@@ -262,6 +262,9 @@ dtb-$(CONFIG_SOC_KEYSTONE) += k2hk-evm.dtb \
k2e-evm.dtb \
k2g-evm.dtb
+dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \
+ at91-sama5d2_xplained.dtb
+
targets += $(dtb-y)
# Add any required device tree compiler flags here
new file mode 100644
@@ -0,0 +1,200 @@
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+
+/ {
+ model = "Atmel SAMA5D2 Xplained";
+ compatible = "atmel,sama5d2-xplained", "atmel,sama5d2", "atmel,sama5";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ ahb {
+ usb1: ohci@00400000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <&pioA 42 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+ };
+
+ usb2: ehci@00500000 {
+ status = "okay";
+ };
+
+ sdmmc0: sdio-host@a0000000 {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_cmd_dat_default &pinctrl_sdmmc0_ck_cd_default>;
+ status = "okay";
+ };
+
+ sdmmc1: sdio-host@b0000000 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc1_cmd_dat_default &pinctrl_sdmmc1_ck_cd_default>;
+ status = "okay"; /* conflict with qspi0 */
+ };
+
+ apb {
+ qspi0: spi@f0020000 {
+ status = "okay";
+
+ flash@0 {
+ compatible = "atmel,sama5d2-qspi-flash";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi0_default>;
+ spi-max-frequency = <83000000>;
+
+ partition@00000000 {
+ label = "boot";
+ reg = <0x00000000 0x00c00000>;
+ };
+
+ partition@00c00000 {
+ label = "rootfs";
+ reg = <0x00c00000 0x00000000>;
+ };
+ };
+ };
+
+ spi0: spi@f8000000 {
+ cs-gpios = <&pioA 17 0>, <0>, <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0_default>;
+ status = "okay";
+
+ spi_flash@0 {
+ compatible = "spi-flash";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+ };
+
+ macb0: ethernet@f8008000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
+ phy-mode = "rmii";
+ status = "okay";
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ };
+ };
+
+ uart1: serial@f8020000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+ status = "okay";
+ };
+
+ i2c1: i2c@fc028000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ status = "okay";
+ };
+
+ pioA: gpio@fc038000 {
+ pinctrl {
+ pinctrl_i2c1_default: i2c1_default {
+ pinmux = <PIN_PD4__TWD1>,
+ <PIN_PD5__TWCK1>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ pinmux = <PIN_PC9__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_rmii: macb0_rmii {
+ pinmux = <PIN_PB14__GTXCK>,
+ <PIN_PB15__GTXEN>,
+ <PIN_PB16__GRXDV>,
+ <PIN_PB17__GRXER>,
+ <PIN_PB18__GRX0>,
+ <PIN_PB19__GRX1>,
+ <PIN_PB20__GTX0>,
+ <PIN_PB21__GTX1>,
+ <PIN_PB22__GMDC>,
+ <PIN_PB23__GMDIO>;
+ bias-disable;
+ };
+
+ pinctrl_qspi0_default: qspi0_default {
+ pinmux = <PIN_PA22__QSPI0_SCK>,
+ <PIN_PA23__QSPI0_CS>,
+ <PIN_PA24__QSPI0_IO0>,
+ <PIN_PA25__QSPI0_IO1>,
+ <PIN_PA26__QSPI0_IO2>,
+ <PIN_PA27__QSPI0_IO3>;
+ bias-disable;
+ };
+
+ pinctrl_sdmmc0_cmd_dat_default: sdmmc0_cmd_dat_default {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA2__SDMMC0_DAT0>,
+ <PIN_PA3__SDMMC0_DAT1>,
+ <PIN_PA4__SDMMC0_DAT2>,
+ <PIN_PA5__SDMMC0_DAT3>,
+ <PIN_PA6__SDMMC0_DAT4>,
+ <PIN_PA7__SDMMC0_DAT5>,
+ <PIN_PA8__SDMMC0_DAT6>,
+ <PIN_PA9__SDMMC0_DAT7>;
+ bias-pull-up;
+ };
+
+ pinctrl_sdmmc0_ck_cd_default: sdmmc0_ck_cd_default {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA10__SDMMC0_RSTN>,
+ <PIN_PA11__SDMMC0_VDDSEL>,
+ <PIN_PA13__SDMMC0_CD>;
+ bias-disable;
+ };
+
+ pinctrl_sdmmc1_cmd_dat_default: sdmmc1_cmd_dat_default {
+ pinmux = <PIN_PA28__SDMMC1_CMD>,
+ <PIN_PA18__SDMMC1_DAT0>,
+ <PIN_PA19__SDMMC1_DAT1>,
+ <PIN_PA20__SDMMC1_DAT2>,
+ <PIN_PA21__SDMMC1_DAT3>;
+ bias-pull-up;
+ };
+
+ pinctrl_sdmmc1_ck_cd_default: sdmmc1_ck_cd_default {
+ pinmux = <PIN_PA22__SDMMC1_CK>,
+ <PIN_PA30__SDMMC1_CD>;
+ bias-disable;
+ };
+
+ pinctrl_spi0_default: spi0_default {
+ pinmux = <PIN_PA14__SPI0_SPCK>,
+ <PIN_PA15__SPI0_MOSI>,
+ <PIN_PA16__SPI0_MISO>;
+ bias-disable;
+ };
+
+ pinctrl_uart1_default: uart1_default {
+ pinmux = <PIN_PD2__URXD1>,
+ <PIN_PD3__UTXD1>;
+ bias-disable;
+ };
+
+ pinctrl_usb_default: usb_default {
+ pinmux = <PIN_PB10__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ pinmux = <PIN_PA31__GPIO>;
+ bias-disable;
+ };
+ };
+ };
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,671 @@
+#include "skeleton.dtsi"
+
+/ {
+ model = "Atmel SAMA5D2 family SoC";
+ compatible = "atmel,sama5d2";
+
+ aliases {
+ spi0 = &spi0;
+ spi1 = &qspi0;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ };
+
+ clocks {
+ slow_xtal: slow_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ main_xtal: main_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ usb1: ohci@00400000 {
+ compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+ reg = <0x00400000 0x100000>;
+ clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+ clock-names = "ohci_clk", "hclk", "uhpck";
+ status = "disabled";
+ };
+
+ usb2: ehci@00500000 {
+ compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
+ reg = <0x00500000 0x100000>;
+ clocks = <&utmi>, <&uhphs_clk>;
+ clock-names = "usb_clk", "ehci_clk";
+ status = "disabled";
+ };
+
+ sdmmc0: sdio-host@a0000000 {
+ compatible = "atmel,sama5d2-sdhci";
+ reg = <0xa0000000 0x300>;
+ clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>;
+ clock-names = "hclock", "multclk", "baseclk";
+ status = "disabled";
+ };
+
+ sdmmc1: sdio-host@b0000000 {
+ compatible = "atmel,sama5d2-sdhci";
+ reg = <0xb0000000 0x300>;
+ clocks = <&sdmmc1_hclk>, <&sdmmc1_gclk>, <&main>;
+ clock-names = "hclock", "multclk", "baseclk";
+ status = "disabled";
+ };
+
+ apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ pmc: pmc@f0014000 {
+ compatible = "atmel,sama5d2-pmc", "syscon";
+ reg = <0xf0014000 0x160>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+
+ main: mainck {
+ compatible = "atmel,at91sam9x5-clk-main";
+ #clock-cells = <0>;
+ };
+
+ plla: pllack {
+ compatible = "atmel,sama5d3-clk-pll";
+ #clock-cells = <0>;
+ clocks = <&main>;
+ reg = <0>;
+ atmel,clk-input-range = <12000000 12000000>;
+ #atmel,pll-clk-output-range-cells = <4>;
+ atmel,pll-clk-output-ranges = <600000000 1200000000 0 0>;
+ };
+
+ plladiv: plladivck {
+ compatible = "atmel,at91sam9x5-clk-plldiv";
+ #clock-cells = <0>;
+ clocks = <&plla>;
+ };
+
+ audio_pll_frac: audiopll_fracck {
+ compatible = "atmel,sama5d2-clk-audio-pll-frac";
+ #clock-cells = <0>;
+ clocks = <&main>;
+ };
+
+ audio_pll_pad: audiopll_padck {
+ compatible = "atmel,sama5d2-clk-audio-pll-pad";
+ #clock-cells = <0>;
+ clocks = <&audio_pll_frac>;
+ };
+
+ audio_pll_pmc: audiopll_pmcck {
+ compatible = "atmel,sama5d2-clk-audio-pll-pmc";
+ #clock-cells = <0>;
+ clocks = <&audio_pll_frac>;
+ };
+
+ utmi: utmick {
+ compatible = "atmel,at91sam9x5-clk-utmi";
+ #clock-cells = <0>;
+ clocks = <&main>;
+ };
+
+ mck: masterck {
+ compatible = "atmel,at91sam9x5-clk-master";
+ #clock-cells = <0>;
+ clocks = <&main>, <&plladiv>, <&utmi>;
+ atmel,clk-output-range = <124000000 166000000>;
+ atmel,clk-divisors = <1 2 4 3>;
+ };
+
+ h32ck: h32mxck {
+ #clock-cells = <0>;
+ compatible = "atmel,sama5d4-clk-h32mx";
+ clocks = <&mck>;
+ };
+
+ usb: usbck {
+ compatible = "atmel,at91sam9x5-clk-usb";
+ #clock-cells = <0>;
+ clocks = <&plladiv>, <&utmi>;
+ };
+
+ prog: progck {
+ compatible = "atmel,at91sam9x5-clk-programmable";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&pmc>;
+ clocks = <&main>, <&plladiv>, <&utmi>, <&mck>;
+
+ prog0: prog0 {
+ #clock-cells = <0>;
+ reg = <0>;
+ };
+
+ prog1: prog1 {
+ #clock-cells = <0>;
+ reg = <1>;
+ };
+
+ prog2: prog2 {
+ #clock-cells = <0>;
+ reg = <2>;
+ };
+ };
+
+ systemck {
+ compatible = "atmel,at91rm9200-clk-system";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ddrck: ddrck {
+ #clock-cells = <0>;
+ reg = <2>;
+ clocks = <&mck>;
+ };
+
+ lcdck: lcdck {
+ #clock-cells = <0>;
+ reg = <3>;
+ clocks = <&mck>;
+ };
+
+ uhpck: uhpck {
+ #clock-cells = <0>;
+ reg = <6>;
+ clocks = <&usb>;
+ };
+
+ udpck: udpck {
+ #clock-cells = <0>;
+ reg = <7>;
+ clocks = <&usb>;
+ };
+
+ pck0: pck0 {
+ #clock-cells = <0>;
+ reg = <8>;
+ clocks = <&prog0>;
+ };
+
+ pck1: pck1 {
+ #clock-cells = <0>;
+ reg = <9>;
+ clocks = <&prog1>;
+ };
+
+ pck2: pck2 {
+ #clock-cells = <0>;
+ reg = <10>;
+ clocks = <&prog2>;
+ };
+
+ iscck: iscck {
+ #clock-cells = <0>;
+ reg = <18>;
+ clocks = <&mck>;
+ };
+ };
+
+ periph32ck {
+ compatible = "atmel,at91sam9x5-clk-peripheral";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&h32ck>;
+
+ macb0_clk: macb0_clk {
+ #clock-cells = <0>;
+ reg = <5>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ tdes_clk: tdes_clk {
+ #clock-cells = <0>;
+ reg = <11>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ matrix1_clk: matrix1_clk {
+ #clock-cells = <0>;
+ reg = <14>;
+ };
+
+ hsmc_clk: hsmc_clk {
+ #clock-cells = <0>;
+ reg = <17>;
+ };
+
+ pioA_clk: pioA_clk {
+ #clock-cells = <0>;
+ reg = <18>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ flx0_clk: flx0_clk {
+ #clock-cells = <0>;
+ reg = <19>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ flx1_clk: flx1_clk {
+ #clock-cells = <0>;
+ reg = <20>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ flx2_clk: flx2_clk {
+ #clock-cells = <0>;
+ reg = <21>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ flx3_clk: flx3_clk {
+ #clock-cells = <0>;
+ reg = <22>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ flx4_clk: flx4_clk {
+ #clock-cells = <0>;
+ reg = <23>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ uart0_clk: uart0_clk {
+ #clock-cells = <0>;
+ reg = <24>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ uart1_clk: uart1_clk {
+ #clock-cells = <0>;
+ reg = <25>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ uart2_clk: uart2_clk {
+ #clock-cells = <0>;
+ reg = <26>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ uart3_clk: uart3_clk {
+ #clock-cells = <0>;
+ reg = <27>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ uart4_clk: uart4_clk {
+ #clock-cells = <0>;
+ reg = <28>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ twi0_clk: twi0_clk {
+ reg = <29>;
+ #clock-cells = <0>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ twi1_clk: twi1_clk {
+ #clock-cells = <0>;
+ reg = <30>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ spi0_clk: spi0_clk {
+ #clock-cells = <0>;
+ reg = <33>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ spi1_clk: spi1_clk {
+ #clock-cells = <0>;
+ reg = <34>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ tcb0_clk: tcb0_clk {
+ #clock-cells = <0>;
+ reg = <35>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ tcb1_clk: tcb1_clk {
+ #clock-cells = <0>;
+ reg = <36>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ pwm_clk: pwm_clk {
+ #clock-cells = <0>;
+ reg = <38>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ adc_clk: adc_clk {
+ #clock-cells = <0>;
+ reg = <40>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ uhphs_clk: uhphs_clk {
+ #clock-cells = <0>;
+ reg = <41>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ udphs_clk: udphs_clk {
+ #clock-cells = <0>;
+ reg = <42>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ ssc0_clk: ssc0_clk {
+ #clock-cells = <0>;
+ reg = <43>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ ssc1_clk: ssc1_clk {
+ #clock-cells = <0>;
+ reg = <44>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ trng_clk: trng_clk {
+ #clock-cells = <0>;
+ reg = <47>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ pdmic_clk: pdmic_clk {
+ #clock-cells = <0>;
+ reg = <48>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ i2s0_clk: i2s0_clk {
+ #clock-cells = <0>;
+ reg = <54>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ i2s1_clk: i2s1_clk {
+ #clock-cells = <0>;
+ reg = <55>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ can0_clk: can0_clk {
+ #clock-cells = <0>;
+ reg = <56>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ can1_clk: can1_clk {
+ #clock-cells = <0>;
+ reg = <57>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ classd_clk: classd_clk {
+ #clock-cells = <0>;
+ reg = <59>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+ };
+
+ periph64ck {
+ compatible = "atmel,at91sam9x5-clk-peripheral";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&mck>;
+
+ dma0_clk: dma0_clk {
+ #clock-cells = <0>;
+ reg = <6>;
+ };
+
+ dma1_clk: dma1_clk {
+ #clock-cells = <0>;
+ reg = <7>;
+ };
+
+ aes_clk: aes_clk {
+ #clock-cells = <0>;
+ reg = <9>;
+ };
+
+ aesb_clk: aesb_clk {
+ #clock-cells = <0>;
+ reg = <10>;
+ };
+
+ sha_clk: sha_clk {
+ #clock-cells = <0>;
+ reg = <12>;
+ };
+
+ mpddr_clk: mpddr_clk {
+ #clock-cells = <0>;
+ reg = <13>;
+ };
+
+ matrix0_clk: matrix0_clk {
+ #clock-cells = <0>;
+ reg = <15>;
+ };
+
+ sdmmc0_hclk: sdmmc0_hclk {
+ #clock-cells = <0>;
+ reg = <31>;
+ };
+
+ sdmmc1_hclk: sdmmc1_hclk {
+ #clock-cells = <0>;
+ reg = <32>;
+ };
+
+ lcdc_clk: lcdc_clk {
+ #clock-cells = <0>;
+ reg = <45>;
+ };
+
+ isc_clk: isc_clk {
+ #clock-cells = <0>;
+ reg = <46>;
+ };
+
+ qspi0_clk: qspi0_clk {
+ #clock-cells = <0>;
+ reg = <52>;
+ };
+
+ qspi1_clk: qspi1_clk {
+ #clock-cells = <0>;
+ reg = <53>;
+ };
+ };
+
+ gck {
+ compatible = "atmel,sama5d2-clk-generated";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&pmc>;
+ clocks = <&main>, <&plla>, <&utmi>, <&mck>;
+
+ sdmmc0_gclk: sdmmc0_gclk {
+ #clock-cells = <0>;
+ reg = <31>;
+ };
+
+ sdmmc1_gclk: sdmmc1_gclk {
+ #clock-cells = <0>;
+ reg = <32>;
+ };
+
+ tcb0_gclk: tcb0_gclk {
+ #clock-cells = <0>;
+ reg = <35>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ tcb1_gclk: tcb1_gclk {
+ #clock-cells = <0>;
+ reg = <36>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ pwm_gclk: pwm_gclk {
+ #clock-cells = <0>;
+ reg = <38>;
+ atmel,clk-output-range = <0 83000000>;
+ };
+
+ pdmic_gclk: pdmic_gclk {
+ #clock-cells = <0>;
+ reg = <48>;
+ };
+
+ i2s0_gclk: i2s0_gclk {
+ #clock-cells = <0>;
+ reg = <54>;
+ };
+
+ i2s1_gclk: i2s1_gclk {
+ #clock-cells = <0>;
+ reg = <55>;
+ };
+
+ can0_gclk: can0_gclk {
+ #clock-cells = <0>;
+ reg = <56>;
+ atmel,clk-output-range = <0 80000000>;
+ };
+
+ can1_gclk: can1_gclk {
+ #clock-cells = <0>;
+ reg = <57>;
+ atmel,clk-output-range = <0 80000000>;
+ };
+
+ classd_gclk: classd_gclk {
+ #clock-cells = <0>;
+ reg = <59>;
+ atmel,clk-output-range = <0 100000000>;
+ };
+ };
+ };
+
+ qspi0: spi@f0020000 {
+ compatible = "atmel,sama5d2-qspi";
+ reg = <0xf0020000 0x100>, <0xd0000000 0x08000000>;
+ reg-names = "qspi_base", "qspi_mmap";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&qspi0_clk>;
+ status = "disabled";
+ };
+
+ spi0: spi@f8000000 {
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xf8000000 0x100>;
+ clocks = <&spi0_clk>;
+ clock-names = "spi_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ macb0: ethernet@f8008000 {
+ compatible = "cdns,macb";
+ reg = <0xf8008000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&macb0_clk>, <&macb0_clk>;
+ clock-names = "hclk", "pclk";
+ status = "disabled";
+ };
+
+ uart1: serial@f8020000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8020000 0x100>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@f8028000 {
+ compatible = "atmel,sama5d2-i2c";
+ reg = <0xf8028000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&twi0_clk>;
+ status = "disabled";
+ };
+
+ sckc@f8048050 {
+ compatible = "atmel,at91sam9x5-sckc";
+ reg = <0xf8048050 0x4>;
+
+ slow_rc_osc: slow_rc_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-accuracy = <250000000>;
+ atmel,startup-time-usec = <75>;
+ };
+
+ slow_osc: slow_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-osc";
+ #clock-cells = <0>;
+ clocks = <&slow_xtal>;
+ atmel,startup-time-usec = <1200000>;
+ };
+
+ clk32k: slowck {
+ compatible = "atmel,at91sam9x5-clk-slow";
+ #clock-cells = <0>;
+ clocks = <&slow_rc_osc &slow_osc>;
+ };
+ };
+
+ spi1: spi@fc000000 {
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xfc000000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@fc028000 {
+ compatible = "atmel,sama5d2-i2c";
+ reg = <0xfc028000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&twi1_clk>;
+ status = "disabled";
+ };
+
+ pioA: gpio@fc038000 {
+ compatible = "atmel,sama5d2-gpio";
+ reg = <0xfc038000 0x600>;
+ clocks = <&pioA_clk>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ pinctrl {
+ compatible = "atmel,sama5d2-pinctrl";
+ };
+ };
+ };
+ };
+};
Add device tree for SAMA5D2 Xplained board. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> --- arch/arm/dts/Makefile | 3 + arch/arm/dts/at91-sama5d2_xplained.dts | 200 ++++++++++ arch/arm/dts/sama5d2.dtsi | 671 +++++++++++++++++++++++++++++++++ 3 files changed, 874 insertions(+) create mode 100644 arch/arm/dts/at91-sama5d2_xplained.dts create mode 100644 arch/arm/dts/sama5d2.dtsi