of_node(np, child) {
>     addr = of_mdio_parse_addr(&mdio->dev, child);
> 
> And in my driver, this works.  However, later when I try to call
> of_phy_find_device(), it fails.  That's because of_phy_find_device()
> wants the np of the child node.  But the only way to get that is with a
> phy-phandle property which I need to manually parse.

of_get_phandle() should return the device_node pointer associated with
the phy-handle property which you can later use and pass to
of_phy_find_device(). There are plenty of examples in the tree and the
logic is almost always the same.

> 
> So what's the point of having of_mdiobus_register() parse child nodes,
> if you need a phy-phandle pointer anyway?

Not all MDIO devices are Ethernet PHYs, some of them are Ethernet
switches, or any other PHY (USB, PCIE, SATA) just sitting on the same
MDIO bus HW instance so you need to create device_node and struct device
instances for these deviecs listed in the Device Tree since the bus is
self-discoverable (like I2C).

Your Ethernet controller somehow needs to know which Ethernet PHY it is
attached to since the location of the Ethernet PHY on the bus could
change from design to design, let alone the actual topology (you could
have a GPIO bit-banged MDIO bus or something else).

>> Since you have a check on CONFIG_QCOM_EMAC in emac/Makefile, you could
>> always recurse into that directory while building (use obj-y).
> 
> Obviously, having "obj-$(CONFIG_QCOM_EMAC)" in both Makefiles is
> redundant, but wouldn't it make more sense to change
> "obj-$(CONFIG_QCOM_EMAC)" to "obj-y" in
> drivers/net/ethernet/qualcomm/emac/Makefile, so that I only recurse if
> necessary?

Whichever makes the most sense, when there is a directory involved, my
preference is to always recurse in that directory and selectively
compile from there, since the Kconfig/Makefile options are all located
within the same hierarchical level, just a preference.

> 
>>> >+static void emac_adjust_link(struct net_device *netdev)
>>> >+{
>>> >+    struct emac_adapter *adpt = netdev_priv(netdev);
>>> >+    struct phy_device *phydev = netdev->phydev;
>>> >+
>>> >+    if (phydev->link)
>>> >+        emac_mac_start(adpt);
>>> >+    else
>>> >+        emac_mac_stop(adpt);
> 
>> This is really excessive here, you typically don't need to completely
>> stop your transmitter/receiver/DMA/what have you, just reprogram the MAC
>> with the appropriate link speed/duplex/pause parameters.
> 
> Yes, I realize that a lot of the reinit code in my driver is "heavy",
> and that it could be optimized for specific situations.  However, I'd
> like to save that for another patch, because it would require me to
> study the documentation and do extensive tests.
> 
> I can't tell you today whether emac_mac_start() is overkill for the
> specific link change.  For all I know, the hardware does require the TX
> to stop before changing the link speed.  Remember, the EMAC does have a
> weird double-phy (one internal, one external).

Fair enough, not having to stop the TX from the SW perspective should be
kind of basic requirement here, most drivers/HW don't seem to require
that, because even if packets were inflight at the time the link went
down, the MAC should sense the carrier loss and report that accordingly.
Now there could be many different ways to implement and screw that up,
so yes, future patch seems like a good approach.
Andrew Lunn Aug. 17, 2016, 8:05 p.m. UTC | #7
> Something is odd about of_mdiobus_register().
> 
> This function scans child nodes to look for PHYs:
> 
> /* Loop over the child nodes and register a phy_device for each phy */
> for_each_available_child_of_node(np, child) {
> 	addr = of_mdio_parse_addr(&mdio->dev, child);
> 
> And in my driver, this works.  However, later when I try to call
> of_phy_find_device(), it fails.  That's because of_phy_find_device()
> wants the np of the child node.  But the only way to get that is
> with a phy-phandle property which I need to manually parse.

You do need the phy-handle, because you can have multiple PHYs, and
ethernet switches on the MDIO bus. You need to indicate which of those
PHYs is connected to this MAC.

> So what's the point of having of_mdiobus_register() parse child
> nodes, if you need a phy-phandle pointer anyway?

So we know about the other phys and switches on the MDIO bus, can load
the driver for them, etc. This is standard policy for a bus
driver. When you instantiate the bus, you enumerate it to see what is
connected to it. You do that either with of_mdiobus_register() or
mdiobus_register().

However, i do agree about having a helper do the phy-handle parsing
would be nice, and it should also handle fixed phys as well.

      Andrew
Timur Tabi Aug. 25, 2016, 11:38 p.m. UTC | #8
Florian Fainelli wrote:
>>> >>Since you have a check on CONFIG_QCOM_EMAC in emac/Makefile, you could
>>> >>always recurse into that directory while building (use obj-y).
>> >
>> >Obviously, having "obj-$(CONFIG_QCOM_EMAC)" in both Makefiles is
>> >redundant, but wouldn't it make more sense to change
>> >"obj-$(CONFIG_QCOM_EMAC)" to "obj-y" in
>> >drivers/net/ethernet/qualcomm/emac/Makefile, so that I only recurse if
>> >necessary?

> Whichever makes the most sense, when there is a directory involved, my
> preference is to always recurse in that directory and selectively
> compile from there, since the Kconfig/Makefile options are all located
> within the same hierarchical level, just a preference.

It turns out that the way I changed it in v9 prevents the driver from 
being built as a module.  I changed the wrong Makefile.  I will have to 
post a v10.
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt
new file mode 100644
index 0000000..1381089
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qcom-emac.txt
@@ -0,0 +1,64 @@ 
+Qualcomm EMAC Gigabit Ethernet Controller
+
+Required properties:
+- compatible : Should be "qcom,fsm9900-emac" or "qcom,qdf2432-emac", depending
+	on the version of the internal PHY.  "qcom,fsm9900-emac" is for v1,
+	and "qcom,qdf2432-emac" is for v2.
+- reg : Offset and length of the register regions for the device
+- reg-names : Register region names referenced in 'reg' above.
+	Required register resource entries are:
+	"base"   : EMAC controller base register block.
+	"csr"    : EMAC wrapper register block.
+	"sgmii"  : EMAC SGMII PHY register block.
+	Optional register resource entries are:
+	"ptp"    : EMAC PTP (1588) register block.
+- interrupts : Interrupt numbers used by this controller
+- interrupt-names : Interrupt resource names referenced in 'interrupts' above.
+	Required interrupt resource entries are:
+	"emac_core0"   : EMAC core0 interrupt.
+	"sgmii_irq"   : EMAC SGMII interrupt.
+- mac-address               : The 6-byte MAC address. If present, it is the
+			      default MAC address.
+
+The external phy child node:
+- compatible : Should be "qcom,fsm9900-emac-phy".
+- reg : The phy address
+
+Example:
+soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	dma-ranges = <0 0 0xffffffff>;
+
+	emac0: ethernet@feb20000 {
+		compatible = "qcom,fsm9900-emac";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg-names = "base", "csr", "ptp", "sgmii";
+		reg =   <0xfeb20000 0x10000>,
+			<0xfeb36000 0x1000>,
+			<0xfeb3c000 0x4000>,
+			<0xfeb38000 0x400>;
+		interrupt-parent = <&emac0>;
+		#interrupt-cells = <1>;
+		interrupts = <76 80>;
+		interrupt-names = "emac_core0", "sgmii_irq";
+		phy0: ethernet-phy@0 {
+			compatible = "qcom,fsm9900-emac-phy";
+			reg = <0>;
+		}
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mdio_pins_a>;
+	};
+
+	tlmm: pinctrl@fd510000 {
+		compatible = "qcom,fsm9900-pinctrl";
+
+		mdio_pins_a: mdio {
+			state {
+				pins = "gpio123", "gpio124";
+				function = "mdio";
+			};
+		};
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index 952fd2a..38dabdf 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9404,6 +9404,12 @@  T:	git git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
 S:	Supported
 F:	drivers/net/wireless/ath/ath10k/
 
+QUALCOMM EMAC GIGABIT ETHERNET DRIVER
+M:	Timur Tabi <timur@codeaurora.org>
+L:	netdev@vger.kernel.org
+S:	Supported
+F:	drivers/net/ethernet/qualcomm/emac/
+
 QUALCOMM HEXAGON ARCHITECTURE
 M:	Richard Kuo <rkuo@codeaurora.org>
 L:	linux-hexagon@vger.kernel.org
diff --git a/drivers/net/ethernet/qualcomm/Kconfig b/drivers/net/ethernet/qualcomm/Kconfig
index a76e380..85b599f 100644
--- a/drivers/net/ethernet/qualcomm/Kconfig
+++ b/drivers/net/ethernet/qualcomm/Kconfig
@@ -24,4 +24,15 @@  config QCA7000
 	  To compile this driver as a module, choose M here. The module
 	  will be called qcaspi.
 
+config QCOM_EMAC
+	tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
+	select CRC32
+	---help---
+	  This driver supports the Qualcomm Technologies, Inc. Gigabit
+	  Ethernet Media Access Controller (EMAC). The controller
+	  supports IEEE 802.3-2002, half-duplex mode at 10/100 Mb/s,
+	  full-duplex mode at 10/100/1000Mb/s, Wake On LAN (WOL) for
+	  low power, Receive-Side Scaling (RSS), and IEEE 1588-2008
+	  Precision Clock Synchronization Protocol.
+
 endif # NET_VENDOR_QUALCOMM
diff --git a/drivers/net/ethernet/qualcomm/Makefile b/drivers/net/ethernet/qualcomm/Makefile
index 9da2d75..1b3a0ce 100644
--- a/drivers/net/ethernet/qualcomm/Makefile
+++ b/drivers/net/ethernet/qualcomm/Makefile
@@ -4,3 +4,5 @@ 
 
 obj-$(CONFIG_QCA7000) += qcaspi.o
 qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o
+
+obj-$(CONFIG_QCOM_EMAC) += emac/
diff --git a/drivers/net/ethernet/qualcomm/emac/Makefile b/drivers/net/ethernet/qualcomm/emac/Makefile
new file mode 100644
index 0000000..01ee144
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/Makefile
@@ -0,0 +1,7 @@ 
+#
+# Makefile for the Qualcomm Technologies, Inc. EMAC Gigabit Ethernet driver
+#
+
+obj-$(CONFIG_QCOM_EMAC) += qcom-emac.o
+
+qcom-emac-objs := emac.o emac-mac.o emac-phy.o emac-sgmii.o
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-mac.c b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
new file mode 100644
index 0000000..6ebfa66
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-mac.c
@@ -0,0 +1,1532 @@ 
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC Ethernet Controller MAC layer support
+ */
+
+#include <linux/tcp.h>
+#include <linux/ip.h>
+#include <linux/ipv6.h>
+#include <linux/crc32.h>
+#include <linux/if_vlan.h>
+#include <linux/jiffies.h>
+#include <linux/phy.h>
+#include <linux/of.h>
+#include <net/ip6_checksum.h>
+#include "emac.h"
+#include "emac-sgmii.h"
+
+/* EMAC base register offsets */
+#define EMAC_MAC_CTRL			0x001480
+#define EMAC_WOL_CTRL0			0x0014a0
+#define EMAC_RSS_KEY0			0x0014b0
+#define EMAC_H1TPD_BASE_ADDR_LO		0x0014e0
+#define EMAC_H2TPD_BASE_ADDR_LO		0x0014e4
+#define EMAC_H3TPD_BASE_ADDR_LO		0x0014e8
+#define EMAC_INTER_SRAM_PART9		0x001534
+#define EMAC_DESC_CTRL_0		0x001540
+#define EMAC_DESC_CTRL_1		0x001544
+#define EMAC_DESC_CTRL_2		0x001550
+#define EMAC_DESC_CTRL_10		0x001554
+#define EMAC_DESC_CTRL_12		0x001558
+#define EMAC_DESC_CTRL_13		0x00155c
+#define EMAC_DESC_CTRL_3		0x001560
+#define EMAC_DESC_CTRL_4		0x001564
+#define EMAC_DESC_CTRL_5		0x001568
+#define EMAC_DESC_CTRL_14		0x00156c
+#define EMAC_DESC_CTRL_15		0x001570
+#define EMAC_DESC_CTRL_16		0x001574
+#define EMAC_DESC_CTRL_6		0x001578
+#define EMAC_DESC_CTRL_8		0x001580
+#define EMAC_DESC_CTRL_9		0x001584
+#define EMAC_DESC_CTRL_11		0x001588
+#define EMAC_TXQ_CTRL_0			0x001590
+#define EMAC_TXQ_CTRL_1			0x001594
+#define EMAC_TXQ_CTRL_2			0x001598
+#define EMAC_RXQ_CTRL_0			0x0015a0
+#define EMAC_RXQ_CTRL_1			0x0015a4
+#define EMAC_RXQ_CTRL_2			0x0015a8
+#define EMAC_RXQ_CTRL_3			0x0015ac
+#define EMAC_BASE_CPU_NUMBER		0x0015b8
+#define EMAC_DMA_CTRL			0x0015c0
+#define EMAC_MAILBOX_0			0x0015e0
+#define EMAC_MAILBOX_5			0x0015e4
+#define EMAC_MAILBOX_6			0x0015e8
+#define EMAC_MAILBOX_13			0x0015ec
+#define EMAC_MAILBOX_2			0x0015f4
+#define EMAC_MAILBOX_3			0x0015f8
+#define EMAC_MAILBOX_11			0x00160c
+#define EMAC_AXI_MAST_CTRL		0x001610
+#define EMAC_MAILBOX_12			0x001614
+#define EMAC_MAILBOX_9			0x001618
+#define EMAC_MAILBOX_10			0x00161c
+#define EMAC_ATHR_HEADER_CTRL		0x001620
+#define EMAC_CLK_GATE_CTRL		0x001814
+#define EMAC_MISC_CTRL			0x001990
+#define EMAC_MAILBOX_7			0x0019e0
+#define EMAC_MAILBOX_8			0x0019e4
+#define EMAC_MAILBOX_15			0x001bd4
+#define EMAC_MAILBOX_16			0x001bd8
+
+/* EMAC_MAC_CTRL */
+#define SINGLE_PAUSE_MODE       	0x10000000
+#define DEBUG_MODE                      0x08000000
+#define BROAD_EN                        0x04000000
+#define MULTI_ALL                       0x02000000
+#define RX_CHKSUM_EN                    0x01000000
+#define HUGE                            0x00800000
+#define SPEED(x)			(((x) & 0x3) << 20)
+#define SPEED_MASK			SPEED(0x3)
+#define SIMR                            0x00080000
+#define TPAUSE                          0x00010000
+#define PROM_MODE                       0x00008000
+#define VLAN_STRIP                      0x00004000
+#define PRLEN_BMSK                      0x00003c00
+#define PRLEN_SHFT                      10
+#define HUGEN                           0x00000200
+#define FLCHK                           0x00000100
+#define PCRCE                           0x00000080
+#define CRCE                            0x00000040
+#define FULLD                           0x00000020
+#define MAC_LP_EN                       0x00000010
+#define RXFC                            0x00000008
+#define TXFC                            0x00000004
+#define RXEN                            0x00000002
+#define TXEN                            0x00000001
+
+
+/* EMAC_WOL_CTRL0 */
+#define LK_CHG_PME			0x20
+#define LK_CHG_EN			0x10
+#define MG_FRAME_PME			0x8
+#define MG_FRAME_EN			0x4
+#define WK_FRAME_EN			0x1
+
+/* EMAC_DESC_CTRL_3 */
+#define RFD_RING_SIZE_BMSK                                       0xfff
+
+/* EMAC_DESC_CTRL_4 */
+#define RX_BUFFER_SIZE_BMSK                                     0xffff
+
+/* EMAC_DESC_CTRL_6 */
+#define RRD_RING_SIZE_BMSK                                       0xfff
+
+/* EMAC_DESC_CTRL_9 */
+#define TPD_RING_SIZE_BMSK                                      0xffff
+
+/* EMAC_TXQ_CTRL_0 */
+#define NUM_TXF_BURST_PREF_BMSK                             0xffff0000
+#define NUM_TXF_BURST_PREF_SHFT                                     16
+#define LS_8023_SP                                                0x80
+#define TXQ_MODE                                                  0x40
+#define TXQ_EN                                                    0x20
+#define IP_OP_SP                                                  0x10
+#define NUM_TPD_BURST_PREF_BMSK                                    0xf
+#define NUM_TPD_BURST_PREF_SHFT                                      0
+
+/* EMAC_TXQ_CTRL_1 */
+#define JUMBO_TASK_OFFLOAD_THRESHOLD_BMSK                        0x7ff
+
+/* EMAC_TXQ_CTRL_2 */
+#define TXF_HWM_BMSK                                         0xfff0000
+#define TXF_LWM_BMSK                                             0xfff
+
+/* EMAC_RXQ_CTRL_0 */
+#define RXQ_EN                                                 BIT(31)
+#define CUT_THRU_EN                                            BIT(30)
+#define RSS_HASH_EN                                            BIT(29)
+#define NUM_RFD_BURST_PREF_BMSK                              0x3f00000
+#define NUM_RFD_BURST_PREF_SHFT                                     20
+#define IDT_TABLE_SIZE_BMSK                                    0x1ff00
+#define IDT_TABLE_SIZE_SHFT                                          8
+#define SP_IPV6                                                   0x80
+
+/* EMAC_RXQ_CTRL_1 */
+#define JUMBO_1KAH_BMSK                                         0xf000
+#define JUMBO_1KAH_SHFT                                             12
+#define RFD_PREF_LOW_TH                                           0x10
+#define RFD_PREF_LOW_THRESHOLD_BMSK                              0xfc0
+#define RFD_PREF_LOW_THRESHOLD_SHFT                                  6
+#define RFD_PREF_UP_TH                                            0x10
+#define RFD_PREF_UP_THRESHOLD_BMSK                                0x3f
+#define RFD_PREF_UP_THRESHOLD_SHFT                                   0
+
+/* EMAC_RXQ_CTRL_2 */
+#define RXF_DOF_THRESFHOLD                                       0x1a0
+#define RXF_DOF_THRESHOLD_BMSK                               0xfff0000
+#define RXF_DOF_THRESHOLD_SHFT                                      16
+#define RXF_UOF_THRESFHOLD                                        0xbe
+#define RXF_UOF_THRESHOLD_BMSK                                   0xfff
+#define RXF_UOF_THRESHOLD_SHFT                                       0
+
+/* EMAC_RXQ_CTRL_3 */
+#define RXD_TIMER_BMSK                                      0xffff0000
+#define RXD_THRESHOLD_BMSK                                       0xfff
+#define RXD_THRESHOLD_SHFT                                           0
+
+/* EMAC_DMA_CTRL */
+#define DMAW_DLY_CNT_BMSK                                      0xf0000
+#define DMAW_DLY_CNT_SHFT                                           16
+#define DMAR_DLY_CNT_BMSK                                       0xf800
+#define DMAR_DLY_CNT_SHFT                                           11
+#define DMAR_REQ_PRI                                             0x400
+#define REGWRBLEN_BMSK                                           0x380
+#define REGWRBLEN_SHFT                                               7
+#define REGRDBLEN_BMSK                                            0x70
+#define REGRDBLEN_SHFT                                               4
+#define OUT_ORDER_MODE                                             0x4
+#define ENH_ORDER_MODE                                             0x2
+#define IN_ORDER_MODE                                              0x1
+
+/* EMAC_MAILBOX_13 */
+#define RFD3_PROC_IDX_BMSK                                   0xfff0000
+#define RFD3_PROC_IDX_SHFT                                          16
+#define RFD3_PROD_IDX_BMSK                                       0xfff
+#define RFD3_PROD_IDX_SHFT                                           0
+
+/* EMAC_MAILBOX_2 */
+#define NTPD_CONS_IDX_BMSK                                  0xffff0000
+#define NTPD_CONS_IDX_SHFT                                          16
+
+/* EMAC_MAILBOX_3 */
+#define RFD0_CONS_IDX_BMSK                                       0xfff
+#define RFD0_CONS_IDX_SHFT                                           0
+
+/* EMAC_MAILBOX_11 */
+#define H3TPD_PROD_IDX_BMSK                                 0xffff0000
+#define H3TPD_PROD_IDX_SHFT                                         16
+
+/* EMAC_AXI_MAST_CTRL */
+#define DATA_BYTE_SWAP                                             0x8
+#define MAX_BOUND                                                  0x2
+#define MAX_BTYPE                                                  0x1
+
+/* EMAC_MAILBOX_12 */
+#define H3TPD_CONS_IDX_BMSK                                 0xffff0000
+#define H3TPD_CONS_IDX_SHFT                                         16
+
+/* EMAC_MAILBOX_9 */
+#define H2TPD_PROD_IDX_BMSK                                     0xffff
+#define H2TPD_PROD_IDX_SHFT                                          0
+
+/* EMAC_MAILBOX_10 */
+#define H1TPD_CONS_IDX_BMSK                                 0xffff0000
+#define H1TPD_CONS_IDX_SHFT                                         16
+#define H2TPD_CONS_IDX_BMSK                                     0xffff
+#define H2TPD_CONS_IDX_SHFT                                          0
+
+/* EMAC_ATHR_HEADER_CTRL */
+#define HEADER_CNT_EN                                              0x2
+#define HEADER_ENABLE                                              0x1
+
+/* EMAC_MAILBOX_0 */
+#define RFD0_PROC_IDX_BMSK                                   0xfff0000
+#define RFD0_PROC_IDX_SHFT                                          16
+#define RFD0_PROD_IDX_BMSK                                       0xfff
+#define RFD0_PROD_IDX_SHFT                                           0
+
+/* EMAC_MAILBOX_5 */
+#define RFD1_PROC_IDX_BMSK                                   0xfff0000
+#define RFD1_PROC_IDX_SHFT                                          16
+#define RFD1_PROD_IDX_BMSK                                       0xfff
+#define RFD1_PROD_IDX_SHFT                                           0
+
+/* EMAC_MISC_CTRL */
+#define RX_UNCPL_INT_EN                                            0x1
+
+/* EMAC_MAILBOX_7 */
+#define RFD2_CONS_IDX_BMSK                                   0xfff0000
+#define RFD2_CONS_IDX_SHFT                                          16
+#define RFD1_CONS_IDX_BMSK                                       0xfff
+#define RFD1_CONS_IDX_SHFT                                           0
+
+/* EMAC_MAILBOX_8 */
+#define RFD3_CONS_IDX_BMSK                                       0xfff
+#define RFD3_CONS_IDX_SHFT                                           0
+
+/* EMAC_MAILBOX_15 */
+#define NTPD_PROD_IDX_BMSK                                      0xffff
+#define NTPD_PROD_IDX_SHFT                                           0
+
+/* EMAC_MAILBOX_16 */
+#define H1TPD_PROD_IDX_BMSK                                     0xffff
+#define H1TPD_PROD_IDX_SHFT                                          0
+
+#define RXQ0_RSS_HSTYP_IPV6_TCP_EN                                0x20
+#define RXQ0_RSS_HSTYP_IPV6_EN                                    0x10
+#define RXQ0_RSS_HSTYP_IPV4_TCP_EN                                 0x8
+#define RXQ0_RSS_HSTYP_IPV4_EN                                     0x4
+
+/* EMAC_EMAC_WRAPPER_TX_TS_INX */
+#define EMAC_WRAPPER_TX_TS_EMPTY                               BIT(31)
+#define EMAC_WRAPPER_TX_TS_INX_BMSK                             0xffff
+
+struct emac_skb_cb {
+	u32           tpd_idx;
+	unsigned long jiffies;
+};
+
+#define EMAC_SKB_CB(skb)	((struct emac_skb_cb *)(skb)->cb)
+#define EMAC_RSS_IDT_SIZE	256
+#define JUMBO_1KAH		0x4
+#define RXD_TH			0x100
+#define EMAC_TPD_LAST_FRAGMENT	0x80000000
+#define EMAC_TPD_TSTAMP_SAVE	0x80000000
+
+/* EMAC Errors in emac_rrd.word[3] */
+#define EMAC_RRD_L4F		BIT(14)
+#define EMAC_RRD_IPF		BIT(15)
+#define EMAC_RRD_CRC		BIT(21)
+#define EMAC_RRD_FAE		BIT(22)
+#define EMAC_RRD_TRN		BIT(23)
+#define EMAC_RRD_RNT		BIT(24)
+#define EMAC_RRD_INC		BIT(25)
+#define EMAC_RRD_FOV		BIT(29)
+#define EMAC_RRD_LEN		BIT(30)
+
+/* Error bits that will result in a received frame being discarded */
+#define EMAC_RRD_ERROR (EMAC_RRD_IPF | EMAC_RRD_CRC | EMAC_RRD_FAE | \
+			EMAC_RRD_TRN | EMAC_RRD_RNT | EMAC_RRD_INC | \
+			EMAC_RRD_FOV | EMAC_RRD_LEN)
+#define EMAC_RRD_STATS_DW_IDX 3
+
+#define EMAC_RRD(RXQ, SIZE, IDX)	((RXQ)->rrd.v_addr + (SIZE * (IDX)))
+#define EMAC_RFD(RXQ, SIZE, IDX)	((RXQ)->rfd.v_addr + (SIZE * (IDX)))
+#define EMAC_TPD(TXQ, SIZE, IDX)	((TXQ)->tpd.v_addr + (SIZE * (IDX)))
+
+#define GET_RFD_BUFFER(RXQ, IDX)	(&((RXQ)->rfd.rfbuff[(IDX)]))
+#define GET_TPD_BUFFER(RTQ, IDX)	(&((RTQ)->tpd.tpbuff[(IDX)]))
+
+#define EMAC_TX_POLL_HWTXTSTAMP_THRESHOLD	8
+
+#define ISR_RX_PKT      (\
+	RX_PKT_INT0     |\
+	RX_PKT_INT1     |\
+	RX_PKT_INT2     |\
+	RX_PKT_INT3)
+
+void emac_mac_multicast_addr_set(struct emac_adapter *adpt, u8 *addr)
+{
+	u32 crc32, bit, reg, mta;
+
+	/* Calculate the CRC of the MAC address */
+	crc32 = ether_crc(ETH_ALEN, addr);
+
+	/* The HASH Table is an array of 2 32-bit registers. It is
+	 * treated like an array of 64 bits (BitArray[hash_value]).
+	 * Use the upper 6 bits of the above CRC as the hash value.
+	 */
+	reg = (crc32 >> 31) & 0x1;
+	bit = (crc32 >> 26) & 0x1F;
+
+	mta = readl(adpt->base + EMAC_HASH_TAB_REG0 + (reg << 2));
+	mta |= BIT(bit);
+	writel(mta, adpt->base + EMAC_HASH_TAB_REG0 + (reg << 2));
+}
+
+void emac_mac_multicast_addr_clear(struct emac_adapter *adpt)
+{
+	writel(0, adpt->base + EMAC_HASH_TAB_REG0);
+	writel(0, adpt->base + EMAC_HASH_TAB_REG1);
+}
+
+/* definitions for RSS */
+#define EMAC_RSS_KEY(_i, _type) \
+		(EMAC_RSS_KEY0 + ((_i) * sizeof(_type)))
+#define EMAC_RSS_TBL(_i, _type) \
+		(EMAC_IDT_TABLE0 + ((_i) * sizeof(_type)))
+
+/* Config MAC modes */
+void emac_mac_mode_config(struct emac_adapter *adpt)
+{
+	struct net_device *netdev = adpt->netdev;
+	u32 mac;
+
+	mac = readl(adpt->base + EMAC_MAC_CTRL);
+	mac &= ~(VLAN_STRIP | PROM_MODE | MULTI_ALL | MAC_LP_EN);
+
+	if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX)
+		mac |= VLAN_STRIP;
+
+	if (netdev->flags & IFF_PROMISC)
+		mac |= PROM_MODE;
+
+	if (netdev->flags & IFF_ALLMULTI)
+		mac |= MULTI_ALL;
+
+	writel(mac, adpt->base + EMAC_MAC_CTRL);
+}
+
+/* Config descriptor rings */
+static void emac_mac_dma_rings_config(struct emac_adapter *adpt)
+{
+	static const unsigned short tpd_q_offset[] = {
+		EMAC_DESC_CTRL_8,        EMAC_H1TPD_BASE_ADDR_LO,
+		EMAC_H2TPD_BASE_ADDR_LO, EMAC_H3TPD_BASE_ADDR_LO};
+	static const unsigned short rfd_q_offset[] = {
+		EMAC_DESC_CTRL_2,        EMAC_DESC_CTRL_10,
+		EMAC_DESC_CTRL_12,       EMAC_DESC_CTRL_13};
+	static const unsigned short rrd_q_offset[] = {
+		EMAC_DESC_CTRL_5,        EMAC_DESC_CTRL_14,
+		EMAC_DESC_CTRL_15,       EMAC_DESC_CTRL_16};
+
+	/* TPD (Transmit Packet Descriptor) */
+	writel(upper_32_bits(adpt->tx_q.tpd.dma_addr),
+	       adpt->base + EMAC_DESC_CTRL_1);
+
+	writel(lower_32_bits(adpt->tx_q.tpd.dma_addr),
+	       adpt->base + tpd_q_offset[0]);
+
+	writel(adpt->tx_q.tpd.count & TPD_RING_SIZE_BMSK,
+	       adpt->base + EMAC_DESC_CTRL_9);
+
+	/* RFD (Receive Free Descriptor) & RRD (Receive Return Descriptor) */
+	writel(upper_32_bits(adpt->rx_q.rfd.dma_addr),
+	       adpt->base + EMAC_DESC_CTRL_0);
+
+	writel(lower_32_bits(adpt->rx_q.rfd.dma_addr),
+	       adpt->base + rfd_q_offset[0]);
+	writel(lower_32_bits(adpt->rx_q.rrd.dma_addr),
+	       adpt->base + rrd_q_offset[0]);
+
+	writel(adpt->rx_q.rfd.count & RFD_RING_SIZE_BMSK,
+	       adpt->base + EMAC_DESC_CTRL_3);
+	writel(adpt->rx_q.rrd.count & RRD_RING_SIZE_BMSK,
+	       adpt->base + EMAC_DESC_CTRL_6);
+
+	writel(adpt->rxbuf_size & RX_BUFFER_SIZE_BMSK,
+	       adpt->base + EMAC_DESC_CTRL_4);
+
+	writel(0, adpt->base + EMAC_DESC_CTRL_11);
+
+	/* Load all of the base addresses above and ensure that triggering HW to
+	 * read ring pointers is flushed
+	 */
+	writel(1, adpt->base + EMAC_INTER_SRAM_PART9);
+}
+
+/* Config transmit parameters */
+static void emac_mac_tx_config(struct emac_adapter *adpt)
+{
+	u32 val;
+
+	writel((EMAC_MAX_TX_OFFLOAD_THRESH >> 3) &
+	       JUMBO_TASK_OFFLOAD_THRESHOLD_BMSK, adpt->base + EMAC_TXQ_CTRL_1);
+
+	val = (adpt->tpd_burst << NUM_TPD_BURST_PREF_SHFT) &
+	       NUM_TPD_BURST_PREF_BMSK;
+
+	val |= TXQ_MODE | LS_8023_SP;
+	val |= (0x0100 << NUM_TXF_BURST_PREF_SHFT) &
+		NUM_TXF_BURST_PREF_BMSK;
+
+	writel(val, adpt->base + EMAC_TXQ_CTRL_0);
+	emac_reg_update32(adpt->base + EMAC_TXQ_CTRL_2,
+			  (TXF_HWM_BMSK | TXF_LWM_BMSK), 0);
+}
+
+/* Config receive parameters */
+static void emac_mac_rx_config(struct emac_adapter *adpt)
+{
+	u32 val;
+
+	val = (adpt->rfd_burst << NUM_RFD_BURST_PREF_SHFT) &
+	       NUM_RFD_BURST_PREF_BMSK;
+	val |= (SP_IPV6 | CUT_THRU_EN);
+
+	writel(val, adpt->base + EMAC_RXQ_CTRL_0);
+
+	val = readl(adpt->base + EMAC_RXQ_CTRL_1);
+	val &= ~(JUMBO_1KAH_BMSK | RFD_PREF_LOW_THRESHOLD_BMSK |
+		 RFD_PREF_UP_THRESHOLD_BMSK);
+	val |= (JUMBO_1KAH << JUMBO_1KAH_SHFT) |
+		(RFD_PREF_LOW_TH << RFD_PREF_LOW_THRESHOLD_SHFT) |
+		(RFD_PREF_UP_TH  << RFD_PREF_UP_THRESHOLD_SHFT);
+	writel(val, adpt->base + EMAC_RXQ_CTRL_1);
+
+	val = readl(adpt->base + EMAC_RXQ_CTRL_2);
+	val &= ~(RXF_DOF_THRESHOLD_BMSK | RXF_UOF_THRESHOLD_BMSK);
+	val |= (RXF_DOF_THRESFHOLD  << RXF_DOF_THRESHOLD_SHFT) |
+		(RXF_UOF_THRESFHOLD << RXF_UOF_THRESHOLD_SHFT);
+	writel(val, adpt->base + EMAC_RXQ_CTRL_2);
+
+	val = readl(adpt->base + EMAC_RXQ_CTRL_3);
+	val &= ~(RXD_TIMER_BMSK | RXD_THRESHOLD_BMSK);
+	val |= RXD_TH << RXD_THRESHOLD_SHFT;
+	writel(val, adpt->base + EMAC_RXQ_CTRL_3);
+}
+
+/* Config dma */
+static void emac_mac_dma_config(struct emac_adapter *adpt)
+{
+	u32 dma_ctrl = DMAR_REQ_PRI;
+
+	switch (adpt->dma_order) {
+	case emac_dma_ord_in:
+		dma_ctrl |= IN_ORDER_MODE;
+		break;
+	case emac_dma_ord_enh:
+		dma_ctrl |= ENH_ORDER_MODE;
+		break;
+	case emac_dma_ord_out:
+		dma_ctrl |= OUT_ORDER_MODE;
+		break;
+	default:
+		break;
+	}
+
+	dma_ctrl |= (((u32)adpt->dmar_block) << REGRDBLEN_SHFT) &
+						REGRDBLEN_BMSK;
+	dma_ctrl |= (((u32)adpt->dmaw_block) << REGWRBLEN_SHFT) &
+						REGWRBLEN_BMSK;
+	dma_ctrl |= (((u32)adpt->dmar_dly_cnt) << DMAR_DLY_CNT_SHFT) &
+						DMAR_DLY_CNT_BMSK;
+	dma_ctrl |= (((u32)adpt->dmaw_dly_cnt) << DMAW_DLY_CNT_SHFT) &
+						DMAW_DLY_CNT_BMSK;
+
+	/* config DMA and ensure that configuration is flushed to HW */
+	writel(dma_ctrl, adpt->base + EMAC_DMA_CTRL);
+}
+
+/* set MAC address */
+static void emac_set_mac_address(struct emac_adapter *adpt, u8 *addr)
+{
+	u32 sta;
+
+	/* for example: 00-A0-C6-11-22-33
+	 * 0<-->C6112233, 1<-->00A0.
+	 */
+
+	/* low 32bit word */
+	sta = (((u32)addr[2]) << 24) | (((u32)addr[3]) << 16) |
+	      (((u32)addr[4]) << 8)  | (((u32)addr[5]));
+	writel(sta, adpt->base + EMAC_MAC_STA_ADDR0);
+
+	/* hight 32bit word */
+	sta = (((u32)addr[0]) << 8) | (u32)addr[1];
+	writel(sta, adpt->base + EMAC_MAC_STA_ADDR1);
+}
+
+void emac_mac_config(struct emac_adapter *adpt)
+{
+	struct net_device *netdev = adpt->netdev;
+	unsigned int max_frame;
+	u32 val;
+
+	emac_set_mac_address(adpt, netdev->dev_addr);
+
+	max_frame = netdev->mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
+	adpt->rxbuf_size = netdev->mtu > EMAC_DEF_RX_BUF_SIZE ?
+		ALIGN(max_frame, 8) : EMAC_DEF_RX_BUF_SIZE;
+
+	emac_mac_dma_rings_config(adpt);
+
+	writel(netdev->mtu + ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN,
+	       adpt->base + EMAC_MAX_FRAM_LEN_CTRL);
+
+	emac_mac_tx_config(adpt);
+	emac_mac_rx_config(adpt);
+	emac_mac_dma_config(adpt);
+
+	val = readl(adpt->base + EMAC_AXI_MAST_CTRL);
+	val &= ~(DATA_BYTE_SWAP | MAX_BOUND);
+	val |= MAX_BTYPE;
+	writel(val, adpt->base + EMAC_AXI_MAST_CTRL);
+	writel(0, adpt->base + EMAC_CLK_GATE_CTRL);
+	writel(RX_UNCPL_INT_EN, adpt->base + EMAC_MISC_CTRL);
+}
+
+void emac_mac_reset(struct emac_adapter *adpt)
+{
+	emac_mac_stop(adpt);
+
+	emac_reg_update32(adpt->base + EMAC_DMA_MAS_CTRL, 0, SOFT_RST);
+	usleep_range(100, 150); /* reset may take up to 100usec */
+
+	/* interrupt clear-on-read */
+	emac_reg_update32(adpt->base + EMAC_DMA_MAS_CTRL, 0, INT_RD_CLR_EN);
+}
+
+void emac_mac_start(struct emac_adapter *adpt)
+{
+	struct phy_device *phydev = adpt->phydev;
+	u32 mac, csr1;
+
+	/* enable tx queue */
+	emac_reg_update32(adpt->base + EMAC_TXQ_CTRL_0, 0, TXQ_EN);
+
+	/* enable rx queue */
+	emac_reg_update32(adpt->base + EMAC_RXQ_CTRL_0, 0, RXQ_EN);
+
+	/* enable mac control */
+	mac = readl(adpt->base + EMAC_MAC_CTRL);
+	csr1 = readl(adpt->csr + EMAC_EMAC_WRAPPER_CSR1);
+
+	mac |= TXEN | RXEN;     /* enable RX/TX */
+
+	/* We don't have ethtool support yet, so force flow-control mode
+	 * to 'full' always.
+	 */
+	mac |= TXFC | RXFC;
+
+	/* setup link speed */
+	mac &= ~SPEED_MASK;
+	if (phydev->speed == SPEED_1000) {
+		mac |= SPEED(2);
+		csr1 |= FREQ_MODE;
+	} else {
+		mac |= SPEED(1);
+		csr1 &= ~FREQ_MODE;
+	}
+
+	if (phydev->duplex == DUPLEX_FULL)
+		mac |= FULLD;
+	else
+		mac &= ~FULLD;
+
+	/* other parameters */
+	mac |= (CRCE | PCRCE);
+	mac |= ((adpt->preamble << PRLEN_SHFT) & PRLEN_BMSK);
+	mac |= BROAD_EN;
+	mac |= FLCHK;
+	mac &= ~RX_CHKSUM_EN;
+	mac &= ~(HUGEN | VLAN_STRIP | TPAUSE | SIMR | HUGE | MULTI_ALL |
+		 DEBUG_MODE | SINGLE_PAUSE_MODE);
+
+	writel_relaxed(csr1, adpt->csr + EMAC_EMAC_WRAPPER_CSR1);
+
+	writel_relaxed(mac, adpt->base + EMAC_MAC_CTRL);
+
+	/* enable interrupt read clear, low power sleep mode and
+	 * the irq moderators
+	 */
+
+	writel_relaxed(adpt->irq_mod, adpt->base + EMAC_IRQ_MOD_TIM_INIT);
+	writel_relaxed(INT_RD_CLR_EN | LPW_MODE | IRQ_MODERATOR_EN |
+			IRQ_MODERATOR2_EN, adpt->base + EMAC_DMA_MAS_CTRL);
+
+	emac_mac_mode_config(adpt);
+
+	emac_reg_update32(adpt->base + EMAC_ATHR_HEADER_CTRL,
+			  (HEADER_ENABLE | HEADER_CNT_EN), 0);
+
+	emac_reg_update32(adpt->csr + EMAC_EMAC_WRAPPER_CSR2, 0, WOL_EN);
+}
+
+void emac_mac_stop(struct emac_adapter *adpt)
+{
+	emac_reg_update32(adpt->base + EMAC_RXQ_CTRL_0, RXQ_EN, 0);
+	emac_reg_update32(adpt->base + EMAC_TXQ_CTRL_0, TXQ_EN, 0);
+	emac_reg_update32(adpt->base + EMAC_MAC_CTRL, TXEN | RXEN, 0);
+	usleep_range(1000, 1050); /* stopping mac may take upto 1msec */
+}
+
+/* Free all descriptors of given transmit queue */
+static void emac_tx_q_descs_free(struct emac_adapter *adpt)
+{
+	struct emac_tx_queue *tx_q = &adpt->tx_q;
+	unsigned int i;
+	size_t size;
+
+	/* ring already cleared, nothing to do */
+	if (!tx_q->tpd.tpbuff)
+		return;
+
+	for (i = 0; i < tx_q->tpd.count; i++) {
+		struct emac_buffer *tpbuf = GET_TPD_BUFFER(tx_q, i);
+
+		if (tpbuf->dma_addr) {
+			dma_unmap_single(adpt->netdev->dev.parent,
+					 tpbuf->dma_addr, tpbuf->length,
+					 DMA_TO_DEVICE);
+			tpbuf->dma_addr = 0;
+		}
+		if (tpbuf->skb) {
+			dev_kfree_skb_any(tpbuf->skb);
+			tpbuf->skb = NULL;
+		}
+	}
+
+	size = sizeof(struct emac_buffer) * tx_q->tpd.count;
+	memset(tx_q->tpd.tpbuff, 0, size);
+
+	/* clear the descriptor ring */
+	memset(tx_q->tpd.v_addr, 0, tx_q->tpd.size);
+
+	tx_q->tpd.consume_idx = 0;
+	tx_q->tpd.produce_idx = 0;
+}
+
+/* Free all descriptors of given receive queue */
+static void emac_rx_q_free_descs(struct emac_adapter *adpt)
+{
+	struct device *dev = adpt->netdev->dev.parent;
+	struct emac_rx_queue *rx_q = &adpt->rx_q;
+	unsigned int i;
+	size_t size;
+
+	/* ring already cleared, nothing to do */
+	if (!rx_q->rfd.rfbuff)
+		return;
+
+	for (i = 0; i < rx_q->rfd.count; i++) {
+		struct emac_buffer *rfbuf = GET_RFD_BUFFER(rx_q, i);
+
+		if (rfbuf->dma_addr) {
+			dma_unmap_single(dev, rfbuf->dma_addr, rfbuf->length,
+					 DMA_FROM_DEVICE);
+			rfbuf->dma_addr = 0;
+		}
+		if (rfbuf->skb) {
+			dev_kfree_skb(rfbuf->skb);
+			rfbuf->skb = NULL;
+		}
+	}
+
+	size =  sizeof(struct emac_buffer) * rx_q->rfd.count;
+	memset(rx_q->rfd.rfbuff, 0, size);
+
+	/* clear the descriptor rings */
+	memset(rx_q->rrd.v_addr, 0, rx_q->rrd.size);
+	rx_q->rrd.produce_idx = 0;
+	rx_q->rrd.consume_idx = 0;
+
+	memset(rx_q->rfd.v_addr, 0, rx_q->rfd.size);
+	rx_q->rfd.produce_idx = 0;
+	rx_q->rfd.consume_idx = 0;
+}
+
+/* Free all buffers associated with given transmit queue */
+static void emac_tx_q_bufs_free(struct emac_adapter *adpt)
+{
+	struct emac_tx_queue *tx_q = &adpt->tx_q;
+
+	emac_tx_q_descs_free(adpt);
+
+	kfree(tx_q->tpd.tpbuff);
+	tx_q->tpd.tpbuff = NULL;
+	tx_q->tpd.v_addr = NULL;
+	tx_q->tpd.dma_addr = 0;
+	tx_q->tpd.size = 0;
+}
+
+/* Allocate TX descriptor ring for the given transmit queue */
+static int emac_tx_q_desc_alloc(struct emac_adapter *adpt,
+				struct emac_tx_queue *tx_q)
+{
+	struct emac_ring_header *ring_header = &adpt->ring_header;
+	size_t size;
+
+	size = sizeof(struct emac_buffer) * tx_q->tpd.count;
+	tx_q->tpd.tpbuff = kzalloc(size, GFP_KERNEL);
+	if (!tx_q->tpd.tpbuff)
+		return -ENOMEM;
+
+	tx_q->tpd.size = tx_q->tpd.count * (adpt->tpd_size * 4);
+	tx_q->tpd.dma_addr = ring_header->dma_addr + ring_header->used;
+	tx_q->tpd.v_addr = ring_header->v_addr + ring_header->used;
+	ring_header->used += ALIGN(tx_q->tpd.size, 8);
+	tx_q->tpd.produce_idx = 0;
+	tx_q->tpd.consume_idx = 0;
+
+	return 0;
+}
+
+/* Free all buffers associated with given transmit queue */
+static void emac_rx_q_bufs_free(struct emac_adapter *adpt)
+{
+	struct emac_rx_queue *rx_q = &adpt->rx_q;
+
+	emac_rx_q_free_descs(adpt);
+
+	kfree(rx_q->rfd.rfbuff);
+	rx_q->rfd.rfbuff   = NULL;
+
+	rx_q->rfd.v_addr   = NULL;
+	rx_q->rfd.dma_addr = 0;
+	rx_q->rfd.size     = 0;
+
+	rx_q->rrd.v_addr   = NULL;
+	rx_q->rrd.dma_addr = 0;
+	rx_q->rrd.size     = 0;
+}
+
+/* Allocate RX descriptor rings for the given receive queue */
+static int emac_rx_descs_alloc(struct emac_adapter *adpt)
+{
+	struct emac_ring_header *ring_header = &adpt->ring_header;
+	struct emac_rx_queue *rx_q = &adpt->rx_q;
+	size_t size;
+
+	size = sizeof(struct emac_buffer) * rx_q->rfd.count;
+	rx_q->rfd.rfbuff = kzalloc(size, GFP_KERNEL);
+	if (!rx_q->rfd.rfbuff)
+		return -ENOMEM;
+
+	rx_q->rrd.size = rx_q->rrd.count * (adpt->rrd_size * 4);
+	rx_q->rfd.size = rx_q->rfd.count * (adpt->rfd_size * 4);
+
+	rx_q->rrd.dma_addr = ring_header->dma_addr + ring_header->used;
+	rx_q->rrd.v_addr   = ring_header->v_addr + ring_header->used;
+	ring_header->used += ALIGN(rx_q->rrd.size, 8);
+
+	rx_q->rfd.dma_addr = ring_header->dma_addr + ring_header->used;
+	rx_q->rfd.v_addr   = ring_header->v_addr + ring_header->used;
+	ring_header->used += ALIGN(rx_q->rfd.size, 8);
+
+	rx_q->rrd.produce_idx = 0;
+	rx_q->rrd.consume_idx = 0;
+
+	rx_q->rfd.produce_idx = 0;
+	rx_q->rfd.consume_idx = 0;
+
+	return 0;
+}
+
+/* Allocate all TX and RX descriptor rings */
+int emac_mac_rx_tx_rings_alloc_all(struct emac_adapter *adpt)
+{
+	struct emac_ring_header *ring_header = &adpt->ring_header;
+	struct device *dev = adpt->netdev->dev.parent;
+	unsigned int num_tx_descs = adpt->tx_desc_cnt;
+	unsigned int num_rx_descs = adpt->rx_desc_cnt;
+	int ret;
+
+	adpt->tx_q.tpd.count = adpt->tx_desc_cnt;
+
+	adpt->rx_q.rrd.count = adpt->rx_desc_cnt;
+	adpt->rx_q.rfd.count = adpt->rx_desc_cnt;
+
+	/* Ring DMA buffer. Each ring may need up to 8 bytes for alignment,
+	 * hence the additional padding bytes are allocated.
+	 */
+	ring_header->size = num_tx_descs * (adpt->tpd_size * 4) +
+			    num_rx_descs * (adpt->rfd_size * 4) +
+			    num_rx_descs * (adpt->rrd_size * 4) +
+			    8 + 2 * 8; /* 8 byte per one Tx and two Rx rings */
+
+	ring_header->used = 0;
+	ring_header->v_addr = dma_zalloc_coherent(dev, ring_header->size,
+						 &ring_header->dma_addr,
+						 GFP_KERNEL);
+	if (!ring_header->v_addr)
+		return -ENOMEM;
+
+	ring_header->used = ALIGN(ring_header->dma_addr, 8) -
+							ring_header->dma_addr;
+
+	ret = emac_tx_q_desc_alloc(adpt, &adpt->tx_q);
+	if (ret) {
+		netdev_err(adpt->netdev, "error: Tx Queue alloc failed\n");
+		goto err_alloc_tx;
+	}
+
+	ret = emac_rx_descs_alloc(adpt);
+	if (ret) {
+		netdev_err(adpt->netdev, "error: Rx Queue alloc failed\n");
+		goto err_alloc_rx;
+	}
+
+	return 0;
+
+err_alloc_rx:
+	emac_tx_q_bufs_free(adpt);
+err_alloc_tx:
+	dma_free_coherent(dev, ring_header->size,
+			  ring_header->v_addr, ring_header->dma_addr);
+
+	ring_header->v_addr   = NULL;
+	ring_header->dma_addr = 0;
+	ring_header->size     = 0;
+	ring_header->used     = 0;
+
+	return ret;
+}
+
+/* Free all TX and RX descriptor rings */
+void emac_mac_rx_tx_rings_free_all(struct emac_adapter *adpt)
+{
+	struct emac_ring_header *ring_header = &adpt->ring_header;
+	struct device *dev = adpt->netdev->dev.parent;
+
+	emac_tx_q_bufs_free(adpt);
+	emac_rx_q_bufs_free(adpt);
+
+	dma_free_coherent(dev, ring_header->size,
+			  ring_header->v_addr, ring_header->dma_addr);
+
+	ring_header->v_addr   = NULL;
+	ring_header->dma_addr = 0;
+	ring_header->size     = 0;
+	ring_header->used     = 0;
+}
+
+/* Initialize descriptor rings */
+static void emac_mac_rx_tx_ring_reset_all(struct emac_adapter *adpt)
+{
+	unsigned int i;
+
+	adpt->tx_q.tpd.produce_idx = 0;
+	adpt->tx_q.tpd.consume_idx = 0;
+	for (i = 0; i < adpt->tx_q.tpd.count; i++)
+		adpt->tx_q.tpd.tpbuff[i].dma_addr = 0;
+
+	adpt->rx_q.rrd.produce_idx = 0;
+	adpt->rx_q.rrd.consume_idx = 0;
+	adpt->rx_q.rfd.produce_idx = 0;
+	adpt->rx_q.rfd.consume_idx = 0;
+	for (i = 0; i < adpt->rx_q.rfd.count; i++)
+		adpt->rx_q.rfd.rfbuff[i].dma_addr = 0;
+}
+
+/* Produce new receive free descriptor */
+static void emac_mac_rx_rfd_create(struct emac_adapter *adpt,
+				   struct emac_rx_queue *rx_q,
+				   dma_addr_t addr)
+{
+	u32 *hw_rfd = EMAC_RFD(rx_q, adpt->rfd_size, rx_q->rfd.produce_idx);
+
+	*(hw_rfd++) = lower_32_bits(addr);
+	*hw_rfd = upper_32_bits(addr);
+
+	if (++rx_q->rfd.produce_idx == rx_q->rfd.count)
+		rx_q->rfd.produce_idx = 0;
+}
+
+/* Fill up receive queue's RFD with preallocated receive buffers */
+static void emac_mac_rx_descs_refill(struct emac_adapter *adpt,
+				    struct emac_rx_queue *rx_q)
+{
+	struct emac_buffer *curr_rxbuf;
+	struct emac_buffer *next_rxbuf;
+	unsigned int count = 0;
+	u32 next_produce_idx;
+
+	next_produce_idx = rx_q->rfd.produce_idx + 1;
+	if (next_produce_idx == rx_q->rfd.count)
+		next_produce_idx = 0;
+
+	curr_rxbuf = GET_RFD_BUFFER(rx_q, rx_q->rfd.produce_idx);
+	next_rxbuf = GET_RFD_BUFFER(rx_q, next_produce_idx);
+
+	/* this always has a blank rx_buffer*/
+	while (!next_rxbuf->dma_addr) {
+		struct sk_buff *skb;
+		int ret;
+
+		skb = __netdev_alloc_skb_ip_align(adpt->netdev,
+						  adpt->rxbuf_size, GFP_KERNEL);
+		if (!skb)
+			break;
+
+		curr_rxbuf->dma_addr =
+			dma_map_single(adpt->netdev->dev.parent, skb->data,
+				       curr_rxbuf->length, DMA_FROM_DEVICE);
+		ret = dma_mapping_error(adpt->netdev->dev.parent,
+					curr_rxbuf->dma_addr);
+		if (ret) {
+			dev_kfree_skb(skb);
+			break;
+		}
+		curr_rxbuf->skb = skb;
+		curr_rxbuf->length = adpt->rxbuf_size;
+
+		emac_mac_rx_rfd_create(adpt, rx_q, curr_rxbuf->dma_addr);
+		next_produce_idx = rx_q->rfd.produce_idx + 1;
+		if (next_produce_idx == rx_q->rfd.count)
+			next_produce_idx = 0;
+
+		curr_rxbuf = GET_RFD_BUFFER(rx_q, rx_q->rfd.produce_idx);
+		next_rxbuf = GET_RFD_BUFFER(rx_q, next_produce_idx);
+		count++;
+	}
+
+	if (count) {
+		u32 prod_idx = (rx_q->rfd.produce_idx << rx_q->produce_shift) &
+				rx_q->produce_mask;
+		emac_reg_update32(adpt->base + rx_q->produce_reg,
+				  rx_q->produce_mask, prod_idx);
+	}
+}
+
+static void emac_adjust_link(struct net_device *netdev)
+{
+	struct emac_adapter *adpt = netdev_priv(netdev);
+	struct phy_device *phydev = netdev->phydev;
+
+	if (phydev->link)
+		emac_mac_start(adpt);
+	else
+		emac_mac_stop(adpt);
+
+	phy_print_status(phydev);
+}
+
+/* Bringup the interface/HW */
+int emac_mac_up(struct emac_adapter *adpt)
+{
+	struct net_device *netdev = adpt->netdev;
+	struct emac_irq	*irq = &adpt->irq;
+	int ret;
+
+	emac_mac_rx_tx_ring_reset_all(adpt);
+	emac_mac_config(adpt);
+
+	ret = request_irq(irq->irq, emac_isr, 0, EMAC_MAC_IRQ_RES, irq);
+	if (ret) {
+		netdev_err(adpt->netdev,
+			   "error:%d on request_irq(%d:%s flags:0)\n", ret,
+			   irq->irq, EMAC_MAC_IRQ_RES);
+		return ret;
+	}
+
+	emac_mac_rx_descs_refill(adpt, &adpt->rx_q);
+
+	ret = phy_connect_direct(netdev, adpt->phydev, emac_adjust_link,
+				 PHY_INTERFACE_MODE_SGMII);
+	if (ret) {
+		netdev_err(adpt->netdev,
+			   "error:%d on request_irq(%d:%s flags:0)\n", ret,
+			   irq->irq, EMAC_MAC_IRQ_RES);
+		free_irq(irq->irq, irq);
+		return ret;
+	}
+
+	/* enable mac irq */
+	writel((u32)~DIS_INT, adpt->base + EMAC_INT_STATUS);
+	writel(adpt->irq.mask, adpt->base + EMAC_INT_MASK);
+
+	adpt->phydev->irq = PHY_IGNORE_INTERRUPT;
+	phy_start(adpt->phydev);
+
+	napi_enable(&adpt->rx_q.napi);
+	netif_start_queue(netdev);
+
+	return 0;
+}
+
+/* Bring down the interface/HW */
+void emac_mac_down(struct emac_adapter *adpt)
+{
+	struct net_device *netdev = adpt->netdev;
+
+	netif_stop_queue(netdev);
+	napi_disable(&adpt->rx_q.napi);
+
+	phy_stop(adpt->phydev);
+	phy_disconnect(adpt->phydev);
+
+	/* disable mac irq */
+	writel(DIS_INT, adpt->base + EMAC_INT_STATUS);
+	writel(0, adpt->base + EMAC_INT_MASK);
+	synchronize_irq(adpt->irq.irq);
+	free_irq(adpt->irq.irq, &adpt->irq);
+
+	emac_mac_reset(adpt);
+
+	emac_tx_q_descs_free(adpt);
+	netdev_reset_queue(adpt->netdev);
+	emac_rx_q_free_descs(adpt);
+}
+
+/* Consume next received packet descriptor */
+static bool emac_rx_process_rrd(struct emac_adapter *adpt,
+				struct emac_rx_queue *rx_q,
+				struct emac_rrd *rrd)
+{
+	u32 *hw_rrd = EMAC_RRD(rx_q, adpt->rrd_size, rx_q->rrd.consume_idx);
+
+	rrd->word[3] = *(hw_rrd + 3);
+
+	if (!RRD_UPDT(rrd))
+		return false;
+
+	rrd->word[4] = 0;
+	rrd->word[5] = 0;
+
+	rrd->word[0] = *(hw_rrd++);
+	rrd->word[1] = *(hw_rrd++);
+	rrd->word[2] = *(hw_rrd++);
+
+	if (unlikely(RRD_NOR(rrd) != 1)) {
+		netdev_err(adpt->netdev,
+			   "error: multi-RFD not support yet! nor:%lu\n",
+			   RRD_NOR(rrd));
+	}
+
+	/* mark rrd as processed */
+	RRD_UPDT_SET(rrd, 0);
+	*hw_rrd = rrd->word[3];
+
+	if (++rx_q->rrd.consume_idx == rx_q->rrd.count)
+		rx_q->rrd.consume_idx = 0;
+
+	return true;
+}
+
+/* Produce new transmit descriptor */
+static bool emac_tx_tpd_create(struct emac_adapter *adpt,
+			       struct emac_tx_queue *tx_q, struct emac_tpd *tpd)
+{
+	u32 *hw_tpd;
+
+	tx_q->tpd.last_produce_idx = tx_q->tpd.produce_idx;
+	hw_tpd = EMAC_TPD(tx_q, adpt->tpd_size, tx_q->tpd.produce_idx);
+
+	if (++tx_q->tpd.produce_idx == tx_q->tpd.count)
+		tx_q->tpd.produce_idx = 0;
+
+	*(hw_tpd++) = tpd->word[0];
+	*(hw_tpd++) = tpd->word[1];
+	*(hw_tpd++) = tpd->word[2];
+	*hw_tpd = tpd->word[3];
+
+	return true;
+}
+
+/* Mark the last transmit descriptor as such (for the transmit packet) */
+static void emac_tx_tpd_mark_last(struct emac_adapter *adpt,
+				  struct emac_tx_queue *tx_q)
+{
+	u32 *hw_tpd =
+		EMAC_TPD(tx_q, adpt->tpd_size, tx_q->tpd.last_produce_idx);
+	u32 tmp_tpd;
+
+	tmp_tpd = *(hw_tpd + 1);
+	tmp_tpd |= EMAC_TPD_LAST_FRAGMENT;
+	*(hw_tpd + 1) = tmp_tpd;
+}
+
+static void emac_rx_rfd_clean(struct emac_rx_queue *rx_q, struct emac_rrd *rrd)
+{
+	struct emac_buffer *rfbuf = rx_q->rfd.rfbuff;
+	u32 consume_idx = RRD_SI(rrd);
+	unsigned int i;
+
+	for (i = 0; i < RRD_NOR(rrd); i++) {
+		rfbuf[consume_idx].skb = NULL;
+		if (++consume_idx == rx_q->rfd.count)
+			consume_idx = 0;
+	}
+
+	rx_q->rfd.consume_idx = consume_idx;
+	rx_q->rfd.process_idx = consume_idx;
+}
+
+/* Push the received skb to upper layers */
+static void emac_receive_skb(struct emac_rx_queue *rx_q,
+			     struct sk_buff *skb,
+			     u16 vlan_tag, bool vlan_flag)
+{
+	if (vlan_flag) {
+		u16 vlan;
+
+		EMAC_TAG_TO_VLAN(vlan_tag, vlan);
+		__vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan);
+	}
+
+	napi_gro_receive(&rx_q->napi, skb);
+}
+
+/* Process receive event */
+void emac_mac_rx_process(struct emac_adapter *adpt, struct emac_rx_queue *rx_q,
+			 int *num_pkts, int max_pkts)
+{
+	u32 proc_idx, hw_consume_idx, num_consume_pkts;
+	struct net_device *netdev  = adpt->netdev;
+	struct emac_buffer *rfbuf;
+	unsigned int count = 0;
+	struct emac_rrd rrd;
+	struct sk_buff *skb;
+	u32 reg;
+
+	reg = readl_relaxed(adpt->base + rx_q->consume_reg);
+
+	hw_consume_idx = (reg & rx_q->consume_mask) >> rx_q->consume_shift;
+	num_consume_pkts = (hw_consume_idx >= rx_q->rrd.consume_idx) ?
+		(hw_consume_idx -  rx_q->rrd.consume_idx) :
+		(hw_consume_idx + rx_q->rrd.count - rx_q->rrd.consume_idx);
+
+	do {
+		if (!num_consume_pkts)
+			break;
+
+		if (!emac_rx_process_rrd(adpt, rx_q, &rrd))
+			break;
+
+		if (likely(RRD_NOR(&rrd) == 1)) {
+			/* good receive */
+			rfbuf = GET_RFD_BUFFER(rx_q, RRD_SI(&rrd));
+			dma_unmap_single(adpt->netdev->dev.parent,
+					 rfbuf->dma_addr, rfbuf->length,
+					 DMA_FROM_DEVICE);
+			rfbuf->dma_addr = 0;
+			skb = rfbuf->skb;
+		} else {
+			netdev_err(adpt->netdev,
+				   "error: multi-RFD not support yet!\n");
+			break;
+		}
+		emac_rx_rfd_clean(rx_q, &rrd);
+		num_consume_pkts--;
+		count++;
+
+		/* Due to a HW issue in L4 check sum detection (UDP/TCP frags
+		 * with DF set are marked as error), drop packets based on the
+		 * error mask rather than the summary bit (ignoring L4F errors)
+		 */
+		if (rrd.word[EMAC_RRD_STATS_DW_IDX] & EMAC_RRD_ERROR) {
+			netif_dbg(adpt, rx_status, adpt->netdev,
+				  "Drop error packet[RRD: 0x%x:0x%x:0x%x:0x%x]\n",
+				  rrd.word[0], rrd.word[1],
+				  rrd.word[2], rrd.word[3]);
+
+			dev_kfree_skb(skb);
+			continue;
+		}
+
+		skb_put(skb, RRD_PKT_SIZE(&rrd) - ETH_FCS_LEN);
+		skb->dev = netdev;
+		skb->protocol = eth_type_trans(skb, skb->dev);
+		if (netdev->features & NETIF_F_RXCSUM)
+			skb->ip_summed = RRD_L4F(&rrd) ?
+					  CHECKSUM_NONE : CHECKSUM_UNNECESSARY;
+		else
+			skb_checksum_none_assert(skb);
+
+		emac_receive_skb(rx_q, skb, (u16)RRD_CVALN_TAG(&rrd),
+				 (bool)RRD_CVTAG(&rrd));
+
+		netdev->last_rx = jiffies;
+		(*num_pkts)++;
+	} while (*num_pkts < max_pkts);
+
+	if (count) {
+		proc_idx = (rx_q->rfd.process_idx << rx_q->process_shft) &
+				rx_q->process_mask;
+		emac_reg_update32(adpt->base + rx_q->process_reg,
+				  rx_q->process_mask, proc_idx);
+		emac_mac_rx_descs_refill(adpt, rx_q);
+	}
+}
+
+/* get the number of free transmit descriptors */
+static unsigned int emac_tpd_num_free_descs(struct emac_tx_queue *tx_q)
+{
+	u32 produce_idx = tx_q->tpd.produce_idx;
+	u32 consume_idx = tx_q->tpd.consume_idx;
+
+	return (consume_idx > produce_idx) ?
+		(consume_idx - produce_idx - 1) :
+		(tx_q->tpd.count + consume_idx - produce_idx - 1);
+}
+
+/* Process transmit event */
+void emac_mac_tx_process(struct emac_adapter *adpt, struct emac_tx_queue *tx_q)
+{
+	u32 reg = readl_relaxed(adpt->base + tx_q->consume_reg);
+	u32 hw_consume_idx, pkts_compl = 0, bytes_compl = 0;
+	struct emac_buffer *tpbuf;
+
+	hw_consume_idx = (reg & tx_q->consume_mask) >> tx_q->consume_shift;
+
+	while (tx_q->tpd.consume_idx != hw_consume_idx) {
+		tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.consume_idx);
+		if (tpbuf->dma_addr) {
+			dma_unmap_single(adpt->netdev->dev.parent,
+					 tpbuf->dma_addr, tpbuf->length,
+					 DMA_TO_DEVICE);
+			tpbuf->dma_addr = 0;
+		}
+
+		if (tpbuf->skb) {
+			pkts_compl++;
+			bytes_compl += tpbuf->skb->len;
+			dev_kfree_skb_irq(tpbuf->skb);
+			tpbuf->skb = NULL;
+		}
+
+		if (++tx_q->tpd.consume_idx == tx_q->tpd.count)
+			tx_q->tpd.consume_idx = 0;
+	}
+
+	netdev_completed_queue(adpt->netdev, pkts_compl, bytes_compl);
+
+	if (netif_queue_stopped(adpt->netdev))
+		if (emac_tpd_num_free_descs(tx_q) > (MAX_SKB_FRAGS + 1))
+			netif_wake_queue(adpt->netdev);
+}
+
+/* Initialize all queue data structures */
+void emac_mac_rx_tx_ring_init_all(struct platform_device *pdev,
+				  struct emac_adapter *adpt)
+{
+	adpt->rx_q.netdev = adpt->netdev;
+
+	adpt->rx_q.produce_reg  = EMAC_MAILBOX_0;
+	adpt->rx_q.produce_mask = RFD0_PROD_IDX_BMSK;
+	adpt->rx_q.produce_shift = RFD0_PROD_IDX_SHFT;
+
+	adpt->rx_q.process_reg  = EMAC_MAILBOX_0;
+	adpt->rx_q.process_mask = RFD0_PROC_IDX_BMSK;
+	adpt->rx_q.process_shft = RFD0_PROC_IDX_SHFT;
+
+	adpt->rx_q.consume_reg  = EMAC_MAILBOX_3;
+	adpt->rx_q.consume_mask = RFD0_CONS_IDX_BMSK;
+	adpt->rx_q.consume_shift = RFD0_CONS_IDX_SHFT;
+
+	adpt->rx_q.irq          = &adpt->irq;
+	adpt->rx_q.intr         = adpt->irq.mask & ISR_RX_PKT;
+
+	adpt->tx_q.produce_reg  = EMAC_MAILBOX_15;
+	adpt->tx_q.produce_mask = NTPD_PROD_IDX_BMSK;
+	adpt->tx_q.produce_shift = NTPD_PROD_IDX_SHFT;
+
+	adpt->tx_q.consume_reg  = EMAC_MAILBOX_2;
+	adpt->tx_q.consume_mask = NTPD_CONS_IDX_BMSK;
+	adpt->tx_q.consume_shift = NTPD_CONS_IDX_SHFT;
+}
+
+/* Fill up transmit descriptors with TSO and Checksum offload information */
+static int emac_tso_csum(struct emac_adapter *adpt,
+			 struct emac_tx_queue *tx_q,
+			 struct sk_buff *skb,
+			 struct emac_tpd *tpd)
+{
+	unsigned int hdr_len;
+	int ret;
+
+	if (skb_is_gso(skb)) {
+		if (skb_header_cloned(skb)) {
+			ret = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+			if (unlikely(ret))
+				return ret;
+		}
+
+		if (skb->protocol == htons(ETH_P_IP)) {
+			u32 pkt_len = ((unsigned char *)ip_hdr(skb) - skb->data)
+				       + ntohs(ip_hdr(skb)->tot_len);
+			if (skb->len > pkt_len)
+				pskb_trim(skb, pkt_len);
+		}
+
+		hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+		if (unlikely(skb->len == hdr_len)) {
+			/* we only need to do csum */
+			netif_warn(adpt, tx_err, adpt->netdev,
+				   "tso not needed for packet with 0 data\n");
+			goto do_csum;
+		}
+
+		if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV4) {
+			ip_hdr(skb)->check = 0;
+			tcp_hdr(skb)->check =
+				~csum_tcpudp_magic(ip_hdr(skb)->saddr,
+						   ip_hdr(skb)->daddr,
+						   0, IPPROTO_TCP, 0);
+			TPD_IPV4_SET(tpd, 1);
+		}
+
+		if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6) {
+			/* ipv6 tso need an extra tpd */
+			struct emac_tpd extra_tpd;
+
+			memset(tpd, 0, sizeof(*tpd));
+			memset(&extra_tpd, 0, sizeof(extra_tpd));
+
+			ipv6_hdr(skb)->payload_len = 0;
+			tcp_hdr(skb)->check =
+				~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
+						 &ipv6_hdr(skb)->daddr,
+						 0, IPPROTO_TCP, 0);
+			TPD_PKT_LEN_SET(&extra_tpd, skb->len);
+			TPD_LSO_SET(&extra_tpd, 1);
+			TPD_LSOV_SET(&extra_tpd, 1);
+			emac_tx_tpd_create(adpt, tx_q, &extra_tpd);
+			TPD_LSOV_SET(tpd, 1);
+		}
+
+		TPD_LSO_SET(tpd, 1);
+		TPD_TCPHDR_OFFSET_SET(tpd, skb_transport_offset(skb));
+		TPD_MSS_SET(tpd, skb_shinfo(skb)->gso_size);
+		return 0;
+	}
+
+do_csum:
+	if (likely(skb->ip_summed == CHECKSUM_PARTIAL)) {
+		unsigned int css, cso;
+
+		cso = skb_transport_offset(skb);
+		if (unlikely(cso & 0x1)) {
+			netdev_err(adpt->netdev,
+				   "error: payload offset should be even\n");
+			return -EINVAL;
+		}
+		css = cso + skb->csum_offset;
+
+		TPD_PAYLOAD_OFFSET_SET(tpd, cso >> 1);
+		TPD_CXSUM_OFFSET_SET(tpd, css >> 1);
+		TPD_CSX_SET(tpd, 1);
+	}
+
+	return 0;
+}
+
+/* Fill up transmit descriptors */
+static void emac_tx_fill_tpd(struct emac_adapter *adpt,
+			     struct emac_tx_queue *tx_q, struct sk_buff *skb,
+			     struct emac_tpd *tpd)
+{
+	unsigned int nr_frags = skb_shinfo(skb)->nr_frags;
+	unsigned int first = tx_q->tpd.produce_idx;
+	unsigned int len = skb_headlen(skb);
+	struct emac_buffer *tpbuf = NULL;
+	unsigned int mapped_len = 0;
+	unsigned int i;
+	int count = 0;
+	int ret;
+
+	/* if Large Segment Offload is (in TCP Segmentation Offload struct) */
+	if (TPD_LSO(tpd)) {
+		mapped_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+
+		tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.produce_idx);
+		tpbuf->length = mapped_len;
+		tpbuf->dma_addr = dma_map_single(adpt->netdev->dev.parent,
+						 skb->data, tpbuf->length,
+						 DMA_TO_DEVICE);
+		ret = dma_mapping_error(adpt->netdev->dev.parent,
+					tpbuf->dma_addr);
+		if (ret)
+			goto error;
+
+		TPD_BUFFER_ADDR_L_SET(tpd, lower_32_bits(tpbuf->dma_addr));
+		TPD_BUFFER_ADDR_H_SET(tpd, upper_32_bits(tpbuf->dma_addr));
+		TPD_BUF_LEN_SET(tpd, tpbuf->length);
+		emac_tx_tpd_create(adpt, tx_q, tpd);
+		count++;
+	}
+
+	if (mapped_len < len) {
+		tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.produce_idx);
+		tpbuf->length = len - mapped_len;
+		tpbuf->dma_addr = dma_map_single(adpt->netdev->dev.parent,
+						 skb->data + mapped_len,
+						 tpbuf->length, DMA_TO_DEVICE);
+		ret = dma_mapping_error(adpt->netdev->dev.parent,
+					tpbuf->dma_addr);
+		if (ret)
+			goto error;
+
+		TPD_BUFFER_ADDR_L_SET(tpd, lower_32_bits(tpbuf->dma_addr));
+		TPD_BUFFER_ADDR_H_SET(tpd, upper_32_bits(tpbuf->dma_addr));
+		TPD_BUF_LEN_SET(tpd, tpbuf->length);
+		emac_tx_tpd_create(adpt, tx_q, tpd);
+		count++;
+	}
+
+	for (i = 0; i < nr_frags; i++) {
+		struct skb_frag_struct *frag;
+
+		frag = &skb_shinfo(skb)->frags[i];
+
+		tpbuf = GET_TPD_BUFFER(tx_q, tx_q->tpd.produce_idx);
+		tpbuf->length = frag->size;
+		tpbuf->dma_addr = dma_map_page(adpt->netdev->dev.parent,
+					       frag->page.p, frag->page_offset,
+					       tpbuf->length, DMA_TO_DEVICE);
+		ret = dma_mapping_error(adpt->netdev->dev.parent,
+					tpbuf->dma_addr);
+		if (ret)
+			goto error;
+
+		TPD_BUFFER_ADDR_L_SET(tpd, lower_32_bits(tpbuf->dma_addr));
+		TPD_BUFFER_ADDR_H_SET(tpd, upper_32_bits(tpbuf->dma_addr));
+		TPD_BUF_LEN_SET(tpd, tpbuf->length);
+		emac_tx_tpd_create(adpt, tx_q, tpd);
+		count++;
+	}
+
+	/* The last tpd */
+	wmb();
+	emac_tx_tpd_mark_last(adpt, tx_q);
+
+	/* The last buffer info contain the skb address,
+	 * so it will be freed after unmap
+	 */
+	tpbuf->skb = skb;
+
+	return;
+
+error:
+	/* One of the memory mappings failed, so undo everything */
+	tx_q->tpd.produce_idx = first;
+
+	while (count--) {
+		tpbuf = GET_TPD_BUFFER(tx_q, first);
+		dma_unmap_page(adpt->netdev->dev.parent, tpbuf->dma_addr,
+			       tpbuf->length, DMA_TO_DEVICE);
+		tpbuf->dma_addr = 0;
+		tpbuf->length = 0;
+
+		if (++first == tx_q->tpd.count)
+			first = 0;
+	}
+
+	dev_kfree_skb(skb);
+}
+
+/* Transmit the packet using specified transmit queue */
+int emac_mac_tx_buf_send(struct emac_adapter *adpt, struct emac_tx_queue *tx_q,
+			 struct sk_buff *skb)
+{
+	struct emac_tpd tpd;
+	u32 prod_idx;
+
+	memset(&tpd, 0, sizeof(tpd));
+
+	if (emac_tso_csum(adpt, tx_q, skb, &tpd) != 0) {
+		dev_kfree_skb_any(skb);
+		return NETDEV_TX_OK;
+	}
+
+	if (skb_vlan_tag_present(skb)) {
+		u16 tag;
+
+		EMAC_VLAN_TO_TAG(skb_vlan_tag_get(skb), tag);
+		TPD_CVLAN_TAG_SET(&tpd, tag);
+		TPD_INSTC_SET(&tpd, 1);
+	}
+
+	if (skb_network_offset(skb) != ETH_HLEN)
+		TPD_TYP_SET(&tpd, 1);
+
+	emac_tx_fill_tpd(adpt, tx_q, skb, &tpd);
+
+	netdev_sent_queue(adpt->netdev, skb->len);
+
+	/* Make sure the are enough free descriptors to hold one
+	 * maximum-sized SKB.  We need one desc for each fragment,
+	 * one for the checksum (emac_tso_csum), one for TSO, and
+	 * and one for the SKB header.
+	 */
+	if (emac_tpd_num_free_descs(tx_q) < (MAX_SKB_FRAGS + 3))
+		netif_stop_queue(adpt->netdev);
+
+	/* update produce idx */
+	prod_idx = (tx_q->tpd.produce_idx << tx_q->produce_shift) &
+		    tx_q->produce_mask;
+	emac_reg_update32(adpt->base + tx_q->produce_reg,
+			  tx_q->produce_mask, prod_idx);
+
+	return NETDEV_TX_OK;
+}
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-mac.h b/drivers/net/ethernet/qualcomm/emac/emac-mac.h
new file mode 100644
index 0000000..e2933b7
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-mac.h
@@ -0,0 +1,250 @@ 
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/* EMAC DMA HW engine uses three rings:
+ * Tx:
+ *   TPD: Transmit Packet Descriptor ring.
+ * Rx:
+ *   RFD: Receive Free Descriptor ring.
+ *     Ring of descriptors with empty buffers to be filled by Rx HW.
+ *   RRD: Receive Return Descriptor ring.
+ *     Ring of descriptors with buffers filled with received data.
+ */
+
+#ifndef _EMAC_HW_H_
+#define _EMAC_HW_H_
+
+/* EMAC_CSR register offsets */
+#define EMAC_EMAC_WRAPPER_CSR1                                0x000000
+#define EMAC_EMAC_WRAPPER_CSR2                                0x000004
+#define EMAC_EMAC_WRAPPER_TX_TS_LO                            0x000104
+#define EMAC_EMAC_WRAPPER_TX_TS_HI                            0x000108
+#define EMAC_EMAC_WRAPPER_TX_TS_INX                           0x00010c
+
+#define EMAC_MAC_IRQ_RES                                    "core0_irq"
+
+/* DMA Order Settings */
+enum emac_dma_order {
+	emac_dma_ord_in = 1,
+	emac_dma_ord_enh = 2,
+	emac_dma_ord_out = 4
+};
+
+enum emac_dma_req_block {
+	emac_dma_req_128 = 0,
+	emac_dma_req_256 = 1,
+	emac_dma_req_512 = 2,
+	emac_dma_req_1024 = 3,
+	emac_dma_req_2048 = 4,
+	emac_dma_req_4096 = 5
+};
+
+/* Returns the value of bits idx...idx+n_bits */
+#define BITS_GET(val, lo, hi) ((le32_to_cpu(val) & GENMASK((hi), (lo))) >> lo)
+#define BITS_SET(val, lo, hi, new_val) \
+	val = cpu_to_le32((le32_to_cpu(val) & (~GENMASK((hi), (lo)))) |	\
+		(((new_val) << (lo)) & GENMASK((hi), (lo))))
+
+/* RRD (Receive Return Descriptor) */
+struct emac_rrd {
+	u32	word[6];
+
+/* number of RFD */
+#define RRD_NOR(rrd)			BITS_GET((rrd)->word[0], 16, 19)
+/* start consumer index of rfd-ring */
+#define RRD_SI(rrd)			BITS_GET((rrd)->word[0], 20, 31)
+/* vlan-tag (CVID, CFI and PRI) */
+#define RRD_CVALN_TAG(rrd)		BITS_GET((rrd)->word[2], 0, 15)
+/* length of the packet */
+#define RRD_PKT_SIZE(rrd)		BITS_GET((rrd)->word[3], 0, 13)
+/* L4(TCP/UDP) checksum failed */
+#define RRD_L4F(rrd)			BITS_GET((rrd)->word[3], 14, 14)
+/* vlan tagged */
+#define RRD_CVTAG(rrd)			BITS_GET((rrd)->word[3], 16, 16)
+/* When set, indicates that the descriptor is updated by the IP core.
+ * When cleared, indicates that the descriptor is invalid.
+ */
+#define RRD_UPDT(rrd)			BITS_GET((rrd)->word[3], 31, 31)
+#define RRD_UPDT_SET(rrd, val)		BITS_SET((rrd)->word[3], 31, 31, val)
+/* timestamp low */
+#define RRD_TS_LOW(rrd)			BITS_GET((rrd)->word[4], 0, 29)
+/* timestamp high */
+#define RRD_TS_HI(rrd)			le32_to_cpu((rrd)->word[5])
+};
+
+/* TPD (Transmit Packet Descriptor) */
+struct emac_tpd {
+	u32				word[4];
+
+/* Number of bytes of the transmit packet. (include 4-byte CRC) */
+#define TPD_BUF_LEN_SET(tpd, val)	BITS_SET((tpd)->word[0], 0, 15, val)
+/* Custom Checksum Offload: When set, ask IP core to offload custom checksum */
+#define TPD_CSX_SET(tpd, val)		BITS_SET((tpd)->word[1], 8, 8, val)
+/* TCP Large Send Offload: When set, ask IP core to do offload TCP Large Send */
+#define TPD_LSO(tpd)			BITS_GET((tpd)->word[1], 12, 12)
+#define TPD_LSO_SET(tpd, val)		BITS_SET((tpd)->word[1], 12, 12, val)
+/*  Large Send Offload Version: When set, indicates this is an LSOv2
+ * (for both IPv4 and IPv6). When cleared, indicates this is an LSOv1
+ * (only for IPv4).
+ */
+#define TPD_LSOV_SET(tpd, val)		BITS_SET((tpd)->word[1], 13, 13, val)
+/* IPv4 packet: When set, indicates this is an  IPv4 packet, this bit is only
+ * for LSOV2 format.
+ */
+#define TPD_IPV4_SET(tpd, val)		BITS_SET((tpd)->word[1], 16, 16, val)
+/* 0: Ethernet   frame (DA+SA+TYPE+DATA+CRC)
+ * 1: IEEE 802.3 frame (DA+SA+LEN+DSAP+SSAP+CTL+ORG+TYPE+DATA+CRC)
+ */
+#define TPD_TYP_SET(tpd, val)		BITS_SET((tpd)->word[1], 17, 17, val)
+/* Low-32bit Buffer Address */
+#define TPD_BUFFER_ADDR_L_SET(tpd, val)	((tpd)->word[2] = cpu_to_le32(val))
+/* CVLAN Tag to be inserted if INS_VLAN_TAG is set, CVLAN TPID based on global
+ * register configuration.
+ */
+#define TPD_CVLAN_TAG_SET(tpd, val)	BITS_SET((tpd)->word[3], 0, 15, val)
+/*  Insert CVlan Tag: When set, ask MAC to insert CVLAN TAG to outgoing packet
+ */
+#define TPD_INSTC_SET(tpd, val)		BITS_SET((tpd)->word[3], 17, 17, val)
+/* High-14bit Buffer Address, So, the 64b-bit address is
+ * {DESC_CTRL_11_TX_DATA_HIADDR[17:0],(register) BUFFER_ADDR_H, BUFFER_ADDR_L}
+ */
+#define TPD_BUFFER_ADDR_H_SET(tpd, val)	BITS_SET((tpd)->word[3], 18, 30, val)
+/* Format D. Word offset from the 1st byte of this packet to start to calculate
+ * the custom checksum.
+ */
+#define TPD_PAYLOAD_OFFSET_SET(tpd, val) BITS_SET((tpd)->word[1], 0, 7, val)
+/*  Format D. Word offset from the 1st byte of this packet to fill the custom
+ * checksum to
+ */
+#define TPD_CXSUM_OFFSET_SET(tpd, val)	BITS_SET((tpd)->word[1], 18, 25, val)
+
+/* Format C. TCP Header offset from the 1st byte of this packet. (byte unit) */
+#define TPD_TCPHDR_OFFSET_SET(tpd, val)	BITS_SET((tpd)->word[1], 0, 7, val)
+/* Format C. MSS (Maximum Segment Size) got from the protocol layer. (byte unit)
+ */
+#define TPD_MSS_SET(tpd, val)		BITS_SET((tpd)->word[1], 18, 30, val)
+/* packet length in ext tpd */
+#define TPD_PKT_LEN_SET(tpd, val)	((tpd)->word[2] = cpu_to_le32(val))
+};
+
+/* emac_ring_header represents a single, contiguous block of DMA space
+ * mapped for the three descriptor rings (tpd, rfd, rrd)
+ */
+struct emac_ring_header {
+	void			*v_addr;	/* virtual address */
+	dma_addr_t		dma_addr;	/* dma address */
+	size_t			size;		/* length in bytes */
+	size_t			used;
+};
+
+/* emac_buffer is wrapper around a pointer to a socket buffer
+ * so a DMA handle can be stored along with the skb
+ */
+struct emac_buffer {
+	struct sk_buff		*skb;		/* socket buffer */
+	u16			length;		/* rx buffer length */
+	dma_addr_t		dma_addr;	/* dma address */
+};
+
+/* receive free descriptor (rfd) ring */
+struct emac_rfd_ring {
+	struct emac_buffer	*rfbuff;
+	u32 __iomem		*v_addr;	/* virtual address */
+	dma_addr_t		dma_addr;	/* dma address */
+	size_t			size;		/* length in bytes */
+	unsigned int		count;		/* number of desc in the ring */
+	unsigned int		produce_idx;
+	unsigned int		process_idx;
+	unsigned int		consume_idx;	/* unused */
+};
+
+/* Receive Return Desciptor (RRD) ring */
+struct emac_rrd_ring {
+	u32 __iomem		*v_addr;	/* virtual address */
+	dma_addr_t		dma_addr;	/* physical address */
+	size_t			size;		/* length in bytes */
+	unsigned int		count;		/* number of desc in the ring */
+	unsigned int		produce_idx;	/* unused */
+	unsigned int		consume_idx;
+};
+
+/* Rx queue */
+struct emac_rx_queue {
+	struct net_device	*netdev;	/* netdev ring belongs to */
+	struct emac_rrd_ring	rrd;
+	struct emac_rfd_ring	rfd;
+	struct napi_struct	napi;
+	struct emac_irq		*irq;
+
+	u32			intr;
+	u32			produce_mask;
+	u32			process_mask;
+	u32			consume_mask;
+
+	u16			produce_reg;
+	u16			process_reg;
+	u16			consume_reg;
+
+	u8			produce_shift;
+	u8			process_shft;
+	u8			consume_shift;
+};
+
+/* Transimit Packet Descriptor (tpd) ring */
+struct emac_tpd_ring {
+	struct emac_buffer	*tpbuff;
+	u32 __iomem		*v_addr;	/* virtual address */
+	dma_addr_t		dma_addr;	/* dma address */
+
+	size_t			size;		/* length in bytes */
+	unsigned int		count;		/* number of desc in the ring */
+	unsigned int		produce_idx;
+	unsigned int		consume_idx;
+	unsigned int		last_produce_idx;
+};
+
+/* Tx queue */
+struct emac_tx_queue {
+	struct emac_tpd_ring	tpd;
+
+	u32			produce_mask;
+	u32			consume_mask;
+
+	u16			max_packets;	/* max packets per interrupt */
+	u16			produce_reg;
+	u16			consume_reg;
+
+	u8			produce_shift;
+	u8			consume_shift;
+};
+
+struct emac_adapter;
+
+int  emac_mac_up(struct emac_adapter *adpt);
+void emac_mac_down(struct emac_adapter *adpt);
+void emac_mac_reset(struct emac_adapter *adpt);
+void emac_mac_start(struct emac_adapter *adpt);
+void emac_mac_stop(struct emac_adapter *adpt);
+void emac_mac_mode_config(struct emac_adapter *adpt);
+void emac_mac_rx_process(struct emac_adapter *adpt, struct emac_rx_queue *rx_q,
+			 int *num_pkts, int max_pkts);
+int emac_mac_tx_buf_send(struct emac_adapter *adpt, struct emac_tx_queue *tx_q,
+			 struct sk_buff *skb);
+void emac_mac_tx_process(struct emac_adapter *adpt, struct emac_tx_queue *tx_q);
+void emac_mac_rx_tx_ring_init_all(struct platform_device *pdev,
+				  struct emac_adapter *adpt);
+int  emac_mac_rx_tx_rings_alloc_all(struct emac_adapter *adpt);
+void emac_mac_rx_tx_rings_free_all(struct emac_adapter *adpt);
+void emac_mac_multicast_addr_clear(struct emac_adapter *adpt);
+void emac_mac_multicast_addr_set(struct emac_adapter *adpt, u8 *addr);
+
+#endif /*_EMAC_HW_H_*/
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-phy.c b/drivers/net/ethernet/qualcomm/emac/emac-phy.c
new file mode 100644
index 0000000..8d4dc32
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-phy.c
@@ -0,0 +1,201 @@ 
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC PHY Controller driver.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+#include <linux/phy.h>
+#include <linux/iopoll.h>
+#include "emac.h"
+#include "emac-mac.h"
+#include "emac-phy.h"
+#include "emac-sgmii.h"
+
+/* EMAC base register offsets */
+#define EMAC_MDIO_CTRL                                        0x001414
+#define EMAC_PHY_STS                                          0x001418
+#define EMAC_MDIO_EX_CTRL                                     0x001440
+
+/* EMAC_MDIO_CTRL */
+#define MDIO_MODE                                              BIT(30)
+#define MDIO_PR                                                BIT(29)
+#define MDIO_AP_EN                                             BIT(28)
+#define MDIO_BUSY                                              BIT(27)
+#define MDIO_CLK_SEL_BMSK                                    0x7000000
+#define MDIO_CLK_SEL_SHFT                                           24
+#define MDIO_START                                             BIT(23)
+#define SUP_PREAMBLE                                           BIT(22)
+#define MDIO_RD_NWR                                            BIT(21)
+#define MDIO_REG_ADDR_BMSK                                    0x1f0000
+#define MDIO_REG_ADDR_SHFT                                          16
+#define MDIO_DATA_BMSK                                          0xffff
+#define MDIO_DATA_SHFT                                               0
+
+/* EMAC_PHY_STS */
+#define PHY_ADDR_BMSK                                         0x1f0000
+#define PHY_ADDR_SHFT                                               16
+
+#define MDIO_CLK_25_4                                                0
+#define MDIO_CLK_25_28                                               7
+
+#define MDIO_WAIT_TIMES                                           1000
+
+#define EMAC_LINK_SPEED_DEFAULT (\
+		EMAC_LINK_SPEED_10_HALF  |\
+		EMAC_LINK_SPEED_10_FULL  |\
+		EMAC_LINK_SPEED_100_HALF |\
+		EMAC_LINK_SPEED_100_FULL |\
+		EMAC_LINK_SPEED_1GB_FULL)
+
+/**
+ * emac_phy_mdio_autopoll_disable() - disable mdio autopoll
+ * @adpt: the emac adapter
+ *
+ * The autopoll feature takes over the MDIO bus.  In order for
+ * the PHY driver to be able to talk to the PHY over the MDIO
+ * bus, we need to temporarily disable the autopoll feature.
+ */
+static int emac_phy_mdio_autopoll_disable(struct emac_adapter *adpt)
+{
+	u32 val;
+
+	/* disable autopoll */
+	emac_reg_update32(adpt->base + EMAC_MDIO_CTRL, MDIO_AP_EN, 0);
+
+	/* wait for any mdio polling to complete */
+	if (!readl_poll_timeout(adpt->base + EMAC_MDIO_CTRL, val,
+				!(val & MDIO_BUSY), 100, MDIO_WAIT_TIMES * 100))
+		return 0;
+
+	/* failed to disable; ensure it is enabled before returning */
+	emac_reg_update32(adpt->base + EMAC_MDIO_CTRL, 0, MDIO_AP_EN);
+
+	return -EBUSY;
+}
+
+/**
+ * emac_phy_mdio_autopoll_disable() - disable mdio autopoll
+ * @adpt: the emac adapter
+ *
+ * The EMAC has the ability to poll the external PHY on the MDIO
+ * bus for link state changes.  This eliminates the need for the
+ * driver to poll the phy.  If if the link state does change,
+ * the EMAC issues an interrupt on behalf of the PHY.
+ */
+static void emac_phy_mdio_autopoll_enable(struct emac_adapter *adpt)
+{
+	emac_reg_update32(adpt->base + EMAC_MDIO_CTRL, 0, MDIO_AP_EN);
+}
+
+static int emac_mdio_read(struct mii_bus *bus, int addr, int regnum)
+{
+	struct emac_adapter *adpt = bus->priv;
+	u32 reg;
+	int ret;
+
+	ret = emac_phy_mdio_autopoll_disable(adpt);
+	if (ret)
+		return ret;
+
+	emac_reg_update32(adpt->base + EMAC_PHY_STS, PHY_ADDR_BMSK,
+			  (addr << PHY_ADDR_SHFT));
+
+	reg = SUP_PREAMBLE |
+	      ((MDIO_CLK_25_4 << MDIO_CLK_SEL_SHFT) & MDIO_CLK_SEL_BMSK) |
+	      ((regnum << MDIO_REG_ADDR_SHFT) & MDIO_REG_ADDR_BMSK) |
+	      MDIO_START | MDIO_RD_NWR;
+
+	writel(reg, adpt->base + EMAC_MDIO_CTRL);
+
+	if (readl_poll_timeout(adpt->base + EMAC_MDIO_CTRL, reg,
+			       !(reg & (MDIO_START | MDIO_BUSY)),
+			       100, MDIO_WAIT_TIMES * 100))
+		ret = -EIO;
+	else
+		ret = (reg >> MDIO_DATA_SHFT) & MDIO_DATA_BMSK;
+
+	emac_phy_mdio_autopoll_enable(adpt);
+
+	return ret;
+}
+
+static int emac_mdio_write(struct mii_bus *bus, int addr, int regnum, u16 val)
+{
+	struct emac_adapter *adpt = bus->priv;
+	u32 reg;
+	int ret;
+
+	ret = emac_phy_mdio_autopoll_disable(adpt);
+	if (ret)
+		return ret;
+
+	emac_reg_update32(adpt->base + EMAC_PHY_STS, PHY_ADDR_BMSK,
+			  (addr << PHY_ADDR_SHFT));
+
+	reg = SUP_PREAMBLE |
+		((MDIO_CLK_25_4 << MDIO_CLK_SEL_SHFT) & MDIO_CLK_SEL_BMSK) |
+		((regnum << MDIO_REG_ADDR_SHFT) & MDIO_REG_ADDR_BMSK) |
+		((val << MDIO_DATA_SHFT) & MDIO_DATA_BMSK) |
+		MDIO_START;
+
+	writel(reg, adpt->base + EMAC_MDIO_CTRL);
+
+	if (readl_poll_timeout(adpt->base + EMAC_MDIO_CTRL, reg,
+			       !(reg & (MDIO_START | MDIO_BUSY)), 100,
+			       MDIO_WAIT_TIMES * 100))
+		ret = -EIO;
+
+	emac_phy_mdio_autopoll_enable(adpt);
+
+	return ret;
+}
+
+/* Read phy configuration and initialize it */
+int emac_phy_config(struct platform_device *pdev, struct emac_adapter *adpt)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct mii_bus *mii_bus;
+	int ret;
+
+	/* Create the mii_bus object for talking to the MDIO bus */
+	adpt->mii_bus = mii_bus = devm_mdiobus_alloc(&pdev->dev);
+	if (!mii_bus)
+		return -ENOMEM;
+
+	mii_bus->name = "emac-mdio";
+	snprintf(mii_bus->id, MII_BUS_ID_SIZE, "%s", pdev->name);
+	mii_bus->read = emac_mdio_read;
+	mii_bus->write = emac_mdio_write;
+	mii_bus->parent = &pdev->dev;
+	mii_bus->priv = adpt;
+
+	ret = of_mdiobus_register(mii_bus, np);
+	if (ret) {
+		dev_err(&pdev->dev, "could not register mdio bus\n");
+		return ret;
+	}
+	adpt->phydev = of_phy_find_device(np);
+
+	if (!adpt->phydev) {
+		dev_err(&pdev->dev, "could not find phy device\n");
+		mdiobus_unregister(mii_bus);
+		return ret;
+	}
+
+	phy_attached_print(adpt->phydev, NULL);
+
+	return emac_sgmii_config(pdev, adpt);
+}
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-phy.h b/drivers/net/ethernet/qualcomm/emac/emac-phy.h
new file mode 100644
index 0000000..8bcc0e5
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-phy.h
@@ -0,0 +1,32 @@ 
+/* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+*
+* This program is free software; you can redistribute it and/or modify
+* it under the terms of the GNU General Public License version 2 and
+* only version 2 as published by the Free Software Foundation.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+* GNU General Public License for more details.
+*/
+
+#ifndef _EMAC_PHY_H_
+#define _EMAC_PHY_H_
+
+/* emac_phy
+ * @base register file base address space.
+ * @digital per-lane digital block
+ * @version the internal phy version
+ */
+struct emac_phy {
+	void __iomem			*base;
+	void __iomem			*digital;
+
+	unsigned int			version;
+};
+
+struct emac_adapter;
+
+int emac_phy_config(struct platform_device *pdev, struct emac_adapter *adpt);
+
+#endif /* _EMAC_PHY_H_ */
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
new file mode 100644
index 0000000..0607554
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.c
@@ -0,0 +1,693 @@ 
+/* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC SGMII Controller driver.
+ */
+
+#include <linux/iopoll.h>
+#include "emac.h"
+#include "emac-mac.h"
+#include "emac-sgmii.h"
+
+/* EMAC_QSERDES register offsets */
+#define EMAC_QSERDES_COM_SYS_CLK_CTRL		0x000000
+#define EMAC_QSERDES_COM_PLL_CNTRL		0x000014
+#define EMAC_QSERDES_COM_PLL_IP_SETI		0x000018
+#define EMAC_QSERDES_COM_PLL_CP_SETI		0x000024
+#define EMAC_QSERDES_COM_PLL_IP_SETP		0x000028
+#define EMAC_QSERDES_COM_PLL_CP_SETP		0x00002c
+#define EMAC_QSERDES_COM_SYSCLK_EN_SEL		0x000038
+#define EMAC_QSERDES_COM_RESETSM_CNTRL		0x000040
+#define EMAC_QSERDES_COM_PLLLOCK_CMP1		0x000044
+#define EMAC_QSERDES_COM_PLLLOCK_CMP2		0x000048
+#define EMAC_QSERDES_COM_PLLLOCK_CMP3		0x00004c
+#define EMAC_QSERDES_COM_PLLLOCK_CMP_EN		0x000050
+#define EMAC_QSERDES_COM_DEC_START1		0x000064
+#define EMAC_QSERDES_COM_DIV_FRAC_START1	0x000098
+#define EMAC_QSERDES_COM_DIV_FRAC_START2	0x00009c
+#define EMAC_QSERDES_COM_DIV_FRAC_START3	0x0000a0
+#define EMAC_QSERDES_COM_DEC_START2		0x0000a4
+#define EMAC_QSERDES_COM_PLL_CRCTRL		0x0000ac
+#define EMAC_QSERDES_COM_RESET_SM		0x0000bc
+#define EMAC_QSERDES_TX_BIST_MODE_LANENO	0x000100
+#define EMAC_QSERDES_TX_TX_EMP_POST1_LVL	0x000108
+#define EMAC_QSERDES_TX_TX_DRV_LVL		0x00010c
+#define EMAC_QSERDES_TX_LANE_MODE		0x000150
+#define EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN	0x000170
+#define EMAC_QSERDES_RX_CDR_CONTROL		0x000200
+#define EMAC_QSERDES_RX_CDR_CONTROL2		0x000210
+#define EMAC_QSERDES_RX_RX_EQ_GAIN12		0x000230
+
+/* EMAC_SGMII register offsets */
+#define EMAC_SGMII_PHY_SERDES_START		0x000000
+#define EMAC_SGMII_PHY_CMN_PWR_CTRL		0x000004
+#define EMAC_SGMII_PHY_RX_PWR_CTRL		0x000008
+#define EMAC_SGMII_PHY_TX_PWR_CTRL		0x00000C
+#define EMAC_SGMII_PHY_LANE_CTRL1		0x000018
+#define EMAC_SGMII_PHY_AUTONEG_CFG2		0x000048
+#define EMAC_SGMII_PHY_CDR_CTRL0		0x000058
+#define EMAC_SGMII_PHY_SPEED_CFG1		0x000074
+#define EMAC_SGMII_PHY_POW_DWN_CTRL0		0x000080
+#define EMAC_SGMII_PHY_RESET_CTRL		0x0000a8
+#define EMAC_SGMII_PHY_IRQ_CMD			0x0000ac
+#define EMAC_SGMII_PHY_INTERRUPT_CLEAR		0x0000b0
+#define EMAC_SGMII_PHY_INTERRUPT_MASK		0x0000b4
+#define EMAC_SGMII_PHY_INTERRUPT_STATUS		0x0000b8
+#define EMAC_SGMII_PHY_RX_CHK_STATUS		0x0000d4
+#define EMAC_SGMII_PHY_AUTONEG0_STATUS		0x0000e0
+#define EMAC_SGMII_PHY_AUTONEG1_STATUS		0x0000e4
+
+/* EMAC_QSERDES_COM_PLL_IP_SETI */
+#define PLL_IPSETI(x)				((x) & 0x3f)
+
+/* EMAC_QSERDES_COM_PLL_CP_SETI */
+#define PLL_CPSETI(x)				((x) & 0xff)
+
+/* EMAC_QSERDES_COM_PLL_IP_SETP */
+#define PLL_IPSETP(x)				((x) & 0x3f)
+
+/* EMAC_QSERDES_COM_PLL_CP_SETP */
+#define PLL_CPSETP(x)				((x) & 0x1f)
+
+/* EMAC_QSERDES_COM_PLL_CRCTRL */
+#define PLL_RCTRL(x)				(((x) & 0xf) << 4)
+#define PLL_CCTRL(x)				((x) & 0xf)
+
+/* SGMII v2 PHY registers per lane */
+#define EMAC_SGMII_PHY_LN_OFFSET		0x0400
+
+/* SGMII v2 digital lane registers */
+#define EMAC_SGMII_LN_DRVR_CTRL0		0x00C
+#define EMAC_SGMII_LN_DRVR_TAP_EN		0x018
+#define EMAC_SGMII_LN_TX_MARGINING		0x01C
+#define EMAC_SGMII_LN_TX_PRE			0x020
+#define EMAC_SGMII_LN_TX_POST			0x024
+#define EMAC_SGMII_LN_TX_BAND_MODE		0x060
+#define EMAC_SGMII_LN_LANE_MODE			0x064
+#define EMAC_SGMII_LN_PARALLEL_RATE		0x078
+#define EMAC_SGMII_LN_CML_CTRL_MODE0		0x0B8
+#define EMAC_SGMII_LN_MIXER_CTRL_MODE0		0x0D0
+#define EMAC_SGMII_LN_VGA_INITVAL		0x134
+#define EMAC_SGMII_LN_UCDR_FO_GAIN_MODE0	0x17C
+#define EMAC_SGMII_LN_UCDR_SO_GAIN_MODE0	0x188
+#define EMAC_SGMII_LN_UCDR_SO_CONFIG		0x194
+#define EMAC_SGMII_LN_RX_BAND			0x19C
+#define EMAC_SGMII_LN_RX_RCVR_PATH1_MODE0	0x1B8
+#define EMAC_SGMII_LN_RSM_CONFIG		0x1F0
+#define EMAC_SGMII_LN_SIGDET_ENABLES		0x224
+#define EMAC_SGMII_LN_SIGDET_CNTRL		0x228
+#define EMAC_SGMII_LN_SIGDET_DEGLITCH_CNTRL	0x22C
+#define EMAC_SGMII_LN_RX_EN_SIGNAL		0x2A0
+#define EMAC_SGMII_LN_RX_MISC_CNTRL0		0x2AC
+#define EMAC_SGMII_LN_DRVR_LOGIC_CLKDIV		0x2BC
+
+/* SGMII v2 digital lane register values */
+#define UCDR_STEP_BY_TWO_MODE0			BIT(7)
+#define UCDR_xO_GAIN_MODE(x)			((x) & 0x7f)
+#define UCDR_ENABLE				BIT(6)
+#define UCDR_SO_SATURATION(x)			((x) & 0x3f)
+#define SIGDET_LP_BYP_PS4			BIT(7)
+#define SIGDET_EN_PS0_TO_PS2			BIT(6)
+#define EN_ACCOUPLEVCM_SW_MUX			BIT(5)
+#define EN_ACCOUPLEVCM_SW			BIT(4)
+#define RX_SYNC_EN				BIT(3)
+#define RXTERM_HIGHZ_PS5			BIT(2)
+#define SIGDET_EN_PS3				BIT(1)
+#define EN_ACCOUPLE_VCM_PS3			BIT(0)
+#define UFS_MODE				BIT(5)
+#define TXVAL_VALID_INIT			BIT(4)
+#define TXVAL_VALID_MUX				BIT(3)
+#define TXVAL_VALID				BIT(2)
+#define USB3P1_MODE				BIT(1)
+#define KR_PCIGEN3_MODE				BIT(0)
+#define PRE_EN					BIT(3)
+#define POST_EN					BIT(2)
+#define MAIN_EN_MUX				BIT(1)
+#define MAIN_EN					BIT(0)
+#define TX_MARGINING_MUX			BIT(6)
+#define TX_MARGINING(x)				((x) & 0x3f)
+#define TX_PRE_MUX				BIT(6)
+#define TX_PRE(x)				((x) & 0x3f)
+#define TX_POST_MUX				BIT(6)
+#define TX_POST(x)				((x) & 0x3f)
+#define CML_GEAR_MODE(x)			(((x) & 7) << 3)
+#define CML2CMOS_IBOOST_MODE(x)			((x) & 7)
+#define MIXER_LOADB_MODE(x)			(((x) & 0xf) << 2)
+#define MIXER_DATARATE_MODE(x)			((x) & 3)
+#define VGA_THRESH_DFE(x)			((x) & 0x3f)
+#define SIGDET_LP_BYP_PS0_TO_PS2		BIT(5)
+#define SIGDET_LP_BYP_MUX			BIT(4)
+#define SIGDET_LP_BYP				BIT(3)
+#define SIGDET_EN_MUX				BIT(2)
+#define SIGDET_EN				BIT(1)
+#define SIGDET_FLT_BYP				BIT(0)
+#define SIGDET_LVL(x)				(((x) & 0xf) << 4)
+#define SIGDET_BW_CTRL(x)			((x) & 0xf)
+#define SIGDET_DEGLITCH_CTRL(x)			(((x) & 0xf) << 1)
+#define SIGDET_DEGLITCH_BYP			BIT(0)
+#define INVERT_PCS_RX_CLK			BIT(7)
+#define PWM_EN					BIT(6)
+#define RXBIAS_SEL(x)				(((x) & 0x3) << 4)
+#define EBDAC_SIGN				BIT(3)
+#define EDAC_SIGN				BIT(2)
+#define EN_AUXTAP1SIGN_INVERT			BIT(1)
+#define EN_DAC_CHOPPING				BIT(0)
+#define DRVR_LOGIC_CLK_EN			BIT(4)
+#define DRVR_LOGIC_CLK_DIV(x)			((x) & 0xf)
+#define PARALLEL_RATE_MODE2(x)			(((x) & 0x3) << 4)
+#define PARALLEL_RATE_MODE1(x)			(((x) & 0x3) << 2)
+#define PARALLEL_RATE_MODE0(x)			((x) & 0x3)
+#define BAND_MODE2(x)				(((x) & 0x3) << 4)
+#define BAND_MODE1(x)				(((x) & 0x3) << 2)
+#define BAND_MODE0(x)				((x) & 0x3)
+#define LANE_SYNC_MODE				BIT(5)
+#define LANE_MODE(x)				((x) & 0x1f)
+#define CDR_PD_SEL_MODE0(x)			(((x) & 0x3) << 5)
+#define EN_DLL_MODE0				BIT(4)
+#define EN_IQ_DCC_MODE0				BIT(3)
+#define EN_IQCAL_MODE0				BIT(2)
+#define EN_QPATH_MODE0				BIT(1)
+#define EN_EPATH_MODE0				BIT(0)
+#define FORCE_TSYNC_ACK				BIT(7)
+#define FORCE_CMN_ACK				BIT(6)
+#define FORCE_CMN_READY				BIT(5)
+#define EN_RCLK_DEGLITCH			BIT(4)
+#define BYPASS_RSM_CDR_RESET			BIT(3)
+#define BYPASS_RSM_TSYNC			BIT(2)
+#define BYPASS_RSM_SAMP_CAL			BIT(1)
+#define BYPASS_RSM_DLL_CAL			BIT(0)
+
+/* EMAC_QSERDES_COM_SYS_CLK_CTRL */
+#define SYSCLK_CM				BIT(4)
+#define SYSCLK_AC_COUPLE			BIT(3)
+
+/* EMAC_QSERDES_COM_PLL_CNTRL */
+#define OCP_EN					BIT(5)
+#define PLL_DIV_FFEN				BIT(2)
+#define PLL_DIV_ORD				BIT(1)
+
+/* EMAC_QSERDES_COM_SYSCLK_EN_SEL */
+#define SYSCLK_SEL_CMOS				BIT(3)
+
+/* EMAC_QSERDES_COM_RESETSM_CNTRL */
+#define FRQ_TUNE_MODE				BIT(4)
+
+/* EMAC_QSERDES_COM_PLLLOCK_CMP_EN */
+#define PLLLOCK_CMP_EN				BIT(0)
+
+/* EMAC_QSERDES_COM_DEC_START1 */
+#define DEC_START1_MUX				BIT(7)
+#define DEC_START1(x)				((x) & 0x7f)
+
+/* EMAC_QSERDES_COM_DIV_FRAC_START1 * EMAC_QSERDES_COM_DIV_FRAC_START2 */
+#define DIV_FRAC_START_MUX			BIT(7)
+#define DIV_FRAC_START(x)			((x) & 0x7f)
+
+/* EMAC_QSERDES_COM_DIV_FRAC_START3 */
+#define DIV_FRAC_START3_MUX			BIT(4)
+#define DIV_FRAC_START3(x)			((x) & 0xf)
+
+/* EMAC_QSERDES_COM_DEC_START2 */
+#define DEC_START2_MUX				BIT(1)
+#define DEC_START2				BIT(0)
+
+/* EMAC_QSERDES_COM_RESET_SM */
+#define READY					BIT(5)
+
+/* EMAC_QSERDES_TX_TX_EMP_POST1_LVL */
+#define TX_EMP_POST1_LVL_MUX			BIT(5)
+#define TX_EMP_POST1_LVL(x)			((x) & 0x1f)
+#define TX_EMP_POST1_LVL_BMSK			0x1f
+#define TX_EMP_POST1_LVL_SHFT			0
+
+/* EMAC_QSERDES_TX_TX_DRV_LVL */
+#define TX_DRV_LVL_MUX				BIT(4)
+#define TX_DRV_LVL(x)				((x) & 0xf)
+
+/* EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN */
+#define EMP_EN_MUX				BIT(1)
+#define EMP_EN					BIT(0)
+
+/* EMAC_QSERDES_RX_CDR_CONTROL & EMAC_QSERDES_RX_CDR_CONTROL2 */
+#define HBW_PD_EN				BIT(7)
+#define SECONDORDERENABLE			BIT(6)
+#define FIRSTORDER_THRESH(x)			(((x) & 0x7) << 3)
+#define SECONDORDERGAIN(x)			((x) & 0x7)
+
+/* EMAC_QSERDES_RX_RX_EQ_GAIN12 */
+#define RX_EQ_GAIN2(x)				(((x) & 0xf) << 4)
+#define RX_EQ_GAIN1(x)				((x) & 0xf)
+
+/* EMAC_SGMII_PHY_SERDES_START */
+#define SERDES_START				BIT(0)
+
+/* EMAC_SGMII_PHY_CMN_PWR_CTRL */
+#define BIAS_EN					BIT(6)
+#define PLL_EN					BIT(5)
+#define SYSCLK_EN				BIT(4)
+#define CLKBUF_L_EN				BIT(3)
+#define PLL_TXCLK_EN				BIT(1)
+#define PLL_RXCLK_EN				BIT(0)
+
+/* EMAC_SGMII_PHY_RX_PWR_CTRL */
+#define L0_RX_SIGDET_EN				BIT(7)
+#define L0_RX_TERM_MODE(x)			(((x) & 3) << 4)
+#define L0_RX_I_EN				BIT(1)
+
+/* EMAC_SGMII_PHY_TX_PWR_CTRL */
+#define L0_TX_EN				BIT(5)
+#define L0_CLKBUF_EN				BIT(4)
+#define L0_TRAN_BIAS_EN				BIT(1)
+
+/* EMAC_SGMII_PHY_LANE_CTRL1 */
+#define L0_RX_EQUALIZE_ENABLE			BIT(6)
+#define L0_RESET_TSYNC_EN			BIT(4)
+#define L0_DRV_LVL(x)				((x) & 0xf)
+
+/* EMAC_SGMII_PHY_AUTONEG_CFG2 */
+#define FORCE_AN_TX_CFG				BIT(5)
+#define FORCE_AN_RX_CFG				BIT(4)
+#define AN_ENABLE				BIT(0)
+
+/* EMAC_SGMII_PHY_SPEED_CFG1 */
+#define DUPLEX_MODE				BIT(4)
+#define SPDMODE_1000				BIT(1)
+#define SPDMODE_100				BIT(0)
+#define SPDMODE_10				0
+#define SPDMODE_BMSK				3
+#define SPDMODE_SHFT				0
+
+/* EMAC_SGMII_PHY_POW_DWN_CTRL0 */
+#define PWRDN_B					BIT(0)
+#define CDR_MAX_CNT(x)				((x) & 0xff)
+
+/* EMAC_QSERDES_TX_BIST_MODE_LANENO */
+#define BIST_LANE_NUMBER(x)			(((x) & 3) << 5)
+#define BISTMODE(x)				((x) & 0x1f)
+
+/* EMAC_QSERDES_COM_PLLLOCK_CMPx */
+#define PLLLOCK_CMP(x)				((x) & 0xff)
+
+/* EMAC_SGMII_PHY_RESET_CTRL */
+#define PHY_SW_RESET				BIT(0)
+
+/* EMAC_SGMII_PHY_IRQ_CMD */
+#define IRQ_GLOBAL_CLEAR			BIT(0)
+
+/* EMAC_SGMII_PHY_INTERRUPT_MASK */
+#define DECODE_CODE_ERR				BIT(7)
+#define DECODE_DISP_ERR				BIT(6)
+#define PLL_UNLOCK				BIT(5)
+#define AN_ILLEGAL_TERM				BIT(4)
+#define SYNC_FAIL				BIT(3)
+#define AN_START				BIT(2)
+#define AN_END					BIT(1)
+#define AN_REQUEST				BIT(0)
+
+#define SGMII_PHY_IRQ_CLR_WAIT_TIME		10
+
+#define SGMII_PHY_INTERRUPT_ERR (\
+	DECODE_CODE_ERR         |\
+	DECODE_DISP_ERR)
+
+#define SGMII_ISR_AN_MASK       (\
+	AN_REQUEST              |\
+	AN_START                |\
+	AN_END                  |\
+	AN_ILLEGAL_TERM         |\
+	PLL_UNLOCK              |\
+	SYNC_FAIL)
+
+#define SGMII_ISR_MASK          (\
+	SGMII_PHY_INTERRUPT_ERR |\
+	SGMII_ISR_AN_MASK)
+
+/* SGMII TX_CONFIG */
+#define TXCFG_LINK					      0x8000
+#define TXCFG_MODE_BMSK					      0x1c00
+#define TXCFG_1000_FULL					      0x1800
+#define TXCFG_100_FULL					      0x1400
+#define TXCFG_100_HALF					      0x0400
+#define TXCFG_10_FULL					      0x1000
+#define TXCFG_10_HALF					      0x0000
+
+#define SERDES_START_WAIT_TIMES					 100
+
+#define SGMII_MEM_RES                                         "sgmii"
+#define SGMII_IRQ_RES                                     "sgmii_irq"
+
+struct emac_reg_write {
+	unsigned int offset;
+	u32 val;
+};
+
+static void emac_reg_write_all(void __iomem *base,
+			       const struct emac_reg_write *itr, size_t size)
+{
+	size_t i;
+
+	for (i = 0; i < size; ++itr, ++i)
+		writel(itr->val, base + itr->offset);
+}
+
+static const struct emac_reg_write physical_coding_sublayer_programming_v1[] = {
+	{EMAC_SGMII_PHY_CDR_CTRL0, CDR_MAX_CNT(15)},
+	{EMAC_SGMII_PHY_POW_DWN_CTRL0, PWRDN_B},
+	{EMAC_SGMII_PHY_CMN_PWR_CTRL,
+		BIAS_EN | SYSCLK_EN | CLKBUF_L_EN | PLL_TXCLK_EN | PLL_RXCLK_EN},
+	{EMAC_SGMII_PHY_TX_PWR_CTRL, L0_TX_EN | L0_CLKBUF_EN | L0_TRAN_BIAS_EN},
+	{EMAC_SGMII_PHY_RX_PWR_CTRL,
+		L0_RX_SIGDET_EN | L0_RX_TERM_MODE(1) | L0_RX_I_EN},
+	{EMAC_SGMII_PHY_CMN_PWR_CTRL,
+		BIAS_EN | PLL_EN | SYSCLK_EN | CLKBUF_L_EN | PLL_TXCLK_EN |
+		PLL_RXCLK_EN},
+	{EMAC_SGMII_PHY_LANE_CTRL1,
+		L0_RX_EQUALIZE_ENABLE | L0_RESET_TSYNC_EN | L0_DRV_LVL(15)},
+};
+
+static const struct emac_reg_write sysclk_refclk_setting[] = {
+	{EMAC_QSERDES_COM_SYSCLK_EN_SEL, SYSCLK_SEL_CMOS},
+	{EMAC_QSERDES_COM_SYS_CLK_CTRL,	SYSCLK_CM | SYSCLK_AC_COUPLE},
+};
+
+static const struct emac_reg_write pll_setting[] = {
+	{EMAC_QSERDES_COM_PLL_IP_SETI, PLL_IPSETI(1)},
+	{EMAC_QSERDES_COM_PLL_CP_SETI, PLL_CPSETI(59)},
+	{EMAC_QSERDES_COM_PLL_IP_SETP, PLL_IPSETP(10)},
+	{EMAC_QSERDES_COM_PLL_CP_SETP, PLL_CPSETP(9)},
+	{EMAC_QSERDES_COM_PLL_CRCTRL, PLL_RCTRL(15) | PLL_CCTRL(11)},
+	{EMAC_QSERDES_COM_PLL_CNTRL, OCP_EN | PLL_DIV_FFEN | PLL_DIV_ORD},
+	{EMAC_QSERDES_COM_DEC_START1, DEC_START1_MUX | DEC_START1(2)},
+	{EMAC_QSERDES_COM_DEC_START2, DEC_START2_MUX | DEC_START2},
+	{EMAC_QSERDES_COM_DIV_FRAC_START1,
+		DIV_FRAC_START_MUX | DIV_FRAC_START(85)},
+	{EMAC_QSERDES_COM_DIV_FRAC_START2,
+		DIV_FRAC_START_MUX | DIV_FRAC_START(42)},
+	{EMAC_QSERDES_COM_DIV_FRAC_START3,
+		DIV_FRAC_START3_MUX | DIV_FRAC_START3(3)},
+	{EMAC_QSERDES_COM_PLLLOCK_CMP1, PLLLOCK_CMP(43)},
+	{EMAC_QSERDES_COM_PLLLOCK_CMP2, PLLLOCK_CMP(104)},
+	{EMAC_QSERDES_COM_PLLLOCK_CMP3, PLLLOCK_CMP(0)},
+	{EMAC_QSERDES_COM_PLLLOCK_CMP_EN, PLLLOCK_CMP_EN},
+	{EMAC_QSERDES_COM_RESETSM_CNTRL, FRQ_TUNE_MODE},
+};
+
+static const struct emac_reg_write cdr_setting[] = {
+	{EMAC_QSERDES_RX_CDR_CONTROL,
+		SECONDORDERENABLE | FIRSTORDER_THRESH(3) | SECONDORDERGAIN(2)},
+	{EMAC_QSERDES_RX_CDR_CONTROL2,
+		SECONDORDERENABLE | FIRSTORDER_THRESH(3) | SECONDORDERGAIN(4)},
+};
+
+static const struct emac_reg_write tx_rx_setting[] = {
+	{EMAC_QSERDES_TX_BIST_MODE_LANENO, 0},
+	{EMAC_QSERDES_TX_TX_DRV_LVL, TX_DRV_LVL_MUX | TX_DRV_LVL(15)},
+	{EMAC_QSERDES_TX_TRAN_DRVR_EMP_EN, EMP_EN_MUX | EMP_EN},
+	{EMAC_QSERDES_TX_TX_EMP_POST1_LVL,
+		TX_EMP_POST1_LVL_MUX | TX_EMP_POST1_LVL(1)},
+	{EMAC_QSERDES_RX_RX_EQ_GAIN12, RX_EQ_GAIN2(15) | RX_EQ_GAIN1(15)},
+	{EMAC_QSERDES_TX_LANE_MODE, LANE_MODE(8)},
+};
+
+static const struct emac_reg_write sgmii_v2_laned[] = {
+	/* CDR Settings */
+	{EMAC_SGMII_LN_UCDR_FO_GAIN_MODE0,
+		UCDR_STEP_BY_TWO_MODE0 | UCDR_xO_GAIN_MODE(10)},
+	{EMAC_SGMII_LN_UCDR_SO_GAIN_MODE0, UCDR_xO_GAIN_MODE(6)},
+	{EMAC_SGMII_LN_UCDR_SO_CONFIG, UCDR_ENABLE | UCDR_SO_SATURATION(12)},
+
+	/* TX/RX Settings */
+	{EMAC_SGMII_LN_RX_EN_SIGNAL, SIGDET_LP_BYP_PS4 | SIGDET_EN_PS0_TO_PS2},
+
+	{EMAC_SGMII_LN_DRVR_CTRL0, TXVAL_VALID_INIT | KR_PCIGEN3_MODE},
+	{EMAC_SGMII_LN_DRVR_TAP_EN, MAIN_EN},
+	{EMAC_SGMII_LN_TX_MARGINING, TX_MARGINING_MUX | TX_MARGINING(25)},
+	{EMAC_SGMII_LN_TX_PRE, TX_PRE_MUX},
+	{EMAC_SGMII_LN_TX_POST, TX_POST_MUX},
+
+	{EMAC_SGMII_LN_CML_CTRL_MODE0,
+		CML_GEAR_MODE(1) | CML2CMOS_IBOOST_MODE(1)},
+	{EMAC_SGMII_LN_MIXER_CTRL_MODE0,
+		MIXER_LOADB_MODE(12) | MIXER_DATARATE_MODE(1)},
+	{EMAC_SGMII_LN_VGA_INITVAL, VGA_THRESH_DFE(31)},
+	{EMAC_SGMII_LN_SIGDET_ENABLES,
+		SIGDET_LP_BYP_PS0_TO_PS2 | SIGDET_FLT_BYP},
+	{EMAC_SGMII_LN_SIGDET_CNTRL, SIGDET_LVL(8)},
+
+	{EMAC_SGMII_LN_SIGDET_DEGLITCH_CNTRL, SIGDET_DEGLITCH_CTRL(4)},
+	{EMAC_SGMII_LN_RX_MISC_CNTRL0, 0},
+	{EMAC_SGMII_LN_DRVR_LOGIC_CLKDIV,
+		DRVR_LOGIC_CLK_EN | DRVR_LOGIC_CLK_DIV(4)},
+
+	{EMAC_SGMII_LN_PARALLEL_RATE, PARALLEL_RATE_MODE0(1)},
+	{EMAC_SGMII_LN_TX_BAND_MODE, BAND_MODE0(2)},
+	{EMAC_SGMII_LN_RX_BAND, BAND_MODE0(3)},
+	{EMAC_SGMII_LN_LANE_MODE, LANE_MODE(26)},
+	{EMAC_SGMII_LN_RX_RCVR_PATH1_MODE0, CDR_PD_SEL_MODE0(3)},
+	{EMAC_SGMII_LN_RSM_CONFIG, BYPASS_RSM_SAMP_CAL | BYPASS_RSM_DLL_CAL},
+};
+
+static const struct emac_reg_write physical_coding_sublayer_programming_v2[] = {
+	{EMAC_SGMII_PHY_POW_DWN_CTRL0, PWRDN_B},
+	{EMAC_SGMII_PHY_CDR_CTRL0, CDR_MAX_CNT(15)},
+	{EMAC_SGMII_PHY_TX_PWR_CTRL, 0},
+	{EMAC_SGMII_PHY_LANE_CTRL1, L0_RX_EQUALIZE_ENABLE},
+};
+
+static int emac_sgmii_link_init(struct emac_adapter *adpt)
+{
+	struct phy_device *phydev = adpt->phydev;
+	struct emac_phy *phy = &adpt->phy;
+	u32 val;
+
+	val = readl(phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+
+	if (phydev->autoneg == AUTONEG_ENABLE) {
+		val &= ~(FORCE_AN_RX_CFG | FORCE_AN_TX_CFG);
+		val |= AN_ENABLE;
+		writel(val, phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+	} else {
+		u32 speed_cfg;
+
+		switch (phydev->speed) {
+		case SPEED_10:
+			speed_cfg = SPDMODE_10;
+			break;
+		case SPEED_100:
+			speed_cfg = SPDMODE_100;
+			break;
+		case SPEED_1000:
+			speed_cfg = SPDMODE_1000;
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		if (phydev->duplex == DUPLEX_FULL)
+			speed_cfg |= DUPLEX_MODE;
+
+		val &= ~AN_ENABLE;
+		writel(speed_cfg, phy->base + EMAC_SGMII_PHY_SPEED_CFG1);
+		writel(val, phy->base + EMAC_SGMII_PHY_AUTONEG_CFG2);
+	}
+
+	return 0;
+}
+
+static int emac_sgmii_irq_clear(struct emac_adapter *adpt, u32 irq_bits)
+{
+	struct emac_phy *phy = &adpt->phy;
+	u32 status;
+
+	writel_relaxed(irq_bits, phy->base + EMAC_SGMII_PHY_INTERRUPT_CLEAR);
+	writel_relaxed(IRQ_GLOBAL_CLEAR, phy->base + EMAC_SGMII_PHY_IRQ_CMD);
+	/* Ensure interrupt clear command is written to HW */
+	wmb();
+
+	/* After set the IRQ_GLOBAL_CLEAR bit, the status clearing must
+	 * be confirmed before clearing the bits in other registers.
+	 * It takes a few cycles for hw to clear the interrupt status.
+	 */
+	if (readl_poll_timeout_atomic(phy->base +
+				      EMAC_SGMII_PHY_INTERRUPT_STATUS,
+				      status, !(status & irq_bits), 1,
+				      SGMII_PHY_IRQ_CLR_WAIT_TIME)) {
+		netdev_err(adpt->netdev,
+			   "error: failed clear SGMII irq: status:0x%x bits:0x%x\n",
+			   status, irq_bits);
+		return -EIO;
+	}
+
+	/* Finalize clearing procedure */
+	writel_relaxed(0, phy->base + EMAC_SGMII_PHY_IRQ_CMD);
+	writel_relaxed(0, phy->base + EMAC_SGMII_PHY_INTERRUPT_CLEAR);
+
+	/* Ensure that clearing procedure finalization is written to HW */
+	wmb();
+
+	return 0;
+}
+
+int emac_sgmii_init_v1(struct emac_adapter *adpt)
+{
+	struct emac_phy *phy = &adpt->phy;
+	unsigned int i;
+	int ret;
+
+	ret = emac_sgmii_link_init(adpt);
+	if (ret)
+		return ret;
+
+	emac_reg_write_all(phy->base, physical_coding_sublayer_programming_v1,
+			   ARRAY_SIZE(physical_coding_sublayer_programming_v1));
+	emac_reg_write_all(phy->base, sysclk_refclk_setting,
+			   ARRAY_SIZE(sysclk_refclk_setting));
+	emac_reg_write_all(phy->base, pll_setting, ARRAY_SIZE(pll_setting));
+	emac_reg_write_all(phy->base, cdr_setting, ARRAY_SIZE(cdr_setting));
+	emac_reg_write_all(phy->base, tx_rx_setting,
+			   ARRAY_SIZE(tx_rx_setting));
+
+	/* Power up the Ser/Des engine */
+	writel(SERDES_START, phy->base + EMAC_SGMII_PHY_SERDES_START);
+
+	for (i = 0; i < SERDES_START_WAIT_TIMES; i++) {
+		if (readl(phy->base + EMAC_QSERDES_COM_RESET_SM) & READY)
+			break;
+		usleep_range(100, 200);
+	}
+
+	if (i == SERDES_START_WAIT_TIMES) {
+		netdev_err(adpt->netdev, "error: ser/des failed to start\n");
+		return -EIO;
+	}
+	/* Mask out all the SGMII Interrupt */
+	writel(0, phy->base + EMAC_SGMII_PHY_INTERRUPT_MASK);
+
+	emac_sgmii_irq_clear(adpt, SGMII_PHY_INTERRUPT_ERR);
+
+	return 0;
+}
+
+int emac_sgmii_init_v2(struct emac_adapter *adpt)
+{
+	struct emac_phy *phy = &adpt->phy;
+	void __iomem *phy_regs = phy->base;
+	void __iomem *laned = phy->digital;
+	unsigned int i;
+	u32 lnstatus;
+	int ret;
+
+	ret = emac_sgmii_link_init(adpt);
+	if (ret)
+		return ret;
+
+	/* PCS lane-x init */
+	emac_reg_write_all(phy->base, physical_coding_sublayer_programming_v2,
+			   ARRAY_SIZE(physical_coding_sublayer_programming_v2));
+
+	/* SGMII lane-x init */
+	emac_reg_write_all(phy->digital,
+			   sgmii_v2_laned, ARRAY_SIZE(sgmii_v2_laned));
+
+	/* Power up PCS and start reset lane state machine */
+
+	writel(0x00, phy_regs + EMAC_SGMII_PHY_RESET_CTRL);
+	writel(0x01, laned + SGMII_LN_RSM_START);
+
+	/* Wait for c_ready assertion */
+	for (i = 0; i < SERDES_START_WAIT_TIMES; i++) {
+		lnstatus = readl(phy_regs + SGMII_PHY_LN_LANE_STATUS);
+		if (lnstatus & 0x02)
+			break;
+		usleep_range(100, 200);
+	}
+
+	if (i == SERDES_START_WAIT_TIMES) {
+		netdev_err(adpt->netdev, "SGMII failed to start\n");
+		return -EIO;
+	}
+
+	/* Disable digital and SERDES loopback */
+	writel(0x0, phy_regs + SGMII_PHY_LN_BIST_GEN0);
+	writel(0x0, phy_regs + SGMII_PHY_LN_BIST_GEN2);
+	writel(0x0, phy_regs + SGMII_PHY_LN_CDR_CTRL1);
+
+	/* Mask out all the SGMII Interrupt */
+	writel(0x0, phy_regs + EMAC_SGMII_PHY_INTERRUPT_MASK);
+
+	emac_sgmii_irq_clear(adpt, SGMII_PHY_INTERRUPT_ERR);
+
+	return 0;
+}
+
+void emac_sgmii_reset_prepare(struct emac_adapter *adpt)
+{
+	struct emac_phy *phy = &adpt->phy;
+	u32 val;
+
+	/* Reset PHY */
+	val = readl(phy->base + EMAC_EMAC_WRAPPER_CSR2);
+	writel(((val & ~PHY_RESET) | PHY_RESET), phy->base +
+	       EMAC_EMAC_WRAPPER_CSR2);
+	/* Ensure phy-reset command is written to HW before the release cmd */
+	msleep(50);
+	val = readl(phy->base + EMAC_EMAC_WRAPPER_CSR2);
+	writel((val & ~PHY_RESET), phy->base + EMAC_EMAC_WRAPPER_CSR2);
+	/* Ensure phy-reset release command is written to HW before initializing
+	 * SGMII
+	 */
+	msleep(50);
+}
+
+void emac_sgmii_reset(struct emac_adapter *adpt)
+{
+	clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 19200000);
+	emac_sgmii_reset_prepare(adpt);
+
+	if (adpt->phy.version == 2)
+		emac_sgmii_init_v2(adpt);
+	else
+		emac_sgmii_init_v1(adpt);
+
+	clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 125000000);
+}
+
+int emac_sgmii_config(struct platform_device *pdev, struct emac_adapter *adpt)
+{
+	struct emac_phy *phy = &adpt->phy;
+	struct resource *res;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, SGMII_MEM_RES);
+
+	phy->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(phy->base))
+		return -ENOMEM;
+
+	if (phy->version == 2) {
+		/* SGMII-v2 controller has two CSRs, one per-lane digital part
+		 * and one per-lane analog part. The PHY regmap is
+		 * compatible to SGMII-v1 controller and will be used in PHY
+		 * common code and digital regmap referenced in SGMII-v2
+		 * specific initialization code.
+		 */
+		/* FIXME: we should be calling ioremap twice, instead of
+		 * doing pointer math.
+		 */
+		phy->digital = phy->base;
+		phy->base += EMAC_SGMII_PHY_LN_OFFSET;
+
+		return emac_sgmii_init_v2(adpt);
+	}
+
+	return emac_sgmii_init_v1(adpt);
+}
+
diff --git a/drivers/net/ethernet/qualcomm/emac/emac-sgmii.h b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
new file mode 100644
index 0000000..ce79212
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac-sgmii.h
@@ -0,0 +1,24 @@ 
+/* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _EMAC_SGMII_H_
+#define _EMAC_SGMII_H_
+
+struct emac_adapter;
+struct platform_device;
+
+int emac_sgmii_init_v1(struct emac_adapter *adpt);
+int emac_sgmii_init_v2(struct emac_adapter *adpt);
+int emac_sgmii_config(struct platform_device *pdev, struct emac_adapter *adpt);
+void emac_sgmii_reset(struct emac_adapter *adpt);
+
+#endif
diff --git a/drivers/net/ethernet/qualcomm/emac/emac.c b/drivers/net/ethernet/qualcomm/emac/emac.c
new file mode 100644
index 0000000..c187ec6
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac.c
@@ -0,0 +1,796 @@ 
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/* Qualcomm Technologies, Inc. EMAC Gigabit Ethernet Driver */
+
+#include <linux/if_ether.h>
+#include <linux/if_vlan.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_device.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include "emac.h"
+#include "emac-mac.h"
+#include "emac-phy.h"
+#include "emac-sgmii.h"
+
+#define EMAC_MSG_DEFAULT (NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK |  \
+		NETIF_MSG_TIMER | NETIF_MSG_IFDOWN | NETIF_MSG_IFUP)
+
+#define EMAC_RRD_SIZE					     4
+/* The RRD size if timestamping is enabled: */
+#define EMAC_TS_RRD_SIZE				     6
+#define EMAC_TPD_SIZE					     4
+#define EMAC_RFD_SIZE					     2
+
+#define REG_MAC_RX_STATUS_BIN		 EMAC_RXMAC_STATC_REG0
+#define REG_MAC_RX_STATUS_END		EMAC_RXMAC_STATC_REG22
+#define REG_MAC_TX_STATUS_BIN		 EMAC_TXMAC_STATC_REG0
+#define REG_MAC_TX_STATUS_END		EMAC_TXMAC_STATC_REG24
+
+#define RXQ0_NUM_RFD_PREF_DEF				     8
+#define TXQ0_NUM_TPD_PREF_DEF				     5
+
+#define EMAC_PREAMBLE_DEF				     7
+
+#define DMAR_DLY_CNT_DEF				    15
+#define DMAW_DLY_CNT_DEF				     4
+
+#define IMR_NORMAL_MASK         (\
+		ISR_ERROR       |\
+		ISR_GPHY_LINK   |\
+		ISR_TX_PKT      |\
+		GPHY_WAKEUP_INT)
+
+#define IMR_EXTENDED_MASK       (\
+		SW_MAN_INT      |\
+		ISR_OVER        |\
+		ISR_ERROR       |\
+		ISR_GPHY_LINK   |\
+		ISR_TX_PKT      |\
+		GPHY_WAKEUP_INT)
+
+#define ISR_TX_PKT      (\
+	TX_PKT_INT      |\
+	TX_PKT_INT1     |\
+	TX_PKT_INT2     |\
+	TX_PKT_INT3)
+
+#define ISR_GPHY_LINK        (\
+	GPHY_LINK_UP_INT     |\
+	GPHY_LINK_DOWN_INT)
+
+#define ISR_OVER        (\
+	RFD0_UR_INT     |\
+	RFD1_UR_INT     |\
+	RFD2_UR_INT     |\
+	RFD3_UR_INT     |\
+	RFD4_UR_INT     |\
+	RXF_OF_INT      |\
+	TXF_UR_INT)
+
+#define ISR_ERROR       (\
+	DMAR_TO_INT     |\
+	DMAW_TO_INT     |\
+	TXQ_TO_INT)
+
+/* in sync with enum emac_clk_id */
+static const char * const emac_clk_name[] = {
+	"axi_clk", "cfg_ahb_clk", "high_speed_clk", "mdio_clk", "tx_clk",
+	"rx_clk", "sys_clk"
+};
+
+void emac_reg_update32(void __iomem *addr, u32 mask, u32 val)
+{
+	u32 data = readl(addr);
+
+	writel(((data & ~mask) | val), addr);
+}
+
+/* reinitialize */
+int emac_reinit_locked(struct emac_adapter *adpt)
+{
+	int ret;
+
+	mutex_lock(&adpt->reset_lock);
+
+	emac_mac_down(adpt);
+	emac_sgmii_reset(adpt);
+	ret = emac_mac_up(adpt);
+
+	mutex_unlock(&adpt->reset_lock);
+
+	return ret;
+}
+
+/* NAPI */
+static int emac_napi_rtx(struct napi_struct *napi, int budget)
+{
+	struct emac_rx_queue *rx_q =
+		container_of(napi, struct emac_rx_queue, napi);
+	struct emac_adapter *adpt = netdev_priv(rx_q->netdev);
+	struct emac_irq *irq = rx_q->irq;
+	int work_done = 0;
+
+	emac_mac_rx_process(adpt, rx_q, &work_done, budget);
+
+	if (work_done < budget) {
+		napi_complete(napi);
+
+		irq->mask |= rx_q->intr;
+		writel(irq->mask, adpt->base + EMAC_INT_MASK);
+	}
+
+	return work_done;
+}
+
+/* Transmit the packet */
+static int emac_start_xmit(struct sk_buff *skb, struct net_device *netdev)
+{
+	struct emac_adapter *adpt = netdev_priv(netdev);
+
+	return emac_mac_tx_buf_send(adpt, &adpt->tx_q, skb);
+}
+
+irqreturn_t emac_isr(int _irq, void *data)
+{
+	struct emac_irq *irq = data;
+	struct emac_adapter *adpt =
+		container_of(irq, struct emac_adapter, irq);
+	struct emac_rx_queue *rx_q = &adpt->rx_q;
+	u32 isr, status;
+
+	/* disable the interrupt */
+	writel(0, adpt->base + EMAC_INT_MASK);
+
+	isr = readl_relaxed(adpt->base + EMAC_INT_STATUS);
+
+	status = isr & irq->mask;
+	if (status == 0)
+		goto exit;
+
+	if (status & ISR_ERROR) {
+		netif_warn(adpt,  intr, adpt->netdev,
+			   "warning: error irq status 0x%lx\n",
+			   status & ISR_ERROR);
+		/* reset MAC */
+		schedule_work(&adpt->work_thread);
+	}
+
+	/* Schedule the napi for receive queue with interrupt
+	 * status bit set
+	 */
+	if (status & rx_q->intr) {
+		if (napi_schedule_prep(&rx_q->napi)) {
+			irq->mask &= ~rx_q->intr;
+			__napi_schedule(&rx_q->napi);
+		}
+	}
+
+	if (status & TX_PKT_INT)
+		emac_mac_tx_process(adpt, &adpt->tx_q);
+
+	if (status & ISR_OVER)
+		net_warn_ratelimited("warning: TX/RX overflow\n");
+
+	/* link event */
+	if (status & ISR_GPHY_LINK)
+		phy_mac_interrupt(adpt->phydev, !!(status & GPHY_LINK_UP_INT));
+
+exit:
+	/* enable the interrupt */
+	writel(irq->mask, adpt->base + EMAC_INT_MASK);
+
+	return IRQ_HANDLED;
+}
+
+/* Configure VLAN tag strip/insert feature */
+static int emac_set_features(struct net_device *netdev,
+			     netdev_features_t features)
+{
+	netdev_features_t changed = features ^ netdev->features;
+	struct emac_adapter *adpt = netdev_priv(netdev);
+
+	/* We only need to reprogram the hardware if the VLAN tag features
+	 * have changed, and if it's already running.
+	 */
+	if (!(changed & (NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX)))
+		return 0;
+
+	if (!netif_running(netdev))
+		return 0;
+
+	/* emac_mac_mode_config() uses netdev->features to configure the EMAC,
+	 * so make sure it's set first.
+	 */
+	netdev->features = features;
+
+	return emac_reinit_locked(adpt);
+}
+
+/* Configure Multicast and Promiscuous modes */
+static void emac_rx_mode_set(struct net_device *netdev)
+{
+	struct emac_adapter *adpt = netdev_priv(netdev);
+	struct netdev_hw_addr *ha;
+
+	emac_mac_mode_config(adpt);
+
+	/* update multicast address filtering */
+	emac_mac_multicast_addr_clear(adpt);
+	netdev_for_each_mc_addr(ha, netdev)
+		emac_mac_multicast_addr_set(adpt, ha->addr);
+}
+
+/* Change the Maximum Transfer Unit (MTU) */
+static int emac_change_mtu(struct net_device *netdev, int new_mtu)
+{
+	unsigned int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
+	struct emac_adapter *adpt = netdev_priv(netdev);
+
+	if ((max_frame < EMAC_MIN_ETH_FRAME_SIZE) ||
+	    (max_frame > EMAC_MAX_ETH_FRAME_SIZE)) {
+		netdev_err(adpt->netdev, "error: invalid MTU setting\n");
+		return -EINVAL;
+	}
+
+	netif_info(adpt, hw, adpt->netdev,
+		   "changing MTU from %d to %d\n", netdev->mtu,
+		   new_mtu);
+	netdev->mtu = new_mtu;
+
+	if (netif_running(netdev))
+		return emac_reinit_locked(adpt);
+
+	return 0;
+}
+
+/* Called when the network interface is made active */
+static int emac_open(struct net_device *netdev)
+{
+	struct emac_adapter *adpt = netdev_priv(netdev);
+	int ret;
+
+	/* allocate rx/tx dma buffer & descriptors */
+	ret = emac_mac_rx_tx_rings_alloc_all(adpt);
+	if (ret) {
+		netdev_err(adpt->netdev, "error allocating rx/tx rings\n");
+		return ret;
+	}
+
+	ret = emac_mac_up(adpt);
+	if (ret) {
+		emac_mac_rx_tx_rings_free_all(adpt);
+		return ret;
+	}
+
+	emac_mac_start(adpt);
+
+	return 0;
+}
+
+/* Called when the network interface is disabled */
+static int emac_close(struct net_device *netdev)
+{
+	struct emac_adapter *adpt = netdev_priv(netdev);
+
+	mutex_lock(&adpt->reset_lock);
+
+	emac_mac_down(adpt);
+	emac_mac_rx_tx_rings_free_all(adpt);
+
+	mutex_unlock(&adpt->reset_lock);
+
+	return 0;
+}
+
+/* Respond to a TX hang */
+static void emac_tx_timeout(struct net_device *netdev)
+{
+	struct emac_adapter *adpt = netdev_priv(netdev);
+
+	schedule_work(&adpt->work_thread);
+}
+
+/* IOCTL support for the interface */
+static int emac_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+{
+	if (!netif_running(netdev))
+		return -EINVAL;
+
+	if (!netdev->phydev)
+		return -ENODEV;
+
+	return phy_mii_ioctl(netdev->phydev, ifr, cmd);
+}
+
+/* Provide network statistics info for the interface */
+static struct rtnl_link_stats64 *emac_get_stats64(struct net_device *netdev,
+						  struct rtnl_link_stats64 *net_stats)
+{
+	struct emac_adapter *adpt = netdev_priv(netdev);
+	unsigned int addr = REG_MAC_RX_STATUS_BIN;
+	struct emac_stats *stats = &adpt->stats;
+	u64 *stats_itr = &adpt->stats.rx_ok;
+	u32 val;
+
+	spin_lock(&stats->lock);
+
+	while (addr <= REG_MAC_RX_STATUS_END) {
+		val = readl_relaxed(adpt->base + addr);
+		*stats_itr += val;
+		stats_itr++;
+		addr += sizeof(u32);
+	}
+
+	/* additional rx status */
+	val = readl_relaxed(adpt->base + EMAC_RXMAC_STATC_REG23);
+	adpt->stats.rx_crc_align += val;
+	val = readl_relaxed(adpt->base + EMAC_RXMAC_STATC_REG24);
+	adpt->stats.rx_jubbers += val;
+
+	/* update tx status */
+	addr = REG_MAC_TX_STATUS_BIN;
+	stats_itr = &adpt->stats.tx_ok;
+
+	while (addr <= REG_MAC_TX_STATUS_END) {
+		val = readl_relaxed(adpt->base + addr);
+		*stats_itr += val;
+		++stats_itr;
+		addr += sizeof(u32);
+	}
+
+	/* additional tx status */
+	val = readl_relaxed(adpt->base + EMAC_TXMAC_STATC_REG25);
+	adpt->stats.tx_col += val;
+
+	/* return parsed statistics */
+	net_stats->rx_packets = stats->rx_ok;
+	net_stats->tx_packets = stats->tx_ok;
+	net_stats->rx_bytes = stats->rx_byte_cnt;
+	net_stats->tx_bytes = stats->tx_byte_cnt;
+	net_stats->multicast = stats->rx_mcast;
+	net_stats->collisions = stats->tx_1_col + stats->tx_2_col * 2 +
+				stats->tx_late_col + stats->tx_abort_col;
+
+	net_stats->rx_errors = stats->rx_frag + stats->rx_fcs_err +
+			       stats->rx_len_err + stats->rx_sz_ov +
+			       stats->rx_align_err;
+	net_stats->rx_fifo_errors = stats->rx_rxf_ov;
+	net_stats->rx_length_errors = stats->rx_len_err;
+	net_stats->rx_crc_errors = stats->rx_fcs_err;
+	net_stats->rx_frame_errors = stats->rx_align_err;
+	net_stats->rx_over_errors = stats->rx_rxf_ov;
+	net_stats->rx_missed_errors = stats->rx_rxf_ov;
+
+	net_stats->tx_errors = stats->tx_late_col + stats->tx_abort_col +
+			       stats->tx_underrun + stats->tx_trunc;
+	net_stats->tx_fifo_errors = stats->tx_underrun;
+	net_stats->tx_aborted_errors = stats->tx_abort_col;
+	net_stats->tx_window_errors = stats->tx_late_col;
+
+	spin_unlock(&stats->lock);
+
+	return net_stats;
+}
+
+static const struct net_device_ops emac_netdev_ops = {
+	.ndo_open		= emac_open,
+	.ndo_stop		= emac_close,
+	.ndo_validate_addr	= eth_validate_addr,
+	.ndo_start_xmit		= emac_start_xmit,
+	.ndo_set_mac_address	= eth_mac_addr,
+	.ndo_change_mtu		= emac_change_mtu,
+	.ndo_do_ioctl		= emac_ioctl,
+	.ndo_tx_timeout		= emac_tx_timeout,
+	.ndo_get_stats64	= emac_get_stats64,
+	.ndo_set_features       = emac_set_features,
+	.ndo_set_rx_mode        = emac_rx_mode_set,
+};
+
+/* Watchdog task routine, called to reinitialize the EMAC */
+static void emac_work_thread(struct work_struct *work)
+{
+	struct emac_adapter *adpt =
+		container_of(work, struct emac_adapter, work_thread);
+
+	emac_reinit_locked(adpt);
+}
+
+/* Initialize various data structures  */
+static void emac_init_adapter(struct emac_adapter *adpt)
+{
+	u32 reg;
+
+	/* descriptors */
+	adpt->tx_desc_cnt = EMAC_DEF_TX_DESCS;
+	adpt->rx_desc_cnt = EMAC_DEF_RX_DESCS;
+
+	/* dma */
+	adpt->dma_order = emac_dma_ord_out;
+	adpt->dmar_block = emac_dma_req_4096;
+	adpt->dmaw_block = emac_dma_req_128;
+	adpt->dmar_dly_cnt = DMAR_DLY_CNT_DEF;
+	adpt->dmaw_dly_cnt = DMAW_DLY_CNT_DEF;
+	adpt->tpd_burst = TXQ0_NUM_TPD_PREF_DEF;
+	adpt->rfd_burst = RXQ0_NUM_RFD_PREF_DEF;
+
+	/* irq moderator */
+	reg = ((EMAC_DEF_RX_IRQ_MOD >> 1) << IRQ_MODERATOR2_INIT_SHFT) |
+	      ((EMAC_DEF_TX_IRQ_MOD >> 1) << IRQ_MODERATOR_INIT_SHFT);
+	adpt->irq_mod = reg;
+
+	/* others */
+	adpt->preamble = EMAC_PREAMBLE_DEF;
+}
+
+static const u8 duuid[] = {
+	0x77, 0x79, 0x60, 0xbf,
+	0x2d, 0xab,
+	0x9d, 0x4b,
+	0x94, 0xf0,
+	0xe1, 0x11, 0x98, 0x01, 0xa2, 0xba
+};
+
+/* Get the clock */
+static int emac_clks_get(struct platform_device *pdev,
+			 struct emac_adapter *adpt)
+{
+	struct clk *clk;
+	unsigned int i;
+
+	for (i = 0; i < EMAC_CLK_CNT; i++) {
+		clk = clk_get(&pdev->dev, emac_clk_name[i]);
+
+		if (IS_ERR(clk)) {
+			netdev_err(adpt->netdev, "error:%ld on clk_get(%s)\n",
+				   PTR_ERR(clk), emac_clk_name[i]);
+
+			while (--i >= 0)
+				if (adpt->clk[i]) {
+					clk_put(adpt->clk[i]);
+					adpt->clk[i] = NULL;
+				}
+			return PTR_ERR(clk);
+		}
+
+		adpt->clk[i] = clk;
+	}
+
+	return 0;
+}
+
+/* Initialize clocks */
+static int emac_clks_phase1_init(struct platform_device *pdev,
+				 struct emac_adapter *adpt)
+{
+	int ret;
+
+	ret = clk_prepare_enable(adpt->clk[EMAC_CLK_AXI]);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(adpt->clk[EMAC_CLK_CFG_AHB]);
+	if (ret)
+		return ret;
+
+	ret = clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 19200000);
+	if (ret)
+		return ret;
+
+	return clk_prepare_enable(adpt->clk[EMAC_CLK_HIGH_SPEED]);
+}
+
+/* Enable clocks; needs emac_clks_phase1_init to be called before */
+static int emac_clks_phase2_init(struct platform_device *pdev,
+				 struct emac_adapter *adpt)
+{
+	int ret;
+
+	ret = clk_set_rate(adpt->clk[EMAC_CLK_TX], 125000000);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(adpt->clk[EMAC_CLK_TX]);
+	if (ret)
+		return ret;
+
+	ret = clk_set_rate(adpt->clk[EMAC_CLK_HIGH_SPEED], 125000000);
+	if (ret)
+		return ret;
+
+	ret = clk_set_rate(adpt->clk[EMAC_CLK_MDIO], 25000000);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(adpt->clk[EMAC_CLK_MDIO]);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(adpt->clk[EMAC_CLK_RX]);
+	if (ret)
+		return ret;
+
+	return clk_prepare_enable(adpt->clk[EMAC_CLK_SYS]);
+}
+
+static void emac_clks_phase1_teardown(struct emac_adapter *adpt)
+{
+	clk_disable_unprepare(adpt->clk[EMAC_CLK_AXI]);
+	clk_disable_unprepare(adpt->clk[EMAC_CLK_CFG_AHB]);
+	clk_disable_unprepare(adpt->clk[EMAC_CLK_HIGH_SPEED]);
+}
+
+static void emac_clks_phase2_teardown(struct emac_adapter *adpt)
+{
+	clk_disable_unprepare(adpt->clk[EMAC_CLK_TX]);
+	clk_disable_unprepare(adpt->clk[EMAC_CLK_MDIO]);
+	clk_disable_unprepare(adpt->clk[EMAC_CLK_RX]);
+	clk_disable_unprepare(adpt->clk[EMAC_CLK_SYS]);
+}
+
+/* Get the resources */
+static int emac_probe_resources(struct platform_device *pdev,
+				struct emac_adapter *adpt)
+{
+	struct device_node *node = pdev->dev.of_node;
+	struct net_device *netdev = adpt->netdev;
+	struct resource *res;
+	const void *maddr;
+	unsigned int i;
+	int ret = 0;
+
+	/* get mac address */
+	maddr = of_get_mac_address(node);
+	if (!maddr)
+		eth_hw_addr_random(netdev);
+	else
+		ether_addr_copy(netdev->dev_addr, maddr);
+
+	ret = platform_get_irq_byname(pdev, EMAC_MAC_IRQ_RES);
+	if (ret)
+		ret = platform_get_irq(pdev, 0);
+
+	if (ret < 0) {
+		netdev_err(adpt->netdev,
+			   "error: missing %s resource\n", EMAC_MAC_IRQ_RES);
+		return ret;
+	}
+	adpt->irq.irq = ret;
+
+	ret = emac_clks_get(pdev, adpt);
+	if (ret)
+		return ret;
+
+	/* get register addresses */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "base");
+
+	adpt->base = devm_ioremap_resource(&pdev->dev, res);
+	if (!adpt->base) {
+		ret = -ENOMEM;
+		goto err_reg_res;
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "csr");
+
+	adpt->csr = devm_ioremap_resource(&pdev->dev, res);
+	if (!adpt->csr) {
+		ret = -ENOMEM;
+		goto err_reg_res;
+	}
+
+	netdev->base_addr = (unsigned long)adpt->base;
+	return 0;
+
+err_reg_res:
+	for (i = 0; i < EMAC_CLK_CNT; i++) {
+		if (adpt->clk[i]) {
+			clk_put(adpt->clk[i]);
+			adpt->clk[i] = NULL;
+		}
+	}
+
+	return ret;
+}
+
+/* Release resources */
+static void emac_release_resources(struct emac_adapter *adpt)
+{
+	unsigned int i;
+
+	for (i = 0; i < EMAC_CLK_CNT; i++)
+		if (adpt->clk[i]) {
+			clk_put(adpt->clk[i]);
+			adpt->clk[i] = NULL;
+		}
+}
+
+static const struct of_device_id emac_dt_match[] = {
+	{
+		.compatible = "qcom,fsm9900-emac",
+		.data = (const void *)1,	/* Internal PHY version 1 */
+	},
+	{
+		.compatible = "qcom,qdf2432-emac",
+		.data = (const void *)2,	/* Internal PHY version 1 */
+	},
+	{}
+};
+
+/* Probe function */
+static int emac_probe(struct platform_device *pdev)
+{
+	const struct of_device_id *match;
+	struct net_device *netdev;
+	struct emac_adapter *adpt;
+	struct emac_phy *phy;
+	u16 devid, revid;
+	u32 reg;
+	int ret;
+
+	/* The EMAC itself is capable of 64-bit DMA, so try that first. */
+	ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+	if (ret) {
+		/* Some platforms may restrict the EMAC's address bus to less
+		 * then the size of DDR. In this case, we need to try a
+		 * smaller mask.  We could try every possible smaller mask,
+		 * but that's overkill.  Instead, just fall to 32-bit, which
+		 * should always work.
+		 */
+		ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+		if (ret) {
+			dev_err(&pdev->dev, "could not set DMA mask\n");
+			return ret;
+		}
+	}
+
+	netdev = alloc_etherdev(sizeof(struct emac_adapter));
+	if (!netdev)
+		return -ENOMEM;
+
+	dev_set_drvdata(&pdev->dev, netdev);
+	SET_NETDEV_DEV(netdev, &pdev->dev);
+
+	adpt = netdev_priv(netdev);
+	adpt->netdev = netdev;
+	adpt->msg_enable = EMAC_MSG_DEFAULT;
+
+	phy = &adpt->phy;
+
+	match = of_match_device(emac_dt_match, &pdev->dev);
+	phy->version = (unsigned int)(unsigned long)match->data;
+
+	mutex_init(&adpt->reset_lock);
+	spin_lock_init(&adpt->stats.lock);
+
+	adpt->irq.mask = RX_PKT_INT0 | IMR_NORMAL_MASK;
+
+	ret = emac_probe_resources(pdev, adpt);
+	if (ret)
+		goto err_undo_netdev;
+
+	/* initialize clocks */
+	ret = emac_clks_phase1_init(pdev, adpt);
+	if (ret)
+		goto err_undo_resources;
+
+	netdev->watchdog_timeo = EMAC_WATCHDOG_TIME;
+	netdev->irq = adpt->irq.irq;
+
+	adpt->rrd_size = EMAC_RRD_SIZE;
+	adpt->tpd_size = EMAC_TPD_SIZE;
+	adpt->rfd_size = EMAC_RFD_SIZE;
+
+	/* init netdev */
+	netdev->netdev_ops = &emac_netdev_ops;
+
+	/* init adapter */
+	emac_init_adapter(adpt);
+
+	/* init phy */
+	ret = emac_phy_config(pdev, adpt);
+	if (ret)
+		goto err_undo_clk_phase1;
+
+	/* enable clocks */
+	ret = emac_clks_phase2_init(pdev, adpt);
+	if (ret)
+		goto err_undo_clk_phase2;
+
+	/* reset mac */
+	emac_mac_reset(adpt);
+
+	/* set hw features */
+	netdev->features = NETIF_F_SG | NETIF_F_HW_CSUM | NETIF_F_RXCSUM |
+			NETIF_F_TSO | NETIF_F_TSO6 | NETIF_F_HW_VLAN_CTAG_RX |
+			NETIF_F_HW_VLAN_CTAG_TX;
+	netdev->hw_features = netdev->features;
+
+	netdev->vlan_features |= NETIF_F_SG | NETIF_F_HW_CSUM |
+				 NETIF_F_TSO | NETIF_F_TSO6;
+
+	INIT_WORK(&adpt->work_thread, emac_work_thread);
+
+	/* Initialize queues */
+	emac_mac_rx_tx_ring_init_all(pdev, adpt);
+
+	netif_napi_add(netdev, &adpt->rx_q.napi, emac_napi_rtx,
+		       NAPI_POLL_WEIGHT);
+
+	ret = register_netdev(netdev);
+	if (ret)
+		goto err_undo_clk_phase2;
+
+	reg =  readl_relaxed(adpt->base + EMAC_DMA_MAS_CTRL);
+	devid = (reg & DEV_ID_NUM_BMSK)  >> DEV_ID_NUM_SHFT;
+	revid = (reg & DEV_REV_NUM_BMSK) >> DEV_REV_NUM_SHFT;
+	reg = readl_relaxed(adpt->base + EMAC_CORE_HW_VERSION);
+
+	netif_info(adpt, probe, netdev,
+		   "hardware id %d.%d, hardware version %d.%d.%d\n",
+		   devid, revid,
+		   (reg & MAJOR_BMSK) >> MAJOR_SHFT,
+		   (reg & MINOR_BMSK) >> MINOR_SHFT,
+		   (reg & STEP_BMSK)  >> STEP_SHFT);
+
+	return 0;
+
+err_undo_clk_phase2:
+	mdiobus_unregister(adpt->mii_bus);
+	emac_clks_phase2_teardown(adpt);
+err_undo_clk_phase1:
+	emac_clks_phase1_teardown(adpt);
+err_undo_resources:
+	emac_release_resources(adpt);
+err_undo_netdev:
+	free_netdev(netdev);
+
+	return ret;
+}
+
+static int emac_remove(struct platform_device *pdev)
+{
+	struct net_device *netdev = dev_get_drvdata(&pdev->dev);
+	struct emac_adapter *adpt = netdev_priv(netdev);
+
+	unregister_netdev(netdev);
+	netif_napi_del(&adpt->rx_q.napi);
+
+	emac_clks_phase2_teardown(adpt);
+	emac_clks_phase1_teardown(adpt);
+	emac_release_resources(adpt);
+
+	mdiobus_unregister(adpt->mii_bus);
+	free_netdev(netdev);
+	dev_set_drvdata(&pdev->dev, NULL);
+
+	return 0;
+}
+
+static struct platform_driver emac_platform_driver = {
+	.probe	= emac_probe,
+	.remove	= emac_remove,
+	.driver = {
+		.owner		= THIS_MODULE,
+		.name		= "qcom-emac",
+		.of_match_table = emac_dt_match,
+	},
+};
+
+module_platform_driver(emac_platform_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:qcom-emac");
diff --git a/drivers/net/ethernet/qualcomm/emac/emac.h b/drivers/net/ethernet/qualcomm/emac/emac.h
new file mode 100644
index 0000000..5078a33
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/emac/emac.h
@@ -0,0 +1,335 @@ 
+/* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _EMAC_H_
+#define _EMAC_H_
+
+#include <linux/irqreturn.h>
+#include <linux/netdevice.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+#include "emac-mac.h"
+#include "emac-phy.h"
+
+/* EMAC base register offsets */
+#define EMAC_DMA_MAS_CTRL                                     0x001400
+#define EMAC_IRQ_MOD_TIM_INIT                                 0x001408
+#define EMAC_BLK_IDLE_STS                                     0x00140c
+#define EMAC_PHY_LINK_DELAY                                   0x00141c
+#define EMAC_SYS_ALIV_CTRL                                    0x001434
+#define EMAC_MAC_IPGIFG_CTRL                                  0x001484
+#define EMAC_MAC_STA_ADDR0                                    0x001488
+#define EMAC_MAC_STA_ADDR1                                    0x00148c
+#define EMAC_HASH_TAB_REG0                                    0x001490
+#define EMAC_HASH_TAB_REG1                                    0x001494
+#define EMAC_MAC_HALF_DPLX_CTRL                               0x001498
+#define EMAC_MAX_FRAM_LEN_CTRL                                0x00149c
+#define EMAC_INT_STATUS                                       0x001600
+#define EMAC_INT_MASK                                         0x001604
+#define EMAC_RXMAC_STATC_REG0                                 0x001700
+#define EMAC_RXMAC_STATC_REG22                                0x001758
+#define EMAC_TXMAC_STATC_REG0                                 0x001760
+#define EMAC_TXMAC_STATC_REG24                                0x0017c0
+#define EMAC_CORE_HW_VERSION                                  0x001974
+#define EMAC_IDT_TABLE0                                       0x001b00
+#define EMAC_RXMAC_STATC_REG23                                0x001bc8
+#define EMAC_RXMAC_STATC_REG24                                0x001bcc
+#define EMAC_TXMAC_STATC_REG25                                0x001bd0
+#define EMAC_INT1_MASK                                        0x001bf0
+#define EMAC_INT1_STATUS                                      0x001bf4
+#define EMAC_INT2_MASK                                        0x001bf8
+#define EMAC_INT2_STATUS                                      0x001bfc
+#define EMAC_INT3_MASK                                        0x001c00
+#define EMAC_INT3_STATUS                                      0x001c04
+
+/* EMAC_DMA_MAS_CTRL */
+#define DEV_ID_NUM_BMSK                                     0x7f000000
+#define DEV_ID_NUM_SHFT                                             24
+#define DEV_REV_NUM_BMSK                                      0xff0000
+#define DEV_REV_NUM_SHFT                                            16
+#define INT_RD_CLR_EN                                           0x4000
+#define IRQ_MODERATOR2_EN                                        0x800
+#define IRQ_MODERATOR_EN                                         0x400
+#define LPW_CLK_SEL                                               0x80
+#define LPW_STATE                                                 0x20
+#define LPW_MODE                                                  0x10
+#define SOFT_RST                                                   0x1
+
+/* EMAC_IRQ_MOD_TIM_INIT */
+#define IRQ_MODERATOR2_INIT_BMSK                            0xffff0000
+#define IRQ_MODERATOR2_INIT_SHFT                                    16
+#define IRQ_MODERATOR_INIT_BMSK                                 0xffff
+#define IRQ_MODERATOR_INIT_SHFT                                      0
+
+/* EMAC_INT_STATUS */
+#define DIS_INT                                                BIT(31)
+#define PTP_INT                                                BIT(30)
+#define RFD4_UR_INT                                            BIT(29)
+#define TX_PKT_INT3                                            BIT(26)
+#define TX_PKT_INT2                                            BIT(25)
+#define TX_PKT_INT1                                            BIT(24)
+#define RX_PKT_INT3                                            BIT(19)
+#define RX_PKT_INT2                                            BIT(18)
+#define RX_PKT_INT1                                            BIT(17)
+#define RX_PKT_INT0                                            BIT(16)
+#define TX_PKT_INT                                             BIT(15)
+#define TXQ_TO_INT                                             BIT(14)
+#define GPHY_WAKEUP_INT                                        BIT(13)
+#define GPHY_LINK_DOWN_INT                                     BIT(12)
+#define GPHY_LINK_UP_INT                                       BIT(11)
+#define DMAW_TO_INT                                            BIT(10)
+#define DMAR_TO_INT                                             BIT(9)
+#define TXF_UR_INT                                              BIT(8)
+#define RFD3_UR_INT                                             BIT(7)
+#define RFD2_UR_INT                                             BIT(6)
+#define RFD1_UR_INT                                             BIT(5)
+#define RFD0_UR_INT                                             BIT(4)
+#define RXF_OF_INT                                              BIT(3)
+#define SW_MAN_INT                                              BIT(2)
+
+/* EMAC_MAILBOX_6 */
+#define RFD2_PROC_IDX_BMSK                                   0xfff0000
+#define RFD2_PROC_IDX_SHFT                                          16
+#define RFD2_PROD_IDX_BMSK                                       0xfff
+#define RFD2_PROD_IDX_SHFT                                           0
+
+/* EMAC_CORE_HW_VERSION */
+#define MAJOR_BMSK                                          0xf0000000
+#define MAJOR_SHFT                                                  28
+#define MINOR_BMSK                                           0xfff0000
+#define MINOR_SHFT                                                  16
+#define STEP_BMSK                                               0xffff
+#define STEP_SHFT                                                    0
+
+/* EMAC_EMAC_WRAPPER_CSR1 */
+#define TX_INDX_FIFO_SYNC_RST                                  BIT(23)
+#define TX_TS_FIFO_SYNC_RST                                    BIT(22)
+#define RX_TS_FIFO2_SYNC_RST                                   BIT(21)
+#define RX_TS_FIFO1_SYNC_RST                                   BIT(20)
+#define TX_TS_ENABLE                                           BIT(16)
+#define DIS_1588_CLKS                                          BIT(11)
+#define FREQ_MODE                                               BIT(9)
+#define ENABLE_RRD_TIMESTAMP                                    BIT(3)
+
+/* EMAC_EMAC_WRAPPER_CSR2 */
+#define HDRIVE_BMSK                                             0x3000
+#define HDRIVE_SHFT                                                 12
+#define SLB_EN                                                  BIT(9)
+#define PLB_EN                                                  BIT(8)
+#define WOL_EN                                                  BIT(3)
+#define PHY_RESET                                               BIT(0)
+
+#define EMAC_DEV_ID                                             0x0040
+
+/* SGMII v2 per lane registers */
+#define SGMII_LN_RSM_START             0x029C
+
+/* SGMII v2 PHY common registers */
+#define SGMII_PHY_CMN_CTRL            0x0408
+#define SGMII_PHY_CMN_RESET_CTRL      0x0410
+
+/* SGMII v2 PHY registers per lane */
+#define SGMII_PHY_LN_OFFSET          0x0400
+#define SGMII_PHY_LN_LANE_STATUS     0x00DC
+#define SGMII_PHY_LN_BIST_GEN0       0x008C
+#define SGMII_PHY_LN_BIST_GEN1       0x0090
+#define SGMII_PHY_LN_BIST_GEN2       0x0094
+#define SGMII_PHY_LN_BIST_GEN3       0x0098
+#define SGMII_PHY_LN_CDR_CTRL1       0x005C
+
+enum emac_clk_id {
+	EMAC_CLK_AXI,
+	EMAC_CLK_CFG_AHB,
+	EMAC_CLK_HIGH_SPEED,
+	EMAC_CLK_MDIO,
+	EMAC_CLK_TX,
+	EMAC_CLK_RX,
+	EMAC_CLK_SYS,
+	EMAC_CLK_CNT
+};
+
+#define EMAC_LINK_SPEED_UNKNOWN                                    0x0
+#define EMAC_LINK_SPEED_10_HALF                                 BIT(0)
+#define EMAC_LINK_SPEED_10_FULL                                 BIT(1)
+#define EMAC_LINK_SPEED_100_HALF                                BIT(2)
+#define EMAC_LINK_SPEED_100_FULL                                BIT(3)
+#define EMAC_LINK_SPEED_1GB_FULL                                BIT(5)
+
+#define EMAC_MAX_SETUP_LNK_CYCLE                                   100
+
+/* Wake On Lan */
+#define EMAC_WOL_PHY                     0x00000001 /* PHY Status Change */
+#define EMAC_WOL_MAGIC                   0x00000002 /* Magic Packet */
+
+struct emac_stats {
+	/* rx */
+	u64 rx_ok;              /* good packets */
+	u64 rx_bcast;           /* good broadcast packets */
+	u64 rx_mcast;           /* good multicast packets */
+	u64 rx_pause;           /* pause packet */
+	u64 rx_ctrl;            /* control packets other than pause frame. */
+	u64 rx_fcs_err;         /* packets with bad FCS. */
+	u64 rx_len_err;         /* packets with length mismatch */
+	u64 rx_byte_cnt;        /* good bytes count (without FCS) */
+	u64 rx_runt;            /* runt packets */
+	u64 rx_frag;            /* fragment count */
+	u64 rx_sz_64;	        /* packets that are 64 bytes */
+	u64 rx_sz_65_127;       /* packets that are 65-127 bytes */
+	u64 rx_sz_128_255;      /* packets that are 128-255 bytes */
+	u64 rx_sz_256_511;      /* packets that are 256-511 bytes */
+	u64 rx_sz_512_1023;     /* packets that are 512-1023 bytes */
+	u64 rx_sz_1024_1518;    /* packets that are 1024-1518 bytes */
+	u64 rx_sz_1519_max;     /* packets that are 1519-MTU bytes*/
+	u64 rx_sz_ov;           /* packets that are >MTU bytes (truncated) */
+	u64 rx_rxf_ov;          /* packets dropped due to RX FIFO overflow */
+	u64 rx_align_err;       /* alignment errors */
+	u64 rx_bcast_byte_cnt;  /* broadcast packets byte count (without FCS) */
+	u64 rx_mcast_byte_cnt;  /* multicast packets byte count (without FCS) */
+	u64 rx_err_addr;        /* packets dropped due to address filtering */
+	u64 rx_crc_align;       /* CRC align errors */
+	u64 rx_jubbers;         /* jubbers */
+
+	/* tx */
+	u64 tx_ok;              /* good packets */
+	u64 tx_bcast;           /* good broadcast packets */
+	u64 tx_mcast;           /* good multicast packets */
+	u64 tx_pause;           /* pause packets */
+	u64 tx_exc_defer;       /* packets with excessive deferral */
+	u64 tx_ctrl;            /* control packets other than pause frame */
+	u64 tx_defer;           /* packets that are deferred. */
+	u64 tx_byte_cnt;        /* good bytes count (without FCS) */
+	u64 tx_sz_64;           /* packets that are 64 bytes */
+	u64 tx_sz_65_127;       /* packets that are 65-127 bytes */
+	u64 tx_sz_128_255;      /* packets that are 128-255 bytes */
+	u64 tx_sz_256_511;      /* packets that are 256-511 bytes */
+	u64 tx_sz_512_1023;     /* packets that are 512-1023 bytes */
+	u64 tx_sz_1024_1518;    /* packets that are 1024-1518 bytes */
+	u64 tx_sz_1519_max;     /* packets that are 1519-MTU bytes */
+	u64 tx_1_col;           /* packets single prior collision */
+	u64 tx_2_col;           /* packets with multiple prior collisions */
+	u64 tx_late_col;        /* packets with late collisions */
+	u64 tx_abort_col;       /* packets aborted due to excess collisions */
+	u64 tx_underrun;        /* packets aborted due to FIFO underrun */
+	u64 tx_rd_eop;          /* count of reads beyond EOP */
+	u64 tx_len_err;         /* packets with length mismatch */
+	u64 tx_trunc;           /* packets truncated due to size >MTU */
+	u64 tx_bcast_byte;      /* broadcast packets byte count (without FCS) */
+	u64 tx_mcast_byte;      /* multicast packets byte count (without FCS) */
+	u64 tx_col;             /* collisions */
+
+	spinlock_t lock;	/* prevent multiple simultaneous readers */
+};
+
+/* RSS hstype Definitions */
+#define EMAC_RSS_HSTYP_IPV4_EN				    0x00000001
+#define EMAC_RSS_HSTYP_TCP4_EN				    0x00000002
+#define EMAC_RSS_HSTYP_IPV6_EN				    0x00000004
+#define EMAC_RSS_HSTYP_TCP6_EN				    0x00000008
+#define EMAC_RSS_HSTYP_ALL_EN (\
+		EMAC_RSS_HSTYP_IPV4_EN   |\
+		EMAC_RSS_HSTYP_TCP4_EN   |\
+		EMAC_RSS_HSTYP_IPV6_EN   |\
+		EMAC_RSS_HSTYP_TCP6_EN)
+
+#define EMAC_VLAN_TO_TAG(_vlan, _tag) \
+		(_tag =  ((((_vlan) >> 8) & 0xFF) | (((_vlan) & 0xFF) << 8)))
+
+#define EMAC_TAG_TO_VLAN(_tag, _vlan) \
+		(_vlan = ((((_tag) >> 8) & 0xFF) | (((_tag) & 0xFF) << 8)))
+
+#define EMAC_DEF_RX_BUF_SIZE					  1536
+#define EMAC_MAX_JUMBO_PKT_SIZE				    (9 * 1024)
+#define EMAC_MAX_TX_OFFLOAD_THRESH			    (9 * 1024)
+
+#define EMAC_MAX_ETH_FRAME_SIZE		       EMAC_MAX_JUMBO_PKT_SIZE
+#define EMAC_MIN_ETH_FRAME_SIZE					    68
+
+#define EMAC_DEF_TX_QUEUES					     1
+#define EMAC_DEF_RX_QUEUES					     1
+
+#define EMAC_MIN_TX_DESCS					   128
+#define EMAC_MIN_RX_DESCS					   128
+
+#define EMAC_MAX_TX_DESCS					 16383
+#define EMAC_MAX_RX_DESCS					  2047
+
+#define EMAC_DEF_TX_DESCS					   512
+#define EMAC_DEF_RX_DESCS					   256
+
+#define EMAC_DEF_RX_IRQ_MOD					   250
+#define EMAC_DEF_TX_IRQ_MOD					   250
+
+#define EMAC_WATCHDOG_TIME				      (5 * HZ)
+
+/* by default check link every 4 seconds */
+#define EMAC_TRY_LINK_TIMEOUT				      (4 * HZ)
+
+/* emac_irq per-device (per-adapter) irq properties.
+ * @irq:	irq number.
+ * @mask	mask to use over status register.
+ */
+struct emac_irq {
+	unsigned int	irq;
+	u32		mask;
+};
+
+/* The device's main data structure */
+struct emac_adapter {
+	struct net_device		*netdev;
+	struct mii_bus			*mii_bus;
+	struct phy_device		*phydev;
+
+	void __iomem			*base;
+	void __iomem			*csr;
+
+	struct emac_phy			phy;
+	struct emac_stats		stats;
+
+	struct emac_irq			irq;
+	struct clk			*clk[EMAC_CLK_CNT];
+
+	/* All Descriptor memory */
+	struct emac_ring_header		ring_header;
+	struct emac_tx_queue		tx_q;
+	struct emac_rx_queue		rx_q;
+	unsigned int			tx_desc_cnt;
+	unsigned int			rx_desc_cnt;
+	unsigned int			rrd_size; /* in quad words */
+	unsigned int			rfd_size; /* in quad words */
+	unsigned int			tpd_size; /* in quad words */
+
+	unsigned int			rxbuf_size;
+
+	/* Ring parameter */
+	u8				tpd_burst;
+	u8				rfd_burst;
+	unsigned int			dmaw_dly_cnt;
+	unsigned int			dmar_dly_cnt;
+	enum emac_dma_req_block		dmar_block;
+	enum emac_dma_req_block		dmaw_block;
+	enum emac_dma_order		dma_order;
+
+	u32				irq_mod;
+	u32				preamble;
+
+	struct work_struct		work_thread;
+
+	u16				msg_enable;
+
+	struct mutex			reset_lock;
+};
+
+int emac_reinit_locked(struct emac_adapter *adpt);
+void emac_reg_update32(void __iomem *addr, u32 mask, u32 val);
+irqreturn_t emac_isr(int irq, void *data);
+
+#endif /* _EMAC_H_ */