diff mbox

ARM: dts: add rk3288-firefly-reload

Message ID 1468769937-23387-2-git-send-email-ayaka@soulik.info
State Not Applicable, archived
Headers show

Commit Message

Randy Li July 17, 2016, 3:38 p.m. UTC 
The Firefly RK3288 Reload is a combination Firefly rk3288 core board
with the Reload baseboard. Add a dtsi for the Firefly rk3288 core
which can be included into the dts for the various baseboards
in the future and dts for Reload base board.

Currently supported are serial console, wired networking, eMMC and
SD storage, SPFIF, IR receiver, LEDs, SDIO wifi and USB. But only
the OTG could work on the host mode now, the other USB host can't
work now, additional patches are required.

Signed-off-by: Randy Li <ayaka@soulik.info>
---
 Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi  | 304 ++++++++++++++++++++
 arch/arm/boot/dts/rk3288-firefly-reload.dts        | 320 +++++++++++++++++++++
 4 files changed, 629 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
 create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload.dts

Comments

Rob Herring July 17, 2016, 9:01 p.m. UTC | #1 
On Sun, Jul 17, 2016 at 11:38:57PM +0800, Randy Li wrote:
> The Firefly RK3288 Reload is a combination Firefly rk3288 core board
> with the Reload baseboard. Add a dtsi for the Firefly rk3288 core
> which can be included into the dts for the various baseboards
> in the future and dts for Reload base board.
> 
> Currently supported are serial console, wired networking, eMMC and
> SD storage, SPFIF, IR receiver, LEDs, SDIO wifi and USB. But only
> the OTG could work on the host mode now, the other USB host can't
> work now, additional patches are required.
> 
> Signed-off-by: Randy Li <ayaka@soulik.info>
> ---
>  Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
>  arch/arm/boot/dts/Makefile                         |   1 +
>  arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi  | 304 ++++++++++++++++++++
>  arch/arm/boot/dts/rk3288-firefly-reload.dts        | 320 +++++++++++++++++++++
>  4 files changed, 629 insertions(+)
>  create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
>  create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload.dts

Acked-by: Rob Herring <robh@kernel.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Heiko Stuebner July 18, 2016, 11:24 a.m. UTC | #2 
Hi Randy,

Am Sonntag, 17. Juli 2016, 23:38:57 schrieb Randy Li:
> The Firefly RK3288 Reload is a combination Firefly rk3288 core board
> with the Reload baseboard. Add a dtsi for the Firefly rk3288 core
> which can be included into the dts for the various baseboards
> in the future and dts for Reload base board.
> 
> Currently supported are serial console, wired networking, eMMC and
> SD storage, SPFIF, IR receiver, LEDs, SDIO wifi and USB. But only
> the OTG could work on the host mode now, the other USB host can't
> work now, additional patches are required.
> 
> Signed-off-by: Randy Li <ayaka@soulik.info>

looks mostly good, two small issues below. While I could replace the
io-domain node with the newer variant myself, the licensing issue will
require a resend anyway.

Please also carry over Rob's Ack in your resend as well.


> ---
>  Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
>  arch/arm/boot/dts/Makefile                         |   1 +
>  arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi  | 304
> ++++++++++++++++++++ arch/arm/boot/dts/rk3288-firefly-reload.dts        |
> 320 +++++++++++++++++++++ 4 files changed, 629 insertions(+)
>  create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
>  create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt
> b/Documentation/devicetree/bindings/arm/rockchip.txt index
> 715d960..3380212c 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.txt
> +++ b/Documentation/devicetree/bindings/arm/rockchip.txt
> @@ -31,6 +31,10 @@ Rockchip platforms device tree bindings
>      or
>        - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288";
> 
> +- Firefly Firefly-RK3288 Reload board:
> +    Required root node properties:
> +      - compatible = "firefly,firefly-rk3288-reload", "rockchip,rk3288";
> +
>  - ChipSPARK PopMetal-RK3288 board:
>      Required root node properties:
>        - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 414b427..8173e77 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -606,6 +606,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
>  	rk3288-evb-rk808.dtb \
>  	rk3288-firefly-beta.dtb \
>  	rk3288-firefly.dtb \
> +	rk3288-firefly-reload.dtb \
>  	rk3288-miqi.dtb \
>  	rk3288-popmetal.dtb \
>  	rk3288-r89.dtb \
> diff --git a/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
> b/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi new file mode 100644
> index 0000000..039ae16
> --- /dev/null
> +++ b/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
> @@ -0,0 +1,304 @@
> +/*
> + * Device tree file for Firefly Rockchip RK3288 Core board
> + * Copyright (c) 2016 Randy Li <ayaka@soulik.info>
> + *
> + * Licensed under GPLv2 or later.
> + */

please allow licensing under GPL and MIT licenses ... see license headers
of the other Rockchip boards. Same for the dts file below.


> +#include <dt-bindings/input/input.h>
> +#include "rk3288.dtsi"
> +
> +/ {
> +	memory {
> +		device_type = "memory";
> +		reg = <0 0x80000000>;
> +	};
> +
> +	dovdd_1v8: dovdd-1v8-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "dovdd_1v8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vcc28_dvp>;
> +	};
> +
> +	ext_gmac: external-gmac-clock {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <125000000>;
> +		clock-output-names = "ext_gmac";
> +	};
> +
> +	io_domains: io-domains {
> +		compatible = "rockchip,rk3288-io-voltage-domain";
> +		rockchip,grf = <&grf>;
> +
> +		audio-supply = <&vcca_33>;
> +		bb-supply = <&vcc_io>;
> +		dvp-supply = <&dovdd_1v8>;
> +		flash0-supply = <&vcc_flash>;
> +		flash1-supply = <&vcc_lan>;
> +		gpio30-supply = <&vcc_io>;
> +		gpio1830-supply = <&vcc_io>;
> +		lcdc-supply = <&vcc_io>;
> +		sdcard-supply = <&vccio_sd>;
> +		wifi-supply = <&vccio_wl>;
> +	};

io-domains are now a sub-device of the GRF, see
https://git.kernel.org/cgit/linux/kernel/git/mmind/linux-rockchip.git/commit/?h=v4.8-armsoc/dts32&id=3445b2fae55f1a232e6e4843f4f74de074d8c07f

Heiko
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Randy Li July 18, 2016, 3:32 p.m. UTC | #3 
Hi Heiko:

I use GPLv2 because of it looks more shorter, anyway I am back to allow
X11 now. The modification request of io-domain have been included.

Thank you for reviewing.

Randy Li (1):
  ARM: dts: add rk3288-firefly-reload

 Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi  | 339 ++++++++++++++++++++
 arch/arm/boot/dts/rk3288-firefly-reload.dts        | 356 +++++++++++++++++++++
 4 files changed, 700 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
 create mode 100644 arch/arm/boot/dts/rk3288-firefly-reload.dts
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 715d960..3380212c 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -31,6 +31,10 @@  Rockchip platforms device tree bindings
     or
       - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288";
 
+- Firefly Firefly-RK3288 Reload board:
+    Required root node properties:
+      - compatible = "firefly,firefly-rk3288-reload", "rockchip,rk3288";
+
 - ChipSPARK PopMetal-RK3288 board:
     Required root node properties:
       - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 414b427..8173e77 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -606,6 +606,7 @@  dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3288-evb-rk808.dtb \
 	rk3288-firefly-beta.dtb \
 	rk3288-firefly.dtb \
+	rk3288-firefly-reload.dtb \
 	rk3288-miqi.dtb \
 	rk3288-popmetal.dtb \
 	rk3288-r89.dtb \
diff --git a/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi b/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
new file mode 100644
index 0000000..039ae16
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-firefly-reload-core.dtsi
@@ -0,0 +1,304 @@ 
+/*
+ * Device tree file for Firefly Rockchip RK3288 Core board
+ * Copyright (c) 2016 Randy Li <ayaka@soulik.info>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include <dt-bindings/input/input.h>
+#include "rk3288.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0 0x80000000>;
+	};
+
+	dovdd_1v8: dovdd-1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "dovdd_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc28_dvp>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+	};
+
+	io_domains: io-domains {
+		compatible = "rockchip,rk3288-io-voltage-domain";
+		rockchip,grf = <&grf>;
+
+		audio-supply = <&vcca_33>;
+		bb-supply = <&vcc_io>;
+		dvp-supply = <&dovdd_1v8>;
+		flash0-supply = <&vcc_flash>;
+		flash1-supply = <&vcc_lan>;
+		gpio30-supply = <&vcc_io>;
+		gpio1830-supply = <&vcc_io>;
+		lcdc-supply = <&vcc_io>;
+		sdcard-supply = <&vccio_sd>;
+		wifi-supply = <&vccio_wl>;
+	};
+
+	vbat_wl: vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_flash: flash-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_flash";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_5v: usb-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc_flash>;
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>;
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	vdd_cpu: syr827@40 {
+		compatible = "silergy,syr827";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x40>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-enable-ramp-delay = <300>;
+		regulator-ramp-delay = <8000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vdd_gpu: syr828@41 {
+		compatible = "silergy,syr828";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x41>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	act8846: act8846@5a {
+		compatible = "active-semi,act8846";
+		reg = <0x5a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_vsel>, <&pwr_hold>;
+		system-power-controller;
+
+		vp1-supply = <&vcc_sys>;
+		vp2-supply = <&vcc_sys>;
+		vp3-supply = <&vcc_sys>;
+		vp4-supply = <&vcc_sys>;
+		inl1-supply = <&vcc_sys>;
+		inl2-supply = <&vcc_sys>;
+		inl3-supply = <&vcc_20>;
+
+		regulators {
+			vcc_ddr: REG1 {
+				regulator-name = "vcc_ddr";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vcc_io: REG2 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_log: REG3 {
+				regulator-name = "vdd_log";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			vcc_20: REG4 {
+				regulator-name = "vcc_20";
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			vccio_sd: REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd10_lcd: REG6 {
+				regulator-name = "vdd10_lcd";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcca_33: REG7  {
+				regulator-name = "vcca_33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vcc_lan: REG8 {
+				regulator-name = "vcca_lan";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vccio_pmu: REG9 {
+				regulator-name = "vccio_pmu";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vdd_10: REG10 {
+				regulator-name = "vdd_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vccio_wl: vcc_18: REG11 {
+				regulator-name = "vcc_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vcc18_lcd: REG12 {
+				regulator-name = "vcc18_lcd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	pcfg_output_low: pcfg-output-low {
+		output-low;
+	};
+
+	pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
+		bias-pull-up;
+		drive-strength = <12>;
+	};
+
+	act8846 {
+		pwr_hold: pwr-hold {
+			rockchip,pins = <0 1 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+
+		pmic_vsel: pmic-vsel {
+			rockchip,pins = <7 14 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+	};
+
+	gmac {
+		phy_int: phy-int {
+			rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_pmeb: phy-pmeb {
+			rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_rst: phy-rst {
+			rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/rk3288-firefly-reload.dts b/arch/arm/boot/dts/rk3288-firefly-reload.dts
new file mode 100644
index 0000000..8adda0a
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-firefly-reload.dts
@@ -0,0 +1,320 @@ 
+/*
+ * Device tree file for Firefly Rockchip RK3288 Reload base board
+ * Copyright (c) 2016 Randy Li <ayaka@soulik.info>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+#include "rk3288-firefly-reload-core.dtsi"
+
+/ {
+	model = "Firefly-RK3288-reload";
+	compatible = "firefly,firefly-rk3288-reload", "rockchip,rk3288";
+
+	leds {
+		compatible = "gpio-leds";
+
+		power {
+			gpios = <&gpio8 2 GPIO_ACTIVE_LOW>;
+			label = "firefly:blue:power";
+			pinctrl-names = "default";
+			pinctrl-0 = <&power_led>;
+			panic-indicator;
+		};
+
+		work {
+			gpios = <&gpio8 1 GPIO_ACTIVE_LOW>;
+			label = "firefly:blue:user";
+			linux,default-trigger = "rc-feedback";
+			pinctrl-names = "default";
+			pinctrl-0 = <&work_led>;
+		};
+	};
+	
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwr>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&hym8563>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable>;
+		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_host_5v: usb-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		regulator-name = "vcc_host_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+
+	vcc_otg_5v: usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc_otg_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+
+	/*
+	 * A TT8142 creates both dovdd_1v8 and vcc28_dvp, controlled
+	 * by the dvp_pwr pin.
+	 */
+	vcc28_dvp: vcc28-dvp-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dvp_pwr>;
+		regulator-name = "vcc28_dvp";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+		vin-supply = <&vcc_io>;
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power {
+			wakeup-source;
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Power";
+			linux,code = <KEY_POWER>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwr_key>;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+		simple-audio-card,dai-link@1 {  /* S/PDIF - S/PDIF */
+			cpu { sound-dai = <&spdif>; };
+			codec { sound-dai = <&spdif_out>; };
+		};
+	};
+
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+};
+
+&i2c0 {
+	hym8563: hym8563@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		interrupt-parent = <&gpio7>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_int>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	codec: es8328@10 {
+		compatible = "everest,es8328";
+		DVDD-supply = <&vcca_33>;
+		AVDD-supply = <&vcca_33>;
+		PVDD-supply = <&vcca_33>;
+		HPVDD-supply = <&vcca_33>;
+		clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
+		clock-names = "i2s_hclk", "i2s_clk";
+		reg = <0x10>;
+	};
+};
+
+&i2s {
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
+	card-detect-delay = <200>;
+	disable-wp;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdio0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-ddr50;
+	cap-sdio-irq;
+	disable-wp;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>, <&sdio0_int>;
+	vmmc-supply = <&vbat_wl>;
+	vqmmc-supply = <&vccio_wl>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&usb_host1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usbhub_rst>;
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&pinctrl {
+	ir {
+		ir_int: ir-int {
+			rockchip,pins = <7 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	dvp {
+		dvp_pwr: dvp-pwr {
+			rockchip,pins = <0 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	hym8563 {
+		rtc_int: rtc-int {
+			rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	keys {
+		pwr_key: pwr-key {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		power_led: power-led {
+			rockchip,pins = <8 2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		work_led: work-led {
+			rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmc {
+		/*
+		 * Default drive strength isn't enough to achieve even
+		 * high-speed mode on firefly board so bump up to 12ma.
+		 */
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+					<6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+		};
+
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdio {
+		wifi_enable: wifi-enable {
+			rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_host {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usbhub_rst: usbhub-rst {
+			rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	usb_otg {
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};