@@ -22,6 +22,17 @@ Required properties:
- interrupt-controller: Marks the device as a interrupt controller.
+Optional Properties:
+- oscio-is-gpo: Boolean, Indicated the oscio pin can be used as additional
+ output gpo port.
+
+- pull-up-ports: Array of port numbers which must have pull-up enabled.
+- pull-down-ports: Array of port numbers which must have pull-down enabled.
+- open-drain-ports: Array of port numbers which must be configured as open-drain,
+ Push-Pull mode is default.
+- polarity-invert-ports: Array of port numbers whih port polarity must be inverted.
+- probe-reset: Boolean, Indicates the expander must be resetted.
+
The GPIO expander can optionally be used as an interrupt controller, in
which case it uses the default two cell specifier as described in
Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
@@ -38,4 +49,10 @@ Example:
gpio-controller;
interrupt-controller;
+
+ pull-up-ports = <0 12>;
+ pull-down-ports = <1 8>;
+ open-drain-ports = <6 7 11>;
+ polarity-invert-ports = <3>;
+ probe-reset;
};
@@ -588,13 +588,16 @@ static void sx150x_init_chip(struct sx150x_chip *chip,
chip->gpio_chip.get = sx150x_gpio_get;
chip->gpio_chip.set = sx150x_gpio_set;
chip->gpio_chip.set_single_ended = sx150x_gpio_set_single_ended;
- chip->gpio_chip.base = pdata->gpio_base;
chip->gpio_chip.can_sleep = true;
chip->gpio_chip.ngpio = chip->dev_cfg->ngpios;
#ifdef CONFIG_OF_GPIO
- chip->gpio_chip.of_node = client->dev.of_node;
- chip->gpio_chip.of_gpio_n_cells = 2;
+ if (client->dev.of_node) {
+ chip->gpio_chip.of_node = client->dev.of_node;
+ chip->gpio_chip.of_gpio_n_cells = 2;
+ chip->gpio_chip.base = -1;
+ } else
#endif
+ chip->gpio_chip.base = pdata->gpio_base;
if (pdata->oscio_is_gpo)
++chip->gpio_chip.ngpio;
@@ -735,16 +738,70 @@ static int sx150x_install_irq_chip(struct sx150x_chip *chip,
return err;
}
+#ifdef CONFIG_OF_GPIO
+static u16 sx150x_of_probe_pins(struct device *dev, char *attr_name)
+{
+ struct property *prop;
+ const __be32 *p;
+ u16 pins = 0;
+ u32 u;
+
+ if (!of_find_property(dev->of_node, attr_name, NULL))
+ return 0;
+
+ of_property_for_each_u32(dev->of_node, attr_name, prop, p, u)
+ if (u < 16)
+ pins |= BIT(u);
+
+ return pins;
+}
+
+static struct sx150x_platform_data *sx150x_of_probe(struct device *dev)
+{
+ struct sx150x_platform_data *pdata = devm_kzalloc(dev, sizeof(*pdata),
+ GFP_KERNEL);
+ /* gpio_base is not needed with OF */
+
+ pdata->oscio_is_gpo = of_property_read_bool(dev->of_node,
+ "oscio-is-gpo");
+
+ pdata->io_pullup_ena = sx150x_of_probe_pins(dev,
+ "pull-up-ports");
+
+ pdata->io_pulldn_ena = sx150x_of_probe_pins(dev,
+ "pull-down-ports");
+
+ pdata->io_polarity = sx150x_of_probe_pins(dev,
+ "polarity-invert-ports");
+
+ pdata->irq_summary = of_irq_get(dev->of_node, 0);
+
+ /* irq_base is not needed with OF */
+
+ pdata->reset_during_probe = of_property_read_bool(dev->of_node,
+ "probe-reset");
+
+ return pdata;
+}
+#endif
+
static int sx150x_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
static const u32 i2c_funcs = I2C_FUNC_SMBUS_BYTE_DATA |
I2C_FUNC_SMBUS_WRITE_WORD_DATA;
- struct sx150x_platform_data *pdata;
+ struct sx150x_platform_data *pdata = NULL;
struct sx150x_chip *chip;
int rc;
- pdata = dev_get_platdata(&client->dev);
+#ifdef CONFIG_OF_GPIO
+ if (client->dev.of_node)
+ pdata = sx150x_of_probe(&client->dev);
+#endif
+
+ if (!pdata)
+ pdata = dev_get_platdata(&client->dev);
+
if (!pdata)
return -EINVAL;
In case of OF probing, the driver fails to initialize : - gpio_chip.base must be -1 - irq_summary must be either -1 or valid - There is no way to use the other configurations Add OF parsing function to complete the HW configuration, make OF configuration dynamic instead of static with #defines and update the DT bindings. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- Changes since v1 at http://lkml.kernel.org/r/1466157063-10955-1-git-send-email-narmstrong@baylibre.com: - Put back #ifdef CONFIG_OF_GPIO to remove OF code for non-of platforms .../devicetree/bindings/gpio/gpio-sx150x.txt | 17 ++++++ drivers/gpio/gpio-sx150x.c | 67 ++++++++++++++++++++-- 2 files changed, 79 insertions(+), 5 deletions(-)